Search Documents

By N Pirouznia, F Rashidi Nejad, S Naraghi

Sungun Copper Mine, which is the second largest copper mining operation in Iran has a large tailings storage facility with a seepage control dam located downstream of the main dam. Surface and groundwater in surrounding area of the tailings storage facility has been monitored for ten years. This paper will discuss the results of the surface and groundwater monitoring and seepage control at the Sungun Copper Mine. The results of the study show that if the tailings storage facility influence the water quality of the rivers, this effect is not significant, so that the prevailing parameters of the measured parameters were within the permissible standard of drinking water in Iran.CITATION:Rashidi Nejad, F, Naraghi, S and Pirouznia, N, 2018. Surface and groundwater monitoring and seepage control at the Sungun Copper Mine, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 439–453 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By H. Tsuruta, A. Fujibayashi, I. Sumi, A. Murao, R. Murai

Injection of biomass into blast furnace as alternative reducing agent is so effective for the purpose of mitigation of carbon dioxide emissions from steel industries, because biomass is considered to be carbon neutral raw materials. Certain amount of Palm Kernel Shell (PKS) is abandoned after Palm oil extraction process. To use as a reducing agent of blast furnace, PKS was carbonized and classified by 100 mesh sieve. To examine the gasification behavior of PKS carbide under the blast furnace conditions, several combustion experiments were conducted using hot model experimental furnace. The experimental results showed that the gasification efficiency of PKS carbide increased as the quantity of volatile matter increased. This tendency is the almost the same for the pulverized coal, so carbide of PKS can be used at blast furnace at appropriate amount of volatile matter that can be controlled by carbonization condition. In addition, the pressure drop of the furnace tends to decrease because the amount of ash in PKS carbide may be smaller than that of pulverized coal. PKS carbide is a suitable reducing agent in that respect.

Jan 1, 2015

By S. L. May

The Bureau of Mines has developed several methods for extracting tantalum and columbium (niobium) and the rare-earth compounds from ores and concentrates. A cooperative agreement was made by the Bureau with Porter Bros. Corporation of Idaho to process 200 pounds of its euxenite concentrate by methods that had been developed at the Albany, Oreg., Metallurgy Research Center. The euxenite concentrate was processed to extract and purify the valuable metals by chlorination, solvent extraction, and hydrometallurgical techniques. Chlorination was used to convert the valuable constituents into chlorides and to partly separate them. Solvent extraction techniques were used to separate the tantalum from the columbium. The rare-earth and uranium compounds were purified by hydrometallurgical methods.

Jan 1, 1959

By P. D. Rao, D. E. Walsh

A pilot-scale study was performed to evaluate the potential for gravity concentration of gold from -13 mm (-1/2 in.) crushed ore from Ester Dome, AK. 9.04 t (9.94 st) of crushed ore were sampled and processed through a Pan-American jig-Wilfley table pilot plant. Plant products were sampled for assay and material balance calculations. Gold recovery through one stage of jigging and two stages of tabling was 17.4% at a concentration ratio of 615:1. Concentrate grade was 766.3 g/t (22.4 oz/st). The feed grade to the plant was calculated at 1.71 g/t (0.05 oz/st). Jig tailings, primary table tailings and secondary table tailings grades were 1.44 g/t (0.042 oz/st), 1.30 g/t (0.038 oz/st), and 5.47 g/t (0.16 oz/st, respectively. Significant coarse, free-milling gold values were shown to remain in the, jig tailings. Concentrate mineralogy is discussed.

Jan 1, 1992

By M. Scaggs, K. Phillips

"Coal Worker’s Pneumoconiosis (CWP) is an occupational lung disease caused by chronic exposure to respirable mine dust. After decades of steady decline, CWP incidence appears to be on the rise since the mid-1990s, particularly in some regions of Appalachia. Alarmingly, many of these cases have rapidly progressed to the most advanced form of CWP, referred to as Progressive Massive Fibrosis (PMF). Most of what is currently understood about respirable mine dust has been gleaned from routine regulatory monitoring, which tracks total mass concentration of respirable dust (mg/m3) and, less frequently, silica mass content. This paper focuses on the use of thermogravimetric analysis (TGA) as a way to provide basic characterization of the whole composition of the dust, allowing it to be classified into three mass fractions – coal, carbonate, and non-carbonate minerals. TGA was conducted on 59 dust samples collected by miners from eight coal mines in central Appalachia, and the results are discussed in terms of differences between mines, regions, and primary occupations. Consistent with prior results on area dust samples from some of the same mines, results of the personal samples generally show that the coal mass fraction of the dust is relatively low. Carbonate and non-carbonate minerals thus tend to make up the bulk of the dust mass, and vary across occupations and specific mines. INTRODUCTION After nearly four decades of decline, the prevalence of Coal Workers’ Pneumoconiosis (CWP, or “black lung”) in the US has been on the rise since the mid-1990s (Laney et al., 2014; Laney et al., 2010; Suarthana et al., 2011; Pollock et al., 2010; Antao et al., 2005; Blackley et al., 2016). Particularly alarming is the number of cases of progressive massive fibrosis (PMF), which is the most advanced form of the disease (Pollock et al., 2010; Antao et al., 2005; Blackley et al., 2016; Laney et al., 2017). A recent study by Laney et al. (2017) observed 192 US coal miners participating in the Coal Workers’ Health Surveillance Program (CWHSP) who had been diagnosed with PMF since 2000. Of the 163 (85%) that had a normal radiograph on file to use as a baseline, 27 (17%) of these individuals had progressed from a normal radiograph to PMF diagnosis in less than 10 years. Moreover, 162 (84%) of the individuals in that study worked in KY, WV or VA, and 169 (88%) had only ever mined underground. Blackley et al. (2016) also reported on a group of 60 PMF cases that were discovered by a single black lung clinic in eastern KY. Since seeking care at such clinics and participation in the CWHSP are voluntary, and could be influenced by a number of factors, these recent reports may well overestimate the degree of resurgence in severe disease (i.e., versus disease that was previously under-reported). Even so, they highlight a critical need to better understand the cause(s) of disease development and progression – such that effective interventions can be devised."

Jan 1, 2018

By H J. Dalstra

High-grade iron ore may be derived from banded iron formation (BIF) through four fundamentally different processes:1. syngenetic precipitation of chert free BIF,2. residual enrichment by removal of gangue minerals from BIF to form bedded (residual) ironore,3. mechanical erosion of iron oxide and chert from bedded iron ore or BIF and re-deposition andupgrading as detrital iron ore, and4. chemical removal of iron from BIF and precipitation elsewhere as a secondary (channel) irondeposit.Finally, the BIF itself may constitute iron ore if a high-grade concentrate utilised for pellets or sinters can be derived from it through mechanical (industrial) separation of iron oxide by means of crushing/milling and mineral separation.Historically, exploration for high-grade BIF hosted iron ores was focused on the residual (bedded) deposits and driven by supergene concepts. Exploration for detrital and channel type iron ores was mostly secondary to exploration for bedded deposits, but recently, a more focused exploration effort has led to the discovery of enormous moderate to low iron grade deposits in the Pilbara region of Western Australia. Exploration for high-grade iron ores using syngenetic concepts has been limited,but together with exploration using hypogene concepts offers the best hope of fi nding concealed deposits. Exploration for BIF sources suitable for concentrate ores commenced in the ‘old’ iron ore provinces after the high-grade resources were depleted and has only recently gained importance in Australian BIF provinces, mainly as a result of high iron ore prices in the last decade.

Jul 11, 2011

By A. J. Baer

"DEFINITION OF THE REGION AND ITS BOUNDARIESTHE EXPOSED PART OF THE GRENVILLE PROVINCE is the southeastern part of the Canadian Shield, characterized by crystalline rocks with K-Ar ages of about 1,000 million years. Its Canadian portion is bounded on the southwest by Georgian Bay •and by Paleozoic sediments south of a line passing through Orillia and Kingston, on the southeast by the St. Lawrence River valley and the north shore of the Gulf of the St. Lawrence, on the east by the coast of Labrador and on the northwest by the Grenville front, a linear tec-tonic feature that is a metamorphic transition zone and/or a fault. Rocks located to the southeast of the front have younger K-Ar radiom€tric ages than rocks located to the northwest of it.The region is formed of complexly deformed and highly metamorphosed crystalline rocks and in part differs from other areas of the Canadian Shield by the presence of large amounts of crystalline limestone and bodies of anorthosite."

Jan 1, 1970

By W. E. STOKES

A GENERAL extension and appreciation of the stereocartographic principle of precise mapmaking is evident. Under the stimulus of war, many radical improvements in aerial photography, and in airplane and motor con? struction are indicated for the future. A survey of advanced military designs points to the conclusion that the familiar radial motor is destined for oblivion under the impact of the inverted "V" type.' The latest German inverted "V" design of 1000 hp. is 68 in. long whereas British and American motors of the same power are 72 and 94 in. respectively, suggesting a horsepower-weight efficiency ratio in favor of the former. Application of the pressure cooling principle has made possible the development of in-line air? cooled engines which offer many advantages, such as small frontal area, unobstructed vision for the pilot, freedom from vibration because rotative speeds are not limited by fundamental unbalance of reciprocating parts, freedom from excessive bearing loads, and less weight per horsepower.

Jan 1, 1940

By Hendon G. W, Carr F, Jiang Y

A vast majority of the operating longwall sections use shield-type face supports to provide ground control in the United States. As a co-operative research program between the University of Alabama (UA) and Jim Walter Resources, Inc.(JWR), a joint research program is underway to study interaction of shields with surrounding rock masses. A series of analyses on the response of shields are performed using monitored data at a longwall face in a deep coal mine. In this paper, various effects of parameters, such as leg pressure, setting load, developing load, maximum loading rate, pressure in capsule, and convergence between canopy and base, are discussed and recommended as stability indices. A microcomputer program is being developed for instantaneous interpretation of the shield monitored data, and for giving warnings of potential problems. The preliminary results define the effects of the setting load, developing load, and rate of developing load or leg closure rate. The objective of the study is to understand the shield characteristics and their interaction with surrounding strata in real time, then develop a reliable program for maintaining longwall stability.

Jan 1, 1992

By Robert W. Metcalf

The feldspars are a series of related aluminum silicates containing varying proportions of potash, soda, rind lime; smaller amounts of other minerals arc likely to be present as impurities. They comprise three principal types: Potash spars, microline and orthoclase (KA12Si208); soda feldspar or albite (NaA1Si308); and soda-lime e (plagioclase) fellspars. The last-named is an intermediate group ranging from albite through oligoclase, andesine, labradorite, and bytownite to anorthite or line feldspar (CnA12Si2O8), Minor varieties are barium feldspar or celsian and a potash-barium feldspar. Perthite is a mixture of orthoclase end albite in alternate layers. Graphic granite or "corduroy spar" is an intergrowth of feldspar and quartz characteristically in the ratio of 3:1. Cornwall stone is a natural mixture of feldspar, quartz, end kaolinite imported in former years in sizable quantity from Cornwall, England. (A similar synthetic mixture, including some fluorspar, has been blended and marketed in the United States as "Carolina stone".)

Jan 1, 1941

By B. Sameti

Blast engineers have been taking advantage of image-based rock fragmentation analysis methods for the past 3 decades to estimate rock size distributions. These methods utilize a wide range of image segmentation techniques, from manual to fully-automated, to delineate the edges of rocks in images. Rock delineation results are then converted to physical rock sizes (and percentage passing curves) by scaling the image pixels to correspond to physical measurements. The size scaling process is critical for acquiring physical measurements, but specific to the limitations of different applications. This article starts by presenting a shovel bucket-based fragmentation analysis system, where scaling is done using the known width of the shovel bucket within the image. Next, it describes methods that use pictures captured by digital cameras with scaling reference objects in the view. Finally, the article presents a method that uses three-dimensional imaging to capture images without the need for scaling reference objects. A portable device which utilizes a three-dimensional imaging method is proposed, and compared with the other methods. The proposed solution combines the generated three-dimensional points with the delineated rock boundaries in the image to reconstruct the surface, and generate accurate rock size estimates and percentage passing rock size distributions. System operation is described and its accuracy and performance are discussed for various scenarios. It is shown that since the device does not require a physical object for scaling reference, it is free from the limitations of other methods, and can be applied for automatic rock size measurement from various sources such as mining shovels, loaders, crushers, stockpiles, haul truck beds, and conveyor belts.

Feb 23, 2014

By Chao Zhang, Wenhao Xia, Jianxin Fu, Ling Yu, Weidong Song, Yang Li

Sanshandao Gold Mine is the only undersea metal mine in China. To deal with the collapse and pumping of stopes and roadways caused by complex ore-rock occurrence conditions, the mine conducts filling and sealing of some areas, and the remaining ore reserves will be mined after treatment. Therefore, it is urgent to evaluate the stability of rock masses, fault fracture zones, and aquicludes during the secondary mining process. In this study, displacement and microseismic methods are employed to monitor rock deformation and fractures. Additionally, FLAC3D was used to simulate the process of secondary mining, reproducing the evolution of stress fields, displacement fields, seepage fields, and plastic zones at different mining stages. The combination of numerical simulation and on-site monitoring verification demonstrates that the deformation of surrounding rock presents a rapid growth at the initial stage of mining, followed by a gradual decrease in the growth rate, and finally tends to stabilize; the fracture zone area at the 151–159 exploration line on the − 320 m level (near the 7# and 8# stopes) exhibits poor stability, and monitoring measures should be strengthened; the deformation value of the aquiclude is less than the deformation value of I protection level in the Code for Design, the impact of secondary mining on the aquiclude is limited; fault and fracture zone deteriorate rock mass stability, and their impact is related to their spatial locations. Hanging wall fault has a more significant impact on the settlement of the aquiclude, while the footwall fracture zone has a greater impact on the development of the plastic zone.

Feb 21, 2024

By Liu Chun-Bao Sun, Hong-Jun, Wei Zhang, Tao Xu

SABC circuits have gained widespread attention within China, and are being gradually applied to many mines. However, the domestic knowledge of comminution process is still relatively basic, and the design and production management of the application of SABC technology lack guidance of scientific theories. This research project focuses on the Phase I SABC milling circuits of Wu Shan Porphyry copper mine. Targeting the design and operation problems of existing process and circuit, and without increased investment and alterations in equipment, the new technologies will combine ordinary crushing and grinding theories as theoretical guidance, and borrow JK Simulation Software (JKSimMet) for analysis in order to optimize the comminution process, efficiently allocate production output and energy consumption, eventually resulting in increased production and energy efficiency. Using JKSimMet Simulation Software, and combining theoretical optimizing and practical production techniques, as well as the on-site situation, the eventual SABC comminution process and circuit optimization plan is: increasing the grinding Ball charge from 8% to 10% v/v in the SAG mill; Setting the Ball charge in the Ball mill to 27% v/v and the maximum operating power draw to 5 800kW; replacing the HP Series crusher with a TRIO TC84 crusher, which is without a power controller, and adding a pebble bin. The final optimization result is: Maximum system processing capacity increased between 20%-26.7%, specific energy consumption reduced by more 2.0 kWh/t, creating an economic benefit of over 300 million RMB, thus achieving the goal of increased production, reduced energy consumption, and improved profitability.

Jan 1, 2014

By Guillermo Florez Pinedo

Si bien la explotación de los recursos minerales influye en el desarrollo económico nacional, es necesario revisar el significado de la minería en el aspecto social y económico en el Perú a través de un plan maestro de desarrollo minero. En este sentido, el presente texto describe la estructura de este programa minero donde se evalúa los objetivos permanentes, las medidas de corto y mediano plazo, los recursos humanos, economía, tiempo, la estrategia de implementación y la acción empresarial del Estado respecto al desarrollo prioritario de la riqueza minera.

Nov 20, 1978

By Harrison H. Roberts

A. We are aware that many who are in the audience have perhaps heard before some of the material which will be presented. Since our firm is more closely associated with the heavy construction industry our experience is more oriented in that direction. Notwithstanding this, the subject your program committee has asked us to present centers mainly in the earth-moving field. We find a common denominator between say, the stripping of a site to uncover an ore-body which will be developed by open-pit methods, and that of excavating & transporting materials for an embankment dam, airport or other project. Both are earth-moving problems and we offer for your consideration a means of determining the most favorable method, equipment selection and resultant cost. We do considerable studies involving rock excavation for tunnels, underground powerhouses, inclined and vertical shafts for penstocks, muck-removal, electrical cable & other related underground work. Hence, we believe we speak the same language.

Jan 1, 1972

By Gabriel S. Esterhuizen

The design of support for underground excavations is a complex process in which the interaction between supports and the rock mass must be evaluated. The strength reduction method (SRM) is useful because it provides a stability factor of the supported excavation that can easily be compared between support alternatives. The method is based on numerical model analysis where the stability factor is determined by reducing the rock mass strength until collapse is indicated in the model. This paper presents the results of validation studies that were conducted using the FLAC3D stress analysis software to compare SRMcalculated stability factors to the empirically based Coal Mine Roof Rating (CMRR) and the Analysis of Roof Bolt Systems (ARBS). The objective was to determine whether the SRM, with its basis in mechanics, would predict similar outcomes as the fundamentally different ARBS and CMRR methods with their basis in empirical observations. A total of 450 different scenarios were evaluated in which the geology, horizontal stress, depth of cover, entry width, support spacing, and support length were varied. The results showed that the SRM-calculated stability factors were able to satisfactorily capture both the ?weak bed? and ?strong bed? adjustments in the CMRR. The SRM results were found to be well correlated to the ARBS stability factors for the 450 cases considered. Further analysis showed that the SRM accurately captures the effect of bolt length, depth of cover, and entry width on the overall stability of an entry.

Jan 1, 2013

By A. Gene Collins

This report discusses some of the chemistry and geochemistry of cesium and rubidium. Knowledge of the cesium and rubidium content of oilfield waters aids in resolving the origin of waters and petroleum, exploring for petroleum and other valuable minerals, discovering water pollution sources, and augmenting the knowledge of geologic formations. The methods described in this report permit the detection of less than 0.01 mg/l of cesium and/or rubidium in a complex oilfield brine or water. Solvents possessing high-dielectric constants were evaluated for their ability to extract cesium and rubidium tetraphenylboron from oilfield waters and for their flame emission characteristics. Nitroethane was selected and used for the extraction and flame spectrophotometric determinations because it gave the highest sensitivity. Cesium 137 and rubidium 86 were used to determine the extraction efficiencies, which were about 87 percent and 58 percent respectively using a single 10 ml nitroethane extraction from a distilled water matrix. The standard deviation of the determination was 0.0008 mg for cesium and 0.0007 mg for rubidium in the 0.01 mg range.

Jan 1, 1965

Modern coal cleaning technologies have allowed coal preparation facilities to become quite efficient at removing sulfur compounds, waste rock and low grade coals from run of mine coal. Up to 50% of the raw mined coal stream may end up as refuse, particularly when the coal originates from longwall mining operations, or is high in partings, rock and impurities. The refuse materials vary from coarse materials removed by physical screening to very fine materials removed by floatation and density separation processes. Coal refuse piles are also known by a variety of other names including "waste dumps", "gob piles" and "slate dumps". The potential hazards of improperly reclaimed refuse include contamination of surface and groundwaters by acidic leachates and runoff, erosion and sedimentation into nearby watersheds, spontaneous combustion, disturbance of topsoil borrow areas, and damage from landslides should large slope failures occur. Many of these problems have been particularly acute for abandoned refuse piles, and modern regulations attempt to minimize the environmental impact of coal refuse disposal operations.

Jan 1, 1993

By A. L. de Vegt

For the past ten years Paques has been engaged in the development and installation of treatment systems based on biotechnological processes to remove sulfur compounds from water, air and gaseous streams. Metal and sulfate can be removed from mine waters using two biological steps: 1. Sulfate reducing bacteria convert sulfate to hydrogen sulfide (H2S). The H2S reacts with the dissolved metals to form insoluble metal sulfide precipitates. 2. Sulfide oxidizing bacteria convert excess H2S to elemental sulfur. Paques has designed and installed a groundwater treatment system for the Budelco zinc refinery in the Netherlands to remove metals and sulfate as described above. The system has been operating since May 1992 treating a flow of 5000 m /d. A pilot plant started operation in November 1995 at Kennecott's Bingham Canyon Utah copper mine to develop the processes for metal and sulfate removal from groundwater and selective copper recovery from leach water. The principle of the biotechnological methods, full scale experience, and an overview of the test program at the copper mine are presented.

Jan 1, 1997

By D. H. C. Wilton, W. A. Sears

"Abstract-The 682.8 ± 1.6 Ma Tickle Point Group consists mainly of rhyolite flows and tuffs with- in the Avalon Zone of the Appalachian Orogen in Newfoundland. Stratabound massive sulfide mineralization, consisting of pyrite, sphalerite, chalcopyrite and galena, occurs at the Winter Hill prospect, where a lower pyritic, Cu-rich zone and an upper Zn-Pb-rich zone are hosted by a carbonate-calc-silicate lens. At the Frenchman Head prospect, stringers of pyrite, minor sphalerite, chalcopyrite and rare galena are hosted by felsic volcanic rocks of the Tickle Point Group .Base metal ratios, metal zonations and the overall stratigraphic framework suggest that these sulfide occurrences represent volcanogenic massive to semi-massive sulfide mineralization (stringer type at Frenchman Head). As such these prospects represent the only known VMS occurrences within the Avalon Zone of Newfoundland. Pb isotope data indicate that galena from the Winter Hill prospect is less radiogenic and older than galena from Dunnage Zone occurrences, and suggest that the Winter Hill mineralization formed in an environment tectonically distinct (exotic) from the Dunnage Zone."

Jan 1, 1996