Search Documents

By Edwin W. Meyer

The augered cast-in-place piling technique was used to install deep foundations 20 feet into weathered sandstone. The project involved the upgrading of the Air Quality Control System (AQCS) for a 560 megawatt coal fired power plant located in Stillwater, Minnesota. The site subsurface consisted of 20 feet of overburden overlying weak sandstone. The overburden consisted of sands and gravels with cobbles and boulders, and variable thicknesses of peat. Ground-water at the site was approximately 8 feet deep. Two foot diameter piers were selected to facilitate installation through the cobbles and boulders in the over-burden and to penetrate the sandstone 22 feet. During installation of the first pier, the weak sandstone broke down to sand-sized material that could not be cleaned from the pier hole without the use of slurry to hold the material in suspension. However, the use of slurry would significantly impact both schedule and cost. Since the sandstone could be easily drilled with the pier equipment, it was believed that 2 foot diameter deep foundations could be installed as designed using augered cast-in-place piling techniques. A brief test drilling pro-gram was conducted to evaluate the viability of 2 foot diameter continuous flight augers penetrating 22 feet into the weak sandstone. The test drilling indicated that augered cast-in-place installation techniques should be successful. Following a short delay to mobilize the additional required equipment, construction commenced. Installation of the 2 foot diameter augered cast-in-place piling to a depth of 22 feet into the weak sandstone was successfully performed.

Jan 1, 2006

By D. F. Malott

The Michigan Dept. of State Highways makes extensive use of geophysics for subsurface surveying which would be applicable for uses in other fields. Examples of resistivity surveys are given which include a proposed large-volume excavation with suggestions for land use after excavation, subsurface evaluation for engineering design, and a subsurface survey for land appraisal. An example of a combined refraction seismic and resistivity survey is shown where the resistivity is used for outlining the unconsolidated soils, while the seismic method is used to outline bedrock and to evaluate it for rippability. A refraction seismic survey at the bottom of bridge caissons for evaluation of bedrock uniformity and a rehtive aid in assessing rock strength is reported. These past several years have been a period of unprecendented construction and commercial expansion. Vast private manufacturing complexes and government road, power, and office projects are being built or are in planning stages. Nearly everywhere, municipalities are expanding outward and upward. Many towns are developing into cities and many cities are displaying new skylines, and the building boom shows little sign of slowing down.

Jan 1, 1970

By E. Siami-Irdemoosa, S. R. Dindarloo

Ease of excavation or rippability, also called diggability or excavatibility, is a critical decision-making parameter in the selection of both the overburden removal method and the required equipment in surface mining and geotechnical engineering projects. The most widely used method of estimating rippability is rock mass classification. Although there are different classification schemes in the literature, all of them have the two major limitations of sharp transitions at class boundaries and subjective uncertainties in decision making. In this study, the decision trees method was employed as a classification tool for estimating ground rippability, using the four rock mass parameters of weathering degree, uniaxial compressive strength, joint spacing and bedding spacing. The results were compared with those of the widely used method of diggability index rating (DIR) and a fuzzy-based DIR. The problem of subjective uncertainty was resolved in the proposed decision trees method, as the tree rules were derived automatically from the training data sets. Compared with fuzzy-DIR, a decision tree classifier is simpler, needs less computational time and is more appreciable by industry practitioners. Nevertheless, the proposed method is not flawless and, similar to both the conventional and fuzzy DIR methods, yielded poor estimations in particular instances. The limitations of the three methods are discussed.

Jan 1, 2015

By Paul Hewitt, Tim Smirnoff

Design and construction of the Epping to Chatswood Rail Line tunnels in Sydney, Australia required an innovative approach to define hydrogeological properties of the Sydney Hawkesbury Sandstone and provided an insight into the hydraulic behaviour of fractured sedimentary rocks. To meet restrictive water inflow and infiltration criteria both the pre-treatment of zones of fractured or highly jointed rock, and waterproofing using an interior spray on membrane for the finished drained tunnels and stations was required. Methods typically used to address the interaction of groundwater and tunnels in the Sydney Basin are demonstrated by case histories from major design-build tunnel projects.

Jan 1, 2005

By Tom Palangio, Ralph M. Olmstead

Video inspection of boreholes with cameras developed specifically for the mining industry is now possible. These designs are reliable, cost effective, and have the flexibility to be used in other applications.

Jan 1, 1998

Jan 1, 1993

By P Knight, P A. Walker, H E. Speight

Pushback 8 South is the final cut back on the south wall of the East Pit at BHPBilliton?s Mt Whaleback iron ore mine in the Pilbara region of Western Australia. Development of the cutback commenced in 1999 and is now nearing completion with ultimate pit walls up to 300m high. This paper describes the geotechnical, structural and hydrogeological setting of PB8S, reconciliation between design and slope performance and the slope engineering techniques used to effectively manage the risks associated with the slope. These techniques include slope buttressing and sequential mining with waste backfilling, as well as a detailed program of displacement and hydrogeological monitoring, structural mapping and slope stability assessment. During the course of slope formation recent developments in remote slope displacement monitoring using radar and remote structural mapping using terrestrial photogrammetry have also been applied. Aspects of the PB8S slope management plan are relevant to many large scale open pit slopes. This paper provides geotechnical practitioners with information which may be helpful in managing geotechnical risk in similar environments.

Jan 1, 2006

By O. T. Berge

Development and production from open cut mines continued its vigorous growth trend during the year 1968. Material handling and transportation were again exposed to the use of larger equipment with shovels, trucks and front end loaders leading the way. Highlights of World Mining Activities Africa: The Anglo American Corp. opened a new high-grade copper mine in Zambia during the year. In Angola, the Companhia Minera do Lobita planned a 3 million ton iron ore production for 1968 from new mines which will ultimately produce 5 million tons per year. A feasibility study of Bethlehem Steel Co., for the development of large high- grade iron ore reserves in Gabon, was in final stages of completion this year and Pickands Mather and Co. continued its investigation of iron ore deposits along the Ivory Coast.

Jan 2, 1969

By William F. Keyes

Greensand, which is widely distributed in the Eastern United States, was produced in 1975 only by Inversand Co., a subsidiary of Hungerford & Terry, Inc., near Clayton, N.J. Production and sales information are not available for publication. Raw greensand produced by the company was sold for agricultural use as a soil conditioner. Processed greensand was used by manufacturers as filter media in equipment for the removal of manganese, iron and other elements from water. The University of Delaware received a grant of $17,051 from the Bureau of Mines early in 1976 to continue its studies of the effectiveness of greensand in removing metallic contaminants from waste waters.

Jan 1, 1977

By J. A. Elliot

Deep Mix-in-Place soil stabilisation is achieved by forming columns of soil/cement arranged to overlap by secant intersection. Alternate columns are constructed initially and infilled. The cementitious material injected is designed to retard the strength of the resulting mix thereby allowing satisfactory overlapping. Columns are constructed using a designed large diameter mixing auger mounted on a smaller diameter auger stem. This is firstly screwed to the design depth removing only such spoil as to enable penetration of the auger, and subsequently counter rotated and extracted in a predetermined mixing pattern and grout injection rate to ensure continuous and homogeneous treatment through each successive level. The process is performed whilst monitoring auger depth, grout flow and pressure. Cementation Piling and Foundations Limited used this technique to stabilise allu­vium and to facilitate the construction, by conventional techniques, of a circular pumping station pit of 10M diameter to 10M below ground level. The work was carried out within 3M of adjacent domestic properties, and on a very restricted site in Elland, West Yorkshire. Ground conditions consist of 2M of cohesive alluvium becoming water bearing and increasingly sandy and gravelly with cobbles which overlies the mudstones at 10.0m depth. Sandstones beneath formed an aquiclude to artesian ground water with the underside of the open excavation approxi­mately 1.0M from the top of this material. Peripheral treatment into the mudstone, coupled with pressure relief wells, proved successful and final excavation depth was achieved in "the dry".

Jan 1, 1989

By H. O. McLeod, J. M. Campbell

Data analysis of pentane and hexane adsorption from natural gas in a fixed bed of silica gel shows that constant length mass transfer zones form, the curvature of the adsorption isotherm controls the growth of the mass transfer zone and surface diffusion of molecules inside the silica gel particle controls the mass transfer rate. Curvature of the hexane isothem is more than the curvature of the pentane isotherm. Because of this curvature the hexane adsorption zones reached a constant length. In contrast, the pentane adsorption zones were always increasing in length during each run. A procedure was developed to obtain correct mass transfer coefficients using effluent curve slopes. These transfer roefficients increase with the amount of hydrocarbon adsorbed on the silica gel particle. The characteristic shape of the hexane effluent curves also show that molecular diffusion inside the silica gel particle controls the adsorption rate of pentane and hexane. INTRODUCTION The purpose of this study was to determine the mechanisms that control the dynamic adsorption of hydrocarbons from a natural gas onto silica gel. Before one can deal effectively with multicomponent adsorption, the transfer mechanisms by which a single hydrocarbon component is adsorbed from the gas stream must be defined. Two principal investigations of this system have been published ' and indicate that diffusion through the gas around the particle controls the adsorption rate. Some of the experimental observations in each study either do not support this transfer mechanism or are inconsistent with the mathematical model used in analysis. In this study surface diffusion of molecules inside the particle controls the mass transfer rate of pentane and hexane. This mechanism is indicated by the effluent curve shape for a constant length transfer zone and by the variation of the mass transfer coefficient with concentration of the adsorbed hydrocarbon. THEORY AND DEFINITIONS — MATHEMATICAL MODELS Mathematical solutions for the isothermal adsorption of a trace component from a carrier gas are derived from three relationships: the mass balance or continuity equation, the equilibrium relationship between the gas and solid phases, and a mass transfer rate equation. The transfer rate is proportional to the adsorbate concentration gradient within either the gas or solid phase. Mathematical solutions of these equations usually give the adsorbate concentration as a function of time and distance from the bed inlet. That part of the bed in which the adsorbate concentration changes from a maximum to a minimum value is called the transfer zone. This transfer zone is directly related to a plot of the effluent concentration vs time which has a characteristic S-shape. This general shape is determined by the continuity equation and occurs in many processes of diffusional transfer.

Jan 1, 1967

By John Corcoran

INTRODUCTION Content of this Report The 1300m long twin-bore 8.1m diameter Airside Road Tunnels (ART) were excavated beneath the busy taxiways and stands of Heathrow Airport between 2002and 2003. The tunnels were fully completed and handed over to the client for use early in 2005. This paper will describe the purpose of the tunnels, and the measures put in place to minimize the impact of construction on the daily activities involved in running an international airport. Terminal 5 Construction Heathrow Airport is the busiest international airport in the World, with a current capacity of circa 67 million passengers per year, based on existing infrastructure of4 passenger terminals, 1 cargo terminal, 2 runways and 170 aircraft stands. Terminal 5(T5) is being built to increase Heathrow’s passenger capacity by providing the following: 12 additional aircraft stands through redevelopment of the south apron area, in the autumn of 2004 A main terminal building (T5A) and a first satellite (T5B), and 43 additional stands by the spring of 2008, most of which will be able to receive the new generation large aircraft (Airbus A380) A second optional satellite (T5C) by year 2010 A third optional satellite (T5D) by year 2015 The total value of the project is approximately 4.2 billion pounds for the main phase of the works spanning from 2000 to 2007. Purpose of the Airside Road Tunnel The ART has been constructed to support the internal road traffic of the airport between terminals, aircraft stands, runways and taxiways, for passenger buses, service and technical vehicles. The majority of the traffic will be buses transporting passengers between the terminals and their aircraft.

Jan 1, 2005

By E. Kuipa, J. N. Lekunze

The selection of an underground mining method stems from a multivariate analysis that considers geomechanical, geological, economic, and operational parameters. Even after identifying the most compatible method, there is no assurance that the mining company will achieve the best performance. The geological complexity of some deposits requires adaptations of methods described in the literature to obtain more selectivity and reduce mining waste. There are some studies on geometry of underground structures, but a methodology that describes an adaptation of a room-and-pillar mining method for ore bodies with down-dip varying from 20° to 25° is novel. The present work aimed to reduce dilution by adapting the traditional room-and-pillar mining method (TRP) to inclined ore boLittle attention has been paid to the rehabilitation of derelict and ownerless mines in South Africa after their lifespan. This paper aims to explore management gaps in legislation that have resulted in the non-rehabilitation of derelict and ownerless mines in South Africa. There is growing evidence that supports the distressing effects of mining on people living around these mines in the North West Province. This paper was motivated by the current socio-economic status quo of old mining towns, the influx of illegal miners (Zama Zamas), severe environmental damages, and the violence associated with derelict mines. Underpinning this research was an ecosystem approach and integrated resources management principles, which formed the foundation for the decision-making process.The researcher used a mixed-method approach and employed convergent techniques. A semi-structured instrument was used to collect data from 200 respondents. The results indicated that there is a dire need for community-based consultative processes, and an absence of clear guidelines for derelict and ownerless mines to pressure mine management to adhere to rehabilitation standards. Moreover, the mining charter is ambiguous regarding policy implementation, budgetary allocation, and duration of the rehabilitation of these mines. The paper concluded that management challenges associated with derelict mines can be reduced if all stakeholders follow the guidelines as outlined in the environmental legislative framework (NEMA) of South Africa while being open to innovations in line with international best practices. It also contributes towards the development of guidelines for the management and implementation of legislation related to derelict and ownerless mines in South Africa from a philosophical, theoretical, and policy perspectivedies. This new method is entitled short-hole room-and-pillar (SHRP). The equations that measure the dilution are defined according to the geometry of stopes and openings. The results comprise comparative analyses of the operational and planned dilutions to measure the performance of the SHRP method. The average operating dilution of the SHRP method was more than five times lower than the planned dilution according to the TRP method. Low operational dilution indicates high selectivity of the method and its potential to reduce underground mining tailings.

Oct 9, 2024

By L. F. Contreras

In open pit mine design, it is customary for geotechnical engineers to define the appropriate slope design angles within practical limits. The conventional approach to slope angle design is based on the comparison of calculated stability indicators, such as the factor of safety (FS) and the probability of failure (PF), with generic acceptability criteria not directly related to the impacts of failure. A major drawback of this type of approach is related to the difficulty of defining meaningful acceptability criteria. An alternative methodology of pit slope design is proposed, where the economic impacts of potential slope failures are calculated and used as the elements on which to apply the acceptability criteria for design. The methodology is based on the construction of a graph, referred to as a risk map, that relates the probability of exceeding the economic impact of slope failure to the magnitude of the impact measured in monetary terms. The process includes the analysis of a selected number of representative years of the mine plan and slope sections of the pit areas to define the required inputs for the construction of the risk map. The paper discusses the concepts used in interpreting the probability of slope failure, and describes the approach followed for the estimation of the economic impacts of slope failure and the construction of the risk map. Finally, the two main uses of the risk map are discussed, including the comparison with acceptability criteria for the evaluation of a specific open pit design and the comparative analysis of open pit design options in terms of value and risk to identify optimum pit layouts.

Jan 1, 2015

By J. M. Galera, M. D. Rodriguez, V. Pozo, S. Cooper

"Cobre Las Cruces mine extracts copper minerals from a VMS deposit located in the well-known Iberian Pyrite Belt (IPB). As an open pit, it is distinguished geologically from other IPB mines by the presence of around 150 m of Tertiary soft marls, known locally as the Guadalquivir Blue Marls, followed by a regionally important aquifer. Below the marls and aquifer the mineralization is hosted by rocks typical of the Palaeozoic within the IPB, comprising gossan, tuffs, slates, and sulphides.This combination of a substantially soft rock and more competent, older (but still occasionally problematic) Palaeozoic lithologies constitutes a unique geological framework and presents substantial challenges in maintenance of slope stability, and therefore operational safety, at the mine site. This paper describes the fundamental design, excavation, and monitoring measures implemented at the mine to maintain safe production, and the lessons learnt during the mine development. IntroductionAs a modern Spanish mine, Las Cruces is committed to the use of best available technology and practices with the aim of guaranteeing the production of ore in a safe environment. From a practical perspective, this implies the realization of a high quality pit design, ongoing geotechnical mapping of exposed slopes to ensure conformity with design, and use of leading geotechnical surveillance technology to complement visual observations. The focus of this article is to illustrate how, at a mine site with potentially problematic soil/rock conditions, multiple advanced techniques employed from design stage analysis through to final pit configuration and vigilance, were combined to achieve an overall control of the ground conditions. In Figure 1 the layout of the pit is shown, illustrating development at the beginning of 2015."

Jul 1, 2019

By C. Pelley, S. Kelebek, G. Kunzel, S. Gregersen, M. Pollanen

A series of small-scale tests was conducted to evaluate the effect of micro-fracture development, imposed by blasting, on the material properties of the rock as well as its resistance to crushing and grinding. The uniaxial compressive strength, tensile strength, Poisson’s ratio, Pwave, S-wave velocity, point load test index, crushing, and grinding work indices were evaluated for samples without any blasting load and for samples which had received a variety of blast loads ranging from a single impact with a lowstrength detonating cord to a combination of impacts at different times and significant impacts with powder factors close to those used in practical blasts. It was shown that the rock mechanics parameters change even at low impacts, suggesting easier crushing of the rock. Damage values appear to be affected by timing as stress wave superposition affects the damage process. Fragmentation is achieved at higher impact levels while work index modification of the fragments is also observed when high powder factors are used, suggesting improvements in grinding.

Jan 1, 2006

By Frank B. Fulkerson

Aluminum production in the Pacific Northwest has a new potential for expansion and increased stability of operation. This new potential results from greater availability of power; lower freight rates on alumina and aluminum; good market prospects for the metal, including western aluminum market expansion following a decline in defense requirements in the 1950's; and possibility of developing bauxite deposits in the Pacific Basin as well as other mineral resources. INTRODUCTION This is a report of a special study by the Bureau of Mines of the primary aluminum industry of the Pacific Northwest. It outlines developments relative to the United States as a whole.

Jan 1, 1962

Test Work on High Throughput Diamond Tracer Recovery from Alluvial Recovery Tailings with a Containerised Optical Sorter Under Real Production Conditions Worldwide alluvial diamond deposits are traditionally processed with dense media separation and XRF sorters, hand picking or grease tables. The test work conducted verifies the performance of an optical sorter detecting the transparency of particles for diamond recovery from the DMS concentrate, eg XRF-sorter and handpicking tailings. The containerised setup enables economically feasible, high throughput, semi-mobile setups to retreat recovery tailings from alluvial and also primary deposits. The test work has been conducted with quartz and glass particles, which are less transparent or comparably transparent, under realistic production conditions on a 600 mm belt machine with an installed electrical power of only 21 kW. The results show that 99 per cent recovery can be reached at a throughput of 10 t/h in the -8 + 2 mm fraction and at 22 t/h in the -25 + 8 mm fraction. At a throughput of 18 t/h a recovery of 88 per cent has been assessed. At a further escalation of the throughput, dust in the sorter container made sorting impossible in the coarse fraction and the recovery decreased significantly in the fine fraction. Analysis of the belt coverage indicates that higher throughputs of the coarse fraction can be fed onto the optical sorter if the dust extraction system is improved. The results are basis for the decision to conservatively feed 20 t/h of the coarse fraction and 17 t/h of the fine fraction in day to day production. The settings have been applied to sort alluvial recovery tailings in South Africa and will be applied to sort the recovery tailings of a primary deposit in Lesotho. The test work has shown that an optical sorter can be used to retreat recovery tailings with high throughputs. The compact setup of a screen and a 9 m standard container enables semi-mobile, temporary setups for small recovery tailings dumps and remote areas. In addition, sorting on transparency ensures the recovery of high value low-fluorescent diamonds.

Sep 13, 2010

By Scott Chesman

Increased TBM performance is leading the way for resurgence in tunneling activity in NYC. Tunnels will be excavated in the same geologic formations as previously excavated D&B tunnels whose construction records are providing valuable insight into the prediction of rock mass behavior. This report compares an eight mile stretch of NYC Water Tunnel #2 with the recently excavated eleven mile stretch of the TBM driven Water Tunnel #3. Comparisons of the type and amount of rock support installed as well as water inflows and grout quantities are made. Rock mass characteristics specific to TBM performance are also evaluated.

Jan 1, 2005

By S. Asokan, D. Rathod, Ch. V. G. K. Murty

Tata Steel, a steel arm of Tata Group, is Asia's first and India's largest integrated private sector steel company. Tata Steel’s turnover in fiscal 2004-05 was nearly US$ 3.25 billion. As part of its vision to grow in related industries, Tata Steel is poised to enter the Titania businesses in the Indian state of Tamil Nadu. The Titania project will involve mining, separation of ilmenite & other co-minerals, beneficiation of ilmenite to synthetic Rutile and further maximum value addition to Titanium metal. This paper outlines the journey from the concept to current findings of the Bankable Feasibility Study in developing Sattankulam Heavy Mineral Sands Deposits in the State of Tamil Nadu, India by Tata Steel.

Jan 1, 2005