Search Documents

By R M. Smart, A T. Harrison

Backfill systems using unconventional cementitious binders have been successfully used in relatively deep and hard rock tabular mines for longwall, scattered stoping and shaft pillar removals. Two unconventional cementitious systems are discussed: A ground granulated blast furnace slag (GGBS) with an activator containing lime. This has been used with a total tailings æstableÆ slurry at a relatively low dosage of less than seven per cent, by mass, based on dry solids. The room and pillar stopes supported with this fill were up to 20 m high and the tailings were relatively high in pyrite. A GGBS binder plus a silicate based activator and gelling agent that virtually eliminated all water drainage (and hence post filling shrinkage). The system used a slurry, but the addition of the activator created a final placed product that had the behaviour of a paste. The system has been successfully used for almost ten years in the following applications: stoping widths (mining heights) above 1.6 m; and shaft pillar removals in seismically active areas at the end of the life of the shafts. This paper discusses the technical merits and costs of the systems and compares them to other fill systems (including true paste systems). the acceleration (normally g, 9.81m/sec2) is increased to a significantly larger (but generally unmeasured and unknown) value, as shown in Figure 1.

Jan 1, 1998

By J. Gogal

Cameco's Cigar Lake Operation (CLO) started commercial uranium ore production in 2015. Initial mining was focused in areas of the ore body with relatively low concentrations of elements of concern (EOCs). As mining progressed into areas of the ore body that were richer in EOCs, some statistically significant behavior of certain analytes was noted in the water treatment circuits. It was ultimately found that the CLO ore body natively hosts numerous alkyl arsine compounds in addition to inorganic arsenide minerals. The alkyl arsines were found to be recalcitrant to typical adsorption on ferrihydrite, with the degree of recalcitrance associated with the degree of alkylation. A number of changes to the process circuits and water balance were performed and planned in order to inhibit the transport of alkyl arsines from the ore stream into the process water stream, and to optimize the overall site water usage. In some instances, the interactions of equipment in conjoined circuits of the process had controlling effects on the behavior of the overall circuit. Work continues to iterate upon the capital design features in order to further tighten the water balance, and to optimize water usage and operating costs.

Jan 1, 2020

By W. L. Single

"LET ME FIRST OF ALL thank you for sending this invitation to me to participate in this Annual Meeting of The Mining Society of Nova Scotia. As an engineer, although I don't get an opportunity to practice very much engineering these days, I am, of course, always pleased to be able to meet with my fellow engineers to exchange views, but I must admit that today I feel a little bit out of place in the midst of all the experts that are here today. Let me make one thing clear - I'm a generalist! Your program states that I am to make a keynote address. I have always thought that a keynote speech is one that says something that has not been said before - announces some new program or policy, or says something startling. I am sure you will understand when I tell you that keynote addresses are made by politicians and that civil servants speaking publicly are usually expected to give an account of what is, or what is likely, to happen as a result of policies that have been announced in keynote speeches by politicians. I am reminded of a statement by a distinguished parliamentarian who said, ""However exalted a civil servant may be, he is not above the elected officials."" So today I will confine myself to giving you an overview with particular emphasis on the development side of oil and gas. The theme of ""Oil and Gas"" is a topical one these days. I suppose it's because of all the copy that is being generated by the media on the U.S. energy crisis, the Mid-East situation, the fact that most of the world's proven oil reserves are in Arab hands and, of course, the accelerated exploration activity that is taking place in the North Sea, in the Arctic, and off the coast of Newfoundland and Nova Scotia."

Jan 1, 1973

By E. B. Viljoen

I. R. M. Chaston* As a gravity concentration man in the midst of so many eminent flotation experts I feel like Daniel. However, I would respectifully disagree with the opening remarks by Mr Viljoen. First, he suggested that gravity concentration of cassiterite was not effective in sizes below 30 microns. In a paper to the Institution of Mining and Metallurgy in 19621, I gave some figures for gravity concentration of deslimed material both for cassiterite and for wolfram which indicated that careful shaking table concentration of fine deslimed material could give recoveries of 75 to 90 percent in the size ranges above 13 micron. These were figures obtained from normal plant operation. It would be interesting to know if any tests were carried out on gravity concentration of the efficiently deslimed feed to this flotation plant to see what the recovery would be. Secondly, Mr Viljoen suggested that gravity concentration plants were expensive. He gives the cost of a flotation plant at R300 000 to treat a feed of 400 t.p.d. to the desliming section or 160 t.p.d. to the flotation cells. From his operating cost figures it would appear that the flotation cost is approximately R2 to R4 per ton of feed to flotation and the total operating cost about R2 per ton of feed. A table plant to treat this tonnage of deslimed feed would consist of about 30 tables and should cost considerably less to install and very much less to operate than the flotation plant. Third, Mr. Viljoen suggests that the concentrate grade from a gravity concentration operation would be unacceptably low. The paper quoted abovel showed that once a primary fine concentrate had been made, giving a suitably deslimed material, further gravity concentration could give concentrates of over 40 per cent Sn with high recoveries. Tailing from this dressing stage was naturally returned to the feed. To give these high grades, sulphides had been removed by flotation but this necessary flotation step is simple and cheap to operate and could be restricted to the final stage when the quantities involved are small. I would agree that flotation has a part to play in fine tin recovery but this role would only seem to become fully effective at sizes below 10 micron and would seem to require, as Mr. Viljoen has suggested, a mechanism for sizing which is effective down to, say, 1 micron. In the meantime it would be interesting to try tabling the flotation tailing to see if it was possible to recover the plus 20 micron cassiterite which is not recovered well by flotation. One point which has been made during discussion is the suggestion that cassiterite particles have a fully hydrated surface at normal pH. I wonder if this layer could materially affect the overall specific gravity of a very small cassiterite particle and, if so, whether gravity concentration of the very fine cassiterite would be improved if carried out in acid conditions, which would inhibit the formation of this hydrated surface. REFERENCES 1. CHASTON, I. R. M. 'Gravity concentration of fine cassiterite'. Trans. Inst. Min. and Met. Vol. 71, p. 4, 1961 and 1962, and discussion of this paper. Dr. R. P. King Mr Viljoen has drawn attention to the difficulties associated with the presence of very fine particles in the flotation pulp and he has indicated that, on the Union Tin plant, they must sacrifice 30 percent of the cassiterite in the minus 7 /Lm material which they separate and lose. He has also indicated that the rate of flotation of cassiterite remained high at these small sizes. The problem arises because the very small particles stabilize the froth making it impossible to handle. These stable froths cannot be easily broken and therefore cannot be pumped and processed. It seems that further fundamental research work on the properties of stabilized froths is urgently required. We have found another difficulty associated with the presence of very fine particles in phoscorite slurries; these particles can be easily floated but with very poor selectivity. We believe that it is possible that a purely physical mechanism such as entrainment is responsible for the collection of fine particles in the froth. We have also demonstrated that the presence of fine particles in the pulp adversely affects the rate of flotation of the larger particles. For esample, we have found an increase in recovery of + 100 um material from 2 percent to 17 percent in a standard laboratory batch flotation test on phoscorite when the - 37 um was removed from the feed. Such interactions between particles are not universally recognised as an important aspect of the complex flotation mechanism. They should appear in any quantitative formulation of the flotation rate process.

By Raphael Calazans Cardoso

Os procedimentos de dimensionamento de juntas parafusadas devem corresponder adequadamente às condições impostas na prática, para garantir projetos de alta confiabilidade. Por isso, este estudo tem o objetivo de evoluir na compreensão do comportamento mecânico de juntas parafusadas submetidas à carga axial externa. Para tal foram realizadas simulações numéricas variando a pré-carga de aperto, o comprimento do parafuso, o atrito entre os componentes, a posição de aplicação da carga externa e os materiais dos membros apertados, de modo a verificar a parcela da carga externa transferida ao parafuso. Todos os fatores analisados alteram o comportamento mecânico da junta, exceto o atrito entre os componentes. A transmissão da carga ao parafuso se comporta de maneira não-linear pelo aumento da carga externa. Além disso, existe um patamar de carga externa abaixo do qual não há transferência de carga ao parafuso.

Oct 30, 2017

By Patrick E. Connell

During the ABM Conference of 2015 the latest design and process features of the new 3-roll RSB® generation were presented together with a unique Size Control System SCS® for a real time closed loop control to produce an extraordinary quality SBQ – day in, day out. In the past two years, Kocks has focused on improving the repeatability of the rolling process and developed technology to enhance the performance of its equipment. These developments include Fast Remote Control (FRC), Stands Adjustable Under Load (AUL) implementation of closed loop Size Control System (SCS), and finally a state of the art laser Gauge (4D Eagle) that pulls all of these developments into a complete package of quality. Gauges used in the past generally operated with the “shadow” measuring system. The latest gauge developments are based on the “light section” method. This method is more suitable to provide real time measurement parameters of the rolled bar. Placed close to the last rolling stand, the “light section” gauge is capable of measuring around the complete diameter with a clear definition of the bar stage in relation to the axes of the rolls. It is also capable of making these measurements using a very high measurement frequency. Following requirements of the market, requiring the highest gauge measuring frequencies which display the bar in the most accurate way even at the highest rolling speeds, the “4D Eagle” gauge was developed. This paper describes all the process features and parameters of this impressive and unique newly developed gauge as well as the other described technical improvements.

Oct 30, 2017

By Eugene T. Sheridan

The process of converting coal into coke is known as carbonization. Essentially, carbonization is destructive distillation in which the volatile matter of coal is released when coal is he ted above its decomposition temperature and passes through a plastic stage before solidifying and forming coke. The mechanics of coke formation are complex, and the specific properties of certain coals that tallow them to "cake" or form coke are still unknown. Coke is a hard, cellular, carbonaceous mass, formed by heating coal in the absence of air. It is porous, irregular in size and shape, and is similar in appearance to wood charcoal. Coke, however, is denser, more porous, and more abrasive than charcoal.

Jan 1, 1965

By Eugene T. Sheridan

The process of converting coal into coke is known as carbonization. Essentially, carbonization is destructive distillation in which the volatile matter of coal is released when coal is heated above its decomposition temperature and passes through a plastic stage before solidifying and forming coke. The mechanics of coke formation are complex, and the specific properties of certain coals that allow them to "cake" or form coke are still unknown. Coke is a hard, cellular, carbonaceous mass, formed by heating coal in the absence of air. It is porous, irregular in size and shape, and is similar in appearance to wood charcoal. Coke, however, is denser, more porous, and more abrasive than charcoal.

Jan 1, 1965

By Frank D. Lamb, Lloyg H. Baning

"The crushed-stone industry has long been troubled with the problem of producing a more or less cubical product for use as concrete aggregate. Its seriousness varies widely for each producer, depending upon the character of the rock employed for raw material and the ultimate use of the crushed stone. For many construction uses, such as the macadam or bituminous-concrete- type road, flat pieces are not objectionable and may even be preferable to more cubical rock. However, most specifications for concrete require that the stone must be reasonably free from flat and elongated pieces.The rigid specifications set by many contractors have resulted in the rejection of coarse aggregate that, except for the presence of an excessive amount of flat and elongated pieces, would be entirely acceptable. In many instances, if an efficient, economical method of removing flat and elongated pieces were available, local producers could meet the requirements of the contractor and thus eliminate the necessity for importing more cubical material.A brief investigation of the problem of removal of flat and elongated pieces from crushed aggregate, carried out at the Eastern Experiment Station of the Bureau of Mines, indicated that it is mechanically possible to remove flat pieces from crushed rock.TEST EQUIPMENTA number of mechanical devices are used by the coal industry for separating slate from coal; these depend upon the difference in shape of the crushed slate as compared with the coal. Such devices as shutter screens, spiral separators, and the Norman picker would be suitable for removing flat pieces from crushed rock in the same manner as they are used by the coal industry. None of these devices was immediately available for testing purposes, so an attempt was made to construct a simple device that could be used in commercial operations."

Sep 1, 1944

By L. Roux

This review was initially motivated by the author’s own experience in attempting to reconcile run-of mine production tons with the Coal Resource and Reserve estimation of mineable, in-situ tonnages. The primary scientific measurements and observations that are collected during exploration at the beginning of the value chain will have a profound effect on the future of the mining operation. Due diligence must be exercised during the planning of a new mine and during the life of an existing mine. The comments provided by the technical and economic assessment group of Venmyn Deloitte confirmed the need for this critical review. They found the reporting of Coal Resources in South Africa to be inconsistent. This was particularly problematic in the Waterberg Coalfield in Limpopo Province. In this coalfield there are two types of coal deposit present. The first is comprised of the thick intercalated, cyclic coal and shale/mudstone sequences of the Volksrust Formation. This overlies multiple coal seams within the Vryheid Formation, each of which is thick enough to be extracted as an individual raw coal unit. On the other hand, the interbedded coal and shale seams of the Volksrust Formation require beneficiation to separate the coal from the shale. The review examines practices and methods, investigates alternatives, provides checks and balances, and tests these against actual production reconciliations. In conclusion, the best estimates of the mineable, in-situ tonnage will be obtained from the air-dry raw material density. These estimates should be adjusted afterwards to allow for free moisture content. The adjustments are derived from reconciliation data. The greatest contributing factor to the over-estimation of Reserve tonnages is the moisture content of the raw material. This fluctuates significantly under varying conditions in situ, as well as upon exposure to the natural environment. The air-dried density of the raw material includes inherent (structurally bound) moisture within the matrix. It provides credible tonnage estimations of raw material available while also providing an indication of voids within the volume of material being assessed. The calculated solids percentage can be used to adjust the specific gravity, which is determined via the Archimedes principle. This will supply a representative estimate of the material to be mined.

Nov 1, 2021

By Simon J. McDonald

In late 2007 Neptune Minerals Plc. commissioned Genesis - a leading consultancy and engineering company affiliated to the Technip group - to undertake a Seafloor Mining Conceptual Study for mining of Seafloor Massive Sulphides (?SMS?) in Neptune?s New Zealand licenses. A key deliverable of the study was information to de-risk the perception of SMS mining for investors the minerals, and that deep-sea mining of SMS material is technically feasible, commercially viable and can safely be managed as a sustainable marine resource industry. The aim of the study, completed in April 2008, was to evaluate alternative existing marine technologies for seafloor mining, ore lifting, dewatering and surface offtake, considering the following parameters: ? Efficiency; ? Reliability; ? Safety; ? Environmental impact; and ? Cost

Jan 1, 2008

By K. Lang

The use of high-efficiency electrical submersible pumps (ESPs) for large scale, open pit mine dewatering operations provides a good example of how technology, products and services from the oil and gas industry can be adapted to the mining industry. In this case, the mine is Goldcorp?s Peñasquito in the Zacatecas state of Mexico, at the Peñasco and Chile Colorado open pit deposits. The technology, products and services are from Schlumberger artificial lift (AL) and Schlumberger industrial water services (IWS). Overview of high-efficiency ESPs This section provides a brief description of the basic components, specifications and operating capacity ranges for the ESPs compared with traditional or conventional dewatering well pumps. This information helps to establish how ESPs provide certain functional and economic advantages over conventional pumps in a mine dewatering application. A schematic of a high-efficiency ESP in an oil and gas (O&G) application is shown in Fig. 1.

Sep 1, 2013

By Sushil Bhandari, Amit Bhandari

In this paper, a case study is presented of a large global cement company using a cloud and mobile based platform across 17 of their mines consistently over a large number of users over a period of over two years. The use of a blast platform is detailed which include blast designs, blast data collection and the trends in terms of results.

Feb 1, 2020

By J. J. Shields

With the increased use of mechanized equipment in mining bituminous coal, production panels are mined out rapidly. To keep current with the rapid completion of production panels, development work must be speeded up also. Although the same type of equipment usually is employed in development as in production places in the same mine, past output per man for development usually was less than from production panels. A study of development practices in 14 mines reveals a tendency toward equalization of the output per man between development and production.

Jan 1, 1957

By I. A. Khabarova

The paper presents the results of experimental investigations of the effect by high-power nano-second electromagnetic pulses (HPEMP) on change of surface composition, physical-chemical and flotation properties of pyrrhotite, and search of optimal combination of flotation reactants providing increase of metal extraction from disseminated copper-nickel ores. Preliminary electropulse effect on products before flotation allows to create optimal conditions for flotation separation of pentlandite and pyrrhotite owing to forming the new phases and defects on the surface of sulphides. It was established, that the yield of monomineral fractions of pyrite, pyrrhotite and chalkopyrite increases by 5%~15 %, compared with flotation with one butyl xanthenes (BX), during usage of combination of thionic carbamate (isopropylmethylthionocarbamate (ITC) or isopropylethyl- thionocarbamate (Z-200) with butyl xanthate (BX). Sorption of investigated reactants and strength of their fixing on the surface of minerals are examined; it helped to reveal the cause of rise of floatability of sulphide minerals for the case of combination of reactants. Preliminary high-pulse processing and reactant conditions with usage of combination of thionic carbamate and xanthate have been tested on the sample of disseminated copper-nickel ore from Norilsk region.

Jan 1, 2014

By S Arnold

Properties of the soil profile fundamentally control water-limited ecosystems. Soil water availability affects vegetation dynamics of plant communities, but is also affected by these communities in return. Understanding this eco-hydrological interplay and the role of physical soil restoration is crucial for successful rehabilitation and management of post-mining landscapes in semi-arid areas. However, uncertainties exist in both the mathematical description of plant communities within ecological submodels and the predictability of future rainfall events. This study uses information gap decision theory combined with an ecohydrological system model to investigate how both uncertainties impact decision-making in the context of ecosystem rehabilitation. A range of management strategies are investigated to identify the optimal soil thickness for successful rehabilitation of native plant communities in Central Queensland. The results emphasise that thicker soils can counterbalance uncertainty in mathematical description of plant communities by increasing the simulated survival probability of plant communities. However, the influence of thicker soils on the robustness of plant communities against a change in future rainfall amount is rather marginal. By allocating an economic value for restoring a particular thickness of soil layer, these results can be used to evaluate the costs of ecosystem re-establishment with regard to two target measures - the survival probability of the plant community and their robustness against climate change.CITATION:Arnold, S, 2012. Finding optimal soil restoration strategies in the face of uncertain future rainfall amount, in Proceedings Life-of-Mine 2012 , pp 91-96 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By Marty Hudyma

Large seismic events have been reported in mines in the Sudbury mining camp for more than 70 years. Nevertheless, no detailed record of the events has been compiled. In 2008, the Sudbury Regional Seismic Network (SRSN) research project was initiated to collect more accurate data with regard to the magnitude and locations of mining-induced seismic events in and near the mines in the Sudbury Basin. The data is used to better understand the mechanisms of the events and cause-effect relations between mining and seismic events. Through the collection of a central database of large seismic events, new insight is being be gained into why some mines are much more prone to large events than others. Fifteen low cost seismic stations have been distributed throughout the Sudbury basin. The data from each seismic station is uploaded to a central server using the internet. Data recorded on the SRSN is processed on a daily basis, and a weekly summary of blasts and events is issued to project sponsors. Seismic events smaller than local magnitude +1.0 have been identified and located. Event location accuracy is less than 2 kilometres, however, many events have been located less than 1 km from a mine. The SRSN fills a seismic monitoring gap between the in-mine microseismic monitoring systems and the earthquake monitoring system operated by the Geological Survey of Canada. Since July 2008, more than 600 mine blasts and more than 450 mining-induced seismic events have been recorded in the Sudbury basin. This paper primarily discusses the technical aspects of the design and operation of the SRSN. The SRSN is a Canadian Mining Industry Research Organisation (CAMIRO) research project, with industry sponsorship and support from FNX Mining, Itasca Canada, Vale Inco and Xstrata Nickel.

Oct 1, 2010

By Baojie Zhang

The main goal of this study was not only to investigate the effectiveness of the FGX Dry Separator for removing pure rock from run-of-mine coal producing a better feed stock for conventional coal preparation plants but also to optimize the FGX Dry Separator performance for producing a salable clean coal product without using the conventional wet coal preparation processes. A Model FGX-1 Dry Separator with feed throughput capacity of 10 tph was extensively tested at the Illinois Coal Development Park using two coal samples having distinctly different cleaning characteristics. Statistically designed experimental programs were conducted to indentify critical process variables and optimize FGX Dry Separator performance by systematic adjustments of critical process variable parameters. The coal cleaning performance of the FGX Dry Separator was evaluated for the particle size range of 63.5 x 4.76 mm in most cases, although FGX Dry Separator feed consisted of nominal -63.5 mm run-of-mine coals. The best cleaning performance obtained from the FGX Dry Separator is described by specific gravity of separation (SG50) and probable error (Ep) values of 1.98 and 0.17, respectively. The SG50 and Ep values for individual size fractions were as follow: 1.90 and 0.12 for the +50.8 mm size fraction, 1.95 and 0.18 for the 50.8 x 25.4 mm size fraction, 2.01 and 0.19 for the 25.4 x 12.7 mm size fraction, and 2.03 and 0.23 for the 12.7 x 4.76 mm size fraction. These process efficiency measures produced a clean coal with ash content of 13.38% from a feed coal with ash content of 34.45%. Ash content of tailings and middlings streams were 85.09% and 39.57%, respectively. Total sulfur contents of corresponding streams were 3.87%, 4.68%, 6.87%, and 4.62%. For a relatively easy to clean Illinois No 6 seam coal (Cleaning Index: 0.72), only about 0.42% of the clean coal (i.e., 1.6 float fraction) present in the feed was lost to the tailings stream. For a relatively difficult to clean coal (Cleaning Index: 0.53), about 0.98% of the clean coal present in the feed was lost to the tailings stream.

Jan 1, 2012

By G Chitombo

Mass mining methods have become the mining industry’s preferred way of extracting most of the world’s most important metal and mineral commodities. Given the rapidly increasing global demand for commodities, the requirement to increase the contribution of some of these (eg copper and gold) from underground sources also continues to grow. In the case of copper this contribution is needed by a number of major producers to supplement production from their ageing deep open pits. Satisfying this increased demand will require the design, construction and operation of more effective, higher capacity and larger scale mines which, in turn, will require enhanced mass underground mining techniques such as block caving (BC), panel caving (PC) and sublevel caving (SLC).It is now widely accepted that future discoveries of orebodies, which will be developed using these methods, are almost certainly to be much deeper than the deposits presently being mined in this way and made more challenging because of the likelihood that the associated grades may be much lower than currently mined. The design and mining of future large-scale cave mines (supercaves) will become crucial in order to extract full value from such deposits. An essential prerequisite of this will be a much improved knowledge of the deposit, ie Total Deposit Knowledge. In this context, Total Deposit Knowledge is the characterisation of the ore deposit and its surrounds at all scales and includes; rock type (lithology), the spatial orientation of a range of geological features or discontinuities, rock mass fabric knowledge, metal grade and distribution data, geometallurgical data (including alteration), geo-hydrology, permeability and porosity. This is the information that will be used, as now, to delineate geological and geotechnical domains and construct models, but with outcomes superior to those presently available. From this information better-informed feasibility study design decisions and performance predictions must be made. In summary more geological information and analysis is required and this needs to be aligned to potential mining and processing requirements much earlier in the project than commonly occurs.

Aug 22, 2011

By W. A. Lang

"I.-IntroductionAn attempt bas been made in this paper to provide a basis for appraisal of the future of the coal briquetting industry in Alberta by outlining the processes used for briquetting various ranks of coal, by specifying the requirements of a briquetted fuel, by indicating .the status of the industry in the United States, by giving developments in Western Canada, by assessing costs of processing, and by discussing briquetting researches in progress. Much of .the detail bas been omitted since this might mask, rather than reveal, the more important phases of the problem. Reference will be made when possible to published articles where many of the details can be obtained.It should be stated at the outset that, in the writer’s opinion, there are three possible developments in Alberta as regards briquetting: (a) an expansion of the briquetting of the fines of • non-coking and coking coals of semi-anthracite, and of low and medium volatile bituminous rank; (b) the processing of the fines of high-volatile C bituminous coals; and (c) the upgrading of the lower rank high-moisture sub-bituminous coals. Details of the chemical and physical properties of these coals can be obtained in publications of the Research Council of Alberta (1, 2), and of the Fuel Research Station, Bureau of Mines, Ottawa (3).Semi-anthracite and low and medium volatile bituminons coals occur in the mountain areas of Alberta, where, during the upthrust of the Rocky mountains, the coal beds served as the sliding surface. This resulted in the coals being; crushed and consequently they contain a h1gh percentage of fines. In some cases they are high in mineral matter and require to be cleaned before being processed. However, the cleaning of fine coal is both difficult and costly. Both the amount of fines present in the mine-run coal and the amount of mineral matter associated with the coal have increased through the introduction of mechanized mining and through the recovery of coal by stripping operations."

Jan 1, 1950