Search Documents

By M J. Begbie, K B. Sporle

The Golden Cross low sulfidation epithermal deposit produced approximately 750,000 ounces of Au from two ore zones: the underground Empire Vein System and the open pit stockwork. The Empire Vein System has at least eight stages of vein formation: (1) sulfide veins, (2) black veins, (3) massive veins, (4) banded veins, (5) thin white veins, (6) crumbly veins, (7) massive/platy calcite veins, and (8) flattened rhomb calcite veins. Gold mineralisation occurred relatively early in the lifetime of the system, dominantly during 2 through 4. The late calcite veins (7 and 8) and early sulfide veins (1) are barren. The vein system formed in a dominantly extensional environment, though some compressional faulting may have also existed during vein formation. There is no evidence for significant strike-slip faulting during vein formation, highlighting the fact that explorationists should pursue on-site structural patterns rather than fashionable models.

Jan 1, 1998

By Véronique Falmagne

The mining sequence at Noranda?s Bell-Allard mine calls for two mining fronts retreating toward a central pillar known as the Retreat Zone between pyramids A and C. It is clear from numerical modeling and rock mass characterization that the induced stress level in the pillar will exceed the rock mass capacity. A mining plan was developed including the re-dimensioniong of stopes in the Retreat Zone, additional ground support and instrumentation in order to ensure the safety of the workforce and to maximize ore recovery while minimizing production delays. The mining strategy consists in allowing the rock mass to fracture and fail progressively while maintaining control of the existing openings with the appropriate support. A systematic analysis of rockbursting and caving hazards was conducted for all accesses and stopes in order to plan ground support and instrumentation needs.

May 1, 2003

By A. Robles-Vega

In recent years, tellurium has been extensively used in the manufacture of semiconductor materials. For this type of application, high-purity tellurium is required. Selenium, lead and silicon are usually the main impurities in tellurium. During the electrolytic refining of copper, tellurium gold and silver are collected in the anode slimes. A pyrometallurgical treatment is used to recover gold and silver from the decopperized anode slimes whereas tellurium is oxidized and skimmed off from the refining furnace as a Na2CO3-based slag. In the slag, tellurium is present as sodium tellurite (Na2TeO3), which is further water-leached from the slag. The first step in the conventional process for tellurium recovery consists of the precipitation of the tellurium contained in the leaching solution as tellurium dioxide (TeO2). The solid TeO2 is then dissolved under acidic conditions for its further reduction with sulfur dioxide gas (SO2). In this paper, an alternative route for tellurium production is presented in which a sodium tellurate [Na2TeO4] intermediate is obtained by oxidation of the sodium tellurite in an alkaline solution following the water leaching step. Sodium tellurate is then dissolved in acid media and high-purity tellurium is obtained by reduction with SO2 gas. Experimental tests under laboratory conditions indicate that the novel process yields higher precipitation selectivity for tellurium than the conventional process. A comparison of its efficiency concerning impurities co-precipitation with respect to the conventional process is discussed.

Jan 1, 2009

By J P. Clark

Industrial minerals contribute about 50% of the NZ$1.2 billion generated annually by the minerals industry in New Zealand. The value is supplemented by a further NZ$500 million of minerals imported to supply our vital agricultural and industrial activity. As globalisation of the world's economy precedes, sources of minerals are being processed by fewer companies giving an ever-increasing control over global markets. If only to protect its primary production New Zealand needs to aggressively develop its mineral resources. The successful development of a deposit requires identification of the preferred market. While low-value aggregates dominate New Zealand industrial mineral production it is more specialised minerals supplied to the manufacturing and industrial sectors that provide more value per tonne. Minerals that have highly desirable intrinsic properties, or through value-added processing provide desirable properties, have the ability to fill niche markets both locally and overseas. Research and development towards enhancement or creation of desirable mineral properties could benefit New Zealand with both increased mineral potential and export of technological information. But, it is nearly always the market not the resource that dictates the viability of an industrial mineral and, with the globalisation of industrial mineral markets resulting in fewer but larger companies, any supplier must be ready to explore niche markets in order to compete on a more global basis.

Jan 1, 2000

By Kenneth B. Higbie

METALLURGICAL ACTIVITY in 1963 was again dominated by the insatiate demands of research and development conducted in conjunction with the nation's defense and aerospace programs. An increasing effort was noticeable throughout the year, however, to apply to the commercial field many of the processes and techniques that have been developed by government-sponsored research. Particularly effective has been the Industrial Applications Program of the National Aeronautic and Space Agency through which many of the technological advancements made during the course of NASA research and development have been published and released to the public. POWDER TECHNOLOGY Powder metallurgy techniques for fabricating metals, not long ago declared outmoded because of improved casting and shaping methods, have since made an astonishing comeback. Traditionally mechanical pressing of powder shapes has been employed when melting and casting was difficult or impossible, when phase relationships needed to be sidestepped, or when machining costs could be avoided. Hence, it has long been used for producing relatively small special shapes of high-melting metals and alloys. Small iron parts produced with a punch and die have been common for many years, but powder metallurgy techniques are now applicable to a wide range of materials and items. Hard-to-handle materials including refractory metals and their alloys are now rolled, forged, or extruded from billets made by sintering isostatically compacted powders. The major element of the powder metallurgy industry still comprises iron shapes, however, and two-thirds of the annual 100,000 tons of powder metallurgy products are made of iron. The largest single user of powder-forming techniques is the automobile industry which currently consumes 14,000 to 16,000 tons of iron powder per year. A typical 1963 model auto contained more than 100 pressed powder parts (e.g., transmission gears, timing gears, sprockets, ball joint suspensions) totaling 5 to 7 pounds per car. Some of these powders are used in self-lubricating parts of porous copper and copper alloys containing as much as 20 volume-percent lubricating oil. The expanded use of powder techniques, coupled with

Jan 1, 1964

Published experimental data on thermodynamic behaviour of cobalt-containing slags have been reviewed and used in validating a recently developed thermodynamic model. The results from the exercise show that the model provides a reasonably good description of behaviour of cobalt in multi-component slag systems. The models for cobalt containing slags, matte and oxide solid solution phases were incorporated into CSIRO?s multi-phase equilibrium (MPE) package, which was used to calculate the equilibrium distribution of cobalt between matte and slag phases under various conditions. The results agreed well with the experimental data. Furthermore, the good agreement between the calculation and the plant data indicates that the operating conditions of industrial smelting and converting processes are close to equilibrium. Two diagrams showing the effects of slag chemistry and SO2and O2partial pressures on the distribution of cobalt between phases were generated for conditions similar to smelting and converting processes. These diagrams provide some useful guidelines for developing new strategies to improve cobalt recovery.

Jan 1, 2004

By Bill Stormes

This paper will discuss implementation of the Hilti OneStep rock anchor technology to improve face bolting operations during the May 2008 longwall move; increase rock anchor installation capacity; and improve safety by reducing employee exposure periods by utilizing the Hilti OneStep rock anchors.

Jan 1, 2008

By S. Uddin

An integrated device has been developed to measure sedimentation potential, conductivity and pH simultaneously of particulate systems. Maxwell?s model was used to calculate volume fraction of solid from the conductivity data. In this approach, all system variables are known and zeta potential can be calculated from Smoluchowski?s equation. The technique is validated by comparing zeta potential vs. pH for alumina and silica suspensions with electrophoresis measurements. The technique was extended to mixed alumina/silica systems. Sufficient column height along with size difference between the two minerals allowed gravity fractionation during settling. Sedimentation potential measured over time identified the transition from one mineral to the next. Using XRD analysis the results supported the correlation between surface charge and sample composition. This is a step towards characterizing surface charge of mixed systems of interest in mineral processing.

Jan 1, 2010

By J. R. Goode

"Coarse ore sorting is here defined as the physical separation of a mixture of coarse (+3/8 inch) ore particles into two or more separate groups of total value greater than that of the unsorted ore. An ore will probably be sortable if the geology of the orebody and the mining practices employed meet conditions outlined in this paper.The paper points out how sorting can substantially reduce tonnage variable operating costs because sorting can double the mill head grade of amenable ores by rejecting waste rock from the mine output. The effect of sorting on ore reserves is outlined. It is also suggested that sorting is a low cost alternative to conventional expansion.The mode of operation of the Ore Sorters Kadel 13 Photometric and MK VI A Radiometric sorters is detailed. The report concludes with detailed descriptions of the photometric sorting plant operated by the Doornfontein Gold Mining Company is South Africa and the Radiometric Sorting Plant presently under construction at the Schwartzwalder mine of Cotter Corporation in Colorado."

Jan 1, 1975

By A. J. Monhemius

"The paper reviews the history of modern iron control processes in hydrometallurgy. Particular attention is paid to the processes developed in the 1960s by the electrolytic zinc industry for the removal of iron from zinc sulphate leach liquors - namely the Jarosite, Goethite and Hematite processes. Problems faced by the industry in the safe disposal of the iron residues produced by these processes are discussed. The lessons learnt over the past half century by the zinc industry are projected on to the current efforts to develop hydrometallurgical processes for the treatment of copper sulphide concentrates. It is argued that any attempt to create a “hydrometallurgical copper smelter” is doomed to ultimate failure, unless and until methods are developed that can recover iron from solution in a form that can be directly utilised by the steel or pigment industries.INTRODUCTIONYou suddenly realise that age is catching up with you and that technology is moving on apace when you are asked to talk about the history of a process or a technology that you’ve grown up with. Such was my reaction when, out of the blue, I received an email last year from the chairman of the CIM’s Historical Metallurgy Committee, asking me if I would give a talk on the early developments of iron control in hydrometallurgy. Once I’d got over the initial shock of realising that I had now become living history, I was of course flattered that the invitation was to give a talk at the prestigious IMPC, a conference series that has been going for as long as I have been in the business. That this particular IMPC was to include the 4th Symposium on Iron Control in Hydrometallurgy, made the invitation even more appealing and appropriate, because I was the co-chairman of the First Symposium on Iron Control, together with my old friend, John Dutrizac (known by many as Dr Jarosite), which was held 30 years ago in Toronto.first became involved with iron at the very start of my career in hydrometallurgy – the research topic for my Masters degree thesis at UBC, back in the mid 1960s, was “Reductive leaching of Goethite with SO2”. My thesis supervisor was the late Professor Ian Warren, who himself was a protégé of Professor Frank Forward, one of the founding fathers of modern hydrometallurgy. Little did I realise at that time, now 50 years ago, that the problem of iron and how to deal with it in hydrometallurgical processes would be a theme that followed me throughout much of my 40-year career in academia."

Jan 1, 2016

By Paulo Augusto Cota Leite

Os aços inoxidáveis martensíticos, em geral, aliam boas propriedades mecânicas e satisfatória resistência à corrosão, características associadas à possibilidade de realização de tratamentos térmicos de têmpera e revenimento. Nesse contexto, no presente trabalho foram avaliados os efeitos das condições desses tratamentos na microestrutura e nas propriedades mecânicas de um aço inoxidável martensítico de médio teor de carbono. Foram consideradas três temperaturas de aquecimento na têmpera e seis temperaturas de revenimento. A avaliação microestrutural foi realizada por meio de microscopia óptica e microscopia eletrônica de varredura. As propriedades mecânicas foram avaliadas por meio de ensaios de dureza. Foi observada a elevação na dureza do aço com o aumento da temperatura de aquecimento na têmpera, assim como a dissolução dos carbonetos presentes no material. No revenimento subsequente observou-se o aparecimento do pico de dureza referente ao endurecimento secundário a uma temperatura de 500°C.

Aug 17, 2017

By Marcel M. Djivre

Electromagnetic wire rope testing is the only practical non-destructive method to evaluate the current condition of wire ropes in general, and in the mining industry in particular. The method has been successfully used worldwide for decades. In mining it has considerably improved the safety of operations. Yet, problems persist. In particular both the Loss-of-Metallic-Area (LMA) readings, as well as the Local Fault (LF) readings, as obtained by different instrument operators, were found to be unacceptably diverse. Consequently, large sums have been spent internationally, as well as in Canada, comparing a whole range of these instruments in an effort to rate their performance. The published results clearly confirmed operational experience, namely that the LMA and LF readings were, indeed, unacceptably diverse. Excellent pertinent conclusions were also published. In Canada the authors? conclusion was that while the divergence in the LF signal based results could, possibly, be attributed to both hardware and human-error related factors, the LMA signal related quantitative uncertainties were human-error related. Consequently, much attention was paid in Canada to developing novel control methods, namely computerized ones to replace the more error-prone analogue ones. In addition new sensor-heads were developed, both for portable as well as for permanent installation with remote control operations. While these efforts were of considerable benefit, the situation must again be carefully reviewed with very special reference to deep-level mining, now of immediate concern in Canada as well. In this paper the authors supply an overview of the results obtained by three of the four major international projects referred to previously. Relevant conclusions/comments are also restated. Moreover, specific recommendations are put forward as to how current problems might best be remedied.

May 1, 2004

By T. M. Ruff, W. G. McCoy, M. J. Beus, S. Iverson, W. Hasz

Technology to enhance safety during mine hoisting has been developed by researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health. Assessment of current hoisting technology suggests that monitoring conveyance position and load directly from the skip or cage top offers several significant safety advantages. Wireless data transmission schemes and a package consisting of sensors, batteries, and a charger mounted on the wire rope and skip have been developed. A state-of-the-art automated hoisting test facility was constructed to test the concept in a controlled laboratory setting. Field tests in a fill-size shaft are underway.

By Keith A. Heasley, Frank E. Chase, Christopher Mark

Deep cover retreat mining (overburden in excess of 750 ft) is an important emerging issue which will intensify in the future as the more easily mined shallow seam reserves are depleted. Analysis of Mine Safety and Health Administration (MSHA) statistics indicates that deep cover pillar recovery accounts for a disproportionate share of the underground coal mine roof/rib fall fatalities and injuries. Past research has shown that previously recommended Analysis of Retreat Mining Pillar Stability (ARMPS) stability factors (SF’s) may be excessive for deep cover pillar design. The objectives of this study were to evaluate the various methods and strategies by which panels, production pillars and barrier pillars are developed and extracted under deep cover, and to develop appropriate design guidelines. In the course of the research, 29 mines in 7 states were investigated to collect panel design case histories. At each mine site, underground geotechnical data were collected on the pillar line in order to document roof rock, coalbed and floor conditions. The analyses indicated that squeezes were the most likely failure mode where the depth was less than 1,250 ft, but bumps predominated in the deeper cover cases. Immediate roof rock quality, the ARMPS SF’s, and barrier pillar stability factors were all found to be important parameters in determining the outcomes of the case histories. Design guidelines, including suggestions for barrier pillars to isolate active panels from nearby gobs in bump prone ground, are also proposed.

By John Watson, Jay Rodgers

The world of blasting and explosive use continues to evolve into one which relies heavily on measurement, quantification, process control, and information feedback as a means of contributing to operational improvements. More than ever good blast performance, once thought to be a result of someone’s “artistic ability”, is giving way to “hard science” and measurement techniques. Variability in product performance and process control is becoming less tolerable with increasing environmental issues, regulatory pressure and public awareness.

Jan 1, 1998

In North-West Nelson the Riwaka Complex, a linear basic intrusive complex, is exposed for approximately 45 km. Some 500 km south, across the Alpine Fault, a linear zone of similar but less well known basic intrusives that may be correlatives of the Riwaka Complex is exposed discontinuously for about 80 km. The Complex was emplaced at several centres along a major tensional fracture zone that developed in upper Carboniferous to Lower Permian time. This fracture zone probably formed in response to the development of a west dipping subduction zone that gave rise to the Permian volcanic arcs in east Nelson and western Southland. The Riwaka Complex contains three rock suites. The Fractionation Suite, characterized by cyclic mineral layering and small scale cumulus banding is the largest and is divided into the Ultramafic, Hornblende and Plagioclase Series, each of which is subdivided into several units. The Cumulus Gabbros represent a restricted but important suite of unusual composition, while the third suite is the late phase Diorite Suite. Except in the lower units of the Ultramafic Series sulfide mineralisation is widespread. Pyrrhotite is the dominant sulfide with lesser chalcopyrite pentlandite and pyrite. Four significant zones of sulfide accumulation are recognised and discussed in some detail. Evidence suggests that the primary magma from which the Riwaka Complex was derived was sulfur deficient. It is concluded that the sulfur content of the Riwaka Complex was derived from assimilation of sulfur rich wall rocks during intrusive processes.

Jan 1, 1980

By Ivan Weber

Asking the question, “What do the world’s leading corporations and cutting-edge practitioners of sustainability put forth to guide a given mine site for planning and action toward ‘sustainability’?”, this paper explores the spectrum of methodologies and mindsets in available literature, then constructs an example for the large near-closure facility at Kennecott Utah Copper. Values, opportunities and constraints spring from physical, unutilized byproducts, from critical ecosystems and wildlife populations, from location relative to those ecosystems and proximate communities, and from the political will to perform adequate feasibility investigations. Patience, determination and thoroughness are imperative. Identifying most productive and, simultaneously, most protective and restorative, practical methods to approach ‘sustainability’ has become a central mission of industry and business, worldwide. A survey of recent international initiatives finds no single approach that establishes either a readily adaptable methodology or an appropriate set of ‘attention’ points, or agenda, to guide individual mining operations at specific locations toward the elusive but essential goal of ‘sustainable’ mining. Untying this convoluted knot of contending factors requires willingness to recognize and work within ecological constraints for community long-term needs. Occasionally, the task requires the sword of Alexander the Great. Through integration that is unflinchingly honest ethically, culturally, economically, ecologically and scientifically, fully cognizant of place and community at whatever scales are of greatest significance, and integrative of both problem-response and opportunity, we may envision a mineral extraction and beneficiation future that achieves the best, most nearly sustainable, results possible. Industrial ecology (IE), with its clear emphasis on community, ecosystems, and sustainable economic stimulation, presents a sufficiently broad and adaptable discipline to facilitate planning and management toward sustainable mining. The creation of sustainable jobs encapsulates IE’s analogy to the niche survival strategies of organisms in nature. Open to common-sense recognition of faults and opportunities at appropriate scales, IE is less a discipline or prescribed methodology than a mindset, willing to be rigorously scientific when science is imperative, but also willing to exercise “art” when creativity or community engagement are needed. IE is also capable of future-looking compassion for peoples and nature. Looking beyond what has occurred to date, the case of Kennecott Utah Copper provides ample illustration of possibilities for community economic development, environmental management, and significant initiatives beneficial at regional and planetary scales, to become recognizable as deserving of the label, ‘sustainable.’ Through what this researcher terms “whole mine, whole region, whole planet” thinking, strategies become visible and subject to serious consideration, presenting a path to best possible accomplishment in mining. Constituting a maximal broadening of mining’s “traditional” scope, the integrative approach proposed here is the ‘paradigm shift’ being made by many other industries around the world. In aggregate, these steps are the only hope for avoidance of environmental, social and economic risks that threaten to curtail resource development and impair mining companies’ ‘social license to operate.’

Jan 1, 2005

By B Nielsen, H Lehto, J Rohleder, C Robben

Sensor-based ore sorting is being increasingly used to reduce the amount of low-grade and waste material processed in mineral concentrators. This type of preconcentration provides bottom-line benefits to users by reducing the amount of energy, water and consumables, as well as reducing capital cost. Existing operations can increase metal production, while previously uneconomic deposits and low-grade stockpiles can also be exploited. The technology can also be used to separate ore types for selective processing. The path to implementing sensor-based sorting may include:• geometallurgical evaluation• first inspection testing to investigate sensor response• bench-scale testing where sensor selection is not obvious or for difficult applications• performance testing in full scale sensor-based sorting machines• larger scale site-based piloting with a temporary semi-mobile plant installation. Sorting requires material to be suitably prepared and presented to the machines and typically this consists of crushing and screening to limit top size and optimise liberation. However, where material streams are suitably sized and prepared, additional equipment may not be required (e.g. the sorting of semi-autogenous grinding (SAG) Mill pebble streams).This paper presents a case study of economic upgrading of gold ore, by preconcentrating with sensor-based ore sorting. The case study examines sorting amenability, test work, the feasibility study through to implementation, with associated flow sheet development. The development process is analysed and evaluated with a view to rationalising the process for development of future projects. In addition, limited financial modelling based on expected results is shown to illustrate the benefit to the operation.CITATION:Nielsen, B, Rohleder, J, Lehto, H and Robben, C, 2017. Sensor-based ore sorting to maximise profit in a gold operation, in Proceedings MetPlant 2017, pp 131–146 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By A Hoyle, P Walker, D Bennett

The Phu Kham copper-gold operation located in Laos People’s Democratic Republic (PDR) is owned and operated by Phu Bia Mining Limited. PanAust Limited, based in Brisbane Australia, holds a 90 per cent interest in Phu Bia Mining Limited, with the remaining 10 per cent held by the Government of Laos PDR.The 12Mt/y copper-gold concentrator at Phu Kham commenced production in April 2008. Flotation copper and gold recovery from commissioning was consistently poor, due to the high levels of pyrite and problematic secondary and oxide copper species and non-sulfide gangue.The low recoveries of copper and gold from Phu Kham were recognised during the feasibility study design phase. A bulk sulfide flotation regime in roughing produced high recoveries, however a large capacity cleaning circuit was required and there was risk of not meeting saleable concentrate grade specifications. The installed design offered a capital efficient compromise to ensure that a concentrate grade of 24% copper could be achieved at acceptable recoveries.Incremental improvements in copper recovery were achieved by 2011 through conversion of conditioning cells to flotation cells in both roughing and first cleaning and increased cleaner capacity through the installation of a Jameson cell. In 2012 the Phu Kham Upgrade Project was commissioned to increase mill throughput, along with additional rougher and cleaner capacity to increase residence times at the nominal 16 Mt/y throughput. The marginal reduction in primary grind size due to the additional ball milling power also provided a small recovery improvement.This paper presents the development, design, implementation, and performance of the Increased Recovery Project commissioned in April 2013 which targeted the major causes of copper loss from the circuit. Based on fundamental and detailed test work and mineralogical analysis of concentrator streams, an optimised design was developed which has increased copper and gold recoveries by over 5% and 10% respectively. The Increased Recovery Project has positioned the concentrator to process high pyrite ores that were previously considered untreatable, and opened further opportunities for maximising flotation recovery by de-bottlenecking plant regrind and cleaning capacity.CITATION:Hoyle, A, Bennett, D and Walker, P, 2015. The increased recovery project at the Phu Kham copper-gold operation, Laos PDR, in Proceedings MetPlant 2015, pp 246–265 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By N. W. Kirshenbaum

"The Marconaflo slurry system was originally developed to reduce costs and solve technical problems in the marine transport of mineral cargoes. In the short time since its inception, it has been found to offer economies and advantages for land-based and in-plant materials handling. This efficient method of reclaiming and slurrying particulate materials at very high pulp densities can be directly utilized in a wide variety of mineral process systems. These include: storage-reclaim applications, where even cohesive, compacted materials can be reclaimed from settled storage ""on demand""; the growing number of hydrometallurgical operations wherein slurried materials are processed to extract or yield metals; certain applications associated with pyrometallurgical treatment; and as a means of augmenting the performance of conventional mineral dressing equipment, such as thickeners.INTRODUCTIONIn the continuing effort to lower costs of producing minerals and extracting metals, the field of handling and transportation often receives too little attention from those engaged in the mining and winning of ores and metals. This comment, which pertains to ferrous and non-ferrous as well as to non-metallic producers, is especially pertinent to products having relatively low value, where transport costs can be a major portion of the delivered selling price to the minerals receiver.One method which was developed recently for the purpose of reducing costs and solving technical problems in marine transport and handling of mineral cargoes is the MARCONAFLO slurry system. A notable feature of this system is its versatility; in addition to its use in marine transport1*, some of its diverse applications have included the mining and reclaiming of tailings2 and in-plant materials handling3. As the concept and fundamentals of this system have been well explained previously4,5, the mechanics of the system will not be elaborated upon here. Rather some specific ways in which MARCONAFLO can be applied to processing and extraction will be explored."

Jan 1, 1973