Search Documents

By E. Ghali, A. D. Bas

"Treatment of oxide, e.g. roasted gold ores has received relatively less attention than sulphidic ones and recently, handling of oxide gold ores is becoming essential. In this study, the influence of roasted gold ore (RGO) slurry (at 35% solid ratio) on the electrochemical dissolution of gold has been examined using pure gold and iron oxide minerals (hematite, maghemite, and magnetite) as disc electrodes by zeroresistance ammeter mode either in one or two separate containers. The presence of slurry decreased galvanic currents, i.e. corrosion rates due to the release and increase in the amount of soluble and/or insoluble species that could retard further the anodic behaviour of gold. Higher galvanic currents were observed in two separate containers than that in one container indicating the primary importance of galvanic interactions. SEM-EDS results observed iron hydro/oxide coatings on gold surface in case of magnetite test. However, in case of RGO electrode it is not a perfect passivation, although somewhat decreasing trend was observed on gold dissolution. These findings have revealed that passivation is not only a laboratory phenomenon, but also it could be responsible for the slowdown of gold dissolution in industrial practice.INTRODUCTIONThe cyanidation of gold is an electrochemical corrosion process thus; the dissolution of gold can readily be studied by electrochemical techniques. The outcome/summary of previous electrochemical studies of gold leaching can partially be summarized as follows: Filmer (1982) and Lorenzen and van Deventer (1992) reported the negative effect of pyrite and pyrrhotite on gold leaching due to the galvanic interactions; Aghamirian and Yen (2005) studied gold galvanic corrosion in presence of sulphide mineral electrodes only in one cell using zero-resistance ammeter (ZRA) mode; Dai and Jeffrey (2006) discussed, individually, the anodic and cathodic behaviours between gold and sulphide minerals, and Azizi et al. (2010, 2011) used a bed reactor to examine the influence of sulphide minerals on gold dissolution in one and two separate cells. Accordingly, a slowdown in gold leaching has generally been attributed to the passivation phenomenon, although the indication of this phenomenon is still an undergoing debate. For instance, Mrkusic and Paynter (1970) identified the passivation as the film formation of dissolved species from calcine, Crundwell (2014) explained passivation, in the case of corrosion of metals, as the formation of a layer which is composed of a new chemical species on the mineral surface and this layer inhibits or blocks further reactions. He suggested that passivation is related to the oxidation of the metal, and the formation of a passive layer that retards the rate of dissolution by several orders of magnitude. Consequently, galvanic interactions, passivation phenomena, or combinations of them are considered significant electrochemical factors affecting gold dissolution (van Deventer, Reuter, Lorenzen, & Hoff, 1990; Azizi, Petre, & Larachi, 2012). It is important to note that generalizing the influence of a mineral/metal on gold dissolution may not be correct in all cases, since contrary behaviours/results (for pyrite) have been observed (Aghamirian & Yen, 2005). Therefore, electrochemical study of gold is still a subject of research and need to be examined further in detail."

Jan 1, 2016

By H. R. Shakeri, R. Mayer, M. J. Worswick, A. Rahem

The current focus of research and development in transportation industry is to use lightweight materials such as aluminium alloys for more structural components. In this regard, maintaining safety of the passenger and vehicle is the most important; therefore crashworthiness of components made of lightweight materials must be evaluated prior to sizable application of these materials. The focus of the present study is to understand failure and damage mechanisms during the axial crushing of aluminium tubes made of A1Mg3.5Mn alloy of 2 and 3.5 mm thickness. Due mainly to complexity of the crushed tubes, a microstructural approach is considered. In this study optical, stereo as well as scanning electron microscopy techniques have been used to study damage and failure mechanisms in these types of tubes, which are essential energy absorbing components in passenger vehicles.

Jan 1, 2006

By Francisco Cubillos, Jorge Menacho, Cesar Gomez, Juan Rodríguez

Mineral flotation is the most used process to selectively separate particles of one or more minerals of interest. The process uses natural or induced hydrophobicity to collect particles on the surface of rising bubbles through collisions and formation of bubble-particle aggregates. Flotation machines must keep particles in suspension and well distributed, while at the same time, disperse a mass of air into a population of small bubbles. The efficiency of the separation depends primarily on the characteristics of the bubble population generated in the machine and its distribution and flow throughout its volume. The formation and separation of bubble-particle aggregates create two zones, with strong interactions between them, and with markedly different hydrodynamics conditions. A model describing two-phase hydrodynamics of the continuous and dispersed phases (frother solutions and bubbles, respectively), moving along the whole unit, is proposed. Bubble populations are characterized at the formation stage including the effect of the presence of frothers. Flow through the aggregates formation zone, where bubbles move freely and are closely spherical, is modeled using drift-flux analysis. In the aggregates separation zone, bubbles initially pack maintaining a water layer thick enough to prevent capillary forces to affect their shape. As water drainage proceeds, bubbles deform, capillary channels form, and a network of channels with a diameter size distribution develops; channels become narrower (permeability is reduced) as the distance from the interface increases. Froth hydrodynamics is characterized using models originally developed to describe unsaturated flow through porous solid particle beds. Effects of hydrostatic pressure are considered.

Jan 1, 2014

By A. S. Hewitt

After an interval of fourteen years, saddened for all of us by the death of David Thomas, the father of the anthracite iron-trade, first president of the Institute, and by the untimely loss of his successor, Alexander L. Holley, whose memory we are about to honor by loving services, the members of the American Institute of Mining Engineers have conferred upon me for the second time the office of president, under circumstances similar to those which led to the choice in 1876. Then the whole world was represented at the great exposition of industry which was held in Philadelphia to celebrate the one hundredth anniversary of our declaration of political independence. In 1890 it is our privilege to receive as guests the members of the British Iron and Steel Institute, who, with singular and graceful felicity, have appointed a meeting in the United States in the year when we pass from the second to the first place in the international column of the production of iron, and thus celebrate our industrial independence. For the honor of being chosen to extend to our distinguished guests the right hand of fellowship and a hearty welcome I return to my associates the grateful acknowledgment of one whose chief claim to your favor is to be found in his love for the professional occupation in which we are all engaged, and in his efforts, public and private, to promote its advancement into new fields of usefulness. In order to indicate the full significance of the visit of our foreign guests at this time, it will be proper to explain briefly the origin, aims and work of the Iron and Steel Institute. It unquestionably owes its birth to the International Expositions held in London in 1851 and 1862, and in Paris in 1867. These expositions served to break down the jealousies of nationality and to diffuse a better knowledge of industrial processes. Trade-secrets, which had been carefully guarded, became common property; manufacturers who had previously regarded themselves as rivals formed bonds of union and ties of friendship, as the results of an intercourse which

Jan 1, 1891

By C. Chingwaru, W. Chingwaru, J. Vidmar

"Zimbabwe is endowed with rich deposits of minerals such as diamonds, platinum, coal, uranium, lithium, gold, antimony, iron, and chrome. Bioleaching has been implemented as an efficient and low-cost method to extract metals such as copper, cobalt, and gold from sulphide and/or ironcontaining ores and mineral concentrates in a number of countries around the globe. Zimbabwe, despite being a world leader in mineral wealth, has gone through years of economic stagnation which have brought with them energy shortages. Bioleaching is an innovative way to recover minerals from ores using relatively low-capital-cost and non-polluting technology. Principally, iron- and sulphur-oxidizing bacteria can be used to oxidize iron and sulphide to ferric iron and sulphuric acid, respectively, and the ferric iron oxidizes the insoluble metal sulphides to soluble metal sulphates that can be readily recovered from solution. Although some minerals such as gold are inert to biological reactions, they can be liberated using bacteria that act on certain types of ores and other minerals that co-occur with these minerals. The geology of the mineralized areas in Zimbabwe, rich in chalcopyrite / pyrite, allows a number of microorganisms to be used for the extraction of minerals by bio-oxidation. This paper reviews the potential of bioleaching in the country. IntroductionZimbabwe has rich deposits of minerals including diamonds, platinum, coal, uranium, lithium, gold, antimony, iron, and chrome. Bioleaching is defined as the use of microorganisms to facilitate the extraction of metals from sulphide or iron-containing ores or concentrates (Rawlings, 2004, 1997). Bioleaching has been shown to be an efficient (Blowes, Ptacek, and Jurjovec, 2003; Nordstrom and Southam, 1997; Schippers, 2004) and low-cost (Schippers et al., 2010) method to extract minerals in many countries around the globe. For example, aerobic Fe(II)- and sulphur-oxidizing bacteria have been shown to be up to two orders of magnitude more efficient in the oxidation of pyrite than the chemical processes (Blowes, Ptacek, and Jurjovec, 2003; Nordstrom and Southam, 1997; Schippers, 2004). Additionally, bioleaching can be used to extract minerals from low-grade ores, sulphidic waste rock dumps, and tailings efficiently (Schippers et al., 2010)."

Jan 1, 2017

By Max Roseler

THE CHAIRMAN (WILLIAM KELLY, Vulcan, Mich.).-Some 8 or 9 years ago I was at Daiquiri, only a. few miles east of Firmeza, where there are deposits of iron ore of the same general character. There is a great conical hill, perhaps 800 or 1,000 ft. in height and the ore deposit appears to be somewhat in a canoe shape on one side of the hill. The mining has been done by quarrying the ore in benches. These are called levels and to go to the 10th level it was necessary to take mules and ride to the top of the hill, which was to me an upside down arrangement of numbering levels and a novel method of entering and viewing a mine. A little copper ore can be seen in places, and not being a geologist I thought the deposit might possibly be a gossan, but none of the geologists who have written on the subject approve of this hypothesis and the great question seems to be what part, if any, the limestones have played in the origin of ore; whether these deposits are replacements of limestone and whether they are contact ,deposits between the limestone and the other rocks. Examinations have been made by many eminent geologists and the problem has been discussed vigorously on both sides. The deposits are exceedingly interesting from a commercial standpoint and although they have been studied for a number off years the origin of the ore is still a difficult and somewhat controversial question. J. T. SINGEWALD, JR., Baltimore, Md.-I have had the privilege of visiting these deposits and have been very much interested in this paper, of Dr. Roesler's; having been on the ground, I can easily appreciate the difficulties under which he labored in attempting to work out the geology of that region, and he certainly deserves considerable credit for the way in which he has deciphered the geological relations of the Firmeza district. There are several points in his paper 1 ,would like to discuss; first, in regard to the geological interpretations. His differs from previous interpretations in the relative age of the diorite and the granite, but you will note that Prof. Lindgren suggests the probability. that those two rocks are very closely of the same age, and Prof. Kemp actually suggests, although he does not-accept the idea, that the granite is probably later than the diorite, so that there seems to be no particular reason

Jan 4, 1917

By Walter Harvey Weed

The notes given in this paper, the result of observations made during recent brief professional trips to the northern States of Mexico, are offered as a slight contribution to the geological knowledge of a region little known, but long famous for its rich gold- and silver-mines. They are not detailed geological studies, but they contain, I believe, the salient facts. The following districts were visited: 1. Santa Eulalia (silverlead) ; 2. Parral (silver-lead); 3. Las Vigas (copper); 4. Jimenez (copper); 5. Guadalupe y Calvo (gold); 6. La Cumbre (gold); 7. Palmarito (silver); 8. Cananea (copper); 9. Sierra Pinitos (gold); 10. Sierra Azul (gold). 1. The Santa Eulalia Silver-Lead Deposits. Seventeen miles SE. of Chihuahua is the mining district of Santa Eulalia, to which that city owes its origin and long prosperity. Discovered in 1703, this district has been, and still is, one of the great silver-lead producers of the world. For 86 years after its discovery, the total output upon which the crown tax was paid amounted to $112,000,000. Worked until within the last 20 years by the most primitive methods, without machinery of any kind, the deposits continued to yield a vast treasure of silver; at present the yearly tonnage far exceeds that of former times. A broad-gauge road runs from Chihuahua up the valley of a small creek to the village of Santa Eulalia, which is situated within the borders of the mountains of that name. A few miles out of Chihuahua a narrow-gauge railway, owned by the Chihuahua Mining Co., branches off to the mines. This road ascends a smooth but steeply-rising plain to the base of the mountains, and winds about the slopes until the mines are

Jan 1, 1902

By Joseph J. Yancik

In Moscow, the delegation received a briefing on the Soviet coal industry from First Deputy Minister Vladimir Fedanov. A similar briefing was given to us on the Donets coal basin by Deputy Minister S. Saratikyanz of the Ukrainian Coal Ministry. Lengthy technical discussions were held with the mines staff and research personnel at the institutes we visited. In addition, we had detailed discussions with key staff members of two combinats; Donetskugol and Tulaugol. In all these meetings, principal topics were matters of safety related to hazards associated with face mechanization, coal transport, methane gas control measures, gas outbursts, coal and rock outbursts, fire fighting and control, explosion suppression and control measures, and other related hazard factors. There was also much discussion on miner training, miners' attitudes toward safety and accident prevention practices, and preparation and enforcement of safety rules and regulations. It would be helpful to briefly review Soviet coal production statistics for comparison purposes with the U.S., and for the purpose of referencing some of the delegation findings mentioned in this report. For an excellent, comprehensive picture of Soviet coal production and other related fuel statistics, the reader is referred to Strishkov's, et d. report.1 Strishkov's estimates agree with the numbers given us by Coal Ministry officials except in clean coal tonnage. The figures of 604 million mt of clean coal out of a total production of 655 tons raw coal in 1972 is much higher than Strishkov's estimate of 375 million mt clean coal.

Jan 7, 1974

By H. Hitchen

THE PURPOSE of this paper is to indicate the working capacity of different types of ropes for various engineering and mining duties. ROPE CONSTRUCTIONS There are approximately one hundred different designs of ropes in use today but, normally, only about ten are necessary for mining and engineering duties. The rest are designed for unusual equipments, or are different ways of combining wires of special shapes. Basically, the various designs of mining ropes consist of round, triangular, and oval strands, constructed with one or several layers of wire over a single wire, or a compound construction of sever.al wires. To suit different installations ropes are made with 3, 4, 5, or more of these types of strands over a central core, the ?co re itself being manufactured from either a fibrous material or a combination of steel wires. Nevertheless, in mining, the demand for 'locked coil rope', wl1ich may be considered as a single strand, is steadily increasing, especially for use on vertical shaft winding engines. So far as the locked coil rope is concerned, many constructions have been developed to suit different requirements, such as - in addition to winding ropes - aerial carrying Topes, shaft guide ropes and haulage ropes.

Jan 1, 1957

By 000-900-009-492

The flotation has been and is still the most widely used mineral concentration method. Because of its complexity, the flotation process required the development of robust control strategies which was facilitated by the introduction of on-line sensing instruments such as x-ray fluorescence (XRF) on stream analyzer (OSA), gamma density gauges and electromagnetic flowmeters. The interest in developing control strategies has persisted because the benefits to be gained in terms of improved metallurgical performance are substantial. As the flotation control becomes more and more difficult due to the emergence of low grade and complex ore cases, other control strategies have to be introduced. Froth based control is one of the emerging useful control strategy This paper will focus on the state of the art in the on-line froth characterization as obtained by numerical image analysis. The technology of machine vision provides a novel solution to several of the problems encountered in conventional flotation systems for monitoring and control, and constitutes a powerful tool for the investigation and interpretation of the effect of various flotation parameters as driven for the froth phases. Copyright @2001CIM

May 1, 2001

By F. C. Miller

The Colorado Fuel and Iron Company has divided their coal mines into groups or divisions: Las Animas, Huerfano, Fremont and Gunnison counties. Each division is represented by a safety committee composed of three men appointed by the management and three men selected by the employes? representatives. The three men appointed by the management are usually from a group engaged in routine work that is primarily of a safety nature. Mr. Robert McAllister, chief mine inspector; Mr. George B. Parker, superintendent of first aid and mine rescue training; Mr. F. C. Miller, chief chemist, fuel department; and Mr. 0. C. Irwin, assistant chief electrician. The three men appointed by the management act in each of the four divisions. It is the duty of the safety commit- tee to visit each mine three times per year and make a thorough investigation of conditions underground and on top. Their report is in the form of recommendations to the management for their consideration. They are also called to investigate all fatal accidents and learn, if possible, the cause leading up to the accident and recommend precautionary measures that will prevent the recurrence. This committee inspects the haulage roads, air courses, manways, electrical equipment, ventilation, timbering, working places and humidity. In addition, each mine has a local safety committee with the superintendent acting as chairman. It is the duty of this committee to keep in daily touch with conditions underground and on top. They hold weekly meetings and discuss problems related to safety. These men work on local conditions that govern their affairs. As an example: One of the mines has a checking out board at the man-trip parting in addition to the regular checking in and out system as required by law, and this board is checked before the man-trip leaves for the outside, giving the officials a chance to take prompt action in looking up a man who may have become ill or injured. Should a man walk out and forget to check off, there is a penalty imposed. The ventilation of a coal mine is most important and the method of conducting the air to the working face is one of the greatest precautionary measures linked with safety. A quantity of air must be maintained at every working face to insure rapid diffusion of explosive or noxious gases and in a manner without interruption. With this intent in, view, the Colorado Fuel and Iron Company is installing fan equipments with capacities of 200,000 cubic feet per minute with dual drives, twin fans in some instances, for insured circulation. Dual drives consist of a steam engine using exhaust

Jan 1, 1925

By D. Hu, L. Matzar, J. Hampton, M. Gutierrez

Nanodarcy permeability is common in many oil- and gas-bearing formations requiring unconventional stimulation technologies, such as hydraulic fracturing (HF), which can connect the isolated hydrocarbon-rich pores with a wellbore through induced fracture networks. Even though a dense induced fracture network is capable of accessing economic amounts of hydrocarbons, much of the rock between and very close to the fracture network is still un-accessed and contains extremely low permeability. Inducing fracture networks into brittle rock can create large amounts of micro failures in surrounding regions that are not connected to the wellbore, as can be seen in Fig. 1(a) from the very wide acoustic emissions (AEs) cloud associated with a narrow fracture generation. It is possible in certain types of rock to increase the effective matrix permeability in localized regions based on the damage associated with the surrounding hydraulic fractures and subsequent high stress concentrations along localized pre-existing potential failure zones. To study this problem, laboratory HF tests were performed at true-triaxial stress state in brittle crystalline rock while monitoring AEs. The AE associated with HF was analyzed for source parameters using the moment tensor inversion method called Simplified Green’s Functions for Moment Tensor Analysis (SiGMA). Using the moment tensor for each individual AE event, the mode of failure was determined. Crack slip directions and crack face normal directions were also found, along with the relative volume of individual micro failures as well as a damage parameter. The associated source parameters were used to classify differing regions of damage in the sample induced from HF and correlate these regions of differing damage to the effective drainage region. Shown in Fig. 1(b) is a near-wellbore (NWB) region that contained three times larger average relative volumetric deformation of individual tensile AE events than the average tensile AE event volume from the entire sample. Because of the large difference in micro fracture volumetric deformation for the NWB region compared to the entire sample, predictions of HF induced damage must be included in reservoir drainage predictions.

Jan 1, 2015

By Summers D. A.

A mining machine has been designed and fabricated to mine coal from room and pillar operations combining high pressure waterjet cutting and mechanical fragmentation. Waterjets are used to slot the coal face with an advancing plow wedge then breaking out larger coal pieces. The machine has the following advantages: - simply built around a disassembled longwall chock and gathering arm loader apron; - few moving parts which are simply and inexpensively maintained; provides immediate roof support in the face working area; - coal produced is larger, with resulting lower preparation cost; - no dust is generated; - risk of spark generation is virtually eliminated.

Jan 1, 1992

ALEXANDER, JOHN S, M,'74-6,'81-3 ASHBURNER, C A, M, '85-7 ASMUS, GEORGE, Dl, '78-80 BACON, D H , M, '00-2 BAYLES, JAMES C , M,'80-2,'91-3 P, '84-5, V,'88-9 BIRKINBINE, JOHN, M, '83-5, V, 'S7-J, P, '91-2 BLAIR, THOMAS S , M, '74-43 BLAKE, WILLIAM P , V,'71-4,'76-7,'05-6 BLANDY, JOHN F, V,'71-3,'78-9 BLOW, A A, C, '05-7 BOWIE, A J , JR, V,'93-4 BRAMWELL, J H , A1, '89-91 BROOKS, THOS B , M, '72 BRUNTON, D W , V, 97-8 BUCK, STUART M , M, '83-5 BURDEN, JAMES A, V,'80-1 BURNHAM, WILLIAM, M, '82-4. CAMPBELL, H H, M, '93-5 CHAMBERLAIN, H S , V, '96-7 CHANNING, J PARKE, V,'08 CHRISTY, S B , V. '91-2, '07-8 CHURCH, JOHN A, M, '79-8l,'94-6, V, '07-8 COGSWELL, W B, V, '74-5,'86-7

Jan 1, 1910

By Paul H. Johnson

Chemical mining may be defined as the in-place extraction of metal values from ores located within the confines of a mine (that is, broken or fractured ore, stope fill, caved material, or ores in permeable zones) or ores located in dumps, prepared ore heaps, or tailing ponds. The term solution mining has, in general, been used to mean the in-place dissolution of water-soluble mineral salts with leach solutions. Chemical mining is presently in its embryonic stage. Basic research needs to be done to understand the influence of physical and chemical factors in chemical mining, and applied research needs to be done on both a small and a large scale to develop practical techniques of field practice. The areas of research include the following: (1) Leaching chemistry, the influence of physical, chemical, and biological factors in in-place leaching (2) Hydrodynamics of chemical mining systems (3) The development of new, as well as old, leaching agents for use under chemical mining leach conditions (4) The development of new means of contacting fine and coarse materials (with solutions) under static leach conditions (5) The development of new processes for generating and regenerating chemical mining leach solutions (6) The development of metal recovery processes

Jan 1, 1969

By H. E. Nold

THIS paper is an effort to explain in a simple manner the fundamental principles involved in examining a clay deposit for both quantity and quality and in operating a clay mine, either open-pit or underground, so that the best quality of finished material can be made from the raw material available. The writer is aware that what is recommended in this paper is everyday practice in many refractories plants and in some other heavy-clay products plants, but observations made while visiting practically every clay mine in Ohio have convinced him that the practices herein discussed are not as widely used as their importance warrants. It is true that the problem of mining for quality is more acute in refractories plants than in most heavy-clay products plants, yet some of the latter are finding it profitable to pay more than ordinary attention to the selection and blending of their raw materials. It is hoped that this short paper may prove helpful to some who are now finding it difficult to produce a uniform product of as high quality as their clay deposit seems to warrant. The coordination of the work of the clay mine or pit with the manufacturing plant, to the end that the best product possible be made from the raw material available, presupposes a rather intimate knowledge of the clay deposit. The knowledge must include not only information of the amount of clay-available but also rather detailed information about both vertical and horizontal variations in quality of the clay. This information should cover three things: quality, quantity, and location.

Jan 1, 1929

By Ernest R. Lilley

While American scientific literature contains much information upon geologic conditions controlling the production of oil in Rumania, copper in Chile, and other fuel and metallic resources in many foreign countries, it is singularly lacking in data about the nonmetallics outside of the United States. Thus, though the United States is the outstanding market for European high-quality refined kaolin, and for the chinaware, porcelain, and other products of the European ceramics industries, American literature contains only the briefest references to the deposits from which the raw kaolin utilized is obtained. To the writer, to whom has come in the past year the opportunity of visiting a number of these deposits personally, they have proved of extreme interest both commercially and geologically. It is the latter phase that is discussed in this paper. The older and now largely crystalline rock areas of France, Germany, and other parts of western Europe contain numerous pegmatite dikes of which the upper portions have been subjected to surface weathering and kaolinization in much the same way as those of the eastern portion of the United States. Like the latter, the European pegmatite kaolins have long been known for their freedom from iron and other impurities offensive to the china and porcelain manufacturer. Unfortunately, they are also, like the American deposits, individually of small size and noted for their high costs of production. Deposits of sedimentary clay similar in many respects to the high-quality sedimentary kaolins of Georgia and South Carolina are known and worked, notably in southern Germany and in the Newton Abbott district of Devon and Dorset in England. In general, their relationship to the parent rock from which they were derived is more evident than in the United States and the individual deposits are of smaller areal extent and less regular in outline. While these deposits are of considerable economic importance they did not, because of their similarity to deposits in America, attract and hold the interest of the writer to the extent that several other types of deposits did. It is to the latter, which are so different from the kaolin

Jan 1, 1932

By J. H. Rowland, R. A. Thomas, III, C. D. Litton

Atmospheric monitoring systems (AMS) are required when using air from conveyor belt entries to ventilate working sections in U.S. underground coal mines. AMS technology has the potential to increase fire safety mine-wide, but research is needed to determine the detection and response times for fires of a variety of combustible materials. To evaluate the potential of an AMS for fire detection in other areas of a coal mine, a series of full-scale fire experiments were conducted to determine detection and response times from fires of different combustible materials that are found in U.S. underground coal mines, including high- and low-volatility coals, conveyor belts, brattice materials, different types of wood, diesel fuel, and a foam sealant. These experiments were conducted in the Safety Research Coal Mine (SRCM) of the U.S. National Institute for Occupational Safety and Health (NIOSH) located in Pittsburgh, PA, using a commercially available AMS that is typical of current technology. The results showed that through proper selection of sensors and their locations, a mine-wide AMS can provide sufficient early fire warning times and improve the health and safety of miners.

Jan 1, 2016

By K. K. Kohli, S. S. Peng, R. E. Thill

Introduction Since the adoption of the Surface Mining Reclamation and Control Act of 1977, which mandates that surface subsidence be an intergral part of the underground coal mine design, there has been a sudden rise of demand on guidelines for minimizing surface subsidence and its associated structural damages. Unfortunately there is no sufficient amount of systematic subsidence data to fill such a gap, although considerable research has been devoted to the subsidence induced damages of surface structures in the past. However, it was said that many surface subsidence surveys have been performed and monitored by coal companies during the past twenty years, and that it will be a great source of information for subsidence engineering design if they can be collected and assembled together. An effort was therefore initiated in the Department of Mining Engineering, West Virginia University, under contract with the U. S. Bureau of Mines in December 1978 to contact each individual coal company in the Northern Appalachian Coal Field for any surface subsidence survey data. After 10 months' survey, the data collected include: 17 longwall panels and 2 room and pillar sections. The data in each panel and section cover the complete set of subsidence survey raw data, underground mine layout maps, surface topo maps, geological loggings showing the stratigraphic sequences and thickness of the overburden, and if available, locations and types of surface structures. On-site visits were followed to study the surface terraines and structures. Interviews were conducted with the owners of the surface structures in most cases about, if any, the history and characteristics of damages. Most subsidence surveys started with the first panel and ended with the second or sometimes, but rarely, the third panel. The first panel may be located in a virgin area but frequently it was adjacent to (on the tailentry side) a mined-out room and pillar section. It must be noted that all of the subsidence data is restricted only to the amount of vertical subsidence and that the horizontal displacement measurement was completely ignored. Primarily due to the fact that vertical subsidence is the most striking feature in a subsidence trough, which is mistakenly considered to be the only critical contributor to surface structural damages, and that a horizontal displacement survey is much more complicated and time-consuming.

Jan 1, 1981

By B. Qiu

The large surface ground movements induced by underground mining could threaten the safety of the pipelines laid across the subsidence-prone area. Existing analytical methods for the stress analysis of buried pipeline over mine subsidence area were based on the assumption of ?thin? pipeline, which limited their applicability. This paper presents the improved model with the capability to determine the stress distribution of the ?thick? pipeline. The pipe-soil interaction in this model was also updated to adapt various pipe soil contact conditions. In addition, the time-dependent effects of dynamic subsidence effects were also added to the model. A case of protecting a long section of a buried large-diameter pipeline over two longwall panels in a shallow mine is shown. The stress distribution along the pipeline is determined and the overstressed sections are identified. A partial uncovering plan was developed based on the predicted stress and complicated terrain at the site.

Aug 1, 2013