Search Documents

By Mavor S.

Further discussion at the Mining Institute of Scotland's general meeting held in Edinburgh, 12 February 1916, with D.W. Mowat, president, in the chair, of a paper published in Trans. Inst. Min. Engrs., 1915, vol. L, p.625 and discussed vol. L, pp.92, 433, 468, and 704 included comments by Mowat D.W. and the author's reply

Dec 1, 1916

By Wilbert J. Huff

The organization of the Explosives Division is indicated by the accompanying chart (fig. 1). As this has been discussed in a previous report3/, it will not be considered further in this report. The activities of the various units are outlined below. I. INFLAMMABILITY OF GASES AND VAPORS4/ Determination of the Explosion Hazards of Combustible Gases and Vapors Found in Mines and Industries The Explosives Division maintains, at the Pittsburgh Experiment Station, a laboratory specially equipped for the determination of the explosion hazards of combustible gases and vapors. Of particular importance, is the determination of the chemical composition within which explosions may occur and beyond which there is no danger of explosion, combustion or inflammation. These limits, known as the limits of inflammability, as determined by this and other laboratories, have been compiled in Bulletin 279 of this Bureau. The last revised edition (1931) of this bulletin has been exhausted. Since it was published, the Pittsburgh laboratory has determined the limits of about 40 combustibles and has ascertained more precisely ant accurately many previously published limits.

Jan 1, 1938

By J. Philip Neal

Feldspar is no example of special mineralization in isolated spots: it can usually be found within a mile or so of almost anywhere. Along with silica sand, it is a major part of our world's total mineral composition. This fact imparts to it an economic status different from a sulfide ore, or potash, or phosphate. While every feldspathic "stringer" does not possess economic potential, the generous distribution does yield a high statistical frequency of good feldspar ore bodies: the adjective "good" being subject to some flexibility of interpretation. The strong chemical bonds of this alkali aluminum silicate give it certain use advantages, but under present technology its individual elements cannot practically be separated to create aluminum, potassium, sodium, silicon - or their oxides. Its present uses rely upon chemical inertness - as in fillers; and on its physical melting characteristics and their effect in glass, enamel, or ceramics.

Jan 1, 1973

By Luis Romero, Edilberto Linares, Steve Windle

El yacimiento de Zafranal —proyecto de pórfidos de cobre y oro ubicado en la región Arequipa, Perú— en sí mismo ha penetrado en lo que parece ser un salto dextral sobre una estructura del SFIC. A nivel de yacimiento, se ha mapeado una serie de fallas pronunciadas WNW en la zona mineralizada principal, consistentes con la transtensión dextral inferida. Esta estructura de fallas se trazó en 3-D a partir de las zonas de gubias identificadas en la fotografía de testigos, método que permitió elaborar un modelo estructural de forma rápida y con consistencia interna. La cinemática de las vetas y los patrones de afloramiento trazados generalmente coinciden con las estructuras interpretadas. El movimiento dextral inferido en el SFIC en el Cretácico Superior es consistente con un vector de convergencia de placas hacia el norte, y puede ser utilizado para identificar targets estructurales para sistemas de edad similar, tanto en el piamonte como en la cordillera.

Dec 31, 2019

By Richard Paul Seelig

The following review covers published information on pressing of metal powders at room temperature. Only those operations are considered which occur between the time the powder is filled into the cavity and the compact is ejected from the die. Thus, this review does not concern hot pressing, coining or sizing feed or flow problems, commercial presses nor designs. It was also necessary to disregard to a large extent the effect of pressing on subsequent operations and on properties after sintering. 'The pressing operation is considered independently in its function to compact loose metal powder into useful shapes which can subsequently be handled. There are some comments by the writer in connection with a few of the findings quoted in the literature in order to stimulate thought and discussion. The selection of references quoted in the text is in some cases arbitrary although an attempt was made to favor papers containing novel ideas, techniques or results which mag stimulate future research. In order to enable the reader to check further into the subjects mentioned, the original, rather extensive, bibliography is appended even though not all the references are touched on in the printed version of this review. The equipment used by various workers, for example a die design created by Bridgman,22 is very interesting. 'The die insert has a conical external surface. The vertical pressure exerted on the punch transmits itself to the die which in turn is pushed harder into its tapered retainer. Thus, the higher the pressure exerted on the punch, the higher also the pressure exerted inwards on the die inserts. Inasmuch as this pressure counteracts the internal pressure from the compact the two stresses balance each other so that it is possible to obtain tremendous pressures without breaking the die. The die collar was made from an oil hardening tool steel, heat treated to a tensile strength of some 300,000 psi. The die was closed at the bottom by a plug made from special tool steels. Bridgman found that there is no steel which will withstand a com-pressive stress of 700,000 psi without continuous slow flow or immediate fracture. Therefore, the only material suitable for use in the pressing punch was sintered carbide. In view of the ingenious design it was possible to use special tool steel as die material. Jones22 raises the question whether this method of pressing has practical application in powder metallurgy. Although these tremendous pressures cannot readily be utilized without many special precautions, the tapered die and retainer idea is believed to be useful even for lower pressures. Bridgman, himself," alls attention to the fact that the properties

Jan 1, 1947

By Richard Paul Seelig

The following review covers published information on pressing of metal powders at room temperature. Only those operations are considered which occur between the time the powder is filled into the cavity and the compact is ejected from the die. Thus, this review does not concern hot pressing, coining or sizing feed or flow problems, commercial presses nor designs. It was also necessary to disregard to a large extent the effect of pressing on subsequent operations and on properties after sintering. 'The pressing operation is considered independently in its function to compact loose metal powder into useful shapes which can subsequently be handled. There are some comments by the writer in connection with a few of the findings quoted in the literature in order to stimulate thought and discussion. The selection of references quoted in the text is in some cases arbitrary although an attempt was made to favor papers containing novel ideas, techniques or results which mag stimulate future research. In order to enable the reader to check further into the subjects mentioned, the original, rather extensive, bibliography is appended even though not all the references are touched on in the printed version of this review. The equipment used by various workers, for example a die design created by Bridgman,22 is very interesting. 'The die insert has a conical external surface. The vertical pressure exerted on the punch transmits itself to the die which in turn is pushed harder into its tapered retainer. Thus, the higher the pressure exerted on the punch, the higher also the pressure exerted inwards on the die inserts. Inasmuch as this pressure counteracts the internal pressure from the compact the two stresses balance each other so that it is possible to obtain tremendous pressures without breaking the die. The die collar was made from an oil hardening tool steel, heat treated to a tensile strength of some 300,000 psi. The die was closed at the bottom by a plug made from special tool steels. Bridgman found that there is no steel which will withstand a com-pressive stress of 700,000 psi without continuous slow flow or immediate fracture. Therefore, the only material suitable for use in the pressing punch was sintered carbide. In view of the ingenious design it was possible to use special tool steel as die material. Jones22 raises the question whether this method of pressing has practical application in powder metallurgy. Although these tremendous pressures cannot readily be utilized without many special precautions, the tapered die and retainer idea is believed to be useful even for lower pressures. Bridgman, himself," alls attention to the fact that the properties

Jan 1, 1947

By Yuemin Zhao, Wenxuan Liu, Maoming Fan, Zhanyuan Long

"Coal is mainly composed of energy-producing elements carbon and hydrogen. In addition to these elements, coal usually contains many other valuable elements, including iron, aluminum, silicon, rare earth elements, lithium, gallium, germanium, vanadium, uranium, titanium, scandium and phosphorus. These coalassociated elements are significantly enriched in coal combustion byproduct fly ash because the majority of the main components, carbon and hydrogen elements, being removed. Table 1 provides the chemical composition range of the main element oxides in 12 Chinese fly ash samples collected from coal power plants located in Northeast China, Northwest China, Southwest China and Southeast China. It can be seen from Table 1 that the major mineral components of different ashes are similar, but the bulk chemistry of different fly ashes may vary due to the changes of ratios of the mineral components in different coals. The major mineral components in various Chinese coal combustion fly ash are silicates, iron oxides and unburned carbon.Chinese coal fly ash usually contains about 5 to 15 percent of unburned carbon, which are generally chars with irregular shapes and wide particle size distribution. In addition to unburned carbon, XRD analysis of four Chinese fly ash samples from Liaoning, Shanxi, Guizhou and Shandong provinces indicates that the fly ash samples are composed of minerals such as quartz (SiO2), mullite (3Al2O3.2SiO2 or 2Al2O3.SiO2), hematite (Fe2O3), maghemite (gamma form of hematite, ?-Fe2O3) and magnetite (Fe3O4). The mullite and quartz particles are usually present as spherical particles because they are formed by melting clays, feldspars, quartz, calcite and other common minerals in coal during coal combustion. The silicate particles have usually entrapped gas to yield hollow spherical particles because their lower melting point facilitates gas entrapment.The iron oxides are usually spherical also. The magnetite (Fe3O4) is derived from pyrite (FeS2), hematite (Fe2O3), siderite (FeCO3) and limonite (2Fe2O3.3H2O) in the coal. Maghemite (?-Fe2O3) is formed by dehydration of the mineral hydrohematite (?-FeO(OH)) and/or oxidation of magnetite (Fe3O4) during coal combustion. Maghemite (?-Fe2O3) and magnetite (Fe3O4) are strongly magnetic, so they are recovered from Chinese coal fly ash and widely used for coal processing in China (Fan et al., 2005, 2000)."

Jan 3, 2018

By George S. Rice

In 1911 the Director of the United States Bureau of Mines instructed the chief mining engineer of the bureau , during an investigation of coal-mine safety conditions in Europe, to ask the directors of the various mine-experiment stations whether they would favor a European conference . The majority of the officials in immediate charge of experiment stations favored the plan , and Victor Watteyne, inspector general of Belgium, suggested that the United States call such a conference to be held immediately after the Eighth International Congress of Applied Chemistry, which was to assemble in New York on September 3, 1912 . Accordingly, invitations were issued by the United States Government to those countries having mine-experiment stations , namely, Austria-Hungary, Belgium, France, Germany , and Great Britain, and to those that contemplated the establishment of such stations , Canada and Mexico . All but Great Britain and Canada accepted ; Mexico designated a representative , who later found it impossible to come. The Government of Great Britain in declining, expressed regret at its inability to accept ; an informal statement was made that the opening of the experimental gallery at Eskmeals , England , occupied the attention of the officials in charge . Delegates were appointed by their respective Governments as follows: Austria-Hungary, Julian Czaplinski , royal mining engineer. Belgium, Victor Watteyne , inspector general of mines . France, J. Taffanel, director of the Lievin experiment station . Germany, Carl Beyling, bergassessor, director of Dortmund experiment station. United States , Charles E. Munroe, consulting explosives expert and George S. Rice, chief mining engineer of the Bureau of Mines . Subsequently Mr. William O'Connor , a mining engineer and mine operator of Wales , who opportunely appeared at the Pittsburgh station with letters of introduction from the South Wales Institute of Engineers and from prominent mining officials of Great Britain , was unanimously invited to take part in the meeting as an unofficial representative of Great Britain . Messrs . Beyling, Taffanel , and Watteyne were met in New York on September 3, by George S. Rice, who accompanied them to Washington, where they were welcomed by Director J. A. Holmes , of the Bureau of Mines , and where , with the delegates to the Eighth International Congress of Applied Chemistry , they were presented to President Taft . Mr. Taffanel was unfortunately called back to France just before the scheduled time of the conference on account of a mine disaster ; the other delegates , including Mr. Czaplinski , convened at Pittsburgh on the morning of September 14. Mr. Rice, representing the Director of the Bureau of Mines , acted as temporary chairman , and called the meeting to order.

Jan 1, 1914

By AIME AIME

THE John Fritz Gold Medal for 1929 was presented to Herbert Hoover at the Executive Mansion on April 25, at a luncheon given by Mr. Hoover to present and past members of the Board of Award, preceding medalists, and presidents and secretaries of the American societies of Civil, Mining and Metallurgical, Mechanical, and Electrical Engineers. The presentation party of forty engineers which gathered at the White House, from all parts of the United States, was made up of past presidents of the four senior national engineering societies that established the John Fritz Medal and included five men who had received the medal in previous years. These former medalists were Edward Dean Adams, J. J. Carty, J. Waldo Smith, Elmer A. Sperry and Ambrose Swasey. This medal is the highest honor bestowed by these four national engineering societies, having a membership of 60,000. It is awarded not oftener than annually for "notable scientific or industrial achievement, without restriction on account of nationality or sex." In accordance with custom, the award to Mr. Hoover was made tentatively and without announcement in October, 1927, and was formally con- firmed and announced one year later.

Jan 1, 1929

By B. M. O'Harra

Zinc smelting is frequently termed a ba.ckward art. The term is hardly true, for great progress has been made in recent years in the design and in the thermal efficiency of the retort furnace, in the quality of retorts, in the recovery of zinc, and in the ability to treat more impure and complex ores. The fact remains, however, that the peculiar physical and chemical properties of zinc have delayed such immense advances-large smelting units, high recovery, lowunit costs, and ability to treat low-grade ores-as have been made in the metallurgy of lead and copper. In current retort-smelting practice, the ores, if carbonates, are calcined to remove carbon dioxide; or, if sulphides, are roasted to remove sulphur. The sulphur must be eliminated as completely as possible, usually to less than 1 per cent. This means that the roast must be continued for a long time at a high temperature, with resulting high cost and small capacity per furnace. The roasted ore is mixed with about 50 per cent of its weight of reducer, which may be fine coke, anthracite, or nonbituminous coal. This mixture is charged into horizontal fire-clay retorts. The retorts used in this country are about 8 inches in internal diameter by 4 feet in length and hold 50 or 60 pou~ds of ore. The diameter of the retort is limited by the tirrie required for the heat to penetrate to the center of the charge; the length by the strength of the retort, which at the high temperature employed can not support the weight of the charge if the span is more than about 50 inches. The retorts are heated externally by coal, natural gas, qr ·producer gas to a temperature of 1,200° C. or more. The zinc oxide is reduced to zinc, which is volatile at this temperature, and passes into a conical fire-clay condenser. attached to one end of the retort, where it conde_nses to liquid zinc and is removed. Twenty-four hours are required for distillation, and because of the low heat conductivity of the retort walls 11.nd of the ore charge itself, the heat efficiency even of the most modern regenerative furnacei;; is only about 12 per cent. The retorts have a short life, 30 to 6Q days, at the high temperature required-; zinc losses are heavy, usually 10 per cent or more; and the proportion of impurities in the retort charge must be carefully controlled to prevent the rapid corrosion of retorts. For these reasons, much work has been done in an e:ff ort to, find cheaper and more efficient methods o.f recovering zinc from its ores. Various methods have been proposed for smelting in the blast furnace. Some of these contemplated the production of zinc vapor and its condensation to liquid; others attempted to produce liquid zinc directly by smelting under pressure. It is now realized that fundamental difficulties render these proposals impracticable. The electric furnace for smelting offers obvious advantages in the way of the efficient utilization of energy, large units, easy attainment of high temperatures, and the possibility of treating complex ores. E. H. and A. H. Cowles first suggested a design for an electric furnace for the reduction of zinc ores and patented their process in 1885. Their attention was soon directed to other uses for their furnace and nothing further of importance was done in the electric smelting of zinc until about 1900. Several investigators then started work upon various processes and had more or less success. The chief difficulty they encountered was the impossibility of obtaining more, than a small amount of the zinc as liquid metal because most of the zinc vapor condensed as blue powder. Interest in the electrothermic metallurgy of zinc increased, many patents on processes and furnace design were taken out, and the literature on the subject grew, until in 1914 and 1915 the problem seemed to be approaching solution. About this time the hydrometallurgy of zinc, the development of which had been lagging somewhat behind that of the electrothermic metallurgy, sprang into the limelight and a commercial process was soon perfected. This rapid development, perhaps aided by the war premium on the high-grade spelter produced by electrolytic deposition, distracted attention from electric smelting to some extent, though progress continued. With the perfection and standardization of the electrolytic process has come a better realization of its limitations, especially the necessity for large-scale operation ·and the difficulty of obtaining high extraction. Because of these limitations the electrothermic metallurgy of zinc still has a field of its own and in fac-t promises to become a strong competitor of both hydrometallurgy and retort smelting except under conditions highly favorable to the latter methods. Because of the imperfections of the retort and electrolytic processes and the promise that the electric furnace offers in overcoming these imperfections, the. United States Bureau of Mines, in cooperation with the Missouri School of Mines and Metallurgy, has undertaken a study of the electrothermic metallurgy of zinc.

Jan 1, 1923

By G. B. Shea, R. A. Cattell

This resume of the work of the Petroleum and Natural - Gas Division of the Bureau of Mines for the fiscal years 1940 and 1941 is the second of a series. of progress reports . It brings forward from the 1939 annual report information on the course of activities of the division in carrying out its objectives of increased conservation and better utilization of petroleum, natural gas, and related resources through a coordinated program of research and fact - finding . It discusses, also, special assignments. executed for other Government agencies, which in recent years have constituted a considerable part of the division's work ." . In the present national emergency, in which petroleum is so essential , many of the Bureau's research activities bear directly on the availability, conservation, and use of petroleum for national defense . Accordingly, during the past year attention has been focused for the most part.on.problems associated with the needs of national defense . Several long-time researches , which in themselves are potential sources of desirable knowledge , were judged to be of secondary importance under present conditions and accordingly were suspended . Studies also were oriented in line with rapidly changing conditions to meet the demand for accurate findings on short notice . The Petroleum and Natural - Gas Division has experiment stations at Bartlesville , Okla . , and Laramie, Wyo . , a field office at Dallas , Tex . , and a field office and laboratory at San Francisco , Calif . It also operates the Government helium plant near Amarillo , Tex. In addition to the helium operations , some of the petroleum and natural - gas research activities are conducted at the Amarillo plant .

Feb 1, 1942

By S. Grogan

Next year marks the tenth anniversary of the Surface Mining Control and Reclamation Act (SMCRA). As the U.S. coal industry scrambles to cope with serious economic difficulties, it is appropriate to examine some other difficulties that have their origin in certain provisions of that ten year old law, and that bear directly on the economic viability of surface coal mining in the west. This paper focuses briefly on three technical issues in the reclamation of surface coal mines in arid regions, and suggests that innovation can resolve these issues. The coal industry operates within a narrow legal context, defined in 1977. In enacting SMCRA, Congress listed among the purposes of the Act ?... to...strike a balance between protection of the environment, agricultural productivity and the Nation's need for coal as an essential source of energy." I maintain that such a balance has never been struck, particularly with regard to the reclamation of mines in the west. One reason is that when SMCRA was enacted its supporters were aware of uncertainties about the potential for successful reclamation of western surface mines. Over the intervening years, as a recent Congressional study report (OTA, 1986) points out, "...the risks these uncertainties may pose to the long term success of western reclamation have been reduced significantly." Unfortunately, SMCRA's enforcement agency, the Office of Surface Mining (OSM) has not yet recognized this fact, and the western coal industry is paying the price.

Jan 1, 1986

Senior staff representatives of the Bureau of Mines and the National Institute for Occupational Safety and Health (NIOSH) met in Washington on September 6, 1972, to review and evaluate their cooperative accomplishments to date and to consider the planning and conduct of future coordinated activities. The six presentations given at this joint staff seminar are published here for the benefit of those concerned with the problems of coal mine health, and especially those with responsibilities in administering the Coal Mine Health and Safety Act of 1969.

Jan 1, 1972

By E. H. Denny

The presence in the Cripple Creek district, Colo., of irrespirable gas or gases, generally known to consist mainly of nitrogen and carbon dioxide, has been recognized by members of the mining industry in that region almost since underground mining was begun there; the occurrence, origin, and possible control of these gases have been discussed in several articles cited at various places in this report. Similar gases have also been studied in other metal-mining districts, as later discussed. In March, 1925, there were two fatalities from rock-strata gases in the shaft of the Index mine, near Cripple Creek. Two men repairing the bell or signal line preparatory to reopening the shaft were lowered into irrespirable gases and died. Their bodies were recovered by rescue crews from the United States Bureau of Mines and .the Portland mine, Victor, Colo. These crews found it necessary to use oxygen breathing apparatus. In October of the same year a miner was trapped on the 6 level of the Midget mine by an influx of gases that filled the shaft to a point above that where he was working. Oxygen breathing apparatus was again used by Bureau of Mines employees, who were in the vicinity, and the man was brought out in time to save his life. These two fatalities and one near fatality seemed to show that additional investigation of the gases and methods of control might be warranted. Accordingly, field and laboratory studies were begun by the authors of this report after a visit to the district by M. van Siclen, then engineer in charge, mining research division, Bureau of Mines, and after conferences with the Mine Owners' Association of Cripple Creek and with J. T. Joyce, metal-mine commissioner of the State of Colorado. The mine operators of the Cripple Creek district and the State mine commissioner's office gave whole-hearted cooperation in this work.

Jan 1, 1930

By H. J. Wasson

WITH the close of 1932 and the third year of the depression, the activity of oil production presents, amidst the general wreckage and chaos of industrial society, a somewhat unique picture of rationalized economic effort. East Texas still dominates the contemporary horizon, but it has become, at least for the time being, a definitely known factor. With its 9500 wells it is approximately 90 per cent drilled up. So long as production control obtains, it is merely one important factor of the national oil reserve. Each succeeding month of stabilized production tends to lull the industry's fears and the menace, both actual and psychological, of this giant field becomes ever more remote.

Jan 1, 1933

By AIME AIME

WITH the recent increase in the price of gold, its economic recovery at depths formerly considered impractical has become a present possibility. Two important difficulties must be met: pressure bursts of the rock, and the reduced efficiency of human labor subjected to the higher temperatures and the increased humidity at the greater depths. In the following abstract of a paper by J. H. Dobson, presented before the South African Institution of Engineers on

Jan 1, 1935

By Joseph Jensen

MANY fields have been zoned by nature with shales and intermediate waters between oil zones. Limitations thus imposed have been the basis on which the field was developed. In contrast thereto, in the Ventura Avenue Field, nature proved more generous. Always expecting to find such similar limitations, operators drilled deeper and deeper into the oil zone without finding any distinctive shale bodies other that the Gosnell shale and only one intermediate water, which became the point below which the final water shut-off of each well was made. Thus, on top of the structure, about 3300 ft. of oil-bearing zone has been penetrated below this intermediate w9ter-a distance of 4000 ft. below the Gosnell shale. At first it seemed that the greater the penetration in the zone, the better the well. The error of this assumption became evident

Jan 1, 1930

By F. Y. Kang

There are rich resources of natural graphite in China. It would be a good opportunity to upgrade national graphite industry if natural graphite with modification is used in lithium ion battery. Micro-crystalline graphite in high purity was coated with a carbon film on the surface. The initial cycle efficiency was improved to be 89.9% and cycle stability was remarkably improved. The experiments proved that microcrystalline graphite with carbon coating have excellent electrochemical performances at low cost as anode materials for lithium-ion battery. In addition, H2SO4-GIC technique was used to prepare the natural flake graphite powders with mild-exfoliation. Sub-micro and nano pores were found in the graphite samples. In correspondence the reversible capacity, rate capacity and cycle life were improved, which would meet the demand of high-power lithium-ion battery. Natural graphite is the most promising anode material for large-scale lithium-ion batteries. The demand of modified graphite grows up greatly in the market. Microcrystalline graphite with surface coating and flake graphite with mild-exfoliation are the promising commercial anode materials for the industry of lithium ion battery.

Jan 1, 2014

By R. L. Dunsmore

Introduction If one had been called upon to describe petroleum oil refining seventy-five years ago, he could have acceded to the request quite satisfactorily in about fifteen minutes. Fifteen years ago, an hour and a half would have been sufficient to give a general idea of oil refining, and of the equipment used for this purpose. Today, so extensive has been the research into all phases of the refining and manufacturing of petroleum products, and so rapid the strides in improvement in technique and equipment, that I doubt if a week would suffice to give an adequate outline of ail the ramifications of present-day oil refining. I propose to only 'hit the high spots', dealing particularly with the equipment and methods employed at the Imperoyal refinery, which you are to visit. Crude oil, the refiner's raw material, contains essentially only two elements, hydrogen and carbon. These are not present in the free state but are combined in various proportions as 'hydrocarbons'. A given crude oil is not made up of just one hydrocarbon, but of myriads; some solid, others liquid, and still others gaseous at atmospheric temperature and pressure, ail dissolved one in the other. Moreover, the nature and the relative amounts of the several hydrocarbons vary very considerably in crude oils from different sources. That is, a 'crude' from Oklahoma will contain hydrocarbons not present in crude from Mexico, and is different again from the Venezuela crude. Not only this but oil in a certain well in, say, Peru may be differently constituted from that in a well half a mile distant from it.

Jan 1, 1931

Salaries for mining professionals have gone up substantially in the last two years across most vocations and there has never been a better time to enter the industry, in terms of career opportunities and salary packages. With so many offers on the table and companies outbidding each other to attract the best talent, many new professionals are being lured in by the big money, sometimes at the expense of a satisfying career and a sustainable lifestyle. What should we consider when accepting a new position? What are our values, and how do these drive our decision making? This paper examines our core values as people and makes some observations about what it takes to really succeed in the mining industry.

Jan 1, 2006