Search Documents

By C. H. Kats, E. G. Meiter, J. J. Bloomfield

"INTRODUCTION.Street manholes for underground power and signal circuits, and for sewers vary in size from small openings that a workman can enter, to large central vaults. As the gas hazards in manholes are similar to those in mines, the mine safety committee of the Bureau of Mines was asked whether the miners' flame safety lamp is a practicable device for indicating inflammable gases in manholes.The coal miner detects firedamp (methane or CH4) with his flame safety lamp by observing the luminous can or the increased length of flame that appears when 1.5 per cent or more of the combustible gas is present. The lamp flame also warns him of lack of oxygen by going out when the oxygen becomes less than 16 to L7 per cent. A tentative rule regarding the proposed use of safety lamps at manholes has been suggested previously as follows: ""Testing for gas: Do not enter manholes until you have .assured yourself that the manholes are free from dangerous gases, by testing with an approved safety lamp, by ventilation, or by other adequate methods."" The Bureau's committee recommended that miners' flame safety lamps are not suitable,testing in manholes because hydrogen gas may be formed therein. The flame safety lamps approved by the Bureau of Mines for use in aseous mines are safe in presence of methane and while not tested against the members of the paraffin hydrocarbon series (CnH2n+2) higher than methane they been have been used therein; the lamps should not be used in hydrogen or acetylene they can initiate explosions in presence of these gases."

Oct 1, 1925

By Shangshu Li, Xin Li, Xionggang Lu, Xingli Zou, Kai Zheng, Yinshuai Wang

Ti5Si3/TiC composite has been successfully prepared from the titanium-rich slag/SiO2/C mixtures precursors by an electrochemical process. The electrochemical production process was carried out in molten CaCl2 salt at 1000 °C and 3.8 V. A pressed cylindrical pellet of titanium-rich slag/SiO2/C mixtures served as a cathode, and a solid oxide oxygen-ion-conducting membrane (SOM) tube filled with carbon-saturated liquid tin acted as an anode. The phase transformation of the cathode pellets during electrolysis process was investigated, the microstructure of the obtained products was characterized. It is found that the reaction pathways can be divided into three main stages during the electro-reduction process. The first stage is the generation of calcium compound, the second stage is the electrochemical reduction of the compound, and the third stage is the formation of Ti5Si3/TiC composite. The prepared Ti5Si3/TiC composite exhibits homogenous and nodular particle morphology.

Mar 1, 2018

Table A-1. Number of underground coal mines and samples collected for underground occupations, 1988-92 [ ]

Jan 1, 1997

By H. Sevim

In this paper, the research effort in simulating the operation of underground coarse-coal hydrotransport systems (UCCHS) is summarized. The equipment of the system to be simulated is already optimally selected by using an analytical optimization model. The purpose of the simulation model is to test the performance of the system and to obtain the distribution of the operating parameters such as water and power consumption, amount of slurry delivered to the preparation plant, etc. Knowledge of the distribution of these parameters is essential for the efficiency of the design and the operation of the system.

Jan 1, 1985

By W. R. Byrnes

This project was initiated on October 1, 1980 and will be completed on December 31, 1983. The project was Initially approved and funded by the Office of Surface Mining and subsequently was moved to the jurisdiction of the Bureau of Mines. It was administered through the Indiana Mining and Mineral Resources Research Institute. The research was done to assess reforestation success and ultimate productivity for areas reclaimed under the Surface Mining Control and Reclamation Act of 1977 (P.L. 95-87). The Permanent Regulatory Program for implementation of P.L. 95-87 Includes provisions for revegetation that require seeding of ground cover plants to control erosion until permanent vegetation such as tree species Is established, and restoration of mined land to its original or better productivity. Much of the land to be surface-mined presently supports forest cover and it is anticipated that reconstructed minesoils will exhibit high productive potential for hardwood tree species. Hence, information was needed on compatibility of ground cover and tree seedlings when established concurrently as well as on revegetation success under postmining versus premining conditions.

Jan 1, 1983

By R Van Laeren, G Langerak, S Fityus, K Koosmen

Co-disposal of partly-dewatered mixed-plant rejects (MPR) from coal processing into spoil dumps is gaining favour amongst Australian coalmine operators in preference to conventional tailings disposal methods which require a tailings dam. Owing to their often low permeabilities and high degrees of saturation, MPR materials may be prone to the development of excess pore pressures when covered by spoil during routine dump advancement. The likelihood of dump failure will increase if these pore pressure regimes and the associated delay of shear strength development are not accounted for during waste dump design. To date however, little is known about these pore pressure regimes due to the complexities associated with their in situ measurement.This paper describes the in situ measurement of pore pressures in a cell of MPR placed within a coalmine spoil dump. Four vibrating wire piezometers (VWPs) were placed within a cell that was then filled with MPR and allowed to consolidate under self-weight before advancing an adjacent tiphead across the cell. The VWPs recorded the transient pore pressures during MPR placement and dump construction, and their interpretations are described within the context of laboratory measured parameters. Following analysis of the measured pore pressures, their implications on shear strength and dump design are also discussed.CITATION:Koosmen, K, Langerak, G, Simmons, J, Fityus, S and Van Laeren, R, 2015. Field measurement of transient pore pressures within co-disposed processing rejects placed in a spoil dump, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 63–72 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By John S. Wakeman

The initial step in the pelletizing of iron ores is the production of green balls. The importance of this step cannot be overemphasized as the physical quality of the green balls has a very significant effect on the subsequent induration process, regardless of the type of the indurating equipment employed. The ability of the green balls to withstand the rigors of handling, distribution, compaction and drying will have an effect on the degree of success of any pelletizing operation. Many factors affect the physical quality of the green balls including the prior processing of the iron ore, the characteristics of the balling feed and the type and quality of the binder used (if any). When working on the development of a new project or studying an existing operation, it is often desirable to determine what effect variations in these factors will have on green ball quality. It is generally impractical to make these determinations on a commercial, or even pilot plant scale, especially when the number of variables to be studied is large. Because of this, many organizations have developed batch techniques for producing green balls to enable them to perform such investigations with a minimum of time and expense. The batch balling method is at best, only an approximation of commercial balling systems. Many practitioners employ the use of pre-formed seed pellets to initiate a batch run. Thus, the growth mechanism encountered in any experiment is essentially snowballing. Unless an instability is introduced into a balling test (such as an excessive initial feed rate or an unusual feed material characteristic) the growth mechanism of coalescence is not present to a significant extent nor is it desirable. In a continuous operation, both mechanisms are present and necessary to sustaining the system. The batch balling technique thus produces pellets in an idealized manner and cannot be used to directly predict commercial green ball qualities. A general relationship does exist however, and the procedure is fairly sensitive to variations in test parameters. Although many refinements to this technique have been introduced over the years, batch balling is still essentially an art and subject to "operator effect". Therefore, to assure consistant and reliable results, skilled technicians who carefully adhere to established practice must be utilized.

Jan 1, 1971

By J. A. Bakken

Thermal plasmas are interesting for a wide range of metallurgical and chemical processing applications. The 300 kW experimental reactor PRESS, which has been in use since 1987, is operated in the transferred arc mode with three or one plasma torches . Tests include remelting of silicon fines and production of ultrafine silica. Work on a novel three stage process for production of silicon metal is under way. A 1:1 model of the plasma reactor is used to measure the wall heat flux distribution calorimetrically. The cold walls of this model are divided into several water-cooled sections. The same plasma torches as in the real hot-wall reactor are used. In parallel to the experiments and calorimetric measurements theoretical work is done on numerical modelling of one and three transferred arcs. A modified version of the flow simulation program FLUENT from Creare Ltd. is used.

Jan 1, 1991

By R. S. Dean

"INTRODUCTION The metallurgical research program of the Bureau of Mines has been somewhat disorganized, but generally advanced by the increased activities of the war period. The present report is for the purpose of summarizing the work of the Bureau in this field for the past 15 years and indicating its future plan.Fifteen years ago the Bureau turned from its pioneer work on the physical chemistry of steelmaking to an emphasis on raking a pure steel synthetically, rather than by refining, that is, :producing each of the steel 'constituents in the pure state and combining them by simple melting. Such a procedure permits the use of less high-grade ores, not only of iron, but of the ferroalloy metals, such as manganese and chromium,This program has led to extensive work on iron-ore concentration, agglomeration, reducibility of ores and agglomerates, direct reduction of iron ores and concentrates by a wide variety of processes; special refining processes for iron, the production of pure mangenese, chromium, and cobalt from low-grade ores by electrolytic processes, the production of ferrochromium, ferronickel, and ferronickel-cobalt from low-grade domestic ores, and the development of many special alloys to effectively use the new products.The status of the work in each of these fields and the future program of work, together with a bibliography of papers and patents by the Bureau staff on each of these subjects, are given."

Jul 1, 1946

By M. Bueno, T. Chavez Matus, M. S. Powell, S. Michaux, S. Luukkanen

Comminution tests are an essential element in the design of ore beneficiation plants. Many methods have been developed to assess the breakage characteristics of rocks to generate parameters for modelling. However, most of the existing methods are laborious, expensive and require large samples. Consequently, test work has been traditionally conducted with a few representative reference samples. On the other hand, geometallurgical modelling programs require an extensive amount of test work to allow understanding the variability of ore properties within the deposit and establish spatial geometallurgical domains that show the differential responses to mineral processing. Therefore, comminution tests for geometallurgy need to be more efficient in terms of time, cost and sample size. This paper introduces a new testing device (Geopyörä) which is capable of measuring forces and energy applied to rock particles during the breakage process. The new testing method uses smaller samples and can be up to 50 times faster than other commonly used tests in the industry. This paper presents the concept prototype and the preliminary test work results, which have been benchmarked against some of the industry standard tests, such as the JK Drop Weight Test (JKDWT), the SMC Test® and the Bond ball mill test. Keywords: Geometallurgy, comminution, ore breakage characterization, variability.

Jan 1, 2020

By H. Bouzahzah

The field of quantitative mineralogy has evolved significantly through the development of image analysis techniques and information technology. Quantitative mineralogical characterization can now be routinely conducted for determining ore compositions and understanding the behaviour of minerals within mineral separation processes. The characterization of mine tailings is another important application of quantitative mineralogy. The estimation of acid and neutralization potential as well as the interpretation of kinetic leaching test results are often based on quantitative mineralogical knowledge (mineral abundance, texture, metal distribution amongst minerals, etc.). The objective of this paper is to determine and compare the accuracy of four mineralogical characterization techniques that are often used for environmental sample analysis: (1) X-ray diffraction, (2) normal analysis from chemistry analyses, (3) normal analysis from specific gravity measurements and (4) SEM-EDS image analysis. For this purpose, three artificial samples were assembled by mixing pure minerals in proportions often observed in mineral processing plant tailings. BILMAT, a statistical data reconciliation software, was applied to reconcile the chemical analyses with the results of other mineralogical analysis techniques and to estimate the acid and neutralization potential of actual mine tailings samples. The acid mine drainage was qualified from the acid potential and neutralization potential equilibrium as determined through quantitative mineralogical analysis. The statistically reconciled data made it possible to predict the metal deportment as a function of their bearing minerals and therefore, in the case of neutral contaminated drainage, to assess metal leaching potential.

Jan 1, 2016

By G. W. Birge

Twenty-eight samples, representing the Pittsburgh, Lower Kittanning, Stockton-Lewiston, Coalburg, Winifrede, Cedar Grove, Peerless, No. 2 Gas, Powellton, and Eagle beds, were carbonized by the Bureau of Mines--American Gas Association (BM-AGA) method, and yields of products and physical properties of cokes were determined. Expanding characteristics of 22 of the samples were determined in the Bureau of Mines sole-heated oven. The Kanawha County coals tested were high-volatile A bituminous in rank, with dry, mineral-matter- free fixed- carbon contents ranging from 53.9 to 66.3 percent. With few exceptions, they were chemically satisfactory for metallurgical use, and most of the coke-strength indexes were within the industrially accepted range for high-volatile blending coals.

Jan 1, 1963

By R. A. Hemstock

"Simple classification systems are now being used which will describe adequately the surface vegetation, the topography and the peat for any muskeg condition. Good progress is being made in determining some of the mechanical properties of muskeg and it is apparent that the science of soil mechanics will apply largely to these studies. Correlation is also indicated between shear strength as determined by the shear vane tester and vehicle performance. Several tracked vehicles are now available which perform well in muskeg and advances in this field have come rapidly in the past few years. Testing is under way on the largest of all muskeg vehicles -the thirty-five ton Musk Ox. This vehicle will fill the last gap for the oil industry and will make possible the movement of large drilling rigs at any season of the year."

Jan 1, 1960

By M. R. Robben

Carbonates have gained significant economic importance for the human kind. On one hand over a hundred uses are listed for carbonates. On the other hand, carbonates host base metal deposits. Although the carbonates play a significant part in the development of those deposits, in the mineral processing they consume acid and cause selectivity problems during flotation and leaching. Carbonates also accompany other industrial minerals as waste rock. For all those cases it necessary to find a technique to separate carbonate as early as possible in the processing chain. In this paper, the applicability of near-infrared spectroscopy (NIRS) sorting for the separation of carbonates is discussed. NIRS sorting is a sensor-based sorting technique, in which particles are singularly detected by a sensor and then rejected by an amplified mechanical, hydraulic or pneumatic process. This technique can for example be implemented in the process as a pre-concentration step for coarse particle sizes up to 300 mm. NIRS sorting discriminates among materials based on the difference that exist between their spectral properties in the near-infrared (NIR). Vibrations of molecular bonds in carbonates cause characteristic spectral properties in the NIR, which makes carbonates detectable, possible to identify, distinguish and separate from other rock materials. The spectral properties can also be used to distinguish between different carbonate minerals and mixtures. If the spectral variations are large enough for detection, sorting based on NIRS is possible. Feasibility studies on sensor-based separation of carbonates in the processing of talc, borate, fluorite, marble, zinc-oxides, copper sulphide and iron ore as well as the discrimination of calcite and dolomite mixtures are conducted and indicate the high potential of NIRS sorting in the minerals industry. Keywords: carbonate separation, sensor-based sorting, near infrared spectroscopy, NIRS sorting

Sep 1, 2012

By Philip D. Anderson, Ralph Hultgren

Heat contents of extremely pure iron were measured over the range 300"to 1433"K, using a diphenyl ether calorimeter. Results from three samples containing widely differing impurities agreed with one another and with Previously reported results at higher temperatures (1184 ° to 1809°K) by Olette and Ferrier. From these data a table of heat contents of iron has been Prepared which is believed to be more accurate than those previously available. CP values have been derived which are consistent with these heat contents, with the best experimental Cp data, and with the thermodynamic conditions of equilibrium between bcc and fcc iron. The opinion is expressed that low-temperature extrapolations of presently known Cp values for y-Fe are not reliable. It would seem that the thermodynamic properties of iron, which is by far our most important metal, should have been well established long ago. This is not the case, however. As discussed by Olette and Ferrier,' there is objection to every earlier heat content measurement. While the best true Cp determinations agree well at temperatures below the Curie point, there is wide divergence at higher temperatures. Several investigators have examined available data and attempted to calculate thermodynamic functions for iron that are consistent with the two equilibrium temperatures of bcc and fcc iron. The two primary efforts were those of Austin' in 1930 and Darken and smith3 in 1948. The recommended values differ considerably; integration of Austin's Cp values leads to a heat content at 1100°K which is 300 cal per g-atom higher than the value recommended by Darken and Smith. The compilation of Fisher4 in 1949 was based on the selection of Austin. In 1956, Weiss and Tauer obtained yet another set of values by resolving Cp values into components due to dilation, lattice vibration, electronic excitation, and magnetism. The magnitude of contribution by each component and its dependence on temperature was estimated by semiempirical means. Their values are not self-consistent in that they do not form smooth curves when plotted vs temperature; moreover, their calculations cannot easily be repeated since they do not give the values of some of the parameters used. Clearly, experimental values for iron were in a most unsatisfactory state. The presently described measurements of the heat content of iron were therefore undertaken, covering temperatures as high as 1433°K. While the work was in progress, the high-temperature (1193" to 1789"K) heat content measurements of Olette and Ferrier' were published; in the region of temperature overlap the present results agree with Olette and Ferrier well within experimental accuracy. It is believed that the present results, combined with those of Olette and Ferrier, provide for the first time a reliable set of heat contents of iron from room temperature to the melting point. From these data, guided by available Cp measurements, it proved possible to derive Cp, entropy, and free energy function values for @-iron from room temperature to the melting point, and for y- iron in the temperature region of its stability. Exhaustive study led to the conclusion that extrapolations of y-iron functions to room temperature were not reliable enough to be useful; hence these have been omitted from the tables. EXPERIMENTAL Materials. Three samples of extremely high purity iron from different sources, containing widely different impurities, were measured. The first of these, designated "Chipman", was kindly supplied by Dr. K. K. Kelley of the U. S. Bureau of Mines from a lot which was made many years ago by Dr. John Chipman of the Massachusetts Institute of Technology. The second, designated6'Teddington", was supplied by the National Physical Laboratory, Teddington, England, from a lot zone-refined by them. The third sample, designated "Irsid", was supplied by the Institute de Recherches de la

Jan 1, 1962

By Alfred H. Bell

Drilling activity increased in Illinois in 1935. There were 34 com-pletions as compared with 26 in 1934 and 18 wells were drilling at the end of 1935. Some large blocks of acreage were leased in Marion and Clay counties near the central part of the Illinois structural basin. Production of oil in the state totaled 4,305,000 bbl., a decrease of 4 per cent from that of 1934 There was some curtailment of production in the early part of 1935 but none after April 30 as shown in the following table. Percentage Pro-duced of Potential ProductioN (USING September 1934 Period as BaSis) Jan. .l-Feb. 20............................................ 79 Feb. 21-Feb. 25............................................ 85 Feb. 26-Feb. 38............................................ 79 Mar. 1-Mar. 11............................................ 85 Mar. 12-Mar. 31............................................ 100 Apr. 1-Apr. 9.......................................... 80 Apr. 10-Apr. 30............................................ 86 May 1-Dec. 31........................................... 100 This is equivalent to an average curtailment throughout the year of 5 per cent. The price of Illinois crude oil at the wells remained constant during 1935 at $1.13 per barrel. A small amount of oil was sold at a 1ower price, notably from the Dupo field, but to arrive at a value for the state's production there would be little error in assuming an average price of 81.13, giving a total value of $4,864,465. The following table shows production in Illinois by moths in 1935, according to the U.S. Bureau of Mines. Jan............. 332,000 May.......... 382,000 Sept ,............. 370,000 Feb............. 295,000 June. ........... 858,000 Oct.............. 391,000 Mar............ 370,000 July............ 377,000 Nov............. 369,000 April............ 338,000 Aug............. 379,000 Dec............ 344,000

Jan 1, 1936

By Alfred H. Bell

Drilling activity increased in Illinois in 1935. There were 34 com-pletions as compared with 26 in 1934 and 18 wells were drilling at the end of 1935. Some large blocks of acreage were leased in Marion and Clay counties near the central part of the Illinois structural basin. Production of oil in the state totaled 4,305,000 bbl., a decrease of 4 per cent from that of 1934 There was some curtailment of production in the early part of 1935 but none after April 30 as shown in the following table. Percentage Pro-duced of Potential ProductioN (USING September 1934 Period as BaSis) Jan. .l-Feb. 20............................................ 79 Feb. 21-Feb. 25............................................ 85 Feb. 26-Feb. 38............................................ 79 Mar. 1-Mar. 11............................................ 85 Mar. 12-Mar. 31............................................ 100 Apr. 1-Apr. 9.......................................... 80 Apr. 10-Apr. 30............................................ 86 May 1-Dec. 31........................................... 100 This is equivalent to an average curtailment throughout the year of 5 per cent. The price of Illinois crude oil at the wells remained constant during 1935 at $1.13 per barrel. A small amount of oil was sold at a 1ower price, notably from the Dupo field, but to arrive at a value for the state's production there would be little error in assuming an average price of 81.13, giving a total value of $4,864,465. The following table shows production in Illinois by moths in 1935, according to the U.S. Bureau of Mines. Jan............. 332,000 May.......... 382,000 Sept ,............. 370,000 Feb............. 295,000 June. ........... 858,000 Oct.............. 391,000 Mar............ 370,000 July............ 377,000 Nov............. 369,000 April............ 338,000 Aug............. 379,000 Dec............ 344,000

Jan 1, 1936

The Determination of Sound Exposures (DOSES) software was developed by the National Institute for Occupational Safety and Health (NIOSH) specifically for use by mine management and safety personnel. DOSES simplifies the record-keeping and analysis associated with time-motion studies and worker noise exposures, making it easier to identify and solve noise problems. The software relies on a time-motion study that profiles the worker?s daily activities. At the same time, noise measurements are collected with a dosimeter or sound level meter (SLM). Observations about the worker?s location and tasks or other activities are recorded along with times and durations so they can later be matched up with the noise data. After the completion of a time-motion study of the worker?s daily tasks and locations (possible noise sources), which measures the worker?s noise exposures during the recorded events, the information is entered into DOSES. The program then displays information about the worker?s accumulated noise dose over time.

Jan 1, 2009

By Frederico Mayerhofer

A produção brasileira de minério e pelotas abastece siderúrgicas de diversos países e contribui significativamente para o desenvolvimento global. Com a redução acentuada do preço do minério de ferro a redução de custos de produção de pelotas se torna ainda mais necessária. Nos fornos das usinas de pelotização é consumido o combustível responsável pelo maior custo de produção das pelotas, que é o gás natural. O presente trabalho tem como objetivo reduzir o consumo de gás natural utilizados nos fornos do tipo grelha móvel das usinas de pelotização, através da otimização dos fluxos de gases e temperaturas necessárias ao processamento térmico das pelotas.

Aug 17, 2017

By George Quackenbos

The principal objective of this Program is the design, fabrication and testing of an Environmental System for operation in underground mines, to assess the effect of various mining systems on the contaminant levels near the mine face and within return airways. In order to determine the effect on airborne contamination in mines resulting from the development of new mining techniques, equipment and control systems, a Comprehensive Monitoring System is required to assess such contamination levels at critical and strategic locations and relate this information with ventilation parameters. The three variables to be sensed on a continuous basis are airborne dust concentration, methane concentration and ventilation air velocity. Each Monitoring Station will consist of a self-contained unit containing a power source and sensors to monitor the three above mentioned parameters. Ruggedness, reliability, ease 'of operation and intrinsic safety are important design objectives. Data gathered by each Monitoring Station will be fed to a Central Data Acquisition System by means of a portable transfer unit.

Jan 1, 1982