Search Documents

By Richard F. Flanagan, Robert H. Marshall

The Republic of Singapore’s Public Utilities Board is implementing the Deep Tunnel Sewerage System Project. The project’s deep tunnel component, 48 km of deep, large diameter sewer tunnels has been successfully completed (the works are in the defects liability period). Six International Design/Build tunnel contracts utilized eight Earth Pressure Balance TBMs ranging up to 7.23 m in diameter to deal with varied ground types ranging from deep soft clays to fresh granite. Numerous access/workshafts were constructed and using various support systems. This paper provides an assessment/overview of the tunnel contracts, tunnel excavation methods and equipment, and the shaft systems. Suggested enhancements to similar future projects are provided.

Jan 1, 2007

By V. M. Troughton

Further pile load testing has been carried out at Canary Wharf to compare the performance of base grouted and ungrouted bored piles founded in the Thanet Sand. The testing regime included three preliminary test piles and two working test piles. The results of these tests are summarised in Table 1 below. Two of the preliminary test piles were located only 14m apart to compare the performance of a base grouted and ungrouted pile in similar ground conditions. The load/settlement behaviour of these two preliminary test piles are compared on Figure 1. All the piles were drilled under bentonite with a drilling bucket. In the base grouted piles four grouting tubes were placed with the reinforcement cage to within 500mm of the pile toe. After the pile had been concreted these grouting tubes were then extended to the pile base by drilling and packers were installed. Grout was then injected into the four tubes simultaneously.

Jan 1, 1991

By C. J. Walker

The ever-increasing use off natural underground formations for storing natural gas has focused attention on the behavior of such storage formations under varying operating conditions. The need for a means of evaluating in¬dividual wells and groups of wells has become manifest. It is essential that industry and others be able to determine the rates of flow that can be ex¬pected from a given well or group of wells under different conditions and to ascertain whether certain wells are deteriorating. Such questions need more exact answers now than ever before because of the vital role underground gas storage plays in the industrial and domestic consumption of natural gas. The Bureau of Mines--in cooperation with the American Gas Association--has main¬tained an active interest in gas-well testing because of the implications of such test procedures on the consumption and efficient production of natural gas. A basis for testing gas wells was provided by the back-pressure method of Rawlins and Schellhardt (12).4/ They showed that for normal gas wells there is a consistent relationship between rates of delivery of gas and corresponding pressures when the formation pressures are used as the basis of interpretation, The equation for this relationship is as follows: Q = C (Pf2 - Ps2)n where; Q = rate of flow, generally expressed in cubic feet per 24 hours. C = a coefficient.

Jan 1, 1960

By A. J. Paul Laprairie

The process for which it is to be used is too often the only consideration in the design of a vessel. A de-sign allowing for practical manufacture and erection, as well as for proper maintenance, can often give over-all economies. Most platework in-stalled today is of welded construction. Therefore, metallurgical control is important in its manufacture. Also, because many concentrating and re-fining processes tend to be corrosive, the subject of protective coatings as a part of the manufacturing process is extremely important. The plant de-signer should know how to evaluate and specify controls for the metallurgy and for the coatings. Mining operations are becoming more sophisticated in the field of mechanical engineering. More and more emphasis is being given to preventive maintenance. The first step in any maintenance program, however, is good inspection service. This paper will suggest methods for the inspection of platework, and outline methods for repair and replacement.

Jan 1, 1963

By P. Gaskell

The paper examines the development of rock movement between a longwall extraction horizon and the surface for a fully caved mining situation. Physical modelling has been used to examine the mechanics of ground movement and the propagation of fractures around the longwall working. The paper discusses dimensional analysis, model construction and measurement technique and data processing of the results into effective graphical forms for further study.

Jan 1, 1988

By Mary Ellen Bruce Large

"In partnership with California Department of Transportation (Caltrans), Federal Highway Administration (FHWA), and with support from International Association of Foundation Drilling (ADSC), Deep Foundations Institute (DFI) organized a workshop on quality assurance (QA) practices for acceptance of post-grouted drilled shafts in conjunction with DFI’s 40th Annual Conference on Deep Foundations. The 1½-day workshop was held on October 15-16, 2015 at the Oakland Marriott City Center in Oakland, CA.Post-grouting, in the context of this workshop and report, refers to the alternative design and construction of base-grouted drilled shafts wherein a grout distribution system is installed during construction and used to grout the base under pressure after the drilled shaft concrete has gained adequate strength, resulting in a stiffer axial-compression load-displacement relationship and additional possible ground improvement effects.The primary goals of the workshop were to•?Identify and summarize the state of the practice for design, construction, inspection, verification, acceptance criteria, reliability and performance of post-grouting.•?Identify gaps and needs in quality assurance that should be addressed for successful use of post-grouting.This report is structured to follow the workshop program: workshop presentations outlined the state of practice and views from owners, engineers and contractors on acceptance of post grouting methods for drilled shafts; and subsequent workshop discussions attended by a small invited group of participants focused on identifying areas of agreement and disagreement on post-grouting best practices, acceptance criteria, design and verification procedures, and inspection requirements. A partial list of attendees of the open and closed sessions is provided as Appendix A, and copies of presentations are included as Appendix B.FHWA and Caltrans are the primary audiences for this report, and its content will be used to develop a roadmap for deploying the findings into policy and practice. The secondary audience is the broader industry group, and the report content will be disseminated in a variety of formats."

Jan 1, 2016

By Mary Ellen Bruce Large

"INTRODUCTIONIn partnership with California Department of Transportation (Caltrans), Federal Highway Administration (FHWA), and with support from International Association of Foundation Drilling (ADSC), Deep Foundations Institute (DFI) organized a workshop on quality assurance (QA) practices for acceptance of post-grouted drilled shafts in conjunction with DFI’s 40th Annual Conference on Deep Foundations. The 1½-day workshop was held on October 15-16, 2015 at the Oakland Marriott City Center in Oakland, CA.Post-grouting, in the context of this workshop and report, refers to the alternative design and construction of base-grouted drilled shafts wherein a grout distribution system is installed during construction and used to grout the base under pressure after the drilled shaft concrete has gained adequate strength, resulting in a stiffer axial-compression load-displacement relationship and additional possible ground improvement effects. The primary goals of the workshop were to•?Identify and summarize the state of the practice for design, construction, inspection, verification, acceptance criteria, reliability and performance of post-grouting.•?Identify gaps and needs in quality assurance that should be addressed for successful use of post-grouting.This report is structured to follow the workshop program: workshop presentations outlined the state of practice and views from owners, engineers and contractors on acceptance of post grouting methods for drilled shafts; and subsequent workshop discussions attended by a small invited group of participants focused on identifying areas of agreement and disagreement on post-grouting best practices, acceptance criteria, design and verification procedures, and inspection requirements. A partial list of attendees of the open and closed sessions is provided as Appendix A, and copies of presentations are included as Appendix B.FHWA and Caltrans are the primary audiences for this report, and its content will be used to develop a roadmap for deploying the findings into policy and practice. The secondary audience is the broader industry group, and the report content will be disseminated in a variety of formats."

Jan 1, 2016

By Barun Gorain, Andy Stradling

"The traditional metallurgical scale-up techniques for flotation plants are based on lumped flotation rate constants, dimensionless hydrodynamic numbers and the use of safety factors. Once the plant has been designed, the flotation principles that govern scale-up play almost no role in the optimisation of the circuit to meet its metallurgical targets. This deficiency can potentially lead to a plant design incapable of meeting its targets, especially when circuits incorporate large flotation cells. This paper demonstrates the application of the k = PSbRf model in providing a suitable framework for flotation modelling, scale-up and circuit optimisation, thus presenting an integrated approach to the problem. Studies were conducted at Teck Cominco’s Red Dog concentrator to characterise cell hydrodynamics, gas dispersion properties, fioth flow behaviour, entrainment and ore floatability to obtain the key data necessary to develop a model for the flotation circuit. The findings of these studies are presented in this paper, which provide valuable insights into the modelling and optimisation of the Red Dog flotation circuit.INTRODUCTIONThe traditional methodology for flotation scale-up and plant design is based on the rule-of-thumb with safety factors, dimensionless hydrodynamic group similitude considerations, etc. With the recent trend towards larger flotation cells with volumes of 150 m3 and greater in concentrators, the problem of scale-up has become even more acute. The scale-up factors that may have been tolerated on smaller cells are not applicable to larger cells. The transportation of froth in these large cells adds further complexity to the problem. Arbiter et al. (1980) foresaw this problem and pointed out that if scale-up were attempted by rule-of-thumb and trial-and-error, then the probability of failure would increase with scale. This problem is confounded by the fact that the design and scale-up considerations used for a new flotation circuit play almost no role in optimisation of the circuit to meet its metallurgical target. This results in a plant design incapable of meeting its metallurgical targets. There have been several instances where new concentrators have required significant circuit modifications and additional capacity to achieve design targets."

Jan 1, 2002

By Dennis E. Jensen

Field studies were performed during blasting operations for strip coal mining above the room and pillar workings at Jenny mine in eastern Kentucky. The study is part of the Bureau of Mines program to develop criteria for the proximity of surface blasting to underground mines. Measurements and observations were made to identify physical changes in the mine. No change in the frequency of roof falls or any other indication of apparent damage was noted. Recordings of blast induced vibrations were made using sensors on the roof and floor of the underground mine and at the ground surface. A maximum particle velocity of 17.5 in/sec was recorded on the mine roof. The vibration data were analyzed and comparisons were made between roof vibration levels and those recorded on the mine floor and at the ground surface. Results are compared with previous blast vibration studies. Recommendations are made for further study toward developing criteria.

Jan 1, 1979

By George S. Dulikravich

An advanced semi-stochastic algorithm for constrained multi-objective optimization has been adapted and combined with experimental testing and verification to determine optimum concentrations of aJ10ying elements in heat-resistant and corrosion-resistant H-Series austenitic stainless steel alloys. The objective was to simultaneously maximize a number of alloy's mechanical properties. This research will result in a rigorous tool for the design of high-strength H-Series steels and other types of alloys unattainable by any means existing at the present time. Such a material-by-design tool will also be able to reduce or minimize the need for the addition of expensive elements such as Cr, Ni, Co, Nb, Ti, V, etc. and still obtain the optimum properties of an aJ1oy.

Jan 1, 2003

By Steven R. McCutcheon

ABSTRACT - The Bathurst-Newcastle district, a subcircular area approximately 50 km in diameter, contains 37 massive-sulfide Zn-Pb-Cu deposits that have defined tonnages, and has 58 additional significant occurrences. The largest deposit is Brunswick No . 12, with total reserves (including past production) of 148 million tonnes grading about 12.50% combined Pb-Zn. The deposits/ occurrences are spatially associated with a felsic volcanic pile that contains a significant sedimentary component. In the vicinity of the Brunswick deposits the pile is divisible into lower and upper sequences. The lower is characterized by megacrystic rhyolite (QFAS) and coarse- to fine-grained quartz ( ± feldspar) wackes and/or tuffites (QAS); the upper sequence is characterized by aphyric to sparsely porphyritic rhyolites (HWR), micro-breccias, and acid hyaloclastites with interbedded dark gray sedimentary rocks. A greenish gray to dark gray siltstone (GGS) separates the two sequences and hosts the sulfide deposits. Lithogeochemistry of !east altered samples shows that the QFAS and HWR have an igneous character, whereas the QAS and GGS have a sedimentary sig­ nature. The two types can be distinguished on the basis of total alkalies (Na2O + K2O) versus SiO2/Al2O3, and Ti02 versus Fe/(Fe+ Mg). Some trace elements, such as Sr and Y, also help differentiate the two types. The QFAS differs from HWR by having higher La/Yb ratios but lower Zr and Th. The Bathurst deposits do not show a close spatial association with rhyolites but rather are stratiform bodies (lacking clastic textures) within fine-grained sedimentary rocks. The scarcity of barite and other sulfates indicates that there was little mixing between the metal­ bearing fluids and cold seawater. High Fe/(Fe+ Mg) ratios in chlorites also indicate the fluids did not contain a significant seawater component. These features and the large size of many deposits suggest that the deposits formed from metal-rich pore waters that were released catastrophically from an acquifer in the footwall stratigraphy.

Jan 1, 1992

THOSE NOT MARKED ARE MEMBERS; MARKED THUS t ARE ASSOCIATES. HEAVY-FACED TYPE SIGNIFIES HONORARY MEMBERSHIP. JUNIOR MEMBERS ARE MARKED II. THE FIGURES AT THE END OF THE ADDRESS INDICATE THE YEAR OF ELECTION. AARONS, J. BOYD, Genl. Mgr., Chaffers G. M. Co., Boulder City, West. Australia. '05 ABADIE, EMILE R., Min. Engr Box 291, Porterville, Tulare Co., Cal. '76 ABBOTT, CLARENCE E., Genl. Supt., Iron Mines Div., 1405 Minnesota Ave., Bessemer, Ala. '04 ABBOTT, J. W., Min. Engr., "St. Omer," 123 N. Grand Ave., Los Angeles, Cal. '94 ABBOTT, Louis BENJAMIN, Chief Engr., Consolidation Coal Co., Elkhorn Div., Jenkins, Ky. '15 ABBOTT, ROBERT R., Met. Engr., Peerless Motor Car Co., Cleveland, Ohio. '12 ABE, ASAKA Yamagano G. M., Satsuma-Gori, Satsuma, Japan. '14 || ABRAHAMS, A. I., Student 1391 Madison Ave., New York, N. Y. '14 tACKER, E. O'C., Met Bethlehem Steel Co., Bethlehem, Pa. '86 ACKER, Louis K., JR., Min. Engr 565 Highland Place, Bellevue, Pa. '08

Jan 1, 1917

By J. R. Ross

Recovery of uranium from slightly alkaline mine water, available in the Ambrosia Lake district of New Mexico, was studied using countercurrent ion exchange columns developed by the Bureau of Mines. Approximately 5 million gallons of mine water containing 9 to 12 ppm U308 was treated by ion exchange using a 14-inch-diameter absorption column composed of five or six compartments each 4 feet deep. Uranium recoveries averaged in excess of 98 percent at solution flows ranging from 15 to 25 gallons per square foot per minute and resin loadings up to 3.6 pounds of U.08 per cubic foot. In subsequent tests, loaded resin was continuously eluted in a countercurrent elution column with a diameter of 4 inches and containing a bed of resin 9 feet deep. The resin was eluted to a residual loading of less than 0.06 pound of U305 per cubic foot, at a resin-retention time of 224 minutes, using only 1.9 volumes of 1.1 M NaCl-0.05 M NaHCO3 solution per volume of resin. Compared with existing ion exchange practices for recovering uranium from mine waters in the Ambrosia Lake district of New Mexico, use of these improved ion exchange contactors would reduce ion exchange resin requirements at least 70 percent and allow further substantial reductions in capital and operating costs.

Jan 1, 1971

By D. Bienstock

As part of the development of the hot-carbonate scrubbing process by the Bureau of Mines, the corrosion rates of steel in boiling solutions of potassium carbonate saturated with carbon dioxide and hydrogen sulfide were determined, and the effectiveness of various inhibitors was evaluated by Bureau researchers. The highly corrosive solution of carbonate saturated with carbon dioxide can be inhibited with a 0.2-percent concentration of either potassium chromate or sodium metavanadate. Solutions of carbonate saturated with carbon dioxide and hydrogen sulfide are mildly corrosive, 0.01 inch per year. Complete absence of corrosion is obtained with 0.2 percent sodium metavanadate or 0.15 percent vanadium pentoxide. Oxidizing inhibitors such as potassium chromate are destroyed in the alkaline sulfide mixture, N-alkyl trimethylene diamines, at a concentration of 0.1 percent, lower the corrosion rate to about 0.005. Sodium metasilicate, at a concentration of 0.6 percent, completely inhibits the corrosion but may deposit free silica in the system. Commercial cladding materials such as the epoxy coatings also prevent corrosion.

Jan 1, 1962

By Earle Faig

Earle Faig Along with other transportation modes, the barge industry will be greatly affected by trends in domestic coal production. Traditionally, coal has been one of the major commodities moved by barge. Now, because of events in the international energy market, coal is finally getting the recognition it deserves as a major component of the country's energy program. Perhaps even more significantly, a series of events has caused other countries to turn to the United States as a source of coal. Although the outlook for coal demand is optimistic, it will be greatly influenced by the ability of the transportation sector to handle the additional traffic. Because of its long experience in moving large quantities of coal, the barging industry is in an excellent position to capitalize on coal's increased popularity. A brief description of the barging industry should facilitate the discussion of coal as it relates to that industry. Barge companies operate on a river system that is over 40 Mm (25,000 miles) long. It includes the East and West Coasts and the Mississippi River System comprised by the Allegheny, Monongahela, Kanawha, Ohio, Illinois, Missouri, Tennessee, Cumberland, Arkansas, Warrior-Tombigbee, and Mobile Rivers, and some smaller tributaries. The Gulf Intracoastal Waterway stretching along the Gulf Coast from Brownsville, TX, to Apalachicola, FL, also is considered part of the inland waterway system. Approximately 1,800 companies operate on the inland river system and have a combined fleet of about 4,400 towboats and 28,000 barges. The fleet of towboats represents 4.8 GW (6.4 million hp) of power. The towboats comprising this fleet vary in size from a small harbor boat to a large line haul boat with 7.5 MW (10,000 hp) of power. The choice of size and power of the boat depends on a number of factors, including the size of the river and operational constraints, such as lock size, river-current rate, and water level. The choice also depends on the tow size. A single tow on a river capable of locking through 15 barges at a time handles up to almost 20 kt (22,000 st), whereas a tow on the lower Mississippi, which has no locks, can accommodate up to 41 kt (45,000 st) of cargo. Because the quality of coal is not typically damaged by exposure to the elements, it is usually moved in open hopper barges, although covered barges are used occasionally. The most frequently used size is the jumbo barge that measures 59 m (195 ft) long by 11 m (35 ft) wide by 4 m (12 ft) deep and can handle up to 1.4 kt (1,500 st) of coal. Advantages of Barge Transportation Barging offers several inherent advantages in transportation of bulk commodities like coal. First, barges can carry large quantities of product. A single jumbo hopper barge can handle 1.4 kt (1,500 st) of cargo while it takes 15 91-t (100-st) capacity rail cars or 57 trucks hauling 24 t (26 st) each to move an equivalent amount of cargo. Thus, barges can move more tonnage with less equipment than competing forms of transportation. Second, barging offers the most fuel efficient means of transportation. Less energy is required to push a load over water than to pull a similar load over land. The amount of pollution attributable to barge traffic is minimal because barges consume less fuel. Third, barging is an inexpensive form of transportation. The inland waterway industry transports about 12% of the nation's freight for about 2% of the total freight bill. This can be attributed to competition between the large number of companies on the river system and competition with other transportation modes. Fourth, barging is an environmentally safe method of transportation. Inland river routes expose fewer urban areas to hazardous substances than rail or truck. And barge spills occur less frequently than rail or truck spills. The industry does pose some disadvantages. The waterway system is constrained by the natural river network, so barges cannot travel on the most direct straight-line route. This means that barging is usually an incomplete form of transportation requiring interface with truck or rail. The industry's market is limited to those geographical areas that are located on or near the rivers. In addition, it is a time-consuming transportation mode, making it impractical for many types of commodities.

Jan 10, 1982

By Georgene Renner

With more than 800 booth spaces sold and 540 exhibiting companies displaying their wares, there was something for everyone on the exhibit floor of the 2014 SME Annual Meeting in Salt Lake City, UT Feb. 23-26. The following is a sample of what was offered at the 2014 meeting.

By Robert J. Rothwell

Underground mining of coal by longwall mining methods has not been a predominant technique in Ohio. To date, only five mines in the state utilize this method, however, the technique has sparked a certain amount of controversy. As a mining technique, longwalling was introduced into southeastern Ohio in the early 1970's but it did not attract public attention until the mines began moving into privately held surface lands. This occurred coincidentally at about the same time that the state of Ohio began to regulate the environmental impacts of underground mining. Prior to the passage of the Surface Mining Control and Reclamation Act in 1977, (SMCRA), Ohio's reclamation law, Chapter 1513 Ohio Revised Code (O.R.C. 1513) did not regulate underground coal mines. As a result of SMCRA, the Ohio Statute was amended in 1978, to include regulation of the surface effects of subsidence. The inevitable result was that existing mines were immediately subject to regulations that were not considered during the initial mine planning process. (For an excellent survey of Ohio Laws that deal with coal mine subsidence, see Zima, 1985. ) The problem faced at that time by both the coal industry and the Ohio Division of Reclamation (the agency within ODNR charged with implementing O.R.C. Ch. 1513.1, was that of attempting to superimpose permitting requirements, and design performance standards onto mines that' had been operational for a number of years.

Jan 1, 1986

By Ewan Selers, Gary Cavanough

Drilling automation technology is well advanced and automated drill rigs are in use at a number of operating mines. This is not the case for the other drill and blast processes due to significant technical challenges to overcome. These challenges, with regard to the current “on bench” practices, include placing the initiators, loading the explosive and connecting up the initiation system. Although difficult, these challenges will be solved with engineering advances.

Jan 1, 2016

By K Smith

This paper presents an assessment of the Robertson (2010a) method within the CPTu inversion parameter framework of Been et al. (1987), using CPTu calibration chamber data presented by Jefferies and Been (2015) and in other literature to assess the validity of the method, with particular focus on applicability of the method to TSFs (i.e. its applicability to loose silts and silty sands). The assessment demonstrates that although the method estimates values of k consistent with calibration chamber data, the method estimates values of m that are generally 1.5 to 2 times greater than calibration chamber data. As a result of this, the method generally overestimates Ψ for values of Ψ less than 0, and underestimates Ψ for values of Ψ greater than 0. This may result in both overly conservative assessment of materials as potentially liquefiable and unconservative predictions of material behaviour for loose materials.

Jul 1, 2021

Upon cessation of mining activity open-cast mine pits typically fill with water, forming a æpit-lakeÆ. The water in these lakes, in some instances, contains high concentrations of ædeleteriousÆ material. Containment and/or dilution typically requires an understanding of how stratification in the pit-lake will develop over a long timescale (say 100 years). Vastly different transport rates can develop due to differing hydrogeochemistry, basin morphology and climate. Numerical (computer) modelling is the most likely approach for successful prediction over long times. While lake modelling tools are available, useful numerical modelling requires improved understanding of transport in such systems because they are different to natural lakes in a number of ways. Notwithstanding the effort required to improve our understanding, the modelling provide a means of testing approaches to active management of pit-lakes.

Jan 1, 2002