Search Documents

By C. Slotta, F. Charlier, P. Blomen

"Within the energy concept of the German government, the operating time of nuclear power plants was initially extended from about 8 to 14 years. It is planned, however, that every power plant will gradually be decommissioned until 2025 and that simultaneously the amount of renewable energies will successively be expanded. According to the political state, nuclear energy is a discontinued model. Looking at the global energy market, though, an obviously opposed development can be observed. At the moment, 443 nuclear power plants are running worldwide and further 62 facilities are being built. These about 500 nuclear power stations have to be supplied with nuclear fuel right now and in the future. The present paper will describe the worldwide use of nuclear energy, the extraction of the nuclear fuel uranium and in detail the available and predicted resources of uranium. The conclusion of the paper is the statement that uranium as nuclear fuel is no scarce resource but sufficiently available."

Jan 1, 2011

By T A. J Hopper, B J. Birt, K K. Trofimczyk

Nuclear magnetic resonance (NMR) has been utilised in the oil and gas industry for over 60 years. The technology was recently identified as having potential value in iron ore, where latent bound moisture may affect ore handling even after dewatering and extraction. The first step in introducing this technology to iron ore involved laboratory tests on drill core samples. These results established the parameters for a downhole borehole magnetic resonance (BMR) tool for iron-rich environments, which was subsequently developed. A major challenge involved shrinking what is a very large tool in the oil industry to a slimhole, lightweight, 1-man deployable mining tool.Of primary concern was the ability to measure the very fast transverse relaxation times (T2s) seen in the lab results on iron ore samples. Iron creates local field gradients that significantly decrease the T2 times. As a result, the BMR tool had to be able to measure T2s in the range of hundreds of microseconds, a level not required in clastic sedimentary formations. The choice of T2 cut-offs in iron ore is critical to successfully separating the free and bound fluids. The industry has typically focused on T2 cut-offs in clastics and carbonates, but not in systems with high iron content. Using core analysis results (poro-perm and NMR) we were able to verify the BMR response. The T2 cut-offs were determined from NMR core analysis and then applied to the logs so as to provide a continuous, calibrated permeability log.Field results that highlight the challenge involved in logging in iron-rich environments are presented, as well as some minimum requirements for a successful BMR log. Examples from boreholes in an active iron ore mine in the Pilbara iron ore province in Western Australia are presented, as well as explanations for how NMR data can be combined with bulk density logs to provide a continuous dry weight density log based on the original density-porosity equation from Alger et al (1963).CITATION:Hopper, T A J, Trofimczyk, K K and Birt, B J, 2017. Development of a slimhole downhole nuclear magnetic resonance tool for iron ore – some applications and limitations, in Proceedings Iron Ore 2017, pp 473–480 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By M. K. G. Vermaak

Spiral concentration forms a crucial part of gravity separation circuits. The application of process models in the operation of gravity separation circuits offers significant benefits in recoveries and grade control. Significant strides in the modelling of spiral concentrators have been made during the last couple of decades. Despite these advances in modelling techniques and models, application in industrial processes is not fully optimized. The adjustment of splitter positions to accommodate changes in the feed parameters is impractical and difficult, resulting in losses. In this work an optical method is employed to detect the concentrate band position as a function of operating variables. As expected, the results indicate a strong influence of the solids content and total heavy mineral (THM) feed grade on the predicted gangue-mineral interface. Viscosity modifiers indicated the band position to be sensitive to viscosity and therefore the slimes content. Validation on an industrial sample indicated the possibility of using this model in feed-forward control application.

Jan 1, 2008

By John C. Gagliardi, Walter K. Utt

The U.S. Bureau of Mines, in cooperation with Carter Mining Co., conducted vibration tests of four off-road vehicle seats. The purpose of the tests was to determine which seat provided the best vibration attenuation under laboratory conditions. Laboratory tests were constructed to simulate the mining vibration environment within the limitations of the test equipment. The acceleration test levels and corresponding response of the seats were low compared to IS0 2631's fatigue-decreased-proficiency time limits. Two of the seats employed mechanical suspensions and two seats employed air suspensions. The seats were tested using a 22,241-N (5,000-lbf) electrodynamic shaker. Mechanical suspension seats were tested with various preload-to-mass ratios (PMR's) and cushion densities. Air suspension seats were tested with various air pressure levels and seat cushion densities. Air suspension seats provided good vibration attenuation if pressurized greater than 552 kPa (80 psi). Mechanical suspension seats' attenuation performance decreased if the PMR exceeded 9.8. Seat cushions of lower density provided less vibration damping.

Jan 1, 1993

By Thomas M. Nasiatka

This report briefly describes the present state of the art and the technological highlights of tunneling from its inception to the present. The discussion is concerned primarily with tunnels driven through relatively competent rock for mine development and various civil purposes. In addition to pinpointing the major technological breakthroughs in tunneling, this report indicates their general effect on the speed of tunneling. The tunneling speeds are based upon data from approximately 80 tunnels listed in the appendix. These data include length; cross section shape and dimension; type of rock; tunneling method; method of breaking, loading, and transporting the rock; average linear progress rate; and cost in values during the period of construction. Most of the tunnels described have diameters of 15 to 30 feet.

Jan 1, 1968

THE choice of a pumping plant for the drainage of a mine is a matter of such importance that it is obvious that in a short paper it is impossible to go fully into the reasons governing the adoption of any particular type. The author, therefore, proposes to briefly discuss the methods.in vogue, and, as far as possible, to point out the advantages and disadvantages of the numerous systems. The probiem is of extreme importance to the mining engineer, and it appears that in the past sufficient thought has not been given to this branch, as shown by the numerous failures which are encountered.When water is met with in large quantities, the development of the mine depends upon the pumping plant to such a great extent that the most careful consideration should be given before deciding on any particular scheme for drainage. The pumpingplant in a mine should be looked. upon in the light of an insurance policy, and should be treated as such, care being taken that the premium is as low as possibl~, and to ensure this it is necessary that the most efficient plant be secured. Local conditions play such an important part ill the design of a plant that no hard and fast rules can be laid down. When the amount of water to be handled is small, and there is no possibility of any increase...

Jan 1, 1912

By M. Tangstad

Keywords: Pyrometallurgy, ROMA, Norway, furnace, fines The ROMA project is a competence project on optimizing the usage of raw materials and energy in the ferromanganese, silicon, and aluminium industries. One of the items investigated in this project is the effect of fines on the furnace, and the usage of agglomerates versus lumpy ore. From lab-scale experiments it is shown, that for the charge to agglomerate in the furnace, the charge has to be exposed to a temperature higher than about 1200°C, independent of fines content. The fines less than 1 mm also showed higher agglomeration properties, compared to 2?4 mm, which showed no agglomeration property at all. The properties of agglomerates are very dependent on the pre-treatment of the agglomerate. Sinter and pellets, which have been heated to high temperatures, show a better strength, but also a lower CO reactivity. Sinter also shows a lower melting temperature compared to the ore.

Jan 1, 2011

In most mines using presplitting the final excavated wall shows a zone of damage just below the crest and well defined presplit half barrels. The crest damage (surface dilation) zone varies and is added to by subsequent adjacent perimeter blasting operations. Keeping the preconditioning to a minimum is possible using the methods described in this paper, developed on several diverse and geographically distant mining operations to control crest dilation and preconditioning by presplitting in advance - not just laterally but vertically in advance. The first documented case (Delbridge, Marton and McSweeney, 2004) in the development of the concept was undertaken at AngloGold Australia Pty Ltd's Sunrise Dam Gold Mine (SDGM), located beside Lake Carey, some 730 km northeast of Perth, Western Australia. The mine had been developed in a series of cutbacks to a depth of over 300 m and began underground mining during the latter stages of open cut operations. This mine is fairly unique in that it utilised a single pass vertical presplit which initially extended over three bench heights and after the failure mechanisms were understood, over four benches. The presplit drilling for the three stacked benches started on the floor of the second bench so that any dilation was confined to the surface one bench above the crest and modified perimeter blasting was then developed to curtail damage from blasting adjacent to the new crest. The second case is based on a South African coal mine in the Witbank Coal Measures, 140 km northeast of Johannesburg, Republic of South Africa (RSA). It was important that blasting for optimal wall stability and minimal scaling was developed in advance. A dragline is scheduled to excavate the #2 seam midburden which is the lowest of the economically viable coal seams in the five seam Witbank Coal Measures. Mining of the overburden, coal and partings above the dragline midburden pass are by excavator and truck and each mining layer is individually blasted. The results of presplitting the midburden through the overlying coal seams and partings have provided a presplit with no surface dilation of the midburden crest and ensures any subsequent crest loss is solely due to blasting adjacent to the vertical presplit. Typical of all coal mines in South Africa only vertical presplits are used. Wall control is most commonly delivered by presplit blasting and one common sight after the dust clears is a ridge of broken blocks along the presplit row, usually with a main crack running between the presplit blastholes and often parallel cracks either side of the perimeter line. The surface rock strata or block structures have been dilated by the venting gases and shock waves. Decoupled, fully coupled, single or double deck charges are used depending on a variety of factors, anecdotal practices and perceived benefits. Preconditioning of the crest rock by blasting from above may not be visible to the naked eye (or non-existent in overburden in strip coal mines) but the high speed venting of explosives gases (and often the water in the presplits) preferentially follow existing cracks and structures because there is no developed presplit crack near the surface. This nearly always lifts, shifts and separates the surface structures and geological layers. Stopping the dilation by 'sacrificial' or 'in advance' presplitting has been shown to reduce the crest loss at both metal and coal mines. Drilling and presplit blasting through an upper level of bench or layer provides a degree of restraint to the target layer where the crest must be maintained and any damage caused by the venting gases will not cause concern as it is removed as planned, leaving a stable crest.

May 1, 2010

By T. Burchett, F. Stanley, K. McGough, G. Luttrell

The vast majority of U.S. coal preparation plants utilize screen-bowl centrifuges to dewater their fine clean coal products. In light of this popularity, researchers at Virginia Tech have engaged in a variety of laboratory and industrial field test programs to develop technological enhancements that have the potential to further improve the performance of this important solid-liquid separation process. These enhancements, which include simple design modifications and new reagent packages, have been shown to significantly improve solids recovery and reduce product moisture in several experimental trials.

Jan 1, 2006

By W. D. Bullock

The King-Beaver mine of Asbestos Corporation Limited operates an open pit in the city of Thetford Mines, Quebec. The approximate loca-tion of the open pit is at Latitude 46° 02' North and Longitude 71° 20' West. The general topography is 1020 feet above sea level. Thirty-six percent of the company's scheduled asbestos ore production, for the Thetford Mines area, comes from the King-Beaver pit. The pit operates 24 hours a day, six days a week. Normal production is 10,500 tons of ore per day at a waste to ore ratio of 2 to 1. The remaining ore requirements are mined from the King-Beaver underground mine and the British-Canadian mine.

Jan 1, 1980

By James J. Gusek

Passive-treatment systems that mitigate acid-rock drainage (ARD) from coal mines have operating since the mid-1980s. Large systems at metal mines are being contemplated. A 95L/sec (1500-gpm) capacity system is planned this year at an underground lead mine in Missouri. Mine, process and environmental managers need to understand how and why passive-treatment systems work. They must understand what operational limitations to expect, as well as the economics of construction and operation compared to the alternatives, like lime precipitation. Wetlands have been recognized as nature's method of improving water quality. Contaminant reductions can occur through the precipitation of metal hydroxides, sulfides and carbonates and pH adjustments. Local conditions, oxidation state and water and soil chemistries dictate whether these natural reactions will occur under oxidizing (aerobic) or reducing (anaerobic) conditions.

Jan 1, 1995

A subsurface study of the Maria Lode and associated hydrothermal alteration of andesites within the Karangahake epithermal gold-silver deposit defined the local evolutionary sequence in the once active geothermal system.   Some implications for mining of epithermal deposits arise as a result.

Jan 1, 1984

By W. A. Burns

Vertical flow is an important mechanism in many petroleum reservoirs. Yet no adequate method has heretofore been proposed for determining the in-situ vertical permeability in a reasonable length of time. Core measurements of vertical permeability do not necessarily represent effective in-situ values. Cores may be representative of only localized pockets of high or low permeability, and total reliance on cores might cause one to overlook the presence of vertical fractures altogether. Conventional single-well tests, interference tests, and pulse tests commonly are used to determine horizontal transmissibility, khh/u, but generally are not designed to measure vertical trans-missibility or other groups containing vertical permeability, ku. A new well test described here provides a measure of in-situ vertical permeability as well as the previously measurable horizontal permeability. This "vertical test" determines the vertical diffusivity, kv/gcu, and horizontal transmissibility, khd1/u (where dl is the length of injection or production perforations). The test is basically a short-term interference or pulse test normally lasting less than a day. Conventional down-hole equipment is used between two isolated sets of perforations in the same well, as shown in Fig. 1. A "layer-cake" description of a reservoir can be obtained by running two or more vertical tests in the same well, each over different vertical intervals. Each test can be analyzed for the effective vertical and horizontal properties of the interval tested. In addition, a vertical well test can determine the effective- ness of a shale barrier or tight zone by testing across it. Field use to date of vertical testing has confirmed its utility in reservoir description. Mathematical Basis Interpretation of vertical tests for ku and kh is based on comparison of measured pressure response with computer-generated response. Pressure behavior during a vertical test in a homogeneous, anisotropic, infinite-acting reservoir (infinite in radial extent and bounded in both directions vertically) is given by the diffusion equation for slightly compressible fluids with negligible gravity effects.l A schematic diagram of the problem is presented in Fig. 2, and an analytic solution, based on the image

Jan 1, 1970

By W. N. Carr, J. R. Biard, B. S. Reed

An analysis of the semiconductor injection laser is presented which is based on a phenomenological model using device and material parameters. The intent of the laser threshold analysis is not to predict from theory the actual threshold current density but rather to provide a logical means of interpreting experimental results. The device and material parameters have been selected such that they describe both the threshold conditions and quantum efficiency of the lasev. A technique is proposed whereby the current required to obtain a population inversion is predicted from device 1-V characteristics. Experimental data are presented which support the analysis. THIS investigation is concerned with the characteristics of GaAs lasers fabricated in this laboratory. However, the assumptions used in these calculations should not limit their application to GaAs alone. It is felt that the analysis is sufficiently general to be useful in describing the operation of other semiconductor-laser materials. ANALYSIS heavily doped semiconductors to be considered. The absorption and/or generation of optical radiation may be completely specified in terms of q(E) and the probability functions f,,(E) and f,(E) which define the occupancy of the valence-band and conduction-band levels, respectively. The symbols used in this analysis are listed at the end. Following the approach of all' it can be shown that the effective gain coefficient, g, in the plane of a forward-biased P -N junction is g(E)=-ai@)[1-fv(E)-fc(E)] [1I In particular Eq. [I] holds for the photon energy at which lasing occurs, Ep. Throughout the following discussion Eq. [I] is considered only for the lasing transition E = Ep. For simplicity the functional energy dependence of the various factors is omitted in subsequent equations. Unless otherwise stated the symbols used represent the values at Ep. If the analysis is limited to the P-type side of the laser junction, the function q(l -f,,) is recognized as the band-to-band absorption in the P-type material at thermal equilibrium. Under forward-bias conditions the function f, is determined by the electron quasi Fermi level in P-type material. For sufficiently large forward bias the second term in Eq. [3] will become dominant and net gain will result; i.e., g will become positive. In order to simplify the subsequent analysis several assumptions are in order at this point. a) No conductivity modulation occurs. /„ is independent of f, and therefore go is a constant. b) The P-type material is heavily doped such that the degeneracy of the valence band permits popu-

Jan 1, 1964

By Susanne Hering, Brent Kirby, Charles D. Litton, Tracy Allen, Kirk R. Smith, Rufus Edwards

In developing countries, high levels of particle pollution from the use of coal and biomass fuels for household cooking and heating are a major cause of ill health and premature mortality. The cost and complexity of existing monitoring equipment, combined with the need to sample many locations, make routine quantification of household particle pollution levels difficult. Recent advances in technology, however, have enabled the development of a small, portable, data-logging particle monitor modified from commercial smoke alarm technology that can meet the needs of surveys in the developing world at reasonable cost. Laboratory comparisons of a prototype particle monitor developed at the University of California at Berkeley (UCB) with gravimetric filters, a tapered element oscillating microbalance, and a TSI DustTrak to quantify the UCB particle monitor response as a function of both concentration and particle size and to examine sensor response in relation to changes in temperature, relative humidity, and elevation are presented here. UCB particle monitors showed good linearity in response to different concentrations of laboratory-generated oleic acid aerosols with a coarse (mass median diameter, 2.1 µm) and fine (mass median diameter, 0.27-0.42 µm) size distributions (average r2 = 0.997 ± 0.005). The photoelectric and ionization chamber showed a wide range of responses based on particle size and, thus, require calibration with the aerosol of interest. The ionization chamber was five times more sensitive to fine rather than coarse particles, whereas the photoelectric chamber was five times more sensitive to coarse than fine. The ratio of the response between the two sensors has the potential for mass calibration of individual data points based on estimated parameters of the size distribution. The results demonstrate the significant potential of this monitor, which will facilitate the evaluation of interventions (improved fuels, stoves, and ventilation) on indoor air pollution levels and research on the impacts of indoor particle levels on health in developing countries.

By Douglas Brittsan

This paper presents pile tension and compression load test results for the Southern Freeway Viaduct (North) pile load test site. The testing program represents a collaboration between California Department of Transportation (Caltrans), Federal Highways Administration (FHWA), and a group of pile manufacturers and construction firms. The participating manufacturers included Fundex, Halliburton, Monotube, and Nicholson, with each firm supplying proprietary pile systems. The field test program measured and will allow the direct comparison of the tensile and compressive capacity of nine common and proprietary pile systems installed in nearly identical soil conditions. Data reported here-in details pile compression and tensile load-deformation measured at the pile head. Cursory data regarding pile installation details are included to aid in data interpretation.

Jan 1, 1993

By Theresa M. Bodus

The strength of roof shales is, in part, a function of the preferred orientation of clay minerals within them. Therefore, analysis of clay fabric under both air-dried and hydrated conditions should be helpful in understanding roof shale failure. Core samples were collected from the Energy, Anna, and Lawson shales, which are locally present as roof shales of the Herrin No. 6 coal of southern Illinois. The Clay Fabric Index (CFI) was measured for thirty core samples, using X-ray diffractomtry, to investigate the relationship between clay fabric and roof collapse in coal mines. Greater CFI values indicate a weaker preferred orientation among clay minerals, which generally results in a weaker inter-grain bond. Average CFI values for air-dried samples were: 0.15 for Anna shale; 0.20 for Energy shale; and 0.37 for Lawson shale, .After the introduction of water, average CFI values increased to: 0.28 for Anna shale; 0.22 for Energy shale; and 0.43 for Lawson shale. The laboratory results indicate the following: [l] under air-dried conditions, Anna shale is the most stable, followed by Energy and Lawson shales; and 121 under hydrous (mine) conditions, Energy shale is the most stable, followed by Anna and Lawson shales. In mine environments where roof failures involving Energy shale have occurred, planar trends delineated by a relatively high density of small (0.2-4 cm diameter) iron concretions have been reported along the failure surface. Radial cracks have been observed around unsealed anchor bolt holes in the Anna shale. Instability of the Lawson shale is ubiquitous in coal mines. In the laboratory, similar physical changes were noted in the shale samples after the introduction of water, including [l] increased hydration around the perimeter of iron concretions in Energy shale, [2] radial extension cracks in Anna shale, and 131 extreme slaking of Lawson shale. Measured increases in the CFI reflect the observed physical changes of the samples upon the introduction of water, which probably reflect changes in strength that may result in roof failures in hydrated mine environments.

Jan 1, 1989

Currently raw brown coal is fired in the Latrotx; 'ahcc th,iki~, Lanying with it two major penalties, (a) boiler efficiency of 65 - 70 per cent (in terms of GCV), (b) much higher boiler cost than for black coal. Drying the coal, in energy-efficient, and cost-efficient manner, opens the way to efficiencies of order 88 per cent and enables the lower cost black coal type boilers to be used. With the higher boiler efficiency goes much higher combustion temperatures and the effect of this on radiative heat transfer is a major factor in reducing boiler cost. In a fluidised-bed combustor the temperature is controlled to 800C - 900C. In a pulverised fuel combustor higher temperatures are however achieved and can increase boiler fouling due to the salt content of the coal. This is a problem which needs to be solved. Victoria has the prospect of lifting efficiency from 28/29 per cent to 35 per cent, of reducing carbon dioxide output correspondingly and reducing cost of power stations. So far as gasification is concerned, efficient removal of liquid water from the coal is important to the overall efficiency.

Jan 1, 1992

By D Lautier, A A. Ndiaye, A Galli

Traditionally gold producers had built up hedge books to protect themselves against adverse changes in the commodity price, but diversified mining groups were staunchly opposed to hedging in any shape or form. The situation has evolved over the past few years. Gold miners have been reducing the size of their hedge books in line with the rising gold price. Commentators have talked about ædouble-digit dehedgingÆ and have suggested that this is the final countdown for gold hedge books. It sounded as if the era of hedging by mining companies was drawing to a close. But as appearances can sometimes be misleading, we decided to find out what mining companies were actually doing. Companies listed on stock exchanges are now obliged to give details of their derivatives holdings in their annual reports. Two or three years ago there was no such obligation. Our reality check was based on the latest annual report issued by three multinational mining groups; two with diametrically opposed views on hedging (Rio Tinto and Barrick) and the third (BHP Billiton) with an intermediate position. This snapshot of their derivative positions at a point in time revealed that Barrick and BHP Billiton have substantial derivatives positions (worth billions of dollars) to protect against adverse changes in foreign exchange rates and interest rates. Moreover Barrick has recently started hedging against increases in fuel prices. Despite its opposition to hedging, Rio Tinto has derivative positions worth several hundred million dollars, but these are primarily a legacy from various mergers and acquisitions over recent years or were entered into as a condition of project financing. Lastly we were surprised to discover that Barrick was holding asset-backed commercial paper (ABCP). So the idea that mining companies donÆt hedge their risks is just another urban myth.

Jan 1, 2009

By K T. Broekman, R L. Koenig

"The Braemar Iron Formation is atypical ore when compared to the current magnetite ores being processed. In attempting to process and economically recover the vast quantities of iron ore stored within the Braemar Iron Formation, æshifting the paradigmÆ is required. The formation has a low Davis tube recovery (DTR) grade of 15 - 20 per cent, which is much lower than magnetite ores processed in Australia. Despite this, by thoroughly testing and understanding the ore characteristics, it is found that the Braemar ores have significant advantages to processing than the harder banded iron formation (BIF) and taconite resources.The Hawsons magnetite iron ore resource has been known from the early 1960s when CRA explored the area. The grade was low and the Pilbara region discovery lead to the development of high-grade direct shipping hematite ores. Carpentaria Exploration (CAP) rediscovered the magnetite whilst undertaking multi-commodity exploration in the Broken Hill district during 2009. Shifting the paradigm away from grade the advantages of processing this ore are achieved by having an extremely low waste to ore ratio, lower Bond work index, lower abrasion levels and high-grade magnetite concentrates with little impurities other than silica. While developing the Hawsons Iron Project (HIP) it became more apparent that a positive business case is achievable when the following factors are exploited: very large resource - the resource is contained within one pit the rock fractures easily along grain boundaries - ideal for cheap impact crushing of the ore the ore is extremely soft, with a Bond work index of 6.3 - 8.0 kWh/t all major infrastructure required is readily available - rail, power, access and port the mine is in close proximity to Broken Hill - rich mining history and skill set available the resource contains many billions of tonnes of magnetite mineralisation.Shifting the paradigm by selecting equipment suitable for processing soft ores and not hard BIF or taconite ores and taking locality and available infrastructure into account may change the way people approach new low-grade resources in future.CITATION:Koenig, R L and Broekman, K T, 2013. Understanding ore characteristics and equipment selection, in Proceedings Iron Ore 2013, pp 403-410 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013