Search Documents

By Booth S. A, Milton D. W

Stratabound/stratiform and remobilised mineralisation have been recognised as the two dominant styles of mineralisation which constitute the Broken Hill ore deposit. Recognition of prospective sites for accumulation of ore depends on understanding the heterogeneity of the ore environment and the distribution of the two styles of mineralisation. The internal stratigraphy of the Broken Hill ore deposit and its enveloping rocks, is described, and a generalised stratigraphic setting of the stratiform mineralisation is outlined. Fhiphasis is placed on the existence of closely-spaced sub-basins as potential sites for ore accumulation close to the Broken Hill ore deposit. Further from the immediate ore environment, recognition of the same diagnostic stratigraphic sequence

Jan 1, 1983

By O. D. Gonzalez, R. A. Oriani

The migration of hydrogen and of deuterium dissolved in a iron and in nickel induced by an applied electrical potential has been measured over a range of temperature. In all cases the intevstitial solute migrates to the cathode. The deduced charges of transport are positive, independent of or slightly dependent on temperature, and markedly larger for the beavier mass. These results are interpreted as showing predominating momenlum transfer between electron holes and the acticated complex of the elementary diffusion act. THE migration of components of a metallic system under the action of an applied electrical potential is called electromigration or electratransport. This phenomenon has been known since 1861 and is becoming of increasing interest to metal scientists because of the opportunity it offers to explore the connections between mass transport and electron transport. Until recently, reliable data have been very scarce because of the difficulties inherent in the measurements. In addition, theoretical understanding has been either nonexistent or rudimentary and at present this situation is only moderately improved. Whereas the prevalent notion had been (and is still widely held) that electromigration directly reflects the state of ionization of a component in its equilibrium state in the metal, it is now becoming clear that the major, if not the sole, factor is the momentum transfer between the charge carriers, themselves in motion because of the applied field, and the metallic components in their activated state. It becomes important therefore to obtain reliable data over a range of temperature on electrornigration in systems where only one component moves, that is, either in pure metals (vacancy motion) or in interstitial solid solutions. Our choice of systems was dictated by our measurements' of the Soret effect in solid solutions of hydrogen and deuterium in iron and nickel. Indeed, the main reason for making measurements on electromigration at all is that we suspected a mechanistic connection between thermal diffusion and electromigration. In our former paper' we proposed that what is common to both phenomena is the momentum transfer between the charge carriers in the metal and the atom as it jumps from one equilibrium position to another. In Soret diffusion, however, there is in addition the dissipation of the energy of the jumping atom via pho-nons. We have since found that similar ideas for this interconnection have been developed by Fiks.2 In the present paper we will discuss in more detail our understanding of the mechanism of electromigration itself, but we turn first to a presentation of the experiments and results. EXPERIMENTS AND RESULTS Let us consider a metallic system in which only one component, m , can diffuse at the temperature in question, and to which are applied simultaneously an electrical potential gradient, grad cp, and a chemical potential gradient, grad p,. One may write3 for the material flux Jm and the electronic charge flux Je by applying the condition, grad = 0, to Eq. [I] and evaluating grad(um/T) for the isothermal case and for activity coefficient independent of composition over the relevant composition range. ere, c is the concentration and D the diffusivity of the mobile component. The experimental technique that we have used to measure Z* for the isotopes of hydrogen individually dissolved in each of two transition metals has been developed from a method used by Wagner and Heller.4 (A somewhat similar method was also used by Herold.5) A wire or thin rod of the metal under study connects two volumes of gaseous hydrogen at identical pressures; hence grad um = 0. A direct current is made to pass through the specimen, serving to maintain the specimen at the desired temperature and also to produce the electromigration of the hydrogen dissolved in the metal in equilibrium with the gaseous hydrogen. Under these conditions, the flux of hydrogen from one volume to the other is given, from Eq. [I] for grad( um/T) =0by

Jan 1, 1968

By Mohammad Reza Khalesi, Ruhollah Rezazadeh, Mohsen Izadi Yazdan Abadi, Mahmoud Abdollahy

"The rotary vacuum drum filter (RVDF) is widely used for dewatering in mining industrial. In general, different parameters have influence in the solid-liquid separation such as: solid percent, level of vacuum, particle size distribution, filter cloth and chemical additives. These parameters can influence on some variables such as cake moisture, throughput and filter cloth life time. The aim of this study is to propose some chemical additives to improve the rate of filtration and decrease cake moisture of Gol-E Gohar iron ore concentrate by using laboratory scale bottom feed vacuum filter and suggest a filter cloth with long life time (more than 400 hours). Effect of particle size distribution on filtration investigated in large scale by measuring the thickness of cake and cake moisture.Increasing molecular weight of anionic flocculant lead to increases throughput but cake moisture increases too; While the filter aid increases throughput and decreases cake moisture simultaneously; the combination of them show different behavior. TSS and filter cloth life time have directly relation with material and type of filter cloth weave. Depending to type of feed, two polyester and polypropylene filter cloth are suggested. More over twill and satin weave have the best results. To prove the laboratory results some industrial tests performed in Gol-E Gohar hematite iron ore concentrate plant.INTRODUCTION“The process of grinding and classification involves the use of large quantities of water. The separation of solids from liquids is usually achieved by gravity sedimentation in thickeners. For fine particles this is a slow process. In general, 75–80% of the water can be separated and removed by thickeners. For further water removal, filters are used where in excess of 90% of the water can be removed” (Gupta, 2006).“Many types of filters are available, which are broadly classified here as vacuum, pressure, precoat and depth filters. Each classification contains a number of sub-processes. A category of filter that uses vacuum induced driving forces and semipermeable media to facilitate the separation of solids from suspension. While pressure differences across the filter are limited to less than 85 KPa (usually 75 KPa), most units are capable of processing a wide range of feed materials in a continuous manner” (Rushton, 2008)."

Jan 1, 2016

By Weijie Wei, Jinwang Zhang, Shengli Yang

Due to the unbalanced top coal drawing process, the recovery ratio is low, and the equipment stability is poor in the longwall top coal caving mining (LTCC) with an inclined seam. Aimed at these problems, this paper proposes the dynamic group caving method (DGCM). The basic procedure is that when the drawn volume of top coal from a support reaches about half, the next support begins drawing top coal, and the drawing process between the two supports is half done. Taking the panel no. 8103 in Beixinyao mine as the research object, the characteristics of drawing body shape, particle movement trace, and variation of recovery ratio are investigated by using Particle Flow Code. Furthermore, the effect of mining-caving ratio on the top coal drawing law under DGCM is revealed by the simulation results, and compared with the single-opening sequence caving method (SSCM) and the doubleopenings sequence caving method, advantages of DGCM are determined in inclined seams. The results show that the drawing body can be divided into the left and the right under DGCM. Specifically, the drawn top coal particles in the left are from the upper part of this support, that in the right are from the lower part of next support, which verifies the correctness of the theoretical analysis. The characteristics of the drawing body shape are more significant when the mining-caving ratio is relatively small. In addition, with increasing mining-caving ratio, the recovery ratio of the panel both increases gradually underDGCMand SSCM.When the miningcaving ratio is less than 1:1, the recovery ratio of DGCM is obviously higher than that of SSCM, indicating that DGCM can greatly improve the recovery ratio. While when the mining-caving ratio is larger than 1:1, the recovery ratio of two caving methods is basically equal; however, the advancing time is significantly shortened under DGCM. This study are of great significance to realize high efficiency and precise caving in LTCC with an inclined seam.

Jul 7, 2020

By R. L. Bolmer

Rapid depletion of our known mineral resources has stimulated exploration for new mineral deposit. Abandoned mines or prospects may prove to be commercial in today's economy. Often it is necessary to revaluate such properties. Some of these may be inaccessible because of caving of flooding. Many, however, remain in good condition, except that over the years the air in the workings has become depleted of oxygen. Each year the Bureau of Mines receives numerous requests for aid in entering old mines, the air in which is incapable of supporting life. Requests of many individuals who wish to examine or explore-such places with the help, of the Bureau's self-contained oxygen breathing apparatus have been denied because of the hazards involved in the use of this equipment for such purposes. The distance to be traveled in irrespirable gases may be too great for safety; under favorable conditions, a round trip of 2,000 feet from fresh air is the maximum distance that may be traveled.3/ The use of such equipment is hazardous unless a team of at least 5 men thoroughly experienced in its use is provided; and when extensive traveling from. a fresh-air base is required, a reserve team should be provided.3/ Usually, the apparatus is requested for use in exploring workings having only one surface connection, as mines having more than one opening usually are more easily ventilated;,and in some natural ventilation is sufficient or can be made so by cleaning out obstructed openings.

Jan 1, 1951

By Lucas Nana Wiredu Damoah, Lifeng Zhang

"Increasing demand for Solar Grade Silicon (SoG-Si) due to rising interest in renewable energy has lead to increased SoG-Si Top – cut scraps generated from the multi-crystalline silicon making process. Due to the high cost of SoG-Si and the potential to use the top-cut scraps as feedstock material, there has been increased effort to develop cost effective and efficient technologies. As a result, several methods to recycle the top-cut scraps are currently been applied, and researched. These include settling under gravitation field, which is a slow process to be industrially applicable. Natural settling of inclusions by gravitational force is a slow process and not attractive to the industry. Recent experiments on Top-cut SoG-Si scrap under high frequency, high voltage, electromagnetic field showed that SiC inclusions settled within a short time to the bottom of the crucible and the characteristic rod-like morphologies of Si3N4 inclusions in SoG-Si were not detected. This study investigates the enhanced settling of SiC inclusions and the behavior of Si3N4 particles under the influence of high frequency, high voltage, electromagnetic field in Top-cut SoG-Si.IntroductionThe photovoltaic industry depends on silicon based PV materials either as single-crystalline silicon, or multi-crystalline Si (MC-Si), or amorphous Si [1] for over 90 % of its market share. [2] MC-Si produced by directional solidification of solar grade silicon melt dominates the silicon PV market. During the directional solidification process, SiC and Si3N4 particles within the melt are pushed by the solidification front to the top of the ingot which is the last to solidify. Therefore the top of the ingot is cut generating what is known as top-cut solar silicon scraps. The Si3N4 particles are mainly from the coating material at the inside surface of the silica crucible and from air absorption during the solidification process. The SiC particles mainly stem from the carbon reduction process of the primary production of silicon [3]. Due to the growth of the PV industry as a result of global demand for clean, reliable, and affordable energy [4], there is the need to develop new methods to compliment exiting ones to recycle SoG-Si waste (e.g. top-cut) for sustainability."

Jan 1, 2012

By Moraka N. V., van Rensburg M. Jansen

"SynopsisGoing beyond transformation claims contained in employment equity scorecards and industry compliance reports, this article provides qualitative insight into the initiatives employed and challenges experienced by mining companies in a quest to transform the mining industry. Perceptions expressed during in-depth interviews with 10 senior executives showed that the assumption that mining companies are reluctant to transform is erroneous. Results from this study suggest buy-in and commitment to transformation. This article describes specific initiatives undertaken by mining companies to transform. The most notable initiatives include staff recruitment efforts to appoint historically disadvantaged South Africans (HDSAs), staff development initiatives, as well as community development. The findings furthermore contextualize the challenges experienced by industry participants in their quest to transform. Despite accusations that industry participants are not taking responsibility for the implementation of the transformation agenda, government needs to recognize that they too have a role to play and need to appreciate and assist in the current challenges experienced by the industry.IntroductionWe need a mining sector that works. Mining employs over half a million people. It is the biggest earner of foreign exchange in our country. It also contributes about 20 billion rand directly to tax revenue. Mining also makes a far larger contribution as a buyer of goods and services, and a supplier of inputs to other sectors of our economy and other economies around the globe’ said President Jacob Zuma during the 2014 State of the Nation Address (Zuma, 2014). However, despite apparent commitment from government, enforced compliance with social and labour plans, regulations and Mining Charter targets, the South African mining industry is slow to gain local and international investor trust (Deloitte & Touche, 2013; Mashego, 2013).Industry players acknowledge that their context has changed – creating various challenges (Davis, 2014). In the past few years, such challenges included subdued commodity prices, increased working costs, constrained infrastructure, and high labour costs, coupled with poor levels of productivity, strained labour-management relations, an uncertain regulatory environment, and the inevitable maturation of the industry (Deloitte & Touche, 2013; Davenport, 2014). Mining affected communities also became more cognisant of their rights, and politicians more vocal in their expectations from their relationships with the mining giants (Davis, 2014). One of the main issues that contributed to the difficult operating conditions was claims from organized labour and Minister Shabangu that this industry is too slow to transform. Specific claims were made in terms of employment equity, fair salaries and wages for mineworkers, housing and living conditions, health and safety issues, and general working conditions (Limpitlaw et al., 2005; Miningmx, 2013; Shabangu, 2010). These claims were followed by what Gill Marcus, Reserve Bank Governor, explained as ‘unprotected strike action [that] has escalated into an uncontrolled, violent and unlawful landscape, led by a mob mentality in the absence of formal and recognised leaders’ (Mavuso,2013)."

Jan 1, 2015

By D. A. Rice

In pelletizing magnetic iron ore concentrates, about 6 to 18 lb of bentonite binder are added per ton of concentrate during balling to give green and dry strengths to the unfired pellets. The dry bentonite is mixed into the filtercake following the magnetic concentration circuit of the plant. The filtercake contains about 10% moisture, and the water may be of highly variable composition, depending on the particular concentration circuit, its source, and the ore being treated. A knowledge of the parameters that influence the balling operation is essential for optimal efficiency in producing balls strong enough to survive the treatment during transportation from the balling device to the furnace and during the firing operation. Furthermore, very weak unfired pellets probably contribute to high dust losses and poor furnace control. The factors that determine the strength of unfired pellets have received considerable study (1,2,3,4). Tigerschiold and Ilmoni(l) pointed out the significance of the surface area of the particles being pelletized. Merklin and Childs(2) reported on the effect of material size consist, chemical additives such as soda ash, lime, balling time, ball size, and the moisture content of green balls. Iwasaki and Zetterstrom(3) examined the detrimental effects of fatty acids on the pelletizing process. Stone(4) correlated the zeta potential of bentonites with the strength of unfired pellets. He found that, in general, a high negative charge on the bentonite is conducive to good balling. Although studies of pelletizing in the iron ore industry deal with a complex multicomponent system consisting mainly of the iron mineral, bentonite, and water, the last of these has received little attention, particularly with regard to the possible effects of mill water chemistry on the pelletizing process and the strength of unfired pellets. It is widely known that the composition of mill process water is an important variable in unit operations such as flotation, thickening, and filtering and that impure water can lead to poor metallurgical results. The results of the present study indicate that the chemistry of the mill water may be an important variable in the balling operation as well. Knowledge about this variable should contribute to lowering bentonite and oil consumption and to improving furnace performance. Such knowledge can also assist those who use balling in evaluating commercial bentonites for plant use as well as those investigating balling from a more fundamental point of view In this study we have examined 1) the effects of replacing mill process water in the magnetic concentrate filtercake with pure water, and 2) the effects of several chemical impurities that are commonly found in mill process waters upon the strength of unfired pellets. The results are interpreted in terms of the zeta potential of the bentonite and magnetite particles. The data lend support to a suggested mechanism whereby the electrostatic attraction of oppositely charged particle surfaces causes bentonite-bentonite and magnetite-bentonite bonding. This mechanism would also explain why several chemical additives e.g., sodium carbonates and phosphates, have such marked effects on increasing the strength of unfired pellets.

Jan 1, 1971

This paper outlines mining practice in the South Alligator valley between 1954 and 1964. The valley is situated in the Northern Territory 130 miles south east of Darwin and trends north west. The centrally located El Sherana camp is 219 miles by road from Darwin via Pine Creek on the Stuart Highway. 64 miles of gravelled road with low level bridges and culverts which were completed in 1959, connect Pine Creek with El Sherana. This road is often impassable during severe wet season conditions. Earliest recorded production was during the years 1956-57 from the El Sherana and Palette miles, by shallow open cut and cut and fill stoping from small shafts. 4600 tons of high grade ore was processed by hand sorting of massive pitchblende followed by gravity concentra- tion. At the same time 627 tons of ore was won from a small open cut at Sliesbeck 35 miles SE of El Sherana. The second and most important phase of production was to fill two small contracts with the United Kingdom Atomic Energy Authority (U.K.A.E.A.) totalling 700 tons of U 08. About 144,000 tons of ore was mined from widely separated smal' orebodies and mining practice varied from small open cuts to gloryholes, open stoping and cut and fill stoping. In some orebodies a combination of several methods was employed to complete production. Final deliveries were made to the U.K.A.E.A. In 1964.

Jan 1, 1968

By William G. Pariseau

Solvay Chemicals Company mines trona in south-central Wyoming and has done so for many years. The mine is one of several in a mid-continent sedimentary basin that hosts the largest trona resource in the world. Trona is an evaporite, a sesquicarbonate that occurs in several seams of varying thicknesses and depths. Trona is processed into soda ash which has a number of industrial uses in the manufacture of glass, detergent, paper and chemicals. Figure 1 shows the location of the Solvay Mine. A ventilation shaft was recently excavated at Solvay Chemical Company’s mine in the trona patch. In fact, a 22 ft (6.7 m) diameter shaft (inside diameter) was bored upwards from the 1500 ft (457 m) level to the surface. The first bored section was 26 ft (7.9 m) in diameter that allowed for a 2 ft (0.6 m) thick concrete liner. This section began at a depth of approximately 1500 ft (457 m). A second bored section was 24 ft, (7.3 m) in diameter that allowed for a 1 ft (0.3 m) thick concrete liner. This section began at a depth of approximately 750 ft (229 m). This shaft is the #5 Shaft. Figure 2 shows the cutter head used to excavate the shaft.

Feb 1, 2025

By D. M. Hausen

It has been demonstrated that microscopic techniques can be applied in a practical manner to the study of spodumene liberation in the processing of pegmatitic ores at the Kings Mountain spodumene plant, Kings Mountain, North Carolina. Spodumene and associated non-opaque gangue minerals are identified and quantified by microscopic point-counting of polished thin sections of heads, concentrates, middlings and tails fractions. Specially prepared polished thin sections? provide uniform thickness of particles for measurement of diagnostic optical properties and the alternate use of incident and transmitted light in distinguishing the various gangue and ore minerals. Spodumene is commonly associated and interlocked with quartz, albite, microcline and muscovite. Concentrate grade depends on the degree of spodumene liberation, which in turn depends on the crystal size and textural association of interlocked minerals. The liberation of spodumene can be measured as a function of screen size by means of microscopic point-count data. Microscopic data also provide useful metallurgical information about the nature of diluent minerals in spodumene concentrates, and the form of lithia losses in the tails. Lithium assays correlate closely with microscopic spodumene analyses in various flotation products from Foote Mineral's Kings Mountain plant, and confirm the applicability of quantitative optical microscopy to the study of liberation and recovery of spodumene from pegmatitic ores. A better understanding of recovery-grade relationships was developed as a result of quantitative microscopy studies.

Jan 1, 1981

By C. E. Armantrout, H. Kato, M. I. Copeland, M. Krug

The investigation of the nickel - gadolinium phase diagram was undertaken to determine the alloying behavior of these two metals . The data from meltingpoint determinations , thermal analyses , metallographic examinations , and X- ray diffraction analyses revealed a phase diagram with three eutectic points and seven intermetallic compounds . Very limited solubility of the phases in each other was observed . The five phases , Ni Gd , Ni , Gd , Ni Gd , Ni, Gd , and NiGd¸ , melted incongruently at about 1,300 ° , 1,270 ° , 1,180 ° , 1,070 ° , and 775 ° C , respectively . Ni Gd and NiGd melted congruently at approximately 1,550 ° and 980 ° C , respectively . Four of the compounds were determined to crystallize in the hexagonal system : Ni Gd , Ni Gd , Ni , Gd , and Ni Gd . Ni Gd was determined to be cubic and NiGd , orthorhombic . The crystal system of NiGd was not determined . The eutectic points occurred at 13 , 67 , and 85 wt pct gadolinium , and the isotherms at 1,290 ° , 890 ° , and 700 ° C , respectively .

Jan 1, 1964

By R. E. Ogilvie, N. L. Peterson

Diffi-lsion measurements were conducted at all compositims in the bcc solid solution of the U-Nb system employing incremental couples at composition intemals of 10 at. pct. Diffusion coefficients were determined by the Matano method from concentration gradients obtained with the electron-probe microanalyzer. The activation energy for inter-diffi-lsion as a function of compositim shows three distinct regions: 1) 80 to 100 pct U.6= 30 kcal per mole; 2) 20 to 80 pct U, $ - 70 kcal per mole; 3) Oto 20 pet U, Q = i40 kcal per mole. The frequency factor, fi0 and the activation energy $ were found to be roughly related by the following equation: log Do ^9.7 X IO-5Q -6,6. The Kirkendall marker movement indicates that DU is larger than DNb between 16 and 100 pct U and DNb is larger than DU from 0 to 4 pct U. FOR practical as well as fundamental reasons, the rates of diffusion in alloys are of considerable consequence. Most solid-state reactions are largely dependent upon the diffusion of atoms through the lattice structure and along grain boundaries. The high-temperature strength and reasonable nuclear properties of niobium have prompted its use as a reactor material in contact with uranium fuel. Hence, diffusion data for the U-Nb system are of considerable importance. In the previous diffusion study1 on the U-Nb system using pure element couples, reliable data were obtained only in the range of 0 to 10 at. pct Nb due to the large variance of the diffusion coefficient with composition. Also, a large Kirkendall effect and considerable porosity in the uranium-rich areas of the specimen were reported, which suggests that the true diffusion coefficients are somewhat larger. The purpose of the present study was to obtain reliable diffusion coefficients at all compositions using incremental diffusion couples with intervals of 10 at. pct. In view of the abnormal self-diffusion be- havior of y uranium2-4 and some other bcc transition elements,&apos;-&apos; it was felt that a comparison of the interdiffusion coefficients in the bcc U-Nb system with those of Reynolds et al.9 for the fcc gold-nickel system might shed some light on the diffusion mechanism involved. Both systems have similar phase diagrams, in that complete solid solubility exists above a miscibility gap. EXPERIMENTAL PROCEDURE The uranium used in this investigation was obtained through the courtesy of Argonne National Laboratory. An analysis of this material detected only Si-30, A1-7, C-6, N < 10 and 0-18 ppm. The niobium was electron-beam melted material obtained from Stauffer-Temescal. The gaseous impurities were less than 50 ppm, and the spec troc hemical analysis showed Ta-500 and W-200 ppm. U-Nb alloys were prepared at composition intervals of 10 at. pct by melting the appropriate amounts of the pure elements in an arc furnace. The buttons were inverted and remelted 6 times to assure complete mixing. The buttons were then wrapped in molybdenum foil, canned in Zircaloy-2 or stainless steel, and hot rolled 30 pct reduction in thickness at temperatures between 850" and 1100°C. Alloys with 10, 20, 30, 40, and 90 at. pct Nb rolled quite easily under these conditions, but the 50, 60, 70, and 80 pct alloys remained brittle. After melting and rolling (when possible), the alloys were annealed for 24 hr at a temperature within 100°C of their melting point in a dynamic vacuum of better than 4 x 10-8 mm Hg. These treatments produced alloys which were homogeneous on a 1 p scale within the detectability limits of the electron probe. During fabrication, the alloys picked up as much as 100 ppm Mo and 100 ppm Zr. Other elements checked for but not found were Co, Cr, Fe, Mn, Ni, and Ti. The grain size of the annealed samples ranged from 3 mm for the uranium-rich alloys to 0.3 mm for the niobium-rich alloys. This permitted measurements of the concentration gradients in the diffusion samples without crossing more than one or two grains, thereby eliminating any grain boundary effects. The specimens were bonded by theU&apos;picture frame" technique as reported by Kittel.10 Specimens of composition b)U + (100 - x)Nb were sandwiched between two specimens of composition (x + 10)U + (90 - x)Nb after they were ground flat and parallel

Jan 1, 1963

By Onuralp Yucel, Ahmet Turan, K. Can Candeger

Exothermic riser sleeves are important tools to increase solidification duration, particularly for iron-steel casting. Increasing the time to solidus improved casting product quality by minimizing cavities. Therefore, process costs were significantly reduced. In comparison with the use of unsleeved risers, exothermic riser sleeves retain up to 30–35% of the heat and increase the duration to solidus by nearly 50%. Exothermic riser sleeves are a mixture of metallothermic-based exothermic and insulating materials that are manufactured in different sizes and shapes. Various suppliers produce these sleeves in different compositions. However, the designers must clearly understand the thermochemical and thermophysical properties. The purpose of the present study was to experimentally determine the effects of varying experimental parameters such as reaction duration, flammability and temperature change etc. on selected exothermic sleeves. The results were compared with thermodynamical simulations which were performed using the contents and the corresponding thermophysical properties of exothermic sleeves.

Mar 1, 2018

By G. L. Smit

The Buffelsfontein Gold Mining Company is situated in the Klerksdorp district of the Province of the Transvaal in the Republic of South Africa, approximately 100 miles west of Johannesburg. Gold production commenced in January 1957 and Uranium treatment of residue slimes as a by-product started in July 1957. The mining property is 5435 mining claims in extent, the equivalent of 7988 acres or 12.5 sq miles. The mine was initially exploited by the Pioneer Twin Shaft System, consisting of a 26-ft diam down-cast shaft and a 22 ft-diam up-cast shaft, sunk in the north-west area of the mine to cater for the hoisting and ventilation requirements for a milling rate of 150,000 tons per month. To exploit the Eastern zone of the property and assist in increasing production to 200,000 tons milled per month, it was decided to sink a further Twin Shaft System consisting of a 28-ft diam downcast shaft and a ventilation up-cast shaft -22-ft in diam, both monolithic concrete lined — 200 ft apart and 5300 ft deep. This paper deals with the sinking and commissioning of these Eastern Twin Shafts. This was achieved by one sinking crew within a period of 20 months. A) PLANNING 1) Siting: The Eastern Shaft System was sited in the north-east area of the property, 12,000 ft east on strike from the Pioneer System. (Fig. 1). Initially the system was sunk to the 5300 ft elevation to conform with the original Pioneer Shaft System. On completion a sub-vertical main shaft will be sunk to the 8000 ft elevation in the immediate vicinity, and subsequently the surface ventilation shaft will be deepened to this elevation by raising from level to level and sliping to full size. The exact positions of the shafts were chosen after: a) underground development had located certain known water bearing zones, and b) geophysical and topographical surveys had been carried out. The shafts passed through the following geological succession: Surface to 4430 ft - Dolomites of the Transvaal System 4430 to 4470 ft - Quartzites and conglomerates of the Black Reef Series of the Transvaal System. 4470 to 4470 ft - Diabasic Lava of the Venters-dorp System (Ventersdorp Contact Reef at base). 4470 to 5250 ft - Quartzites of the Elsburg Series of the Upper Witwaters-rand System. The shafts were sited to ensure that the least possible water would be encountered during sinking, and this contributed to the rapid rate of sinking. 2) Duties: a) The 22-ft diam ventilation shaft was designed to up-cast 1,400,000 cfm of air (0.060 density) against a resistance of 22 in. water gauge. b) The main shaft was designed to handle 160,000 tons hoisted per month as well as the men, material and down-cast ventilation to serve this tonnage. The 284 diam main shaft is equipped with streamlined buntons spaced at 15 ft centers set in pockets which were left during sinking. There are six compartments, four of which are sewed by two dual purpose hoists, hoisting either, twedeck man cages or 13-ton bottom discharge skips. The other two compartments are served by a single purpose winder hoisting double deck cages accommodating 60 men per deck. (Fig. 2). 3) Timing: Permanent equipment was ordered well in advance to insure continuity in the operation. Development underground reached the shaft positions before the start of sinking operations. From this development, boreholes were drilled into shaft positions to drain off water in the vicinity of the shafts. To ensure complete co-ordination of effort, all relevant data, as well as the allocation of responsibility, were made known to all persons and departments concerned. 4) Models: The extensive use of scale models during the preliminary planning stages proved most useful in deciding on design such as buntons, bunton pockets and guide cleats, and complex layouts concerning loading, spillage and pumping arrangements. (Fig. 3). These models also proved invaluable in determining the walling routine. Normal working conditions could

Jan 1, 1964

By M. Askari, A. Ahmadi

"This study was conducted to establish the possible application of bioleaching in the pilot scale to recover valuable metals from the sulfidic tailings of Golgohar Iron Mine (Kerman, Iran). Using bioleaching processes, solvent extraction and sulfide precipitation recovery of valuable metals including, copper, cobalt and nickel from the tailing was investigated. The results showed that the optimum pH and temperature conditions relative to the bioleaching step was 1.5 and 45°C. The extraction of the metals from the low grade polymetal resource with complex mineralogy is very important from economic, environmental and technical point of views. Moreover, the proposed method has some advantages from energy saving, tailing management and creating added value from waste materials aspects.INTRODUCTION The growing demand for base metals and strategic such as: copper, nickel and cobalt as well as high-grade resource depletion has caused them, the mining industry to extract metals from low-grade resources and driven by complex mineralogy (Xie et al., 2005). Economic extraction of metals with low grade sources requires low-cost and efficient processing methods. A source with enormous potential for metals in future, secondary sources, such as: tailings mineral industries which the lack of appropriate technology and the high cost of processing weren't recoverable with previous procedures in the past. But it is possible that with develop new and efficient technologies have the economic exploitation ability. Recovery of metals from tailings resources is very important not only in terms of precious metals but also in terms of reducing environmental problems (due to heavy metals). The metals of copper, nickel and cobalt are mainly like sulfide compounds in the nature, usually for their recovery, first they make ore with flotation method to obtain the sulfide concentrate that containing valuable metals. then for the metal production, it will be melt and purification. Due to the environmental aspects, technical problems in the recovery of base metals from low grade ore and mixes, the presence of small reserves, in the past three decades they pay much attention to the use of hydrometallurgical processes for the recovery of base metals from these resources. These processes are classified according to the solver agent to leaching sulfates, chlorides, nitrates and amines (Hackl, 1995). Early, chloride leaching under oxidation condition in acidic or alkaline solutions was recognized the best process to produce sulfide concentrates. But then the basic processes sulfates was considered as the superior process because of being easier, a better understanding of the chemistry of leaching and recovery of base metals, especially copper from the environment easier sulfate solution with an organic solvent extraction and electro winning. The bioleaching is shown its ability on a commercial scale of low-grade sulfide minerals and ore that because of environmental reasons, the possibility of melting is not possible to them. The existing industrial base factories are based on primarily on the bioleaching and pressure leaching and recovery of cathode copper sulfate solution by extraction with organic solvents (SX) and electrowinning (EW) (Wang, 2005). Preliminary analysis has shown that valuable elements such as copper, nickel and cobalt are in the float flotation unit. Hence the plan to extract these metals from the wet tailing stream has been done."

Jan 1, 2017

By MAURICE SUNKPAL, Taghi Sherizadeh, Kutay E. Karadeniz, Dogukan Guner, Samuel Nowak

Despite numerous empirical, numerical, and hybrid studies conducted on the subject of coal rib failure, mine fatalities related to rib failures continue to occur at around 1.5 per year between 2009 and 2021. To date, a standard methodology for the design of coal rib supports that can accommodate the wide range of unique conditions found in coal mines in the USA has not been developed, forcing mine operators to rely on the trial-and-error process or industrial legacy practices for the design of coal rib support patterns. In this study, to better understand the support systems’ effectiveness, various rib bolting scenarios were investigated. A coal mass constitutive model is implemented to a distinct element method (DEM) code, and rib factor-of-safety (RibFOS) analyses were performed by applying strength-reduction for the coal matrix and explicitly modeled face cleats. Ribs with various overburden depths and mining heights composed of solid Banded-Bright coal (BBC) were considered in this study. Different scenarios such as rib bolt length and the number of bolts were studied to quantify the effect of primary rib support density on rib stability. As a result of the unsupported coal rib analyses, a decaying exponential relationship is proposed between the mining height-overburden depth and the RibFOS. The developed coal rib models clearly show the coal-rib bolt interaction and illustrate how the addition of rib bolts restricts the movement of the coal rib. The results reveal that the strength reduction method in DEM code with the coal-mass model can aid in the development of practical primary support charts, which can help in the rib support design process. In addition, an unsupported RibFOS cutoff is proposed, beyond which the addition of primary support cannot stabilize the failed rib structure.

Aug 5, 2023

By X. Q. Jiang, D. L. Chen, A. Macwan

Magnesium alloy, being the lightest structural material, is a key candidate for the weight reduction of vehicles in automotive and aerospace industries; however, its poor corrosion resistance and difficulty in deformation are limiting factors. Recently, Al/Mg/Al tri-layered clad sheets have been considered as a promising alternative to improve corrosion resistance and formability of magnesium alloys. The aim of this study was to evaluate the tensile properties and deformation behavior of Al/Mg/Al tri-layer clad sheets at different temperatures and strain rates. Yield strength (YS), ultimate tensile strength (UTS), and elongation were observed to increase with increasing strain rate. With increasing temperature from -40°C to 180°C, YS and UTS decreased and ductility increased. The strain hardening exponent evaluated via three equations of Hollomon, Swift, and Afrin et al. showed a similar increase with increasing strain rate and decreasing temperature. The fractographic analysis showed partial debonding of clad interface especially at higher strain rates and lower temperatures.

Jan 1, 2015

By A. O. Orumwense

Mill circumferential speed, the number of passes of pulp through the grinding chamber, media type, size and filling ratio were investigated in an attempt to determine how to effectively grind copper concentrates in a stirred mill. The stirred mill product fineness was enhanced to some extent by decreasing media size, high media filling, and an increased number of passes of the pulp through the grinding chamber. Shape also plays a major role in grinding media effectiveness, with spherically shaped media producing a finer size. The fineness of the product increases with increasing power consumption but the method of energy transfer is very important in energy utilization. The effect of the mill parameters on copper flotation was evaluated. Copper recovery was influenced by grinding media size, mill speed and the number of pulp passes through the grinding chamber.

Jan 1, 2006

By Arno C. Fieldner

The determination and publication of data o the chemical and physical properties of American coals have been primary functions of the Bureau of Mines since its creation in 1910. In recent years this program has been expanded to meet increasing needs for information on the suitability of coals for the production of coke, gas, and byproducts, and within the last year an experimental coal-hydrogenation plant has been completed. With this addition, the Bureau is able to cover every phase of coal utilization, including combustion, carbonization, liquefaction, and complete gasification. The need for this information is increasing not only to meet the requirements of consumers but also to give the data required to establish the classification and minimum selling price of coal by the National Bituminous Coal Commission.

Jan 1, 1938