Search Documents

By M. Ng

As part of a long-term study of titanium minerals processing being undertaken by the Julius Kruttschnitt Mineral Research Centre, techniques have been developed to measure the resistivity of ilmenite, rutile, zircon and other associated minerals. The techniques have proven reproducible and have allowed the measurement of resistivity under conditions of varying temperature, surface condition and surface moisture adsorption. The measured values can be linked to the separability of the minerals in the dry plant, and hence are useful as a diagnostic test for existing plants when performance deteriorates, or for greenfield sites to investigate potential problems. One of the major problems in electrical separation of titanium minerals is surface coating on the mineral grains. Coatings can make normally conductive minerals such as ilmenite and leucoxene behave much more like non-conductors. Electrical separation of surface contaminated ilmenite from non-conductors then becomes extremely difficult unless the surface contaminant is first removed. The resistivity measurement technique was used to evaluate the effect of surface cleaning on the resistivity of ilmenite and zircon from a Western Australian deposit which will shortly be in production. Ten different attritioning methods were evaluated, ranging from simple rinsing inwater to chemical attritioning in sulphuric acid combined with ultrasonic leaching. A roasting and quenching step was also investigated. As would be expected, the gentler treatments, such as rinsing in water or Calgon, had only amoderate effect on the ilmenite surface coatings. Ilmenite resistivity decreased by about 1 order of magnitude from 5.6 x108?m to between 2.5 and 4.4 x107?m. More intense treatments had a much more pronounced effect. The most effective, reduced ilmenite resistivity to 6.5 x105?m or three orders of magnitude. Zircon was relatively unaffected by any of the attritioning methods, with only a small increase in resistivity observed from 8.0 x1012?m to 2 x1013 ?m. The results show that measurement of mineral resistivity allows the effect of surface treatments to be easily quantified in a way that has benefits for greenfield site development where only small samples are available for testing. The effect of surface moisture has also been investigated using resistivity measurements. Measurements were made on zircon in an environmental chamber in which both humidity and temperature could be closely controlled. Zircon resistivity at 60 deg C decreased from 6 x1011?m at 5% relative humidity to 8 x108?m at 95% humidity. Moisture content and moisture re-adsorption from dry of zircon and number of other minerals were measured using a Mettler moisture analyser. Zircon adsorbed the least amount of surface moisture (0.05–0.09%) but re-adsorbed moisture from dry the fastest, reaching 98% of the original level in 10 minutes. Leucoxene adsorbed the most moisture (0.67%), but was much slower re-adsorbing this moisture from the dry state, reaching only 63% of the original level in 10 minutes. The difference was attributed to the surface characteristics of the grains, the leucoxene being much more porous than the zircon examined. The resistivities and differing rates of moisture adsorption can be used to quantify the effects of changes in atmospheric conditions of the performance of electrical separation in dry plants.

Jan 1, 2003

By E. Stemn

Incident investigation is of utmost importance in most high-risk industries. This study was undertaken to study the content of past investigation reports to determine the effectiveness of the incident investigations. The study uses a semi-quantitative method to assess the effectiveness of incident investigations in the Ghanaian mining industry by evaluating the quality of past investigation reports. The assessment tool consists of 5 elements with several indicators and rating scales for assessing the quality of an investigation report as a measure of the effectiveness of the investigation. The method was applied to 304 investigation reports of 3 Ghanaian large-scale gold mines, and the results correlated with incidence rates of the mines to determine if any relationship existed. The results showed that the mines differ significantly in the quality of their investigation reports, suggesting differences in the effectiveness of their investigations. In addition, the incidence rates of the mines negatively correlated with some elements of the assessment tool. In general, the method was found useful and revealed areas where improvement is needed. INTRODUCTION The importance of learning from incidents is well documented in the literature. For instance, some scholars regard learning from incidents as important for improving safety [1,2]. Thus, many organisations spend considerable resources in identifying lessons from incidents and subsequently on the process of improvement that follows the identification of lessons. It is therefore important for such organisations to determine the effectiveness of their learning from incidents processes, in order to identify specific areas where improvements are needed, so that interventions can be as specific as possible. The learning from incidents process models the plan-act-check-do approach of management systems, often consisting of four major stages, namely; data collection and incident analysis, planning interventions, implementing interventions and follow-ups and evaluation [3,2]. The investigating and analysis of incidents have been regarded as one of the vital stages of the learning process since it is the stage where lessons are identified [3,2,4]. It has also been noted elsewhere in the literature that results of the previous stage of the learning process are important for the next stage [3]. For example, ineffective incident analyses could result in the planning of ineffective remedial measures. One of the primary aims of incident investigations is to identify lessons from previous incidents which when implemented can prevent future recurrences or minimise the effects of future incidents. There is thus the need for organisations to assess the quality of their investigations periodically since it is one of the means they adopt to improve safety and the quality of remedial measures to some extent depends on the effectiveness of the investigations. Although previous studies [5,2] have assessed the effectiveness of the learning process, and some aspects of the learning process, such as incidents reporting, there is less focus on the effectiveness of incident investigations. The research described in this paper was therefore conducted to contribute to this gap, focusing more closely on incident investigation reports.

Jan 1, 2019

By Patrick M. Y. Waye

As mines utilise more automation in mining operations to improve efficiency and safety, a corresponding increasing demand is placed on the transport of information. Some of the recent technological advances in underground telecommunications are described for various data, voice and video applications. In particular, two new innovative underground communication systems are described, one with high speed data at 30 Mbps and the other for mine wide evacuation and safety applications. The high speed data system incorporates stateof- the-art data networking technologies and the existing leaky cable narrow band radio channels. The new system provides over the same basic infrastructure the high speed data network at 30 Mbps TCP/IP Ethernet with 100 Base-T interconnection, plus 32 narrow band radio channels. The second system is a system for mine wide evacuation with "through the earth" communication infrastructure. Emergency situation can be communicated to and from all the miners within seconds through a central control location. The technology involved does not require leaky cable or any other similar transmission media installation. Many applications are possible, including warning miners of emergency situations, mine rescue operation to communicate with trapped miners, regular reporting from miners working alone.

May 1, 2001

By T. Karalis

Perlite is a generic term for naturally occurring siliceous rock. It is a form of natural volcanic glass the main constituent of which is amorphous silica (70-76%). Perlite, when heated rapidly to its softening temperature range, expands from four to twenty times its original volume, due to the presence of 2-6% ?combined? water, in a manner similar to popcorn as the H2O molecules vaporize and create countless tiny bubbles, which account for its exceptional physical properties: light weight (30-150 kg/m3), low thermal conductivity, cellular structure, in general. These properties make perlite adaptable for numerous end-uses, which can be distinguished into 2 categories: Expanded perlite applications in: a) Construction Materials market (e.g. Acoustical Tiles, light-weight insulating Mortars, self-levelling Concrete), b) Agriculture (e.g. Hydroponics), c) Food and Chemical industry (e.g. Filtration Media, Filler, etc.), d) Insulation and Heat resistance technology (e.g. Cryogenic vessels, Refractory Bricks, etc.). Unexpanded Graded perlite applications in: a) Phosphoric Fertilizers industry (additive in H3PO4 production), b) Foundry technology (slag-aid, insulating and heat resistance agent).

Jan 1, 2006

By Murali M. Gadde

Perimeter mining is a special form of very productive partial extraction method practiced at some mines in the United States. In the Illinois Basin mines where all major coal seams have weak underclay in the immediate floor, experience shows that any long-term ground control issues will arise due to floor failures rather than instability of the coal pillar itself. While there is a significant amount of work done on floor stability associated with regular pillars, no work has been done so far on the stability of perimeter pillars. This paper reports the results of a comprehensive study that was conducted for the first time on floor stability during perimeter mining in the Illinois Basin mines. A special plate template, which mimicked a common perimeter pillar configuration was created to conduct in-situ bearing capacity tests at five mines in three states of the Basin. Additionally, because of the complex shape of pillars created in perimeter mining that defies any closed-form solution, floor bearing capacity was studied using three-dimensional nonlinear numerical modeling. Based on these in-situ and numerical studies, some guidelines are provided for perimeter pillar stability analysis.

Jan 1, 2009

By Eric S. Weiss, Deno M. Pappas, Timothy M. Barton

During the past few years, the Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) has been evaluating developments in sealant support systems from a ground control perspective. The proper selection and use of a sealant material can significantly enhance ground control which may result in a decrease in worker related injuries due to ground falls. The purpose of this paper is threefold: to briefly review the current state-of-the-art technology in shotcrete and membrane developments, to evaluate the preliminary findings of a long-term underground study of various types of sealant materials, and to examine installation practices that are critical for an effective sealant material. The underground study utilizes NIOSH’s Lake Lynn Laboratory Experimental Mine to evaluate the long-term performance of several types of shotcrete and membrane materials. Sealant performance to date have been evaluated on a regular basis over a two year period. Although the study is still ongoing, critical mining practices were identified that may seriously effect the bond of the sealant materials to the mine roof and rib; most notably, the importance of scaling and thorough cleaning of the rib prior to application. Also, results froman extensive series of Schmidt Hammer tests found that the shotcrete increased in strength by 70% during the humid summer months.

By Yoshiharu Tanaka, Toshiyuki Ichijo, Masaaki Yamamoto

We utilized electronic detonators (EDs) to investigate the effect of high detonator delay accuracy on overbreak, remaining rock damage, and surface smoothness, in comparison with that of long-period delay detonators (0.25 sec interval) PDs. The experiments were conducted in a deep mine, in a test site region composed of very hard granodiorite with a seismic wave velocity of about 6.0 km/see and a uniaxial compressive strength, uniaxial tensile strength, and Young's modulus of 300 MPa, 12 MPa, and 73 GPa, respectively. The blasting design was for a test tunnel excavation 8 m in cross section, with an advance per round of 2.5 m. Five rounds were performed, each with a large-hole cut and perimeter holes in a 0.4-m spacing charged with 20-mm-diameter water gel explosive to obtain low charge concentration. EDs were used in the holes on the perimeter of the right half, and PDs were used in all other holes.

Jan 1, 1995

By E. V. Lilford

The South African Minerals Development Act (?the Act?) has been promulgated and will come into full force and effect once it is gazetted. Thereafter, all Old Order mineral rights will have to be converted into New Order mineral rights within a 5-year period, probably by the end of 2008. The conversion of rights will be achieved only with the demonstrated inclusion of empowerment groups in the conversion applications. In addition to the Act, the first draft of the proposed Royalty Bill (?the Bill?) was released during the week beginning 17 March 2003. Comments on the Bill?s contents had to be submitted before 30 April 2003. The contents were to be considered in terms of applicability and acceptability to the South African minerals industry, where after proposed comments and suggested amendments were to be submitted to the relevant State Treasury office. Specifically referring to the Bill, the general response from the industry is one of concern. Since any royalty is tantamount to a tax, the general feeling is that the current mining taxation rates are already internationally competitive and to increase these effective rates, notably at differing rates depending on commodity type, will have an adverse impact on the South African mining industry. A number of these impacts can be mitigated to some degree, depending on the flexibility of the State to address the major concerns.

Jan 1, 2003

By Elisabeth Schmidt

The conventional Canadian oil sand processing, the Clark Rowe process, is associated with many risks for the environment and high energy costs. To recover the bitumen from the oil sand (tar sand), large quantities of water have to be heated up and mixed with caustic soda and the oil sand. During this process, tailings with stabilized clay colloids are formed and dumped in tailings ponds. To avoid these disadvantages, a new, non-aqueous extraction process is to be established. Organic solvents are used instead of water and caustic soda to mobilize the bitumen from the sand-clay mixture. Pressure filtration, washing and steam pressure filtration are part of the new concept. A mixture of organic solvents and the oil sand is first pressure filtrated in a nutsch filter until a saturation level of one is obtained. After the cake has been formed, the filter cake is washed with organic solvent to flush the bitumen loaded solvent out of the cake. The following steam pressure filtration mechanically and thermally removes the remaining volatile components of the solvents from the filter cake. The filtrates from the pressure filtration, the washing phase and partly from steam pressure filtration are subsequently thermally treated to recover the organic solvents and obtain a higher bitumen concentration in the mixture. This mixture is then lead to an upgrader to win synthetic crude oil (SCO). The recovery of bitumen in the conventional hot water extraction process based on the Clark Rowe process can, in highly optimized plants, achieve between 88 and 92 %. Variation of oil sand properties leads to an actual range of between 80 and 90 % of bitumen recovery. With the alternative process based on organic solvents, the bitumen recovery exceeds the recovery of the conventional process by up to 16 percentage points. The composition of the two organic solvents in the first step of forming a suspension with the oil sand is important. The aromatic component is crucial for liberating and solving the asphaltenes, which tend to flocculate. The order of the two components of organic solvents is also important in the washing step. The paraffinic component is essential to achieve successful steam pressure filtration with respect to fast steam breakthrough and a filter cake free from organic compounds, as a result of its lower boiling point. Keywords: oil sand, filtration, organic solvents, pressure filtration, steam pressure filtration, filter cake washing

Sep 1, 2012

By Geraldo Timotheo da Rocha

Nos últimos anos ocorreu uma deterioração considerável na qualidade química e granulométrica dos minérios de ferro utilizados na sinterização. Como resultado ficou limitada a utilização de silicatos de MgO na mistura, devido à elevação excessiva do teor de sílica no sínter, e as siderúrgicas voltaram a utilizar a dolomita como fonte de MgO. A utilização de pellet feed na mistura a sinterizar (natural ou moído) tem se apresentado como uma alternativa à elevação do teor de sílica na sinterização e a eventual redução na produtividade, compensada pela otimização das condições de misturamento. Testes em escala piloto indicam que a eventual redução na produtividade, decorrente da utilização do pellet feed, pode ser compensada pela utilização de olivina na mistura a sinterizar, em substituição à dolomita, com uma otimização do processo e da qualidade do sínter.

Aug 1, 2018

By Mick Fritz, Tom Treleaven

The success of any blast is dependent on the accuracy of the blast design and field controls placed at the shot location. The procedure by which the data is collected and analyzed is paramount to accomplishing the anticipated blast results. lf the geometry of the blast is not measured correctly, then the results will not meet expectations. Measuring the geometry and compensating for bole hole deviations is crucial not only to the lnitlal blast but also for any consecutive blasts. Excessive bore hole deviation can cancel any new technology in use. However the instruments and skills required solving this Issue are readily available.

Jan 1, 1998

By John Blackshaw

NEW sources of supply of tungsten concentrates became necessary when the flow from the Far East was blocked in 1942. In Canada, one source has been noted in the workings of the Hollinger mine at Timmins, Ontario. For many years, a small amount of scheelite had been removed with the gold ore, and an appreciable tonnage of scheelite still remained in the mine. At the request of the Dominion Government, a plant was built to recover this scheelite in the form of a concentrate that could be used by the alloy-steel industry without further preparation. The plant began operating early in March, 1942, and a small tonnage of ore, carrying scheelite and gold values, has been treated daily since then. The possibility of recovering the scheelite had been considered on several previous occasions. Each time the proposal had been given up because the total profits from the enterprise were estimated to be insufficient to repay the capital cost of building the recovery plant. At the time the plant was built, additional information had been gathered about the tonnage and grade of the scheelite ore in the mine, and several thousand tons of ore grading higher than 0. 25 per cent WO3 (tungstic trioxide) were known to be available.

Jan 1, 1943

Validation and Application of Filtration Theory to Plate and Frame Pressure Filtration - From Laboratory to Full Scale

Sep 13, 2010

Novel flotation reagents were developed to improve the flotation of coarse particles. Laboratory tests conducted on an anthracite coal sample from Kyung-Dong Coal Company, Korea, showed that the reagents can successfully clean 2?3 mm top-size materials. Pilot-scale tests conducted on a 1.41 mm x0 coal gave substantially better results than those obtained using kerosene as collector. The pilot-scale test results were used to develop a flowsheet, in which the 1.41 mm x0 fraction is cleaned by flotation and the 4 x1.41 mm coal is cleaned by single-stage spirals. The performance of this circuit was compared with another flowsheet, in which the 0.5 mm x0coal is floated using the conventional flotation reagent, with the 4 x0.5 mm material being cleaned using two separate spiral circuits. The performance of the two flowsheets was compared by computer simulation. The results showed that the flowsheet consisting of the coarse particle flotation circuit can give substantially higher yield sat a given product grade. Keywords: coal flotation, coarse particle flotation, collector, spirals, computer simulation.

Jan 1, 2002

By T. Plikas, L. H. Gunnewiek, L. Oshinowo

"Electric furnace smelting is one of the principal unit operations for ferroalloy production, and increased process intensity, improved availability, minimal maintenance and a longer campaign life are common objectives for electric furnace operation in order to obtain favourable economics of production. Furnace designers have continued to develop innovative solutions, e.g., furnace cooling systems, that have allowed these objectives to be realised and CFD modelling plays a key role in the design process. Enhanced understanding of the energy transfer process in the furnace and the ability to develop, evaluate and optimize components of the crucible design to match process requirements are the key motivators for modelling.This paper provides an overview of recent applications of CFD to the design of electric furnaces. The aim is to illustrate what can be done, and identify areas where further work is needed in this field. Examples include furnace bath simulation, crucible cooling system design, taphole design, baking of Soderberg electrodes, off-gas systems, and fume control and building ventilation. It is argued that the trend is for numerical models to become more encompassing while at the same time more accessible, and therefore further improvements in furnace design will be realised with continued and well validated modelling efforts.IntroductionOne of the main processing steps in ferroalloy production is the smelting of ore in electric furnaces. The three-electrode, AC submerged arc furnace is most prevalent method for smelting in the industry, with shielded-arc and DC plasma arc furnaces achieving limited application (1,2). Commercial furnaces range in size from a few megawatts to more than eighty megawatts of supplied power, and operate with the objective of maximising the return on capital invested. Maximising productivity and energy efficiency are two pathways to achieving this objective, through process intensification, increased availability, minimal maintenance, and increased campaign life for the furnace and associated equipment. Concurrently, the need to reduce the environmental impact of metal production by controlling the emission of particulate emissions, greenhouse gases, and other harmful by-products must also be met."

Jan 1, 2004

By R. W. Waytulonis

This paper is an update of the activities of the U.S. Bureau of Mines, other government agencies, and the automotive and truck industry concerning diesel emission control. Enacted and proposed regulations from the U.S. Mine Safety and Health Administration (MSHA) and developments in diesel emission control are presented in terms of their impact on underground coal, metal, and nonmetal mines. Mine air quality regulations proposed by MSHA may require the underground mining industry to comply with new standards. Some mines may be required to take additional actions to meet new diesel particulate and lower nitrogen dioxide exposure standards; however, the mining industry is in a position to benefit from emission controls developed for the on-highway diesel engine market. The U.S. Environmental Protection Agency (EPA) has enacted regulations to reduce emissions from on-highway diesel trucks and buses. Engine manufacturers have responded by developing cleaner burning engines. Fuel producers have responded by providing cleaner burning reformulated diesel fuel, and exhaust aftertreatment devices have been developed to provide additional emissions reductions. Bureau research and development projects seek to determine the advantages of using modern engines and fuels, and to evaluate the efficacy of new exhaust control devices on mining machines. It appears that the diesel engine will continue to be a practical power source for use in confined environments because no other available power source is as mobile and efficient.

Jan 1, 1993

By Richard A. Bideaux

With both unit costs per meter and average depth of drilling constantly increasing, there is a strong incentive to maximize the information acquired from drill holes, and then to make this information accessible to the geological staff. The larger the drilling project, the more advantageous computerization of data is over manual methods. The conversion to computer-readable form and the verification of large amounts of drill-hole data can be a substantial data processing task, but once accomplished, the benefits in increased accuracy and speed of interpretation will compensate for the time and effort spent in the work. For an exploration project progressing towards a preliminary feasibility study, about half of both the time and costs for all computer work of the entire feasibility study are devoted to drill-hole data base organization, and maintenance. Once drill-hole results are quantified and verified to be correct, they are immediately accessible and are not subject to further transcription or reinterpretation of errors. To obtain maximum benefits from computer utilization in this area, the drill-hole data base should be set up along with availability of the first data. For some companies, this may initially comprise a large number of purely speculative drill holes on a spacing of perhaps 1 or 2 km. Although few of these drill holes may encounter economic material, thought should be given, at this time, to the variables which will be logged when such material is found. In this way, it should be possible to set up a consistent format into which all future drill-hole information will readily be accommodated. This format may even be carried over into the data base requirements for an operating property.

Jan 1, 1979

By W. Burger

Mechanical excavation methods can significantly improve excavation performance and labor safety compared to drill and blast operations. Herrenknecht has developed a mechanized shaft sinking method for soft and medium strength rock. This system combines innovative technologies which allow simultaneous excavation, removal of cut material and the installation of rock support. This Shaft Boring Roadheader ?SBR? is flexible in diameter and can be used in shafts with changing diameters and different shaft support requirements for depth up to 2,000 m. During regular excavation personnel are not required to access or work on the shaft bench. The boom used to cut the shaft profile is based on roadheader technology.

Jan 1, 2012

By J. -H. Wu, S. Nishiyama, Y. Ohnishi

The behaviors and stress distributions of the inclined jointed rock masses with different dip angles obtained from DDA are compared to the results of laboratory tests. By calculating the block stress distributions, it is confirmed that DDA can reproduce the arching around the trap door when lowering the trap door. The shapes of arching change with the angles of inclined layers. In addition, the earth pressures acting on the trap door shows non-symmetrical distributions when the layers are not horizontal. The stress concentration occurs in one side of the rock masses close to the trap door. Furthermore, the surface settlements are also related to the inclined angle, and the loosening zone in rock masses can be different from Terzghi’s theory [1]. Since, simulations have good agreements with the laboratory test , it demonstrates the applicability of DDA to explain the mechanical behaviors of tunnel, such as arching phenomenon, non-symmetrical earth pressure distributions acting on the trap door, and the surface settlement profile in the jointed rock masses. Dans cet article est décrite l’étude numérique du perçage d’un tunnel dans un massif de couches rocheuses jointes inclinées. La simulation à l’aide de l’Analyse de Déformation Discontinue (DDA), en faisant varier l’angle d’inclinaison des couches de roche, nous apporte des résultats en termes de distributions de contraintes et de comportement des couches, résultats qui sont ensuite comparés avec des résultats de tests en laboratoire. Les résultats confirment le fait que la DDA est capable de reproduire le phénomène d’arcage autour de la trappe lorsque la trappe s’abaisse. Les formes d’arcage varient selon l’angle d’inclinaison des couches de roche. Par ailleurs, lorsque les couches ne sont pas horizontales, la distribution de pression agissant sur la trappe est assymmétrique. La concentration de contraintes se produit du coté proche de la trappe. De plus, les tassements de surface dépendent eux aussi de l’angle d’inclinaison. En conséquence, les résultats de simulation sont en accord avec les tests en laboratoire, ce qui prouve que la DDA permet d’expliquer des comportements mécaniques du tunnel tels que l’arcage, les distributions assymmétiques de pression du sol sur la trappe, ainsi que le profil du tassement de surface dans la masse de roches jointes. Dieser Beitrag beschreibt eine numerische Studie über Tunnel im geklüftetem Fels. Das Verhalten und die Druckverteilungen in den unterschiedlich geneigten und geklüfteten Felsenmassen wird mit Hilfe des Discontinuous Deformation Analysis Programms (DDA) simuliert, und mit Laborversuchen verglichen. Die Resultate bestätigen, dass DDA der Gewölbewirkung im „Trapdoor“ Experiment gut reproduzieren kann. Die Form des Gewölbes, ändert sich mit unterschiedlichen Neigungswinkeln der Schichten. Bei geneigten Schichten entstehen unsymmetrische Druckverteilungen. Auch die Oberflächenabsenkung ist von dem Neigungswinkel abhängig. Die gute Übereinstimmung der Simulationen mit den Laborversuchen zeigt, dass die DDA-Methode gut geeignet ist, um das mechanische Verhalten von Tunneln, wie z.B. den Effekt der Gewölbewirkung, die unsymmetrischen Druckverteilungen bei geneigten Schichten, oder die Oberflächenabsenkung in geklüfteten Felsenmassen, zu erklären.

Jan 1, 2003

By Kourosh Shahriar

The occurrence of rock falls in underground coal mines entails detrimental effects as fatal or non-fatal injuries on workers, stoppages in mining operations and breakdown of equipment. In this paper, a risk assessment approach on the basis of a decision analysis trend is employed in order to assess the possibility of and manage roof falls. Risk is then assessed by determination of likelihood of occurrence and the cost of consequences (outcomes). In this regard, collected real roof fall data from Tabas and Kerman coal regions comprising of several underground coal mines are used. It is concluded that the annual accidents due to the roof falls occurrence in the all investigated mines are so high that it is economically feasible to improve the support systems and to implement a suitable educational program as well as an accurate supervision and other elements of safety management.

Jan 1, 2009