Search Documents

By K. Kim

An analysis was conducted to determine the effects of blasting on slope stability and downstream comminution processes. To investigate these effects, the extent of blast-induced rock damage and the magnitude of induced stress were examined. This analysis showed that damage may extend up to 500 meters (1MPa, tensile strength) in the rock mass, a distance that is sufficient to impact the pit-scale slope over the long term. In addition, the damage zone was calculated using the reasonable assumption that compressive waves are the primary agent in microfracturing during blast fragmentation. The calculated damage zone ? up to 5.6 meters (30MPa, 30% of the compressive strength) ? indicates that microfracturing can occur throughout the entire rock mass in the blasting area. Finally, an economic analysis was conducted by comparing two reasonably assumed blasts in a copper mine. The change in energy required for crushing and grinding was demonstrated using Bond?s law after increasing the blast energy from 180kcal/t to 350kcal/t. A total cost saving of 13.3% ($9.4M) was achieved with the increase. An optimal blast design should consider both slope stability (safety) and downstream comminution energy (production).

Feb 23, 2014

By Nagahiro Saito, Takashi Nishimura, Takamichi Ichikawa, Akio Fuwa

"Yttria-stabilized zircohia (YSZ) has high potential to be used as solid-oxide fuel cell (SOFC) electrolyte. However, the high efficiency of SOFC has not been yet achieved due to the high internal resistance of bulk electrolyte. The resistance becomes lower with the decrease in the electrolyte thickness. Thus, the decrease in electrolyte thickness leads to lower internal resistance. . The aim of this study is as follows: (a) to prepare the thin films of YSZ by inductively-coupled RF plasma-enhanced metal organic chemical vapor deposition (PEMOCVD) process using Zr(t-OC4H9)4,Y(DPMh and oxygeil, and (b) to reveal the relationship between the structural characterizations and the process parameters.1. IntroductionYttia-stabilized zirconia (YSZ) has, been widely used as not only heat-resistant materials but also the components in automotive oxygen sensors, electrolytes of solid-oxide fuel cell (SOFC)(1)(2) and the buffer layers for the high-temperature superconductor because of its low thermal conductivity, good mechanical properties and high ionic conductivity. However, it is said that the internal resistance of the bulk electrolyte is too high to be appropriate as a solid electrolyte for high-efficient SOFC. The authors believe that the thin YSZ electrolyte can give a high performance to characteristics SOFC, since the internal resistance becomes lower with the decrease of electrolyte thickness. Thus the process technology to prepare YSZ thin films is desirable and must be established.In recent years, the YSZ thin films have been reported by chemical vapor deposition (CVD), thermal CVD using metal chlorides (MC) of ZrCl4 and YC(3)(4), thermal CVD using metal organic compounds (MO)(5)(10) Zr(t-OC4H9)4 and Y(C11H19O2)(11) and plasma-enhanced (PE) CVD using MO. Here, these methods are called MCCVD, MOCVD and PEMOCVD. MCCVD has two disadvantages; a large quantity of chlorinated impurities in deposited films and high processing temperature (> 1273K). This high processing temperature leads to damage of substrates in particular, so the application of this technology is limited. On the other hands, the processing temperature by MOCVD becomes and is lower. Unfortunately, the accurate vapor pressures of these metal organic compounds have not been, known so: that it is difficult to control the composition and the film thickness by MOCVD method well. Moreover, the large amount of carbonic compounds in the films prepared by MOCVD method is produced. However, plasma-effect has been reported to decrease large amount of the carbonic impurities by PEMOCVD. However, PEMOCVD has many reaction parameters in plasma processing; the geometry of experimental apparatus, radio frequency, electronic power input and so on. Thus, the general understanding about the relationship among reaction parameters, the composition and crystal structure of thin deposit film by this method has not yet been established."

Jan 1, 2000

By Y. J. Cao

The purpose of this study was to investigate the flotation behaviour of unburned carbon in a cyclonic-static microbubble flotation column (FCSMC). The ash sample, collected from a power station in Guangdong province of China, was characterized by size analysis, X-ray diffraction, contact angle measurements, and X-ray fluorescence. The effect of the column flotation operating variables on the removal of unburned carbon from the fly ash was systematically studied. The feasibility of separating unburned carbon and ash was determined from the removal rate of unburned carbon (RUC) and loss on ignition (LOI). Within the range studied, the optimum diesel oil dosage was 1200 g/t, abies oil dosage was 600 g/t, pulp density was 20 per cent, superficial gas velocity was 1.4 cm/s, and circulating pressure was 0.20 MPa. The results indicate that the FCSMC technique is effective in removing the unburned carbon from the fly ash, which can be attributed to the generation of microbubbles and the continuous cyclonic circulation method. Under the optimized conditions, a cleaning ash with 2.13 per cent LOI and 94.21 per cent RUC was obtained.

Jan 1, 2012

By M F. Lee

Although the Mt Charlotte gold resource was discovered in 1893, it was only in 1954 that geologists correctly interpreted drill data and defined a large low-grade orebody. The mine has been a large, low-cost and profitable producer since 1962 when bulk mining commenced using cut and fill. From 1968 a combination of long hole open stoping with delayed mass blasting was used. This proved to be an excellent mining method for the large, separate subvertical orebodies. The structured but otherwise good quality rock allowed very large stopes to stand unsupported. Exceptionally large equipment, for its time, was used to efficiently mine, muck and move the ore at low-cost. The mine only just survived severe cost pressures in 1974-76, due to very low gold prices. Better gold prices in 1979 and a need to access deeper ore meant a bold commitment to sink the Cassidy Shaft and refurbish the mine to sustain future profitability. In 1997 the Sam Pearce Decline connected to the underground workings, making it profitable to mine upper level remnant ore. Mining-induced seismicity has been a feature of mining at Mt Charlotte. The main cause has been shearing on structures. A mine-wide seismic system was installed in 1994. Large seismic events have occasionally made management question whether a safe working environment can be maintained. Thorough investigations led to an understanding of the problem and development of procedures to minimise seismicity.

Jan 1, 2000

By B. Z. Zhong, T. Ong, W. E. Wallace, W. Z. Whong, Z. W. Gu, M. J. Keane

"Abstract-Diesel emission particles (DEP) from an engine operating on the Federal Test Procedure VDC were dispersed in an aqueous mixture of dipalmitoyl lecithin (DPL). a major component of pulmonary surfactant and saline and were tested for genotoxicity using the unscheduled DNA synthesis (UDS) assay with autoradiography techniques in cultured Chinese hamster lung cells. A DEP sample from the same source was dispersed in dimethyl sulphoxide (DMSO) and subjected to the same assay. Both dispersions (in DPL and DMSO) were found to induce UDS in a dose-related manner. After separation of the sample into supernatant and sediment fractions. the activity of the DEP sample was found to reside in the supernatant fraction for the DMSO-dispersed sample; and in the sedimentary fraction for the surfactant-dispersed sample. These findings further indicate that genotoxic activity associated with DEP inhaled into the lung may become bioavailable through the dispersion properties of pulmonary surfactant components.INTRODUCTIONTHE mutagenicity of diesel emission particles (DEP) has been studied intensively (LEWTAS and WILLIAMS, 1986). Carcinogenic effects of diesel exhaust in exposed animals have been reviewed (NIOSH, 1988) and an evaluation of carcinogenic risks to humans from diesel engine exhausts has been published (IARC, 1989). Using components of pulmonary surfactant such as dipalmitoyl lecithin (D PL), dipalmitoyl phosphatidylethanolamine (DPPE) or dipalmitoyl phosphatidic acid (DPPA) dispersed in physiological saline, we have previously shown that diesel soots express mutagenic activities in the Salmonella histidine reversion assay system and in the sister chromatid exchange assay using the cultured Chinese hamster lung (V79) cells. Mutagenic activity of diesel soots dispersed in DPL, DPPE and DPPA was quantitatively comparable to and in some cases greater than, the activity expressed by an equal mass of soot extracted by dichloromethane-dimethyl sulphoxide (DCM-DMSO) (WALLACE et al., 1989).Unscheduled DNA synthesis (UDS) is accepted and frequently included, as one of the tests in the battery of assays used to assess carcinogenic-mutagenic potential -of chemicals (MITCHELL et al., 1983). In this study, induction of UDS in V79 cells by DEP, dispersed in the major component of pulmonary surfactant DPL, was carried out. The purpose of this study is to validate the suggestion generated from our previous work that mutagens associated with inhaled particles may be dispersed or solubilized in the phospholipid component of pulmonary surfactant and become active in such a phase (WALLACE er al., 1989) and to test the fractionated DEP sample using UDS assay for a more complete evaluation of its genotoxicity."

Dec 1, 1995

By Steven B. Van Kouteren

Added value is a term loosely used in the industry, but what exactly does it mean? What does it take to make a value-added product and more importantly how does a company maintain the value added to its products? Most people agree that value-added means the value of a mineral minus the cost to produce it. But what is misleading is that producing value added products does not necessarily guarantee the profitability of the products. In some cases firms that make "value-added" products are not very profitable. It is not only important to understand how to make a value-added product but also how competitive forces in the market can erode the value added. Therefore, when we look at value-added opportunities, we must understand how to obtain the value added and more importantly how to maintain the value. There are four major factors that limit a company's ability to add value to its products. This paper will examine these factors and will use the ground calcium carbonate and mica industries as examples.

Jan 1, 1990

By Preston McGrain

Geologic maps are indispensable tools in the modern search for mineral and fossil-fuel resources. They are the first essential step in understanding the lithologic nature and structure of rock units that form the land surface and that lie beneath it. They provide the basic foundation for planning mineral resource exploration programs and form the superstructure from which subsurface investigations are projected. In view of the economic application of such maps, the Commonwealth of Kentucky and the Federal Government entered a formal agreement in 1960 to map Kentucky geologically on a scale of 1:24, 000, or one inch map distance equals 2,000 feet on the ground. A 7. 5-minute quadrangle would comprise the unit map area. A resolution which urged the preparation of a new geological map of the entire State was passed by the Kentucky Society of Professional Engineers in February 1959, and was presented to the Governor of Kentucky, the Legislative Research Commission, Kentucky Department of Economic Development (now Department of Commerce), Kentucky Chamber of Commerce, and Kentucky Geological Survey with a request for support and action. The request was subsequently endorsed and actively supported by numerous civic and professional societies as well as representatives of various facets of Kentucky government, commerce, and industry. Monies to initiate the program were appropriated by the next session of Kentucky legislature; this appropriation was matched by federal funds (Hagan, 1961). Kentucky's state-wide topographic mapping project was completed in 1956, just four years prior to starting the geologic mapping program. The recently completed modern 7. 5-minute, 1:24,000 topographic maps made ideal bases for plotting areal geology. Had they not been available, it is doubtful if a geo- logic mapping program so large and comprehensive could have been undertaken.

Jan 1, 1966

By P. G. Kovalchik

Recent research conducted by NIOSH, Pittsburgh Research Laboratory showed that electrical current levels permitted under present regulations may not limit cable temperatures to less than 90°C in reeled trailing cables. Reeled cables, tightly wrapped with many turns, all carrying current in an enclosed space, can become overheated due to poor heat transfer. This overheating can cause the cable insulation to soften and become easily damaged. The damaged insulation reduces the life of the cable and can lead to shock, electrocution, and mine fires. This paper describes a method of measuring the conductor temperature of mine trailing cables during normal operation. The temperature is measured using a 50/125 micrometer Graded Index Multimode Optical Fiber located in the center of the metallic conductors. Distributed temperature measurements are made using an Optical Time Domain Reflectometer (OTDR). This system is capable of measuring temperature with an accuracy of plus or minus one degree centigrade over a length of 4 km at 1-m intervals. With this unique way of measuring temperature, tests can be conducted simulating actual mine conditions and provide important data to allow MSHA's Approval and Certification Center to develop approval criteria for cyclically rated reeled machines.

Jan 1, 1998

By J. E. Hilliard, H. E. Cook

It is shown that for systems having a miscibility gap the spinodal composition (c,) in the vicinity of the critical temperature (Tc) is related to the equilibrium composition (c,) by where cc is the critical composition. This expression is exart for the limit T — Tc and is a good approximation down to (T/Tc) - 0.9. If the miscibility gap meets the composition of the pure components THE recent theoretical treatment by cahn1,2 on spinodal decomposition of solid solutions has revived interest in methods of estimating the chemical spinodal, * i.e., the locus on a binary phase By use of the appropriate expression, the spinodal can be drawn on the Phase diagram almost by inspection with an accuracy comparable to that of lengthy calculations in which a free-energy function is fitted to the phase diagram. Satisfactory agveemenf is also obtained with spinodals comPuted from experimental free-energy curves. where G is the Gibbs free energy of the homogeneous solution and c the atomic fraction of component 2, the derivative being evaluated at constant temperature (T) and pressure (P). (These subscripts will hereafter be omitted from the partial derivatives.) If experimental measurements of G as a function of c and T are available in a single-phase region above the spinodal, then these can be extrapolated to obtain a series of metastable free-energy isotherms in the two-phase region, and from these isotherms a series of spinodal compositions can be calculated. Because the value of is very sensitive to experimental errors, an elaborate analytic procedure is required for

Jan 1, 1965

By Takashi Sasaoka, Pinyo Meechumna, Hiroshi Takamoto, Pipat Laowattanabandit, Akihiro Hamanaka, Kikuo Matsui, Hideki Shimada

"The EGAT Mae Moh coal mine is an open-cut coal mine in Thailand that produces about 16 million tons of lignite annually to generate 2,400 mw of electricity. The surface mine pit covers is 4 by 7 km (2 by 4 mi) with mining depths ranging up to 260 m (853 ft). A large pit slope is formed with the progression of the mining operation. However, massive slides in the pit slope often occur due to weak planes, such as faults and bedding, and the weak mechanical properties of the rocks. Hence, a 200-300 m (656-984 ft) boundaries of rock block including coal seams is left in front of faults in order to prevent slides and maintain the stability of the pit slope. As a result, there are significant coal reserves beneath the abandoned area along the pit slope.The focus of this paper is on the applicability and design of the highwall mining for recovering much of the coal left along the pit slope.INTRODUCTIONThe EGAT Mae Moh Mine is located about 630 km (186 mi) north of Bangkok, Thailand (see Figure 1). It is the largest coal mine in Thailand and produces about 16 million tons of lignite annually from open-cut mining (70 % of the total coal produced in Thailand). The coal is used to generate 2,400 mw of electricity at the Mae Moh power plant, which is situated near the mining area. The mine pit covers an area of 4 by 7 km (2 by 4 mi) at varied depths up to 260 m (583 ft) as shown in Figure 2. As the mining operation progresses, the pit becomes to be deeper and deeper. In the year 2035, the bottom of the pit is expected to reach depths of 500-600 m and the open-cut mining operation will be finished. The possibility of an underground mining operation is being investigated.A large pit slope is formed with the progression of open-cut mining. However, massive slides often occur in the pit slope along weak planes including faults and bedding planes due to the weak nature of the rock. As a result, 200 to 300 m (656 to 984 ft) boundaries of rock including coal seams are left in place in front of faults to prevent slides and to maintain the stability of pit slope. Moreover, the dip of the slope is less than that of the planned design. As a result, there significant coal reserves abandoned along the pit slope."

Jan 1, 2010

By A. G. Doll

The Bond low energy impact (crushing) work index test is specified to be performed on rock specimens between 50 mm and 75 mm in effective diameter. NQ-diameter drill core, frequently used in mineral exploration programs does not meet that specification, it being 45 mm diameter or less. This paper reports the effect of performing the impact test on contiguous sections of HQ diameter and NQ diameter core, exploring the hypothesis that the contiguous intervals give equivalent results in spite of the core diameter difference.

Jan 1, 2012

By AIME AIME

IN accordance with the custom of recent years, the Institute joined with the Western Division of the American Mining Congress in holding a joint meeting at Joplin on Sept. 28, 29 and 30. Actually the meeting might be said to have begun on the 27th, since the Engineering Education Committee held two sessions on that day, which are reported on another page. In addition to these sessions there were informal gatherings in the Hotel Conner, which was the headquarters, on the golf links and elsewhere of all those who had arrived by Sunday morning. The technical sessions were formally opened on Monday morning by Robert E. Tally who, after suitable preliminary remarks, introduced A. Scott Thompson, of Miami, Okla. Mr. Thompson in welcoming the visitors to the Tri-State district said that it had come to be known as a poor man's country and at the present price of zinc did not find it difficult to live up to its name. He also referred to the work Mr. Tally had done for the stabilization of the mineral industry. H. Foster Bain, in responding to this address for the Institute, said that mining men generally felt at home in Joplin, that the solutions of their problems and the general practice that had been developed in the district were not only of great interest to them, but that visitors could learn much

Jan 1, 1931

By József Faitli, Barnabás Csoke, Károly Solymár, Zoltán Hatvani, Dimitri Papanastassiou

"Grinding has a significant economic impact on ore dressing/processing, therefore the sizing of mills has an outstanding role.In most cases, the sizing of dry or wet mills for ore processing is primarily based on the determination of the Bond grindability index, using the Bond-Kjos-Rowland relations. In several cases, grinding takes place under conditions different from these and the grinding conditions have a great influence on the post-grinding process. This is particularly true for the grinding of bauxites where grinding takes place in alkali, often in higher temperature (up to 100 ºC) in alkali Liquor. So it is necessary to develop a testing method providing a reliable grindability index even under these special circumstances (grinding in alkalis medium at different temperatures) and allowing a more precise mill sizing. The new heated mill is suitable to determine the grindability index under temperature-controlled circumstances, in liquids with different temperatures (water, alkali). This paper presents in detail the equipment, the conditions (parameters) of the testing process for wet and alkaline grinding, the measuring results and the conclusions."

Jan 1, 2003

By Haydn H. Murray

Although alumina constitutes about ii percent of the earth's crust, it is expensive to separate and purify for the production of aluminum with the exception off the alumina in bauxite. The United states has a variety of non-bauxite resources that could substitute for bauxite, including high alumina clays, alunite, dawsonite in oil shale, anorthosite, and nepheline syenite. Each of these resources are discussed from the standpoint of geology, geography, processing, potential recovery, and environmental problems. Potential by-products include silica from clays, potash and sulfuric acid from alunite, soda ash from dawsonite, and soda ash and potash from anorthosite and nepheline syenite.

Jan 1, 1982

By Peter N. Calder

The selection of a slope angle for an open pit in rock has often been made without the benefit of a comprehensive engineering study. This is largely due to the fact that the hardware and procedures necessary for such a study have not been available. Recently this situation has been reversed. The application of borehole television and terrestrial photogrammetric devices has made possible the accurate determination of rock joint structure, on which stability calculations can be based. Another important aspect is the evolution of practical methods of conducting in-situ rock joint strength tests.

Jan 1, 1971

By S. K. Kawatra

In this paper three methods of on-stream analysis 1) Radiometric techniques, 2) X-ray tube techniques and 3) Neutron activation method are reviewed. Advantages and disadvantages of each method are discussed.

Jan 1, 1984

By D. I. Hoyer

A preliminary model has been developed for autogenous pebble milling using information obtained from studies on ball milling and SAG milling. The model treats the breakage as the weighted sum of first-order breakage of smaller particles by tumbling pebbles, non-first order breakage of larger particles which are too large to be nipped properly by pebbles, autogenouS fracture and chipping of larger lumps to form pebbles, and autogenous fracture and abrasion of pebbles. The model includes the effects of residence time distribution, classification through the exit grate, and a mass transfer relation which describes the accumulation of fine material in the mill. Example simulations are given, based on breakage parameters determined from batch grinding tests in laboratory mills. fracture breakage and abrasion. In the development of these preliminary mass balance equations it will be assumed that breakage by fracture is first-order, but this assumption will be modified later in the paper. It will also be assumed that the residence time distribution of a long autogenous mill can be described by an equivalent series of m fully-mixed mills, with a classification action imposed on the mill contents by the discharge grate. Size distributions are expressed as a v2 geometric series, numbered 1 for the top size down to n for the fines, or "sink" interval. If the holdup in the mill is W then the rate of breakage of material in size interval i is given by SiwiW, where wi is the fraction of material in size interval i, and Si is -the overall specific breakage rate of size i material (fraction per unit time).

Jan 1, 1985

2nd CONGRESS OF THE INTERNATIONAL SOCIETY FOR ROCK MECHANICS The 2nd Congress of the International Society for Rock Mechanics will be held in Belgrade, 21-26 September, 1970. The Congress will include: working sessions, study tours, receptions, excursions introduced in the working sessions and post-congress excursions and special programme for accompanying persons. Anyone interested in rock mechanics and its applicarion may take part in the 2nd Congress. Official languages of the Congress are: English, French and German. Simultaneous translation service will be provided during the Congress. All the correspondence concerning the 2nd Congress of the International Society for Rock Mechanics should be addressed to: Sekretarijat 2. kongresa Medjunarodnog drustva za mehaniku stena Institut za vodoprivredu "Jaroslav Cerni" Bulevar vojvode Misica 43, Postanski fah 530 Beograd - Jugoslavija NINTH INTERNATIONAL SYMPOSIUM TECHNIQUES FOR DECISION MAKING IN THE MINERAL INDUSTRY The Symposium which is to be held in Montreal during the week of June 14-19, 1970, follows the Computer Symposium held in Salt Lake City this year. The purpose of the Symposium is to define the role of decision making techniques within the mineral industry and to stimulate the development of specific applications. The subject of the Symposium-mathematics, operations research and computers as applied to the mineral industry-allows a complete picture of the mineral industry in its public policy, corporate, financial and technological environment to emerge. This is another of the series of symposia on this and related subjects started in the early 1960's at the University of Arizona. Sponsorship has included a number of Universities and the Society of Mining Engineers of the American Institute of Mining. This 1970 symposium is the first to be held outside of America, and is being sponsored by the Canadian Institute of Mining, McGill University and Ecole Polytechnique. A number of delegates from South Africa have participated in these symposia and several have already arranged to attend this symposium in Montreal. Enquiries should be directed to: Secretariat, The 9th International Symposium, Department of Mining Engineering, Ecole Polytechnique, P.O. Box 50l, Snowden, Montreal 248, Quebec, Canada. 24th INTERNATIONAL GEOLOGICAL CONGRESS This Congress is to be held in Montreal, Canada, from August 21 to 30, 1972. A very detailed and extensive programme has been proposed, and includes a number of excursions. Copies of the first circular are obtainable from: The Organizing Committee, 24th International Geological Congress, 601 Booth Street, Ottawa 4, Ontario, CANADA. SYMPOSIUM ON THE RECOVERY OF PYRITE The proceedings of the Symposium on the Recovery of Pyrite, held in Johannesburg on 12th to 13th June 1969 are now available. Copies may be ordered from the Secretary, S.A.I.M.M., P.O. Box 61019, Marshalltown, Transvaal at a cost of R10.00. Papers and addresses presented at the Symposium were: Opening Address by Mr J. K. E. Douglas (President). 'The world sulphur position,' by W. C. J. van Rensburg (Member). 'The South African sulphur position,' by D. L. Taylor (Member). 'The recovery of pyrite at Government Gold Mining Areas Limited,' by R. J. Westwood (Member), G. S. Stander (Affiliate) and H. R. Carlisle (Member). 'Recovery of pyrite concentrates from colliery-waste discards-A preliminary assessment,' by W. A. Gilbert (Visitor) and E. A. Nugent (Member). 'The role of pyrite in upgrading the uranium content of Witwatersrand conglomerate ores by means of the heavy-medium separation process,' by D. J. Tutt (Associate Member). 'Pyrite recovery by jigs at Durban Roodepoort Deep Limited,' by E. J. Dominy (Affiliate), F. Diamond (Affiliate) and A. D. Graham (Affiliate). 'The storage of pyrite concentrates,' by Joan C. Campkin (Visitor) and P. J. Lloyd (Member). 'The flotation plants of the Anglo- Transvaal Group,' by L. A. Bushell (Member). 'Pyrite flotation with amines and cyanidation of the products,' by E. H. D. Carman (Member). 'Gold recovery by cyanidation from mill products obtained after pyrite flotation,' by P. G. Mrkusic (Graduate), M. Sciarone (Visitor) and H. E. Simonsen (Visitor). 'The influence of sulphydral and cationic flotation reagents on cyanidation of native gold,' by K. G. Ashurst (Visitor) and W. P. Finkelstein (Member). 'Laboratory tests on the flotation of pyrite from Witwatersrand gold ores by cationic collector,' by J. Levin (Member), and M. L. Veitch (Visitor). Closing Address, by Dr R. E. Robinson (Director, National Institute for Metallurgy).

By Arthur R. MacPherson

Primary autogenous grinding has been in general use for somewhat over 20 years. During this period there have been many highly successful plants built on this principle, while some others have had problems such as: 1. Not performing as predicted from test work. 2. Highly fluctuating tonnage rates. 3. Mechanical problems. 4. High liner wear. Many of the problems with commercial autogenous mills have resulted from improper sampling and testing of the ore during the development period. It is recognized that the fully autogenous mill is very sensitive to any changes in grindability which may occur in the feed to such a mill. The semi-autogenous mill is somewhat less sensitive, but large swings in grindability of the feed require adjustment of ball charge and this cannot be easily accomplished in a short period of time.

Jan 1, 1976

By T. G. Mayhew, A. A. Bergeron, R. J. Mahany

This report describes an operational communications system which provides remote intra-terrestrial wireless transmission of environmental information. Design and modification specifications of requisite equipment are included along with a detailed description of system operation

Jan 9, 1976