Search Documents

By Sushil Bhandari, S. S. Rathore

Controlled drilling and blasting continue to be an important method of block production and for block splitting. Drill and blast technique has disadvantage that sometimes, it produces cracks in uncontrolled manner and also produces micro cracks in the block as well as in remaining rock, if not carefully carried out. Recovery by this method is low compared to other methods. Therefore, attempts have continued to develop controlled growth of crack in desired direction. In this paper a series of tests are described using detonating fuse in marble. Economics of different methods is also compared. In comparison to conventional use when holes are lined with inexpensive cardboard or plastic liners with a slit, the cost and damage is the least and development of crack is in desired direction.

Jan 1, 2002

New Bio-Adsorber with Activated Carbon and Nano Tube Carbon for Separation of Nickel and Cadmium

Sep 13, 2010

By Rennie Kaunda, David Streeter, John Kemeny

This paper describes a field/laboratory study that was conducted in cooperation with a mine in Arizona. The primary purpose of the study was to investigate the effect of blasting energy on the crushability and grindability of the post-blast rock fragments. The crushability and grindability of the rock fragments were evaluated through laboratory comminution tests. A secondary purpose of the study was to investigate different laboratory methods for estimating the comminution properties of the rock fragments. In particular, a number of standard rock mechanics tests were conducted and compared with the comminution test results. Finally, the study was used to evaluate new technologies for estimating insitu rock mass strength and for assessing post-blast fragmentation. To estimate in-situ rock mass strength, the specific energy of drilling (SE) was calculated during blast hole drilling utilizing a continuous drill monitoring system. Post-blast fragmentation was estimated using the Split image processing system. Results from the study support the idea that increases in blast energy can enhance crushing and grinding. Also, several simple rock mechanics tests were found to correlate well with the results from standard comminution tests, which could prove to be useful in practice.

Jan 1, 2003

Mineralisation was identified at Gladstone Hill as far back as the late 1870's û early 1880's, shortly after the initial discovery of Martha Hill. Indeed, early recovery problems from the Martha Hill mineralisation led to the preferred development of are bodies within what is now the Union Hill Joint Venture tenement; ore bodies such as Silverton, Amaranth, Union to name a few. Work at Gladstone Hill is carried under the Union Hill Joint Venture, a 50:50 joint venture between Auag Resources Ltd - manager (a fully owned subsidiary of Otter Gold Mines Ltd) and Welcome Gold Mines Ltd (a fully owned subsidiary of the Normandy Group). The joint venture participants also operate the adjacent Martha Hill operation. Mineralisation of Gladstone Hill, as with mineralisation at the adjacent Martha Hill, has been interpreted as a low sulphidation epithermal Ag-Au system hosted within hydrothermally altered andesites of the lower Coromandel Group. Drilling in recent years has successfully identified extensive mineralisation associated with the Gladstone vein set and the more recently identified high grade Moonlight Lode. Veining ranges in character from thin stock works to broader lode-style banded chalcedonic to cherty quartz. Visible gold is rare, with mineralisation generally associated with very fine-grained pyrite, arsenopyrite and minor electrum. The potential for the Gladstone Hill area is yet to be clearly defined as drilling to date has yet to close off mineralisation both along strike and down dip. If further drilling is successful, the joint venture partners believe Gladstone Hill could contribute significantly to the economic future of current operations.

Jan 1, 1999

By T. F. J. Hälbich

Namakwa Sands aims to conserve environmental resources and prevent or minimize environmental impacts from its operations. The challenge faced by Namakwa Sands is the rehabilitation of the arid winter rainfall Strandveld and lowland Succulent Karoo vegetation zones affected by its mining activities. Extensive experimentation with different rehabilitation methods resulted in the development of an effective rehabilitation programme. The use of topsoil as a seed bank and shade-cloth as windbreaks have significantly aided the rehabilitation process. The aim of the programme is to stabilize the soil environment so as to allow the germination and development of the local plant species. The ability to control wind erosion is critical to the success of the rehabilitation effort. A programme of biodiversity audits has been started to measure the recovery of plant species in the rehabilitated area. The principle of continuous improvement, coupled to site-specific rehabilitation studies, is applied to enhance the rehabilitation programme.

Jan 1, 2003

By T. M. Ruff

A prototype mucking machine designed to operate in narrow-vein stopes was developed by Foster- Miller, Inc., Waltham, MA, under contract with the U.S. Bureau of Mines. The machine, called a compact loader-trammer, or minimucker, was designed to replace slusher muckers in narrow-vein underground mines. The minimucker is a six-wheel-drive, skid-steered, load-haul-dump (LHD) machine that loads muck at the front with a novel slide-bucket system and ejects it out the rear so that the machine does not have to be turned around. To correct deficiencies of the tether-remote-control system, a computer-based, radio-remote-control system was retrofitted to the minimucker. Initial tests indicated a need to assist the operator in guiding the machine in narrow stopes. An automatic guidance system that used ultrasonic ranging sensors and a wall-following algorithm was installed. Additional tests in a simulated test stope showed that these changes improved the operation of the minimucker. The design and functions of the minimucker and its computer-based, remote-control system are reviewed, and an ultrasonic-sensor-based guidance system is described.

Jan 1, 1992

By G. Noce

The ever more present necessity for greater precision in foundation structures on vertical piles subject to horizontal forces applied to the heads, in the light of of the latest knowledge about the elastic-plastic behaviour of the soil has led to the use of numerical calculation for the formulation of a general resolution method for the problem. The calculation method that will be set out, applicable to piles with inertia moments variable discreetly along their axes is especially useful when studying steel structures for medium and large tonnage vessels for which the metal piles are often constructed for the assembly of section of equal external diameter but different thickness and therefore different inertia moments. Two examples are given of constructions whose foundations have been projected with these calculation tools, one in the railway sector (foundation pile for the river Nera viaduct - Italy) important for the limitation of horizontal relative deck displacement, the other maritime (Dolphins of the petroleum pier of the port of Bandar Abbas - Iran).

Jan 1, 1989

By Mohamed Ourriban, Yongjun Peng, Qi Liu, Denis Cotnoir

"In the flotation of fine particles, there are two difficulties in general: low recovery of valuable minerals and high recovery of gangue minerals. The low recovery of fine valuable minerals is attributed to low bubble-particle collision and attachment efficiencies, while high recovery of fine gangue minerals is attributed to mechanical entrainment through water films between gas bubbles. Over the last five years COREM has been actively developing fine particle flotation techniques with the objective of improving fine particle flotation separation efficiencies.The fine particle flotation techniques with both generation of micro bubbles and enlargement of sizes of fine particles have been developed to increase bubble-particle collision efficiency. For oxidized fine sulphide minerals, both physical and chemical techniques have been developed to modify the hydrophilic surfaces and therefore increase bubble-particle attachment efficiency. To reduce mechanical entrainment of fine gangue minerals, a new approach, polymeric depression and flocculation, has been developed. By selecting the high molecular weight polymeric depressants to make fine gangue minerals hydrophilic and also enlarge their sizes, entrainment can be minimized. By combining these techniques, we are able to improve both flotation recovery and selectivity in some fine ore flotation systems.INTRODUCTIONWith depleting mineral resources and their declining grades, ores leaving grinding circuit for froth flotation are becoming increasingly finer to achieve mineral liberation. Together with the increasing demand for minerals, ever-increasing tonnages of fines are being produced. Therefore, flotation of fine particles is an immense challenge to be tackled by researchers all over the world today."

Jan 1, 2006

By J. C. Martin

Stmplified equations are developed for the flow of fluids in gas drive reservoirs in which the effects of gravity can be neglected. The results show that the pressure distribution is governed by a nonlinear heat flow type of equation, and the saturation distributions are related to the pressure by the same equations QS those developed by Muskat for the average pressure and saturations in gas drive reservoirs. Unrler certain conditions the equation for the pressure can be approximated by the linear form of the heat flow equatlon. This equation tk analogous to the equation for the pressure in single-phase compressible flow The analysis reveals that the equation for the pressure in n~ultiphase flows can be obtained directly from the equation for the pressure in slngle-phase flows by simply replacing the single-phase compressibility by the total compressibility and the single-phase mobility by the sum of the mobilities of all the fluids present. Perrine's method of pressure buildup analysis for multiphme flows is based on these same substitutions. Thus, the development presented in this paper constitutes a theoretical justification for Perrine's method of pressure buildup analysis. One of the most difficult problems associated with the production of oil is the determination of the flow of the fluids within the reservoirs. One purpose of this paper is to present the development of simplified equations for the flow in gas drive reservoirs. The other purpose is to present some of the needed theoretical foundation for the methods currently being used in the analysis of multiphase pressure buildup data. The analysis presented in this paper makes use of a partial linearization of the equations governing multiphase flows. It is felt that the process of linearizing or partially linearizing the nonlinear equations of multiphase flows can lead to useful results since this process has proved extremely valuable in the study of other fields of science and engineering where nonlinear equations are encountered. Pressure buildup data of shut-in wells have been used for many years to estimate the static reservoir pressure. These data have also been used in studying the aver- age permeability both away from and close to the well-bores. The majority of the buildup data are obtained from wells producing two or three fluids. As yet the theoretical foundations for the methods of buildup analysis used in connection with rnultiphase buildup data have not been established. A number of methods of analysis of pressure buildup data have been developed." Most of these methods apply only to single-phase flows, and almost all of the theoretical analysis is confined to single-phase flows. Perrine' developed a method of analysis for rnultiphase flows from the method for single-phase flows of Miller, Dyes, and Hutchinson.' He did this by simply replacing the single-phase compressibility by the multiphase compressibility and replacing the single-phase mobility by the sum of the mobilities of the fluids in the rnultiphase flows. Obviously, such a procedure lacks a certain amount of theoretical justification, and such practices can lead to erroneous results. Fortunately, Perrine's results have a theoretical justification, and this justification is presented in the following discussion. It is assumed that gravitational effects and the cornpressibility of the rock can be neglected. Under these assumptions the equations governing the simultaneous flow of gas, oil and water in porous media areo* The preceding equations can be expanded into the following expressions.

By Thomas Barczak

A cooperative study was conducted with Emerald Coal Resources, L.P., an affiliate of Foundation Coal Corporation, and the National Institute for Occupational Safety and Health (NIOSH) to evaluate the effectiveness of (partially) pre-driven longwall recovery rooms supported with pumpable roof supports. This paper evaluates the load transfer mechanics associated with the advancement of the longwall face into the pre-driven recovery room and the widening of the room to recover the longwall shields. The results show that the yielding of the panel fender produced uncontrollable convergence that caused yielding of the shields and stiff pumpable roof supports when the face was approximately 10 ft from the recovery room. The shields continued to yield until the face advanced into the recovery room. Convergence in the pre-driven recovery room typically reached 6-8 in once the pumpable supports yielded and shed load through a declining residual load capacity prior to being cut out by the longwall shearer. Roof deformations occurred beyond the 32-ft horizon with total deformation ranging from 2 to 4 in, indicating that standing support was necessary to help control the span as the longwall face advanced into the pre-driven recovery room. Stability improved as the pumpable supports were cut out, thereby reducing the span between the shields and the outby pillars. In the end, the shields were successfully recovered under stable ground conditions. However, a disconcerting discovery was the load shedding of the outby pillars as the recovery room was mined into. It is postulated that this may be due to the progression of the rear ?abutment? moving toward the recovery room as the panel fender and standing support in the recovery room yield and shed load. This behavior was not expected with a relatively narrow room that is fully supported with standing support. If this mechanism is indeed occurring, the width of the room and performance of the standing support becomes even more critical. Premature failure of the support can lead to excessive convergence on the shield line that cannot be controlled even with modern shields, resulting in roof instabilities that can lead to catastrophic results.

Jan 1, 2007

By A. Normanton, B. Harris, V. Ludlow, S. Riaz

Why does a continuous casting mould powder, which works successfully on a particular caster with respect to semi quality, fail to perform on a caster of a similar design utilizing liquid steel from a similar route for an identical product without some tuning of its make-up and composition? In casting sequences of the same steel grade, why do some apparent random heats produce poor surface quality with respect to cracking when otherwise good surface quality is realized? The answer to these questions lies in the interaction of the mould powder, the casting hardware, and the casting process variables. Using, as examples, data collected from within Corus UK and during collaborative work on the assessment of mould powder performance and its effects on surface quality, the interaction of the mould powder, the casting hardware and the casting process variables is explored. The steelmaking route and its associated alumina load, unexpected changes to slag chemistry, infiltration of the slag into the mould strand gap, and the nature of the slag film are all shown to affect powder performance. Keywords: continuous casting, mould powders, alumina, slag films

Jan 1, 2004

By Karen Mikkola, Gerald Luttrell, Jaisen Kohmuench, Glen Oswald, Michael Mankosa, Tracy Westerfield

Hydraulic separators are commonly used for particle size classification and gravity concentration of minerals and coal. Unfortunately, the efficiency of these processes can be quite low due to poor equipment design and variations in feed consistency. To help alleviate these problems, an industry-driven R&D program has been undertaken to develop a new generation of hydraulic separators that are more efficient and less costly to operate and maintain. Two of the most promising technologies, the CrossFlow and HydroFloat separators, have now been tested at industrial sites. The data obtained from these sites have been used to illustrate the potential performance improvements that can be realized through the application of these high-efficiency separators.

Jan 1, 2005

By A. Holeyman

The displacement compaction piles described in the paper are installed using a heavy casing or tube and an internal drop hammer. The casing which initially is closed at the bottom by a sand plug displaces the surrounding soil during the driving. Additional sand is rammed down through the casing during the extraction of the casing. The applications and limitations of the method are reviewed in the paper. The importance of checking the sand compaction piles during and after the installation is stressed. Indications of the compaction of the surrounding soil during the driving can be obtained by comparing the initial and the redriving logs of the casing as well as from the volume of sand added. A method to estimate the increase of the mean cone resistance as measured by CPT tests in sandy and silty soils is presented. The governing parameters are the volume of the added sand, the granulometric index and the initial cone resistance.

Jan 1, 2010

The New Technology of Enrichment of a Fine Low-Grade Tungsten from Complex Multi-Metallic Ore

Sep 13, 2010

By V. Kecojevic

Environmental and economic costs related to equipment fuel consumption and carbon dioxide (CO2) emission present a substantial challenge to the mining industry. Haul trucks are an integral part of the overall surface mining system and they consume a substantial quantity of fuel. Consequently, they produce a significant amount of CO2. The objective of this research is to (i) establish a mathematical relationship among a truck?s fuel consumption, power and engine load factors and (ii) determine the amount of a truck?s CO2 emission and the associated cost that may arise from potential CO2 legislation. In order to achieve these objectives we have considered original equipment manufacturer (OEM) haul trucks, commonly used in surface mining operations. The research presented here may be used by mining professionals to help determine the cost and environmental burden of the trucks? application, and efficiently manage energy consumption.

Jan 1, 2011

In recent years, Computational Fluid Dynamics, CFD, has been commonly utilized in the mining industry to model the fluid flow behavior in underground mine workings. This paper uses CFD modeling to simulate the airflow behavior in underground crosscut regions, where brattice sails are used to direct the airflow into these regions. Brattice sails are cost effective ventilation control devices for temporary or permanent use in underground mining. They can be used to deflect air into the unventilated areas such as crosscut regions. Their design and installation is a fundamental issue for maintaining a sufficient supply of fresh air and achieving effective air circulation and contaminant removal. At the same time, they should have little impact on the mine ventilation system. This paper presents the results of a two-dimensional CFD model, which examines the effects of brattice length on fluid flow behavior in the crosscut regions. The results of this study will assist in understanding the ventilation air behavior and in determining the optimum size of brattice curtain (sails), which provide a highly effective contaminant removal from the unventilated mine areas. This, in turn, helps the mine ventilation designers to meet the mine safety requirements.

Jan 1, 2009

By Roman Y. Poderny, Vladimir V. Rjevskii

In the USSR, the Moscow Institute of Radio Electronics tronics and Mining Electro-Mechanics (MIRGEM) has started what it hopes will become a nationwide movement to educate mining students in the precise specialties that industry has come to require. Courses for mining engineers, the MIRGEM faculty proposes, should dovetail as exactly as possible with specific jobs available in the mining profession. Acting upon this thesis, MIRGEM revised its own curriculum in 1962 and has since presented an over-all plan for Soviet mining education before two mining school conferences as well as the Ministry of Higher Education and a number of major Soviet industrial ministries. The plan was universally approved with some suggested revisions. SOVIET MINING EDUCATION TODAY At present, mining education in the Soviet Union covers the exploitation of solid minerals and raw materials, including coal as well as ferrous and nonferrous metals. The extraction, storage, and refining of oil and gas is treated as a separate discipline. In all, there are 33 Soviet universities and institutes that train mining engineers for careers in the industrial, research and educational fields.

Jan 9, 1966

By W. L. Jacobsen, T. L. Dyer

Cortez Gold Mines completed a feasibility study for a new openpit gold mine in north central Nevada. The production schedule calls for a peak in material movement. This schedule is based on current operational efficiencies and equipment parameters observed at the company’s existing openpit operation. To mitigate risks of over/under predicting production, simulation modeling was used to validate the loading and haulage requirements during the peak production period. The advantage of simulation is the ability to provide a realistic model of a mining operation based on scheduled and unscheduled random events during the period under analysis.

Jan 1, 2007

P. H. Dudley, Yew York, N. Y. (communication to the Secretary*) :—The characteristics of Professor Home's metallurgical papers are, that he is able, from the mass of confusing evidence on the subject, to make an analysis and present hypothetical and essential principles in concrete form for consideration and discussion. I can appreciate, from the practical side of the subject, the labor of collecting and investigating the data which was essential to prepare the paper. Much of it necessarily came from material of preceding years of manufacture in which time was allowed for chemical reactions of the re-carburizer, and for the elimination of the oxidation-products before teeming the ingots. This practice gave a favorable time-element to free the metal from slag and other impurities— a requisite condition for the production of sound steel in the ingots. But, in allowing them to become cold before they were charged into the furnace, a subsequent time-element entered as a detrimental factor in the development of the pipe or shrinkage-cavities, which gave an ingot-structure deficient in soundness, at least in the upper portion. (The term slag is used in a general rather than in a strictly technical sense.) Traces of manganese sulphide are often associated with manganese silicates in the same thread or seam, and at other places they are separate and distinct. Interpretations from material thus manufactured must be made with due allowances for the methods of fabrication and the requirements of service. The only way we now have to estimate what the degree of soundness of the ingot-structure was, in the early foreign and American manufacture of steel rails, is by examination of the worn and failed material after years of service. We must remember also that the poorest material was long since consigned to the scrap-heap without any full record of its history. The rails from a given ingot cannot now be identified ; and in many

Jan 1, 1909

By Keith A. Heasley

Exactly 25 years ago this month (August 12, 1981), IBM introduced the ?Personnel Computer? with a 16 bit operating system called MS-DOS 1.0. Since then, Moore?s Law, which essentially states that computer capability will doubled every 18 months, has been fully evident in the computer industry. As computers have advanced from main frames to initial personnel computers to the powerful graphical workstations of today, numerical modeling for ground control in mining has followed closely behind. Twenty five years ago, many numerical methods for solving ground control problems were little more than equations on a piece of paper. In the intervening years, these numerical models have grown from initial trial programs to highly-complex computational systems with numerous capabilities for different material behavior, failure criteria, gridding methods, discontinuities, etc. In some instances, the capability of the programs has quickly outstripped the geo-technical modeler?s ability to get accurate, realistic input and boundary conditions. This paper will look at: how numerical models have evolved in the last 25 years, how the models have been applied to ground control problems in that time period, and where numerical modeling is headed in the immediate future.

Jan 1, 2006