Search Documents

By Néstor Deza, Kim Montes

En los últimos 20 años la operación minera en Antamina ha profundizado su tajo, el stripping ratio y la distancia de acarreo de desmonte, se han seguido incrementando para mantener la producción metálica. Tal como ocurre en las todas operaciones mineras de tajo abierto, se espera en los próximos años un incremento sustancial de la cantidad de desmonte a remover conforme se avance las siguientes extensiones de vida. En adición a esta situación, los recientes compromisos globales de reducción de emisiones de carbono exigen reducir progresivamente hasta eliminar el 100% la emisión de carbono, opuesto a lo requerido para seguir operando con métodos convencionales. Estos dos factores afectan la sustentabilidad en el largo plazo en todas las empresas mineras maduras como en el futuro de Antamina.

Sep 30, 2022

By Thomas C. Anderson

Thirty-four retaining walls are part of the $46 million upgrade of a 1942 depressed highway in Highland Park, Michigan near Detroit. This project will close a missing link between two newer roadways, I-75 and the John Lodge Freeway. The existing 75 ft. wide, six lane Davison Freeway is being replaced by a eight to ten lane, 200 ft. wide depressed highway in a limited right of way. The highway will be 20-25 ft. deep and 1.5 miles long. A design/build decision by the Michigan DOT saved about 37% of the engineers estimated cost of $19 million for the walls. The successful pre-qualified specialty contractor utilized an innovative solution for the walls consisting of tiedback/cantilevered walls on the north side and mechanically stabilized earth walls on the south side. All of the walls have an identical cast-in-place architectural facing.

Jan 1, 1999

By R. J. McNally

THERE are three primary plant nutrients—nitrogen, phosphorus, and potassium—expressed in any fertilizer compound as percent N, percent P 2 O 5, and percent K 2 O, in that order. This article will be concerned with the first two. The chief source of P 2 O 5 is phosphate rock. As found in the western states phosphate rock is essentially tricalcium phosphate-calcium fluoride (fluor-patite). As such, it is quite water insoluble.

Jan 1, 1957

By E. Yalçin

The data set often contains one or more secondary variables. These secondary variables are usually spatially cross correlated with the primary variable. The addition of the cross-correlated information reduces the variance of the estimation error by using the cokriging method. The grade estimation results of ordinary kriging and cokriging methods are evaluated and it was found that the estimation variance of cokriging method is slightly lower than ordinary kriging. The effect of variation of block dimension on the estimation results is also investigated and it was seen that the cokriging estimation variance values also decrease as the block dimension increases.

Jan 1, 2005

By Ling Yang, John Henderson

Self-diffusion coefficients of copper in molten copper have been measured by the capillary reservoir method in the temperature range 1140o to 1260°C. The results can be represented by the equation D = [(1.46 * 0.01) x 10-3) exp [(-9710 * 710)/RT] cm2/sec. The energy of activation agrees within the limit of experimental uncertainty with that for viscous flow. The relationship between the diffusivity and coefficient of viscosity is best described by the equation D = kT/4pnr cm2/sec. MEASUREMENT was made of the self-diffusion coefficient of copper in molten copper in the temperature range 1413º to 1533ºK, using the capillary reservoir technique and CU64 as the radioactive tracer.The procedures for filling the capillaries, making the diffusion run and evaluating Dcu from the counting results were the same as described previously.1,2 All experimental operations involving the melt were carried out in a purified argon atmosphere. A graphite crucible, enclosed in a McDanel tube, was used as a container for the melt because of its satisfactory nature as a refractory material and the low solubility of carbon in copper. Graphite was also used for the capillary material. A McDanel thermocouple sheath, to which graphite radiation shields were affixed, was used to hold the capillaries. By moving this sheath through a rubber seal at the top of the McDanel tube, the capillaries could be lowered into or raised out of the melt. A Globar furnace with a constant temperature zone (± 2°C) of 2 in. was used to heat the assembly. The temperature of the furnace was the equilibrium value corresponding to a given setting of the transformer. Temperature was measured with a Pt-10 pct Rh/Pt thermocouple and varied during a run

Jan 1, 1962

By Elsa Olivetti

Life cycle assessment (LCA) is used increasingly as a tool to provide quantitative metrics of environmental impact and inform early stage materials selection decisions. One common challenge in LCA stems from allocation of burden when multiple adjacent products share some of the same processes. A critical example of this is the partitioning of benefit or burden at product disposition in open-loop recycling scenarios. This work reviews the challenge of allocation and investigates the various methods proposed for allocating end-of-life (EOL) burden. Specifically this work examines whether these methods lead to different results and explores the trends in allocation method bias for or against particular materials classes.

Jan 1, 2010

Development of the Boleo Process Flow Sheet and the Direct Solvent Extraction (DSX) Circuit for Cobalt and Zinc Recovery The metallurgical process designed to treat the El Boleo Cu-Co-Zn-Mn ore involves a sulphuric acid leach in seawater under oxidative and then reductive conditions to maximise metal extraction. Copper and cobalt are recovered as cathodes by electrowinning, zinc and manganese as zinc sulphate monohydrate and high quality manganese carbonate, respectively, by precipitation after a number of separation and purification stages. One of the key purification stages of the Boleo metallurgical process is the CSIRO DSX circuit. The DSX circuit was developed using the synergistic solvent extraction (SSX) technology. Initially, a synthetic solution was studied, and by adding 0.4 M LIX63 to 0.5 M Versatic 10 in Shellsol D70, large synergistic shifts were obtained for cobalt (?pH50 4.24) and zinc (?pH50 1.62). After a single contact, the separation factor of metals over manganese reached over 6,000 for cobalt and over 380 for zinc, indicating excellent separation of cobalt and good separation of zinc from manganese, magnesium and calcium. The SSX system was further optimised with the modified synthetic pilot plant solution. The extraction of cobalt and Zn after a single contact was 93 per cent and 70 per cent, respectively, while the Mn concentration in the loaded organic solution was only 0.28 g/L. A proof of principle pilot plant operation was conducted in 2004 and a demonstration pilot plant for final engineering design in 2006 with outstanding performance of the DSX circuit. For the demonstration pilot plant, the overall recovery of cobalt and zinc exceeded 99 per cent with a raffinate containing only 4 mg/L Zn and 1 mg/L Co. The DSX organic system showed no sign of degradation during the pilot plant operation, indicating good chemical stability under the anticipated commercial operating conditions. The DSX circuit will be implemented in the future Boleo processing plant.

Sep 13, 2010

By Walter Hermülheim, Klaus-Dieter Beck

In German hardcoal mining approximately 1 or 2 cases of spontaneous combustion are recorded per 10 million tonnes of saleable output. In approximately every 20th spontaneous combustion case, CH, is ignited. By the example of a fire caused by spontaneous combustion on Friedrich Heinrich colliery, an overview on the measures taken for firefighting and explosion prevention is given. These measures comprise (in sequential order) - early fire detection by CO-monitoring, - gob-sealing measures against ventilation air leaks, - full-space inertization of the coalface subsequent to a CH,- deflagration, - installation of a target inertization of the caved-in gob under the protection of the full-space inertization, - re-opening of the fire zone and reestablishment of the ventilation-air current, - completion of the salvaging work with continued target inertization of the caved-in gob and further sealing measures (monolithic packing), - sealing of the coalface after salvaging. The measures described allowed gain of control of a safety- critical (because close to the face) gob fire caused by spontaneous combustion, in spite of a CH, deflagration, within few days only, and salvaging of equipment from that coalface and start-up of the follow-up coal-face on schedule. The measures taken as well as the experiences gained allow deduction of general safety criteria for fighiing of gobfires caused by spontaneous combustion, and for controlling the explosion risk. e.g. - warning and alert thresholds for early detection of fires, - criteria for spotting of the zone of fire, - rules for tightening caved-in gobs, - thresholds for the retreat of firefighting crews from the vicinity of the zone of fire, and for starting ineiization, - considerations for positioning of and strength requirements for stoppings with/without inertization, - flow-by-volume adjustment of inertization, - safety rules for work with respiratory apparatus in the inertized zone, - safety rules for the re-opening of zones of fire. The considerations end up in the conclusions that the duration in terms of months of the classic cycles of sealing, waiting, and reopening can nowadays be reduced to a few days only by purposeful combination of full-space inertization and locally confined tar- get inertization of the gob area. The earlier high risks incured by the mine resuce squads en- trusted with sealing of zones of mine fires under explosion hazards can be reduced by the method described, provided the safety regulations are conformed with. In this way, intertizing contributes substantially to reduction of down-time caused by mine fires, to preservation of recoverable parts of the deposit, and to improved safety of the fire-fighting crews.

Jan 1, 1997

There is a significant amount of historical mining and exploration information available. This information is often distributed throughout a number of reports or plans, available from a variety of sources, and in many differing formats. The ability to capture paper-based historical information in a modem digital format provides mining and exploration companies with valuable information that can be used in a number of ways; for example, reassessments of exploration or mining work previously undertaken, or used in conjunction with current exploration information.   The purpose of this paper is threefold. Firstly, to present the paper-based historical information; highlighting some of the problems encountered, solutions to those problems, and any assumptions used. Secondly, to present the historical data in digital format, and demonstrate the tools available to analyse geological and associated information, and finally, to illustrate some of the potential future applications of the information, including mining optimisation, mine design and scheduling.   The Glenorchy scheelite/gold prospect has been used as an example. Within the overall prospect two smaller areas were selected. The Mount McIntosh and surrounding areas, focuses on exploration and surface excavation information. The Mount Judah area (State and Kelly-Taylor workings) focuses on underground mining and exploration information.  

Jan 1, 2001

By Alan Alves Vieira

Uma das maneiras mais eficientes de aumentar a campanha dos refratários de conversores é o uso de técnicas de slag splashing e slag coating. Nestes processos, antes de sua execução, a escória de fim de sopro é modificada pela adição de materiais contendo, principalmente, MgO. Escórias de conversor contendo alto teor de FeO tem, como fase de equilíbrio mais provável a magnesiowustita (MW). Este estudo visa determinar se, nos curtos tempos de processo em conversor, e sempre a temperaturas bastante inferiores ao ponto de fusão do MgO, ocorre a dissolução do MgO e a saturação da escória em MW ou se a escória se mantém fora de equilíbrio. Os resultados indicam que a MW é formada e, em muitos casos, sua composição pode ser prevista com razoável precisão através de cálculos de equilíbrio por termodinâmica computacional.

Oct 30, 2017

By H. Wyslouzil

"The Kelsey Centrifugal Jig is a gravity separation device which utilizes the principles of the conventional mineral jigs but with the additional feature of being able to vary the apparent gravitational field. This is accomplished by utilizing the specific induced movements of the conventional jig within a centrifuge.Pilot plant trials have been underway since July 1988 to evaluate the potential applicability of this technology to various process streams at Rio Kemptville Tin.The grade/recovery relationships for samples treated in the jig were consistently better than results obtained from tables. Recoveries of more than 90% were attained at concentrating factors ranging up to 20. When compared with electrostatic separators, the jig achieved equivalent metallurgical results in a two stage process, without the expensive requirement of filtration and drying. Recoveries exceeding 96% were achieved with final concentrate grades averaging higher than 60% tin.INTRODUCTIONMineral jigs have been used for hundreds of years. Many different types have been developed, and each one has numerous variations. In recent years, the idea of applying centrifugal forces to conventional jigs has been put to practical tests and today a number of units are in commercial production. In principle, by enhancing the apparent gravitational field, it should be possible to recover finer particles by overcoming viscosity and surface effects which tend to limit existing gravity devices. In addition, it may be possible to use gravity to separate minerals with much smaller specific gravity differences."

Jan 1, 1990

By Cecilia Arrue, Dominic Fragomeni, N. O. Lotter

"A statistically designed benchmark mill survey was carried out in July 2005 at the Kidd Creek Concentrator, D Division circuit, which processes Ni/Cu ore from the Montcalm deposit. A structured statistical survey approach was followed, together with defined quality controls, which would assign a 95 percent level of confidence in the result.A set of six surveys were completed over a limited time; the corresponding stream samples of the surveys found acceptable were combined to obtain high confidence composite samples. The head grade of each survey is compared to two distributions to test its acceptability; surveys that fail to conform to these trials are rejected. The accepted set of surveys, which is a robust representation of the process, is prepared into a composite for QEM-SEM analysis and mass balance purposes.Where the above practice is a standard procedure in Falconbridge for QEM*SEM purposes, in this case each individual two-hour survey unit was measured and analysed for a mass and value balance. It is shown that none of the individual mass and value balances close as well as the composite set of accepted two-hour survey units. This founding is in keeping with the averaging properties of the Central Limit Theorem.INTRODUCTIONMontcalm OperationsNi/Cu bearing ore from the Montcalm deposit is being processed at the Falconbridge, Kidd Creek Concentrator in a modified D Division circuit. The circuit was commissioned in the fall of 2004. Ore is crushed at the minesite to –19 mm and trucked to Kidd for delivey into the 4 parallel fine ore bins.Ore is milled in a rod mill followed by cyclones and 2 parallel ball mills. The grinding circuit treats Montcalm ore at an average feed rate of 100 wet tonnes/hour (750,000 tonnes/annum) and produces a flotation feed particle size of 83% -53 um. A simple flowsheet including bulk Cu/Ni roughing and 2 bulk cleaning stages followed by Cu/Ni separation in 2 stages is practiced. Soda ash is used as a pH modifier in bulk flotation. SIBX is the collector. Lime and Dextrin are added into Cu/Ni separation for the depression of pentlandite."

Jan 1, 2007

Arsenic (As) removal behavior from Changgoon mine tailings was investigated using Acidithiobacillus ferrooxidans (A. ferrooxidans) in well-controlled batch reactors by varying pulp density (0.5?4%, pH=1.8, temp=30oC), reaction initial pH (1.8?2.2, pulp density=0.5%, temp=30oC), and temperature (25?35oC, pulp density=0.5%, pH=1.8). The initial concentration of As in the mine tailings used for bioleaching tests was about 30000 ppm, and the size range of tailings used in this study was 63?74 µm. The reaction speed and initial cell concentration were fixed to 150 rpm and 107 cells/mL, respectively. To complement leaching experiments, pH, oxidation/reduction potential (ORP), and amount of ferrous/ferric ions in leachate were analyzed. Scanning electron microscopy and x-ray diffraction analyses were also conducted for the samples before and after leaching to see if any morphological and compositional changes in tailings took place during leaching process. The As leaching efficiency increased with decreasing pulp density, decreasing pH, and increasing temperature in the presence of A. ferrooxidans. Specifically, no significant change in As removal rate was observed when pulp density d 2% while the removal rate dramatically decreased at pulp density of 4%. Regarding pH effect, As removal rate was much more enhanced at lower pHs (i.e., 1.8 and 2.0) compared to pH 2.2. Increasing temperature was observed to tend to enhance As removal rate, showing about 20% enhanced leaching rate under 35oC compared to 25oC and 30oC at the elapsed time of 5 days. The results for As removal behavior at different conditions (i.e., pH, temperature, pulp density) were consistent with the change in pH, ORP, and ferric ion concentration in leachate, showing greater removal rate at the condition with lower pH, and higher ORP and ferric ion concentration in leachate. Furthermore, decreasing removal efficiency was likely in part due to the extent of the formation of by-product (i.e., jarosite) of ferric ions.

Feb 27, 2013

By André De Araujo Abilio

Geopolímero é um material inorgânico formado por ativação alcalina durante a qual processos de polimerização de alumino-silicatos formam a cadeia polimérica que consiste em tetraedros de Si-O e Al-O. Com o intuito de encontrar subprodutos para serem usados como uma alternativa de aglomerante na formulação do geopolímero, um subproduto oriundo do processamento de rochas ornamentais foi utilizado. O presente estudo consiste na caracterização da capacidade de flexão do material geopolimérico resultante da adição do granito como aglomerante alternativo. Estudos foram elaborados de modo a avaliar ambos o efeito e a viabilidade de seu uso em formulações futuras do geopolímero.

Aug 16, 2017

By Chris Brown

"The Island Copper plant was designed and built by Fluor Utah Ltd, in conjunction with Utah design staff, Originally designed to treat 33,000 tons/day (t/d) of ore, the current average milling capability is 38,000 t/d (Nov'74). The first of six semi-autogenous grinding lines was brought on line in October 1971, startup of the remainder being governed by equipment delivery schedules.The summer of 1973 saw the start-up of an additional three ball mills, and attainment of the present production level. The current process flowsheet is shown in simplified form.CRUSHINGThe crushing circuit is relatively simple, comprising single stage crushing of the ore followed by screening to fine and coarse fractions.The crusher is a 54 x 74in. Allis Chalmers Superior Gyratory with a setting of 9-lOin., driven by a 500-hp motor. Trucks dump on three sides of a rectangular dump pocket. An 84in. x 20ft. link belt apron feeder draws crushed ore from a 250-ton surge bin below the crusher, discharging onto a 72in. wide inclined steel cord conveyor belt. A fixed splitter box at the conveyor discharge separates feed to two parallel Jeffreys 6 x 20ft. vibrating grizzlies for screening into +4in. and -4in. fractions. The fractions are collected on short reversible conveyors which feed the coarse and fine ore stacker conveyors. Trippers distribute ore to outside stockpiles adjacent to, and above, the concentrator grinding 'floor."

Jan 1, 1975

By Evan Dressel, Mark S. Diederichs, Kathy Kalenchuk

As hard rock mining develops deeper over time, there is an increasing need to predict the spatial and temporal distribution of adverse seismogenic rockmass reaction to mining. Real-time monitoring and feedback of mine data are used to tactically manage risk associated with induced-seismicity; however, strategic risk management requires reliable tools for forward predictions of seismic hazard. The forward prediction of seismic hazard is strengthened by understanding of potential seismic intensity, which often relies on well calibrated mine-wide numerical models. This paper uses a case study to explore how future seismogenic potential and the nature of future seismicity can be domained according to numerically predicted stress-strain paths at past seismic event locations. Delineation of high confinement seismogenic volumes vs. lower-confinement, high-strain seismogenic volumes at the mine-scale can be achieved, based on a loading and unloading stress path analogue, to refine understanding of seismic intensity. Practical qualitative and quantitative methods to achieve this delineation will be demonstrated. Once seismogenic mode (high-stress vs. high-strain) is identified, detailed analyses of seismic source parameters demonstrates change in seismic hazard between the domained volumes.

Apr 26, 2022

By A L. Withy

This paper is intended as a review from a planner's viewpoint, of the relationship between town and country planning, a primarily government activity, and the minerals industry, which, with the exception of coal, is a largely private enterprise activity. The paper first considers the nature of the system of planning in New Zealand, and the objectives sought by planners in relation to minerals are discussed. The reasons why these objectives are not generally being achieved are investigated. A final section deals with the gap between objectives and achievement, and suggests a number of ways in which this gap may be narrowed.

Jan 1, 1976

By William H. Hansmire

The Modified Detroit River Outfall No. 2 (MOD DRO-2) will discharge treated wastewater to the Detroit River. Construction of a 6.4-m-diameter, 1.9-km-long tunnel was halted in 2003 by flooding during tunneling with an open face hard rock TBM. A new design for a higher rock tunnel, a ?Modified? design, was completed in 2007 and Notice to Proceed to the tunnel contractor was given in November 2008. Project duration is four years for completion of tunneling and start of outfall tunnel operation. This tunneling project has high groundwater pressure (5 bar), pervious limestone rock of up to 140 MPa (20,000 psi) strength, and hydrogen sulphide in the groundwater. The new tunnel will be connecting to access shafts and outfall diffuser riser shafts previously built for the now-abandoned tunnel. The new tunnel design construction contract, and initial planning to use a pressurized-face (slurry) hard rock TBM are presented.

By Christa Overby

As part of the City of Portland, Oregon?s East Side Combined Sewer Overflow Tunnel Project, nine separate 2,130 mm (84-inch) diameter reinforced concrete pipe microtunnel drives totaling approximately 2,380 m (7,808 ft) are being constructed to divert flows from several of the existing outfalls to the main tunnel. The drives were constructed in challenging ground conditions that include soft soils under the ground-water table, large amounts of wood and metal debris, and close proximity to sensitive structures. While all of the drives will be addressed, the focus of the paper will be on the 931 m (3,055 ft) continuous drive connecting Outfall 46, currently the longest microtunnel driven in North America.

By Enrique Ibarra, Manuel J. Mendoza

"Abstract: This paper describes the current state-of-practice for the design of cast-in-place drilled shafts in granular soils under axial loading, addressing recent advances that take into account the surrounding soil grain size distribution and their behavior. The important role of the gravel content in the shaft response under axial loading is emphasized. Usual design approaches in Mexico are described, and the results of load tests from different sources are discussed. The analysis emphasizes the primary contribution of the lateral area of shafts to their axial bearing capacity, raising doubts regarding the common local idea of “point bearing shafts”. Finally, some lines of research are noted to permit advances in the important field of deep foundations. 1 INTRODUCTIONIn Mexico, cast-in-place drilled shaft foundations are widely used to support various structures in the west area of Mexico City, where alluvial and volcanic deposits predominate. Deep foundations are also used in modern construction works located in other major cities of Mexico. In fact, the use of drilled shafts for tall buildings and overpasses in the center of Guadalajara as well as in transportation works related to the Metro and roadways in Monterrey is well known. It is worth mentioning that these same structures have been applied in road bridges throughout the country.Procedures for pile construction in Mexico have been basically the same for the past 20 years (Paniagua et al., 2005); however, modern equipment has been incorporated into the construction industry, including innovations in sludge-drilling technology, control and the quality of the castings. In addition, novel and efficient procedures such as construction with continuous auger displacement piles have been implemented (Auger Cast in Place, ACP) and have begun to be used locally with success (Schmitter and Paulin, 2006).However, it can be argued that the technological developments that have resulted in more efficient construction procedures have not included a breakthrough in the full understanding of the phenomena or basic mechanisms of load transfer from piles to the surrounding subsoil and therefore in supported, tested and practical design methods. This is particularly true when seeking to determine the unit side shear strength of shafts drilled in granular media with gravels, where it has been observed that the commonly used calculations developed for sands underestimate the load-bearing capacity by frictionin a most important way. Due to the above reasons, it seemed appropriate to present in this paper a review of the current stateof- practice in Mexico for the design of cast-in-place drilled shafts, particularly in granular media, highlighting some recent advances and research that takes into account the grain size distribution and behavior of granular soil."

Jan 1, 2014