Search Documents

Since the beginning of the computing age, technical software packages have not been developed to address only programming specialists but have been dedicated to process engineers. For process analysis, BRGM is developing and commercializing three packages: ? sampling software: ECHANT 2.0 for Windows ? material balance calculation: BILCO 2.0 for Windows ? steady-state simulator for plant design, adaptation and optimization: USIM PAC 2.1 for Windows This paper deals in a first part with the main features of these three packages. In a second part, advanced models are presented for SAG/ AG mills and flotation columns. An industrial case of application is shown for each of them.

Jan 1, 1997

By Charles Vaught, JON VOLKWEIN, ROBERT PETERS, ERICA HALL

Since 1999, the CWP level among miners with 25 years or more experience, for instance, has risen from slightly more than 4% to 9% (See Figure 1). While it is obviously necessary to protect all miners’ lungs, there is now a technology to improve the chances that new miners’ lungs will be protected from the day they begin work.

By Hermann Wotruba, Lars Weitkämper

"Dry coal dressing was popular during the 1950’s and 60’s in many parts of the world. The devices mainly used were air jigs and air tables.The increase in ash and moisture content of run-of-mine coals due to the wide advanced mechanisation of mining methods during and after this period led to that pneumatic devices being unable to treat run-of mine coals with the desired efficiency. Since the 1960’s almost all new coal preparation plants have been based on wet processes that are highly efficient in terms of coal recovery and their ability to handle damp and sticky run-of-mine coals. (Frankland, 1995)However, water is becoming increasingly costly and the disposal of fine products, containing most of the water, is an environmental concern. There would be significant cost savings and a lower total energy consumption if coal could be cleaned dry. Efficient dry coal treatment would be an interesting solution in desert, arid or cold areas.In Germany one dry coal dressing plant is in operation. This is the last operating dry coal dressing plant existing in Europe. The actual technical standard of dry coal dressing has been analysed during test-work and sampling in this plant (Saar Region in Germany). The process and the advantages and disadvantages are presented. The plants problems are low efficiency in the fine fraction –6 mm and the coarse fraction +30 mm and a low overall throughput as well as the lack of an automatic process control system. The separation results in the medium size fractions between +6 and -30 mm are excellent"

Jan 1, 2003

By M. Santillan

Minerales Monclova S.A. de C.V. (MIMOSA) has applied different methane gas drainage technologies, according to the top industry requirements in order to keep the methane gas at the lowest possible concentration in our operations, both in the development sections and longwall sections. Our staff has used the horizontal rotary technique. In 2004 MIMOSA bought a re-built drill machine and signed a contract with Resource Enterprises Inc. (REI), which included a training program in Horizontal Directional Drilling using the reflex system. The training system was developed for a period of three months in Mine VII, with very good performance by the MIMOSA staff. After the training the equipment was moved to Esmeralda Mine, where we had already drilled holes at the development section, 2,500 ft. It was the longest distance that could be reached with our original equipment, obviously; the directional drilling program is another challenge for us and our staff, but we are very confident that our result will be better every time. We will be evaluating each borehole and expect to improve our results in each progressive borehole, until we can drill up to the capacity of the equipment. We are in the process of buying another drill with an electronic monitoring device (DD DMecca) in the following months.

Jan 1, 2009

By J. R. Stone, J. T. Roy

ASARC09s continuous tapper for lead blast furnace is described. Its use throughout the company's plants has resulted in higher production rates, lower labor costs, and better working conditions. It has also permitted wide latitude in blast pressures, as well as in charge and slag compositions. The practice of tapping a lead blast furnace has remained essentially unchanged for many years. In principle, it is a batch operation discharging the products from the continuous smelting of lead-bearing materials. As such, it imposes certain restrictions on the proper functioning of the smelting operation. First, it calls for a highly developed sense of timing, and a considerable amount of physical effort on the part of the operator. Dirty and hot working conditions, as well as the hazards of flying metal and slag, usually prevail. These conditions have resulted in higher labor costs, both in rate and in amount. Labor turnover has also been high. Secondly, rigid control of mechanical and metallurgical factors must be maintained. Frequent oxygen lancing of the tap hole is needed to permit tapping, thereby increasing operating costs. Rapid increases in smelting rate, plugged tap holes, or forgetfulness on the part of the operator may permit the molten material to rise above the tuyeies and freeze the furnace. Also, the operator will often blow out the tap hole after draining, filling the area with fume. Composition of charge also vitally affects the tapping. The type of lead-bearing material being smelted will naturally affect the smelting rate, and thus the frequency of tapping. The amounts and types of fluxing materials, which determine the ultimate fluidity of the slag, must be regidly controlled. Finally, the batch tapping of a continuous smelting operation of this type appears to be wrong in principle. The molten material drains into the crucible at the bottom of the furnace where it starts cooling immediately and continues to cool until tapped out. While keeping the lead molten is no particular problem, maintaining a fluid slag at all times is often difficult, and sometimes impossible. These factors all point to the desirability of a method for the continuous tapping of a lead blast furnace. The expected advantages would be more desirable working conditions, lower labor costs, increased production, and a much wider latitude in both blast pressure and charge composition. CONTINUOUS TAPPING Historical. A number of devices, e.g., mechanical tappers, siphons, and lead wells, have been tried in the past in attempting to effect continuous tapping. None proved to be entirely satisfactory for tapping lead and slag simultaneously. It was not until 1955, however, that ASARCO designed and put into operation a successful tapping unit at its East Helena, Mont. lead smelter. This unit is described in detail in U.S. Patent NO. 2,890,951. Continuous Tapping Unit—See Figs. 1 and 2. Fig. 1 is a schematic drawing of the unit in place, showing front and side views. The component parts are identified in the caption. Fig. 2 is an actual photograph, front view, of the tapping unit attached to the base of the blast furnace. Operation. The operation of the tapping unit is quite simple. Essentially it consists of a narrow tapping bay surrounding the furnace tap hole, with a deep notch in the front wall. When the blast furnace is started this notch is open down to the level of the tap hole. Starting the furnace may be accomplished in several ways but the most satisfactory method is to plug the tap hole with clay, permitting metal and slag to build up inside the furnace. Before the liquid reaches the tuyeres, the plug is removed and the furnace is drained to the settler. The blast is then stopped momentarily while the notch in the front wall of the tapping bay is dammed with chrome brick and plastic chrome ore. The blast is again started, and the height of the dam is adjusted so that the liquid in the bay will counterbalance the internal pressure of the furnace. When the desired level is reached the slag and metal will overflow to the settler. It should be noted that the molten material ,is not siphoned from the furnace and that the metal 'acts as a liquid valve controlling the flow of slag through the tap hole. During normal operations the tapping bay is filled primarily with lead, covered with a thin layer of slag. Thus, the heavier lead plays the major role in compensating for variations in furnace pressures. Due to the high specific gravity of lead, changes in the liquid level in the tapping bay will never exceed a few inches. For this reason it is seldom necessary to change the height of the dam due to minor variations in operating conditions. Some turbulence of the liquid in the bay is essential at all times. This indicates that the level of the

Jan 1, 1963

By J. B. Ligon

Blast induced stress waves, propagating along the surface of a drift of an underground hardrock mine, were recorded and analyzed. Resistance strain gages, accelerometers and a velocity pickup were used in making the measurements. Although a full face blast was recorded, the stress waves were initiated by single borehole blasts for the majority of the project. A special instrument trailer was designed, constructed and utilized during the project. A reliable strain wave transducer was developed for measuring the stress waves propagating on the drift surface. A correlation study between strain and acceleration signals for P-waves was made which agreed well with theory. The use of stemming was found to reduce strain and acceleration magnitudes as predicted.

Jan 1, 2011

Recovery of Vanadium from Stone Coal Through an Environmentally Friendly Acid Leaching Technology

Sep 13, 2010

By Phillip J. Mackey, Rodney T. Jones

"Copper and copper alloys remain key materials for society today, with important uses found in the electrical, transportation, and construction industries. Copper demand is rising, with projections indicating that by 2025 global refined copper demand will increase to 29.5 million tons, up from the 22.4 million tons anticipated for 2015. This will require the opening up of dozens of new mines and numerous new smelters over this time period. Fortunately, Africa has significant reserves of copper, and African copper can once again play a key role in contributing to meeting the rising global demand for copper. This paper provides a brief overview of the current copper smelting operations in Southern Africa. INTRODUCTION Copper and copper alloys are essential materials for today’s modern world. The familiar green copper patina colour seen on buildings and other structures sometimes belies its true “green” characteristic – copper is essential for key emerging technologies such as wind turbines, tidal generating systems, solar energy systems, electric cars and the like. Consequently, it is believed that there will be continued growth in copper demand in the years ahead. Projections indicate that by 2025, as an example, global refined copper demand will increase to 29.5 million metric tons, up from the 22.4 million ton level anticipated for 2015. This will require dozens of new mines, and of the order of the equivalent of 10 to 12 new 0.5 million tons of copper/year-sized copper smelters (after factoring projected copper produced by electrowinning (EW))—overall, a huge undertaking. Fortunately, Africa has significant reserves of copper, and African copper can once again play a key role in supplying this rising global demand for copper. Africa’s share of global mined copper production was about 10% in 2014; however this will increase significantly in future if announced new projects eventuate. Southern Africa has an important role to play in this process. The present paper provides a brief overview of copper smelting in Southern Africa."

Jan 1, 2015

By Herbert H. Einstein

Rock mass deformability is commonly predicted using correlations with RQD or other indices of rock mass quality, or by extrapolation from large in-situ tests. Based on the probabilistic description of rock masses empirically developed in Part I a new approach was attempted in modeling for predictions of deformability. This approach decomposes the rock mass into spatially variable joints described by probability distributions, and intact rock blocks. Stiffnesses and elastic parameters are associated with the joints and intact blocks respectively, and deformations built up by adding the contributions of each. This model allows relaxation of many of the simplistic geometric assumptions which constrain parallel attempts to model deformation in rock masses. The model has been applied to four standard cases in order to test its results against previously existing models, and to check whether it replicates empirical correlations. When joints are taken as parallel, common empirical correlations are closely approximated by the model output. However, the closeness to empirical correlation breaks down when variability of the jointing geometry is increased.

Jan 1, 1979

By S. Strömberg, A. Jokilaakso

Two complex copper concentrates and one arsenical nickel concentrate were oxidized in simulated flash smelting conditions using a laminar-flow furnace. The concentrates contained tetrahedrite as Sb-bearing mineral and arsenopyrite and gersdorfite as As-bearing minerals. At high temperatures and low oxygen potentials, Sb tended to vaporize, but with high oxygen potentials it was captured in mixed oxide phases with copper and iron. Arsenic was found to follow antimony in copper concentrates, although with less sharp contrast between low and high oxygen potentials. In the nickel concentrate studied, arsenic was found to vaporize from the gersdorffite particles and, subsequently, condense on the other particles.

Jan 1, 1998

By Nic Slatalla

Resin anchored rock bolts are an effective tool to control the deformation of an underground opening because they combine high support capacity with fast installation. However, there are still numerous shortcomings concerning the understanding and interaction of the system bolt-resin-rock. Field and laboratory test series have been conducted for evaluating the load capacity and bond strength of resin grouted rock bolts in different host rocks under axial load. This paper describes that the behavior and shear strength of the system bolt-resin-rock depends on the rock type and discusses a simple correlation between peak shear strength and shear stiffness in the ratio 1:1000 which may moreover be helpful for estimating rock bolt capacity after installation.

Jan 1, 2006

By L Muñoz, L Steffen, W Vilas Boas, G Gontijo, R Macedo, C Braga, d D Machado, G Stevenson

Mines operating close to communities face growing challenges, especially with their drilling and blasting activities. Proper management of environmental and community impacts is critical to provide sustainability to the mining business in the long-term, by enabling the licensee to operate. This paper will present new technology solutions to minimise the impacts to communities and the environment from blasting operations. A case study of the wireless initiation projects conducted at Kinross Morro do Ouro Mine (located in Paracatu, Minas Gerais – Brazil), will be presented. Focused on overcoming the complex challenges in the mine, Orica and Kinross searched for initiatives to optimise the drilling and blasting operations. The team evaluated the WebGen™ wireless initiation system for controlling environmental impacts as well as operational flexibility and productivity. Since January 2023, three planned wireless blasts to demonstrate the technology and applications were executed. In the tests, the vibration level was able to be maintained lower than the limit of 3.0 mm/s while dust and flyrock impacts were well controlled. The main benefits of using this technology for the Morro do Ouro Mine are: reducing the number of blasts while increasing the blasted mass per month; control of projection of fragments using additional cover; dust control by watering the bench easily; lightning initiation risk reduction due to the absence of wires or tubes on the surface; flexibility in changing the blast day to better control the noise and dust; flexibility in mine planning mining (potential application in the future). The use of the WebGen™ wireless initiation system, enables improved productivity while enhancing safety and reducing impacts to communities. Implementation of this technology has enabled Kinross Morro do Ouro Mine to build trust with its neighbours, maintain the license to operate, and helping to mobilise resources in a sustainable way. This has allowed Kinross to position Morro do Ouro Mine as a world reference operation, especially in relation to innovation, safety, and social responsibility.

Sep 1, 2024

By S. Kittel, P. Galleguillos, H. E. Urtubia

The rougher flotation at Escondida consists of 80 cells of 100 m3 each, with injected air. Escondida has developed a system of automatic control of the rougher flotation using video cameras, which have been operating since 1997 for remote monitoring and manual control. Since 1999, an image processing software and a group of rules have allowed implementation of an expert system. To date, the expert system controls the superficial speed of each cell by adjusting the air flow and the froth depth of the flotation bank. Preliminary tests of the expert control on two of the eight rows gave 1.2% higher rougher recovery at a 92% degree of confidence. The proven benefits are already sufficient to move towards a complete plant implementation.

Jan 1, 2001

By A. R. Denison

The area discussed in this report comprises a group of 38 counties lying in the northeast corner of Texas. It covers all, and extends beyond, the borders of what is commonly described as the East Texas Basin. It includes two major oil fields, Van and East Texas; two major gas fields, Bethany and Waskom; and a number of fields, both oil and gas, of lesser importance. All commercial oil production comes from beds of Upper Cretaceous age and almost exclusively from the basal member, the Woodbine sand. Gas is produced from both Upper and Lower Cretaceous beds with the newer production from the older beds. East Texas Field This field continued as in 1932 and 1933 to dominate the drilling and production situation throughout the oil business. A total of 3681 producing wells was completed in this field during 1934. This is an increase of 1215 over the 2466 producers completed during 1933. Total wells

Jan 1, 1935

By I. M. Morsi, S. Z. El-Tawil, O. A. Fouad, K. A. El-Barawy, M. B. Morsi, M. M. Nasr

Upgrading of a low-grade titanium slag (~55% TiO2) with high silica, calcia, magnesia and iron contents has been studied using sulphation roasting technique using SO2/air gas mixture followed by hydrochloric acid leaching. XRD analysis of the sulphated slag reveals the presence of kennedyite (Fe2O3. MgO. 3TiO2), rutile (TiO2), calcium sulphate (CaSO4) and calcium silicate (3CaO.SiO2) phases. The residue after leaching contains mainly kennedyite, rutile phases and free silica with traces of calcium silicate phase. Synthetic rutile that has about 83% TiO2 can be produced at the optimum conditions. Thermodynamic calculations give rational explanations of the obtained results.

Jan 1, 2005

[Ferro Alloys Producers Association The South Africa Institute of Mining and Metallurgy www.saimm.co.za Mintek www.mintek.co.za Eskom www.eskom.co.za ]

Jan 1, 2004

By Dean Brox

The use of Tunnel Boring Machines (TBMs) for tunnel construction of long tunnels in the Andes of South America has been of mixed success in the past due to a variety of reasons and key lessons can be recognized. A review of past TBM tunnel projects in the Andes has unveiled some interesting findings for different TBM tunnel approaches with both world records of progress as well as nearly in-completed projects with machines being abandoned. Key considerations for the use of TBMs for tunnel construction in the Andes include geological issues; (faults, rock type, rock strength, rock abrasivity, durability, groundwater inflows),depth of cover and the potential for overstressing/rockbursts, site access and terrain, portal locations, intermediate access possibilities, minimum tunnel size, support requirements, contractor and labour experience, and project schedule demands. TBMs offer highly recognized schedule benefits(high progress, no concrete lining) for a project if intermediate access adits are limited as well as hydraulic benefits for water conveyance projects. Minimum specifications for TBMs can be easily developed to suit the unique requirements of any project so as long as all factors are carefully considered. The overall conditions and factors associated with some projects may suggest that it is not appropriate to use TBMs due to a perceived high risk. Finally, access for geotechnical investigations by drilling in the commonly steep terrain of the Andes is typically difficult and often not impossible. Alternative approaches for geotechnical investigations for TBM tunnels including comprehensive mapping, high-resolution airborne electric-magnetics for delineation of possible fault zones, and rock block sampling is presented and discussed.

By K. V. Raj, M. McNinch, A. L. Miller, J. Wilson, D. A. Parks

Diesel particulate matter (DPM) has been shown to contribute to various adverse health effects on underground miners. In order to reduce worker exposures, it is critical to measure the levels of DPM in the active work settings and in real time. However, the 5040 method, developed by the National Institute for Occupational Safety and Health (NIOSH), which quantifies the mass of elemental carbon (EC) and organic carbon (OC) in the samples, is based on full-shift samples, and can take days or even weeks for results. Use of real-time monitors could significantly reduce the risk of DPM exposure to miners, and available monitors have been shown to quantify DPM, mainly using the EC and other surrogates. The NIOSH Spokane Mining Research Division is conducting research aimed at developing a field-portable DPM monitor that is able to quantify both EC and OC. One part of this work is to understand the effect of OC on currently available real-time DPM monitors. This paper will present the results from experiments that were designed to observe the effect of OC on real time monitors and compare the results with the NIOSH 5040 method. BACKGROUND Diesel engines remain ubiquitous in mining environments and, as such, are one of the primary sources of ultrafine- and nano-aerosols in the mining environment in the form of diesel particulate matter (DPM). As a result of their small size, DPM has longer residence times in a mine atmosphere than the typically larger mechanically generated dust [1]. In addition, the small size enables DPM to penetrate deeply into the respiratory system [1], and exposure to DPM has been shown to contribute to various adverse health outcomes of the pulmonary system [2] and cardiovascular system [3]. Diesel exhaust has been classified as a carcinogen to humans (Group 1) by the International Agency for Research on Cancer [4]. Due to mounting concern about adverse health outcomes, extensive efforts are being made to reduce workers’ exposure to DPM, with the high exposures that often occur in underground mines being of particular concern [5]. New technologies are being developed to reduce engine emissions and thereby airborne DPM levels, including advanced engine technologies, a host of aftertreatment systems [6], and a variety of alternative fuels. The latter have been shown to markedly decrease respirable DPM and other hazardous components of diesel emissions from mining vehicles [7], yet high exposures persist, especially in underground mines [8]. In order to reduce worker exposures, it is critical to measure the levels of DPM in active work settings. In mine settings, exposures to DPM are measured by collecting air samples on filters (usually full-shift samples) and sending them to a lab for analysis using the Mine Safety and Health Administration (MSHA) P13 method, a variant of the National Institute for Occupational Safety and Health (NIOSH) 5040 method. The 5040 method is designed to quantify the mass of elemental carbon (EC) and organic carbon (OC) on the samples [9], which is then used to determine the concentration in the sampled air. MSHA has set a limit for exposure, which is based on the concentration of total carbon (TC), or the sum of both EC and OC. The allowable TC in the air (time-weighted average over the shift) is 160 μg/m3 of TC [10].

Jan 1, 2019

By R. H. Snow

Although industrial size reduction methods have an energy efficiency of only about 1 percent, methods of size reduction have not changed much for many years. One reason for slow progress has been the oversimple viewpoint that a single law should exist to relate size reduction to energy input. Modern simulation methods decompose the grinding process into a grinding rate function (selection function) and a breakage function. The breakage function is difficult to measure, and it usually requires tracers if it is determined from milling experiments. Prediction of breakage functions from basic principles is one objective of this paper. In this study we focus attention not on the gross energy input to the experiment, but on the spatial distribution of stress energy within the particle. We are led to this viewpoint by experimental observations of a few previous investigators (Bergstrom2, Rumpf3, Axelson4) and our own observations. Oka and Hiramatsu recently used their calculations of stress within particles for prediction of breakage, but again they tried to correlate the size of the fragments with the total stress energy, rather than the approach we propose. We assume that the stress energy is stored in the interior of the particle as the load is increased, until the particle breaks. We assume that each element of the particle breaks into fragments of a mean size that depends on the locally-stored stress energy. The size distribution of fragments is the computed from maps of the stress-

Jan 1, 1972

By H. Walqui

The Empire concentrator was built in four stages, with the latest stage accounting for 50% of the overall plant capacity. Over the past 5 years, the average throughput of the three grinding lines has decreased by 50 LTPH (15%) without significant changes in ore characteristics and despite the addition of secondary grinding capacity to supplement the existing pebble mills that are the constraint of the grinding circuit. This paper discusses the different areas under study that are aimed at optimizing grinding circuit utilization which includes improving system logic, pebble crushing operation and pebble mills operation.

Jan 1, 2009