Search Documents

By Matthew T. Mowry

As the mining industry continues to hire young professionals to supplant the growing number of retirees, a well-developed engineering curriculum, coupled with practical, real-world training, can prepare mining engineering graduates to make meaningful contributions in the industry. Successful companies can be measured not only by their reserve base and annual production but also by their retention of mining engineering graduates with zero to five years of operational experience. My personal experience in the industry during the last five years has been varied and rewarding. The knowledge and experience I have gained have taught me valuable lessons that prepared me for my current role.

Nov 1, 2013

By M. Saghaeian, R. Hejazi, L. Hosseini

The specific surface area (Blain value) of iron ore concentrate entering the pelletizing plant is one of the characteristics most effective on the overall performance of the plant such as producing harder pellets, decreasing additives consumption, and decreasing energy consumption. Therefore, preparing the feed entering pelletizing plant is required. The iron concentrate entering Ardakan pelletizing plant located in Yazd province, Iran bears relatively low Blain value (approx. 1600 cm2/g) which necessitates one stage of regrinding so as to increase the Blain value to more than 1800 cm2/g. Studies were conducted and results showed that HPGR is the best regrinding equipment for increasing specific surface area. Conducting pilot plant tests on the concentrate sample revealed that specific throughput is 181 to 263 ts/hm3 and specific energy consumption is 1.6kWh to 2.2 kWh. Pilot tests also showed that one stage of grinding results in 407 cm2/g to 553 cm2/g increase in specific surface area. Based on these results, diameter of rolls, length of rolls, power consumption and grinding force were calculated to be 1.3 m, 0.9 m, 1276 kW and 13800 kN, respectively. Therefore, an HPGR with a roll diameter of 1.52 m, roll width of 1.1 m, power of 1660 kWh and a capacity of 500 t/h has been selected and implemented in Ardakan pelletizing plant. Industrial performance of HPGR and its effects on the plant study results show that limestone and bentonite consumption has reduced about 60% and 30%, respectively. Total Fe of the final pellet has increased from 65.5-65.7% to 66.2%. Cold compressive strength (CCS) and porosity of final pellets are approximately 292 kg/pl and 20.4, which are in the acceptable range.

Jan 1, 2014

"Replacing the century old rail tunnels that run beneath the Hudson River and carry about 200,000 passengers per day between New York to New Jersey has been a high priority for many years. But after Superstorm Sandy hit the east coast of the United States in 2012, the urgency to replace the tunnels increased dramatically. The Hudson Tunnels project is one of nine projects that make up the larger $30 billion Gateway Project. The Gateway Project has been called the most urgent infrastructure program in the country and the Hudson Tunnels is the most critical part of the project, as it will build a new rail tunnel under the Hudson River and rebuild the existing and deteriorating North River Tunnel that connects New York and New Jersey.“Superstorm Sandy proved the level of resiliency of the tunnels, which was not very good,” Amtrak deputy chief engineer structures James Richter told attendees of the George A. Fox Conference in New York City on Jan. 23. Age and corrosive salts deposited by flood waters from the storm in 2012 have affected interior concrete and copper wiring in the tunnels. “Since then, things have been deteriorating and getting less reliable.”Richter, along with Mohammed Nasim, senior director engineering design, both with Amtrak, spoke at the 2018 George A. Fox Conference where more than 350 tunneling and underground construction professionals attended the conference at the Graduate Center of the City University if New York to share insights about the complexities many of them face on daily basis.Under the theme of “Managing construction of complex underground projects: Strategies for tunneling in populated areas,” the one-day conference featured presentations from some of the top minds in the tunneling and underground construction industry. The presentations touched on everything from the highly technical challenges of constructing tunnels through changing geology while working beneath cities and rivers, to navigating the complex financial issues and contracts that come with the projects that have many stakeholders.All of those challenges, and more are part of the Hudson Tunnels project. It is one of the best examples of the full complexities of a complex tunnel project, with the added pressure of securing funding from state and federal government entities under an increasingly tight deadline."

Jan 3, 2018

Many mining companies aim to integrate sustainability principles into their new projects. There is an intention for improvement, but frequently this results in little more than 'business as usual' projects that retrospectively categorise controls for environmental and social risks as sustainability initiatives as part of a public relations exercise. The successful implementation of sustainability requires a change of mind-set and behaviours at an organisational and personal level. In addition, sustainability incorporates a very wide range of interests and technical disciplines. One of the key challenges is in understanding how and when to pull these diverse threads together within a project or organisational process. This paper will explore a number of themes: What does it mean to implement a project in accordance with sustainability principles? How far beyond 'business as usual' is it reasonable to go, and what is the business case for this? Why do the intentions for sustainability sometimes fail and how can we prevent this happening in future? People are instrumental in delivering sustainability; how do we embed sustainability thinking into their behaviours and decision-making? The approaches that have been taken to integrating sustainability in design; what has and has not worked and some of the barriers to integrating sustainability into design? The authors will discuss these themes drawing on case studies from URS' experience in integrating sustainability into large projects. The authors will discuss the need for: a strategic approach which provides a simple framework for tactical decision-making and the consequences of taking tactical decisions in the absence of this framework, alignment of the project team and promotion of a culture of innovation, a shift from a risk/compliance mentality to an opportunity identification mindset, and a systematic approach to integrating sustainability into project design processes.

Jun 1, 2010

By Erick Lino

Como parte del proceso extractivo de la minería, se generan materiales de desmonte que deben ser almacenados en topografías bruptas y planas dependiendo de la capacidad de almacenamiento que requiera el proyecto. La geometría y los taludes de estas estructuras deben ser diseñados tomando en cuenta las propiedades de resistencia del desmonte de mina. Por ello, el presente texto describe la importancia de la caracterización geotécnica de este material con el objetivo de diseñar el depósito de una unidad minera en condiciones estáticas y dinámica.

Feb 1, 2017

By C Beal

Proper understanding and management of production drilling in sublevel cave (SLC) mines is essential for meeting production targets and for avoiding inefficiencies that could lead to costly bottlenecks. In many SLC mine management models drilling is considered a derivative activity of firing and bogging. Its scheduling is considered to be implied in a firing schedule and given an arbitrary target completion, ‘several weeks’ or ‘a month’, ahead of production firing. Like development, drilling activities are most efficient when conducted separately from other production activities. Unlike development, however, it is not apparent during planning and feasibility how far in advance of firing drilling activities ought to be conducted. This paper presents a method of defining a minimum threshold of drilled stocks above which drilling, firing and bogging operations occur most efficiently. As an example, the drilling activities, procedures, and maintenance at Glencore Xstrata’s Ernest Henry Mine are presented, and the larger scale consequences of improvements to these areas are presented to illustrate their importance in the operation of an SLC mine.CITATION:Beal, C, 2014. Understanding the role of production drilling and drilled stocks in efficient operation of a sublevel cave mine, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 235–242 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

Deposit of Jinbaoshan platinum group metals (PGMs) ore ranks the second in Yunnan province, China. Study on process mineralogy shows that the grade of copper and nickel in the ore is just 0.16% and 0.20% respectively. Moreover, the impurities magnesium and iron and silicon are rich in the ore. The copper and nickel sulfides in the ore, especially the minerals of PGMs, are finely disseminated with the gangues like serpentine. Fine grinding is necessary, and high content of MgO in the concentrate is inevitable through traditional flotation technology on the basis of process mineralogy studies. Achievements on process mineralogy studies are applied to guide the flotation tests successfully. Progress on flotation has been made through comprehensive studies. Suitable grinding by two stages is required for the finely disseminated PGM sulphide ore to achieve the liberation of valuable minerals. Stage grinding and stage separation shall be conducted for a better recovery of valuable minerals. The oxidation state of mineral surface of sulphides has a profound effect on flotation of the ultra-fine sulphides, especially the pentlandite. The combined use of collectors enhances the selective collecting on the ultra-fine and low-grade valuable minerals, is of critical importance.

Jan 1, 2014

By Ted Klemetti, Gabriel Esterhuizen, John L. Ellenberger

"Advanced numerical models can be used to evaluate entry support systems in coal mines. However, these methods require specialized software and specialized skills to create the models and evaluate the results. Practicing support design engineers require a method to rapidly assess a proposed support system for a given geotechnical scenario. A prediction equation that can be used to assess roof support systems has been developed from the results of hundreds of FLAC3D analyses that were conducted during recent research. These models were validated against field cases and empirical design approaches and were found to adequately predict entry stability in coal mines. The understanding developed from the model outcomes was used to develop an equation to predict entry roof stability against large roof falls. Least-squares error analysis was conducted to find appropriate parameters for the nonlinear equation. The developed equation can be solved using spreadsheet software, allowing for rapid assessment of alternative support system performance in variable geological conditions. The performance of the prediction equation is evaluated against empirical design methods and against selected case histories of support practices at currently operating mines. Examples are presented that demonstrate the performance of the equation in variable geological settings. The stability factor (SF) prediction equation can be used as an assessment tool to assist in the design of coal mine roof support systems.IntroductionGround falls represent a significant proportion of injuries and fatalities in underground coal mines in the US. During 2013, ground falls were responsible for 4 of the 14 fatalities and 16.6 % of the 1,577 reportable lost-time injuries (MSHA, 2015). In addition, each year about 400 to 500 large roof falls are reported that can extend up to or above the bolted horizon. Large roof falls and associated ground fall hazards can be mitigated through improved support design.The research presented here particularly addresses the problem of large roof falls that extend more than 90 cm (3 ft) above the roof line of an entry and may extend above the bolted horizon. Smaller roof falls that fall out between supports or extend less than 90 cm (3 ft) above the roof line are excluded. These smaller roof falls can be controlled by appropriate surface support such as roof screen or other skin control methods. Also excluded are roof falls that are associated with an individual geological structure such as a slip of fault. Structure-related instabilities can be controlled by strategically locating individual roof bolts or other supports appropriate for the local situation."

Jan 1, 2015

By J Moffatt, T Payten, N Spooner, L Teixeira, L A. Balzan, G Wilkie, G Tsiminis

Fluorine is a penalty element due to its reactive nature. In acidic environments many fluorine minerals dissolve to form hydrofluoric acid (HF), changing processing conditions. When smelted HF can be released, causing negative effects to nearby people and the environment, as well as potentially damaging the smelter. Sale of ore with high fluorine levels elicit a financial penalty or are banned outright. Real-time sensors create the opportunity for instantaneous decisions on ore processing due to changing conditions. A fluorine sensor would allow rises in fluorine concentration in a processing stream to be flagged, and decisions on processing conditions or diversion to stockpile before processing could be undertaken. As fluorine is a light element, it is difficult to detect with in-field XRF devices and does not work well with PGNAA. There are currently no existing sensors to quantify the presence of fluorine in real-time, and thus decisions based on fluorine grade cannot be made at minute- or even hour-scales. Sensors designed to measure the presence of minerals that contain fluorine are a possible avenue to enable the real-time detection of this element. Mineral-based sensing may also give an added advantage of additional information about how the fluorine will react under different processing steps. The authors were given a grant under CRC ORE II (project number P1–005) to search for mineralspecific signatures suitable for real-time analysis. The work focused on novel regimes and applications of fluorescence as a means to detect specific minerals. The aim was to exploit fluorescence responses unique to minerals of interest in mining systems in order to produce sensors that address gaps in existing capability. After the successful discovery of signatures specific to two major fluorine minerals an additional grant (P1–014) was funded to develop the research into a prototype on-belt sensor, in partnership with Scantech International Pty Ltd. This paper details the development of a sensor package through multiple Technology Readiness Levels (TRLs) through collaboration with government/industry grant schemes, academics from university, and a sensor-focused Mining Equipment and Technology Services (METS) company. We give a brief description of the new sensor technique and provide a case study of multi-disciplinary collaboration.

Aug 24, 2022

By Toby Forney, Joshua Schoonover

In typical surface quarry operations, productivity and efficiency related to pit development begin with drilling and blasting efforts. By embedding technology within drilling and blasting operations, blast results can be tailored to benefit the quarry by driving continuous improvement of production. This technical paper will focus on the continuous improvement efforts at a cement limestone quarry in Maryland and how those efforts have impacted mining production, safety, and efficiency with the application of specific blasting technologies.

Feb 6, 2023

By B Murphy, N Strong, J Albrecht

Rio Tinto’s Argyle Diamond Mine has a history of underperformance with delivery of ore from the underground operation to the surface for processing with no real clarity in sources of loss and value. In order to increase underground production performance, the basic concepts of the Theory of Constraints model were applied to the Argyle underground production system. This prompted a revised view on bottlenecks and contributors to value loss and ultimately leading to record breaking mine performance. System loss reporting to demonstrate the best opportunity to drive value, departmental detail to develop tools to identify improvement opportunities and clarity across the team to ensure alignment and clear lines of communication were critical to the project success.

Mar 15, 2021

Much of the theory upon which the Sublevel Caving (SLC) method is based was developed in Scandinavia many years ago. It was based mainly on æbinÆ theory and æellipsoid of drawÆ configurations derived from sandbox models. In many cases, classical SLC layouts influenced by these early theories obtained relatively poor results. Early dilution entry, low tonnage factors and low recoveries were commonly experienced. SLC soon gained the reputation of being a high dilution, low recovery and development intensive method. This led to SLC falling into disfavour generally, other than as a pillar reclamation method used at the end of the life of mines. More recently a number of mines, notably those in Australia, have adopted SLC as a primary extraction method and have achieved good recovery results. The reason for the better results is believed to be an outcome of modifications in some of the basic design parameters and operational procedures. This has led to questions being raised regarding the original æbin theoryÆ assumptions and classical SLC layout designs. It is clear that the fragmentation and flow characteristics occurring in a choke blast situation (compaction of waste, variable size and shape of fragmentation throughout the ring) conflicts significantly with the assumptions of regular loose flow of uniform, fine grained, material in a bin. Interactive versus independent draw conditions can also materially effect the outcome of a SLC operation. The good results obtained more recently can only be explained by using ænewÆ models of behaviour, which have to a large extent been borrowed from block caving. If these models are correct, they point to a number of design and operational changes that can be applied to improve the effectiveness of SLC. This paper discusses the factors that may not have been fully considered in early SLC design and modelling. It emphasises the importance of delayed dilution entry as a primary objective of sound SLC design and provides a basis for efficient SLC design and operation.

Jan 1, 2000

By Erik Klohn

The El Soldado copper deposit occurs in volcanic rocks of alkaline affinity of Lower Cretaceous age. The orebodies are discordant and show strong structural and lithological control. The mineralizing event was accompanied by hydro- thermal alteration expressed as carbonatization, silicification, and chloritization. Individual orebodies contain bornite-chalcopyrite cores which are surrounded by haloes dominated by chalcopyrite and pyrite respectively. The sulfur isotope composition of copper sulfides strongly suggests the sulfur is of magmatic origin. Fluid inclusion studies show the mineralizing fluid to be a highly saline NaC1-CaC12, brine. No evidence of boiling was found. The deposit is most likely of epigenetic origin. Hydrothermal fluids were produced during crystallization of a sodium rich trachytic magma during the waning stages of an episode of alkaline magmatic activity. Similar copper deposits along the Chilean Coastal Range may also be associated with alkaline host rocks.

Jan 1, 1986

S. F. Emmons, Washington, D. C.: Mr. Malcolmson's paper on the intensely interesting deposits of the Sierra Mojada creates a strong desire to visit the region so well described. Although it is difficult to intelligently discuss a locality that one has never seen, I cannot refrain from offering some remarks in the nature of a tentative suggestion: 1. Age of Beds.—Mr. Malcolmson speaks of the enormous thickness of limestone forming the Sierra Mojada as belonging to the Carboniferous series. If this is not a typographical error, it seems that he should present some evidence for such age, for Chism,* in his previous article on the district, says the only fossils found there were said to be Cretaceous; and it is well known by the investigations of R. T. Hill and others that the great thickness of limestone in this part of Mexico is of Cretaceous age. 2. Structure of Mountains.—Mr. Malcolmson presents good reasons for thinking that the structure of the two related mountain masses (Sierra Mojada and Sierra Planchada) is not the simple anticlinal fold given by Mr. Chism's section, it being evident that there has been faulting as well as flexure. I venture to add that the facts presented by Mr. Malcolmson seem to suggest the possibility that, instead of being simply an eroded anticline, the valley between the two ranges may have been formed, in part at least, by the irregular faulting down of the intermediate block, on the surface of which the volcanic breccia had originally accumulated at a higher level. The sections of the Exploradora and the San Josh mines, in the smooth surface of the contact, with clay selvages and the occasional slickensides, certainly suggest a structural fault between the limestone and breccia. The arrangement of some of the

Jan 1, 1902

By Donna Kliche, Charles Kliche

It has been previously documented that various weather conditions such as wind direction and speed, cloud cover and, especially, temperature inversions can significantly affect the overpressure generated by a blast event (Siskind et al, 1980; Oriard, 1999; Siskind, 2000). The overpressure can be magnified downwind and reduced upwind; a change in the regular profile of temperature with elevation can magnify or focus the sound intensity at some distance from the blast event.

Jan 1, 2011

By John J. Mahoney, George P. Demopoulos, Matthew T. Bohan

In recent times processing of arsenic-laden complex ores and heightened awareness of the detrimental health effects of arsenic has put an increasing burden on metallurgical operations to remove arsenic from processes for disposal in an environmentally stable form. At present, arsenic is removed and prepared for storage by precipitation of insoluble secondary arsenic-bearing minerals. It has been suggested that Ca(II)-Fe(III)-As(V) phases resembling the natural mineral yukonite, under certain conditions, may have a role in controlling arsenic pore water concentrations in arsenical waste storage facilities. In this study, a previous synthesis method of yukonite (Ca3Fe5(AsO4)4(OH)9⋅4H2O) is revisited and new solubility/stability data is presented based on a modified method.

Jan 1, 2014

By P Hogan, M Wells

Reflectance spectroscopy has become an established technique for mineral exploration and ore characterisation. However, there are few reported cases where the technique has been applied to the Hamersley Province channel iron deposits (CID). The Bonnie Creek CID, located ÿ140 km north of Newman in Western Australia, represents one of a number of CIDs recently discovered in the Hamersley Province. Reflectance spectroscopic analysis using the CSIRO HyLoggerÖ automated scanning system, in conjunction with X-ray diffraction and compositional analysis, was used to characterise and map the ore and gangue mineralogy in CID drill core. Using CSIROÆs spectral mineral characterisation scripts, it was possible to map the downhole distribution of the Fe-oxide abundance, hematite:goethite ratio and the gibbsite and kaolinite abundance. Spectral estimates of kaolinite abundance were found to be closely related to loss on ignition measurements at 650¦C and the spectral kaolinite abundance index provided a reliable estimate of the total weight percentage Al2O3 content. In addition, downhole HyLoggerÖ scanning of diamond drill core reliably mapped the distribution of kaolinite as supported by coincidentally elevated contents of alumina and silica. Furthermore, spectrally-derived estimates of iron oxide abundance were well related to assayed Fe wt per cent contents and use of the spectral iron oxide mineral index mapped the distribution of the goethite:hematite ratio, and demonstrated that material logged as high-grade ore in the Bonnie Creek CID was predominantly goethite-rich.CITATION:Wells, M and Hogan, P, 2013. Bonnie Creek channel iron deposits ore mineralogy - insights using the HyLoggerÖ technology, in Proceedings Iron Ore 2013 , pp 321-328 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By Manfred Hager

The ability of conveyor belts to transport large mass throughputs economically over previously unprepared ground has resulted in this system achieving great and extensive use. A significant component in this development is the conveyor belt itself. The development of high strength steel cord conveyor belts involves the optimising of splice design, the use of excellent rubber material especially in the splice, good craftsmanship during splice production and modern field vulcanisation equipment. The durability of a splice for belts of class St 3000 up to St 790 is expressed by the fatigue strength under dynamic stress. The results obtained with a test method and equipment developed by the University of Hannover indicate the present state of the art in this field. Belts of high nominal strength used on inclined long distance conveyors reach splice fatigue strengths of about 3000 N/mm. The design should only exploit approximately 50% of the fatigue strength determined in the tests as maximum operating stress. IMPORTANCE OF CONVEYOR BELT SYSTEMS The use of conveyor belt technology has expanded considerably over the last decades in the bulk goods transportation sector. Because of the favourable transport costs and the technology's adaptability to specific topographies, belt conveyors frequently represent the most economic solution. When flows of goods are large, as in German lignite mining operations, where masses of up to 40,000 t/h are given, it is the only technically feasible alternative. The use of belt conveyor systems allows the sensible distribution of the waste and the production of the coal (Hager, 1981). But this transportation alternative is also suitable when the masses involved are smaller. Whereas conveyor belts were only suitable for loose bulk goods up until a few years ago, today they are frequently also used for hard rock open cast mines, e.g. in the production of copper ore. Because of the favourable transport costs it is frequently still economic to use mobile crushers with a throughput of up to 10,000 t h 6 which breakdown the large blocks produced y explosives into transportable grain sizes. In many operations, trucks are only used to provide flexibility between the excavator and the crusher, i.e. over short routes, and the long, frequently steep, transport paths to the processing plant or to the spreader are undertaken by belt conveyors (Einenkel et al., 1992). The advantages of belt conveyors, i.e. to cope with large mass flows over inclines and down slopes of up to 1:4 have resulted in this system gaining very extensive use throughout the world. The conveyors can be installed over for the most part unprepared ground with suitable vertical radii, adapted to the locally available belt material. In the process individual conveyor belts with lengths of up to 15 km, and in the underground sector with lift heights of up to 1 km, have been built and operated. This great variety of application possibilities is complemented by a limited ability to pass through horizontal curves. This can be achieved with the help of design measures on the conveyor whilst bearing in mind the characteristics of the belt. STRESSING OF CONVEYOR BELTS IN DIFFERENT TYPES OF PLANT The advantage of conveyor belts compared with other systems is also to be found in the large available service-time window, i.e. the excellent reliability and the low costs of energy consumption and maintenance. It is in particular the reliability of a belt transport system which depends to a great degree on its main component, that is the belt - in all its different types and variations. For this reason, the belt is also given the greatest attention in the development of the individual components, because it is the belt which must be designed optimally with regard to various factors. The specific properties of the conveyor belt then assert a considerable influence on the design and sizing of most other components in a

Jan 1, 1993

By B. C. Tripathy, S. K. Padhy, R. K. Paramguru, Pinak Patnaik

"Cobalt is regarded as technology enabling metal among the less abundant metals found in the earth crust. Electrodeposition of the metal from aqueous sulphate solutions is the preferred technology for its commercial production. Certain additives are added in the electrolytic bath during electrodeposition for the production of uniform, smooth and bright deposits of cobalt metal with higher current efficiencies and lower energy consumptions. A detailed investigation has been carried out to determine the effect of additive Sodium octyl sulphate (SOS) on the electrodeposition of cobalt. The results indicated that the additive apart from increasing the current efficiency enhanced the quality of cobalt electrodeposits. A maximum current efficiency of 98.4% was achieved at 10 mg/L SOS. The presence of SOS in the electrolytic bath did not result in any noticeable change in the crystal orientation of the cobalt electrodeposits except at higher concentrations (50 g/L) of the additive. Scanning electron micrographs indicate that smooth, compact and uniform deposits of cobalt were obtained at 10 mg/L of the additive beyond which there is detoriation in the quality of deposits. Polarisation of the cathode was seen in the presence of SOS. The effect of SOS on the electro kinetic parameters: Tafel slope (b), transfer coefficient (a) and exchange current density (I0) has also been investigated.INTRODUCTIONCobalt is recognised to be a strategic metal among the various base metals, owing to its numerous applications in various industries. Cobalt as a metal finds its use in the preparation of rechargeable batteries, as an alloying component in the manufacture of space craft and jet engines, as a drying agent for paint varnishes, ground coats for porcelain enamels and in the manufacture of the catalysts for the petroleum and chemical industries (Davis, 2000). Although there is a huge demand of the metal the supply of the metal is limited due to its scarcity in the earth crust. The metal comprises of only 0.02% of the earth’s crust for which the metal is recovered from various ores of nickel and copper as a byproduct (Hawkins, 1998). The present day techniques for cobalt production includes mostly hydrometallurgical methods which are preferred over the earlier used pryometallurgcial methods carried out for the metal production. Almost 70% of the world’s cobalt produced currently is from hydrometallurgical techniques in which electrodeposition of the metal from aqueous solutions is the final step for metal production (Verney, 1988). The most preferred route for electrodeposition of cobalt metal involves a sulphate medium (Das and Subbaiah, 1984; Lenthall and Bryson, 1997; Sharma et al., 2005)."

Jan 1, 2016

By Irving Hartmann

Modern mechanized mining with high-speed machines, multiple-entry systems, multiple blasting, high-velocity air currents, and rapid haulage has brought many economic benefits and has on the whole enhanced safety in the coal-mining industry. It has, however, also introduced some added hazards, the control of which requires concerted effort and ingenuity. Mechanized mining has greatly increased the production and dissemination of fine coal seam or in mine entries. Use of high-speed machines has increased the probability of formation of incendive sparks, which are produced by frictional contact between moving metals and certain mineral substances in the coal seam or in the adjoining rock strata. In gassy seams rapid extraction of coal has increased the rate of gas evolution. These facts have made more urgent the need of preventing the ignition of coal dust and the development of widespread mine explosions. The ignition hazard can be controlled best by eliminating all potential igniting sources and by careful attention to ventilation designed to prevent accumulation of gas capable of triggering a coal-dust explosion. Frictional spark ignition by mining machines and suggested safeguards are discussed in a recent publication. Extensive research and long experience have shown conclusively that the propagation of coal-dust flames can be arrested and the development of widespread explosions prevented by properly applied, generalized rock dusting.

Jan 1, 1956