Search Documents

By Tim O’Neil

Caterpillar has introduced its 5090B front shovel, to work with 40 to 70 st (36 to 63 t) trucks. The new unit replaces Cat’s 5080 hydraulic excavator. The 5090B offers more engine horsepower, higher flow, greater digging forces, higher swing torque, faster swing speed and more drawbar pull than its predecessor. It can also handle larger bucket sizes than the previous model. These improvements enhance productivity and make the 5090B a high-volume material handler for hard rock and aggregates producers.

Jan 1, 2003

By Gerald G. Griswold, Allan G. Provost

INTRODUCTION The Norad Expansion Project was located 10 miles southwest of Colorado Springs, Colorado, within Cheyenne Mountain. The expansion areas to be excavated would be adjacent to the existing underground Norad complex, which would remain in operation during the work on the expansion. The original complex had been constructed approximately eight years earlier and had been in full operation for approximately five years. Phase I, Excavation was awarded the Tiro Construction Corporation, a subsidiary of Harrison Western Corporation, Denver, Colorado, in the fall of 1970. Notice to Proceed was given to Tiro on 28 December 1970. The project owner was the U. S. Air Force, design was performed by the U. S. Corps of Engineers, Omaha District, who would also serve as the construction agency. [ ]

Jan 1, 1979

By Kenneth H. Johnston

This report describes an in situ combustion project and three waterflood projects in Allen, Anderson, and Wilson Counties, Kansas, that will be visited during the 1964 annual tour of the Kansas-Oklahoma Waterflood Association. Among the unique features of the projects are the movement of heavy crude oil through the reservoir and into the wellbore with energy furnished by burning s portion of the crude oil therein. Another feature is the simultaneous injection of C02 and water, through separate tubing into input wells during early development, to increase injectivity at moderate pressures, Discussion of individual projects includes information on their early history, source and treatment of injection fluids, oil production-decline curves, and the results of water injection on oil production.

Jan 1, 1964

By K. P. Black, G. W. Sevick, D. E. Hockley, K. S. Sexsmith, J. T. Chapman

Mineralogical analyses of carbonates in depyritized tailings and pyrite concentrate (from depyritization of the tailings) were completed as part of the tailings characterization for the Crandon Project, a massive sulfide deposit in northeastern Wisconsin. The mineralogical study was designed to determine the proportion of calcium and magnesium carbonates, and therefore the effective buffering capacity of carbonates in the tailings. The depyritized tailings are net acid consuming and will be stored in a surface tailings management area. The pyrite concentrate is net acid generating and will be used as backfill in the underground mine workings. The majority of carbonates in the depyritized tailings were ferroan dolomite containing 10 to 15% iron (by weight) and lesser amounts of siderite and magnesian siderite. The proportion of calcium and magnesium-rich carbonates corresponds to several independent tests of carbonate neutralization potential (CO3-NP) availability. The pyrite concentrate had less CO3-NP, indicating segregation of the carbonates during pyrite flotation. These carbonates reported higher iron contents, consistent with the relatively lower availability of CO3-NP in the pyrite concentrate.

Jan 1, 2002

By David L. Shearer

INTRODUCTON James Howden first secured an order for two Service Tunnel Boring machines in November 1986. These Tunnel Boring machines were 5.7 and 5.4 metres in diameter and the full length including back up was 215 metres. Manufacture commenced in December 1986 at the Glasgow factories of James Howden & Company with the deliveries to site of the machines in September 1987 and March 1988 respectively. In December 1987 two further orders were secured for the land running tunnels at 8.7 metres diameter. This paper presents some of the challenges in building tunnel boring machines for the Eurotunnel project between Britain and France. The general specifications of the Tunnel Boring machines and length of drives are shown in Appendix 1. DESIGN PARAMETERS The specification given by the Consortium TML on behalf of their client Eurotunnel cleary indicated that cutting of the face should be concurrent with the building of the precast concrete lining rings. In order to do this a telescopic machine was thought to be the best solution. Ground conditions were described as chalk marls of homogeneous nature with the possibility of friable areas and some revelling. A shielded type TBM with open cutter head was chosen together with a telescopic section and a rear

Jan 1, 1989

By Stuart McTavish

"Noranda's Goldstream mine is a 1,500 ton per day copper-zinc mine located 60 miles north of Revelstoke, B.C.The orebody which contains 3.69% Cu and 2.69% Zn was discovered in 1972. Construction of the mine and mill was completed in 1982 and start up was achieved in May 1983.This paper will describe the flowsheet and related equipment 1n the crusher and mill, in particular the dewatering section where two Larox pressure filters are used to dry the concentrates.INTRODUCTIONThe Goldstrean property is located 60 miles north of Revelstoke, B.C. in the Goldstream River Valley (Figure #1). It was discovered during the construction of a logging road in 1972. Exploratory drilling was initiated in 1975, and in 1976 a portal was collared to obtain underground data. Samples were taken from the underground workings for metallurgical bench tests and a pilot plant run.Due to economic conditions, the decision to go into production was delayed until 1980. Concentrator construction and underground development progressed simultaneously during 1981 and 1982, and were completed by the end of 1982. Start up of the concentrator was achieved on May 2, 1983.The ore typically contains about 40% sulphides, which are chalcopyrite 10%, sphaletite 6%, pyrrhotite 20%, and pyrite less than 5%. The sulphide minerals have a high degree of intergrowth. Most of the sphalerite occurs in micron sized grains which are embedded in the pyrrhotite and, to a lesser degree in the chalcopyrite. There is also some fine dissemination of the chalcopyrite in the pyrrhotite. The waste rock is made up of about 30% quartz, 20% guange silicates, and 10% carbonates. The ore has a specific gravity of 3.2 and a natural pH of 8.2."

Jan 1, 1985

The literature pertaining to the electrochemical reaction at the anode during electrolytic reduction of alumina by the Hall-Heroult process is not in universal llgreement about the gaseous product. The possibility of electrochemical formation of CO at the anode was examined using existing data. Although the thermochemistry favours co-evolution of CO and CO2 with CO as the major product, the mechanism of the reaction shows this is unlikely. Since the origin of CO can be more logically explained by non-electrochemical mechanisims, it is concluded that CO2 is the only product from the electrolytic reaction at all current densities.

Jan 1, 1967

By Leo J. Vogel, E. D. Hummer, David J. Akers

INTRODUCTION An efficient refuse-disposal system is a necessary part of the modem cleaning plant. The large-scale refuse system and disposal area, engineered for the lifetime of the plant, has become more important due to the greater tonnages of refuse produced from increased quantities of mechanically mined and prepared coal. Laws and increased government regulations have affected the design and operation of disposal systems. THE EFFECT OF MINE AND PLANT OPERATION Refuse disposal starts at the mining face. The mining system, the type of roof support, the machinery used, and the degree of discipline at the face contribute to the amount and type of refuse that must be removed through the disposal system. Economies gained through modification of the mining system or mining machinery may be partially offset by increased dilution of the mined coal with impurities from associated rock formations. In some cases the change in the mining system and equipment has reduced the dilution. In all cases the ratio of impurities that must be removed from the raw-coal feed to the plant not only affects the maintenance and

Jan 1, 1979

By Luis Valdivia

Dado que el objetivo principal de un departamento de Geología de exploraciones es el de estimar recursos minerales en nuevos blancos de exploración identificados a través del análisis e interpretación de información geológica proveniente de diversas fuentes. En ese sentido, el presente texto señala la sistematización de los datos geológicos como el uso de las imágenes satelitales, fotografías aéreas, geofísica, geoquímica, cartografiado geológico, sondajes diamantinos, catastro minero, datos geográficos y políticos, etc. a través de un servidor que integre dichas estructuras lógicas de conocimiento, de manera que todos puedan acceder a ella de manera fácil y dinámica. Asimismo, para los datos de carácter numérico llámense muestras, sondajes, leyes, se utiliza la plataforma Access como gestor de base de datos, mientras que para la información grafica superficial, el software ArcGis.

Sep 24, 2008

By Rob Boom, Yasuyuki Tozaki, Greg Traquair

The objectives of the business case are to examine a proposed metallurgical project and answer fundamental questions about project feasibility, risks, opportunities, and value. A business case fulfills these basic functions: estimates economic value; helps to understand competitiveness; serves as a risk management tool; and serves as a communication tool. A business case evolves with the project life cycle, and supports the gate reviews at the end of each phase of engineering, through to project construction and operations. A business case must be holistic, including all elements of scope that can impinge on project risk and value.

Jan 1, 2015

(Published by courtesy of the Great Boulder Pty. Gold Mines, Limited)1. INTRODUCTIONThe faults described in the following paper are of a somewhat unusual character, and have presented a serious problem both in the development and mining of many ore-bodies on the Eastern side of the Boulder Belt. They are mentioned only briefly in the literature of the field, but were observed by, both Stillwell (1)t and Gustafson (2), and have been studied by other geologists and operators in various parts of the "Belt." Their effect on the lodes of Hamilton Section, Great Boulder Mine, was described by King (3) in 1937, and, during recent years, they have been encountered in most of the Great Boulder workings extending east of the Boulder Dyke.Although this paper is based mainly on a study of faulting and development problems on the Great Boulder mine, the general conclusions reached may be applicable to the solution of similar faulting problems in other mines throughout the field.In order to arrive at a clear understanding of the somewhat complicated relationships which the east-dipping faults bear to the lode systems it will be necessary to give a brief outline of the salient geological and structural features of the "Belt" before proceeding to describe the faults themselves.2. GENERAL GEOLOGYThe most recent descriptions of the geology of Kalgoorlie are those by Stillwell (1) and Gustafson (2) and the reader is referred to these as representing the basis of current knowledge of the geology of the field.The Boulder Belt is comprised of a central core of altered quartz dolerite which is flanked on either side by fine grained greenstones and lavas, usually referred to as the calc schists. Down the centre of the quartz dolerite mass there is an infolded bed of slate (2, p. 105) which has been intruded in lit par lit fashion by albite porphyry; the composite body of slate and porphyry so formed is known as the "Boulder Dyke." Numerous smaller porphyry dykes intrude both the quartz dolerite and the calc schist; these vary in composition and range from chloritised hornblende porphyrites to albite porphyries.The whole of the rock assemblage has been subjected tG a considerable amount of folding, faulting, shearing and fracturing, the greater part of which took place before the formation of the lodes.

Jan 1, 1941

By D. Govender

In recent years, economies of scale have continued to drive copper projects to larger throughputs to offset depleting lower grade resources. A decade ago there were only a small number of projects that stretched beyond 100,000 Mtpd throughput rates. Nowadays and moving forward virtually all the major copper projects are sized beyond this, with throughput rates up to 250,000 Mtpd now under evaluation for a number of key projects in Chile and Peru. This paper explores the development from the 160 m3 flotation cells, through to the 257 m3 cells and nowadays to the 660 m3 machines. The contributions of specific copper concentrators to this growth phase are reviewed herein. The historical basis of flotation machine scale-up is also briefly discussed. Metallurgical results as well as layout, maintenance and operational aspects are highlighted.

Feb 27, 2013

THE Yallourn chimney has aroused interest, as it is, for the time being, the tallest structural erection in Australia. Its height was not decided on, however, with the object of breaking records, but is purely incidental to the purpose which it serves. Theboiler plant at the briquetting works (first instalment) consists of five Babcock and Wilcox land-type water-tube boilers, each of 4510 sq ft. heating su:r£ace and 225 sq. ft. grate area in the form of step grates. Four boilers will normally produce 73,000 lb. of steam per hour at a gauge pressure of 265 lb. and a temperature of 6500 F., the fifth boiler being a reserve. Each boiler will consume about 100 tons of Yallourn coal per 24 hours. Provision is made for future installation of economizers, should it be found desirable. Designing for this condition, and allowing for a waste gas temperature of 3500 F. and an air temperature exceeding 1000 it was found necessary to have a draft of about 1.3 in. (water gauge) at the base of the chimney, and to deal with about 2000 cub. ft. of gases per second. Estimates were made of the cost of providing the necessary draught by means of fans and by means of a tall chill).ney. The annual charges of the two methods differed only slightly, and the tall chimney wasselected as being the more general practice in briquetting factories.Estimates were prepared for brick and concrete chiIlllleys. Yallourn bricks at that time were hand-made, and, while very suitable for domestic work, were not capable of withstanding high compressive stresses. The chimney design to suit these bricks thus required to be on very ample lines, resulting in high cost. Machine-made bricks from Melbourne would cost about £5 10s. per thousand on the site, with extra for radials, so that high cost again resulted. On the score...

Jan 1, 1924

By A. A. Stripling

The Cretaceous limestone wells of the Mara/Maru-caibo Dist. of Venezuela are extremely prolific producers. To maintain production on cessation of natural flow, large scale gas-lift operations were commenced involving high production rates on caring Flow. For the design of these gas-lift installations it was essential to have some knowledge of the pressure gradients involved in casing flow, so that the required injection pressures, optimum gas injection raws, etc., could be forecast. This paper presents a method of calculating these annular pressure gradients. Basically the method makes use of an energy balance equation coupled with an empirical energy loss factor derived from field data. The calculations have been put in a form suitable for "punch card-type" calculating machines. A set of gradient curves for Mara/Maracaibo conditions covering flow rates up to 12,000 B/D, and GOR's of 500 to 2,000 cu fd/bbl is presented. From these curves the flowing BHP can be predicted from surface data and the vertical pow performance under varying conditions of gas injection can be estimated. The method has been applied to La Paz and Mam gas-lift operations for over three years and has given consistently accurate results. INTRODUCTION The Cretaceous limestone fields of the Mara/Maracaibo area in Venezuela are characterized by the presence of widely distributed fissure systems. Under these conditions individual wells frequently have extremely high potentials and such wells are generally flowed on the casing-tubing annulus in order to reduce the pressure loss in vertical flow. To maintain production on cessation of natural flow, an extensive gas-lift system was planned. As a first approach to this gas-lift design problem, an attempt was made to construct a set of empirical flowing gradient curves from the available subsurface pressure data. Such a method has been used successfully for tubing-flow conditions in California by Gilbert'. Unfortunately, the empirical construction of casing-flow gradient curves presents additional difficulties, as pres- sure bombs cannot bc run in the casing-tubing annulus against high rates of flow. Thus, the Full flowing gradients cannot be defined by actual measurement and the best that can be done is to obtain spot pressures at the tubing shoe. Under these conditions a vast accumulation of BHP data is required to construct a set of gradients. To the La Paz and Mara fields the majority of the available flowing pressure measurements fall into a relatively narrow GOR range, in the neighborhood of the solution ratio. While there appeared to be reasonable prospects of constructing gradient curves for this limited range, measurements at higher GOR's, which were of major interest for gas-lift operations, were relatively few and the prospects of constructing empirical curves cor~spondingly remote. As an alternative approach, the possibilities of a mathematical analysis of vertical flow conditions were investigated. May and Laird2fV n 1934 presented an excellent analysis of the vertical-flow conditions in the Anglo-Iranian Oil Co.'s fields. Their analysis was based on an energy-balance equation and calculated the losses due to kinetic energy, friction and slippage separately. By combining these losses with the total calculated available energy, the required depth-pressure traverse could be deduced. On applying the method to La Paz conditions, good results were obtained for tubing flow at high tubing-head pressures. However, for lower wellhead pressures (300 psi and under) the discrepancy between calculated and measured values increased appreciably. It was considered that this was probably due to energy losses caused by slippage or liquid hang-up in a continuous gas phase, for which it was difficult to visualize any analytical approach. In 1952 Poettmann and Carpenter4 presented a method of pressure gradient calculation which, while based on an energy-balance equation similar to that employed by May and Laird, made no attempt to evaluate the various components making up the total energy loss resulting from irreversibilities of flowing fluids. Instead, they proposed a method of analysis which assumed that all significant losses for multiphase flow could be correlated in a form similar to that of the Fanning equation for frictional losses in single-phase flow. They then derived an empirical relationship linking measurable field data with a factor which, when applied to the standard form of the Fanning equation, would enable the energy losses to be determined. The total available

Soon after the Rosebery concentrator commenced operations in 1936, an investigation was begun in an attempt to discover a substitute for cyanide in lead flotation. Cyanide is an excellent depressant for zinc and iron, but it also powerfully depresses the copper, silver and gold bearing minerals present in Rosebery ore, thus allowing them to pass through to the zinc concentrate or final residue where they are of little or no value.The investigation was not entirely successful, but it did indicate that sodium bisulphite or sodium sulphite could be used as a depressant for zinc without depressing the copper, silver and gold bearing minerals. The sulphites were, however, much inferior to cyanide as apyrite depressant.At about this time, I. W. Wark, using the captive bubble technique, had shown that, at the concentrations normally used, sodium aerofloat is not a promoter for pyrite or galena in alkaline solutions (see his book "Principles of Flotation", p. 188). Some preliminary tests on the production of a copper concentrate from Rosebery ore were therefore carried out using sodium sulphite as depressant and sodium aerofloat as promoter.The results of this work were promising but, since Rosebery ore usually carries only about 0·5% copper, there did not seem to be much incentive to carry the work further. With the outbreak of war, however, Australia became desperately short of copper and the relatively small amount in the ore. became of sufficient importance to...

Jan 1, 1952

By A. A. Debrah

Artisanal and small-scale mining (ASM) plays a fundamental role in the national and local economies of resource-rich countries in Africa. As such, more effort must be geared towards fostering this type of economic activity to sustain livelihoods in rural communities. Across Africa, efforts to operationalize ASM based on a sustainable development framework have been quite tedious and often ineffective. This is because most of these frameworks lacked context and an understanding of the continuum from the artisanal through small-scale and up to the junior miner, grouped under the general term ?ASM?. Driven by the need to contextualize some of the definitional issues in this niche sector, and gain a clearer understanding of their peculiar challenges, this paper aims to contribute to the debate on ASM by considering two of Africa?s resource-rich countries ? Ghana and South Africa. Since South Africa has made greater inroads in protecting the interests of small-scale miners, we thus draw comparisons from both countries? approach to ASM, outline the lessons learnt, and provide recommendations regarding the ways forward.

Jan 1, 2014

By N. A. Eilertsen

Procedures of mining high-calcium limestone underground at the Kimballton mine of the Standard Lime and Cement Co. in Giles County, west-central Virginia, are described. Drilling and blasting procedures arc discussed in detail, and direct mining costs are tabulated in percentage of total cost. Output, about 1,725 tons of limestone a day, is attained with heavy trackless equipment by the room and pillar method of ruining; modified by benching floors. Operating features include underground air compression, electric-eye control of curtained doorways, use of a single jumbo drill rig for all drilling, and an effective plan for maintenance of equipment. The company's safety program has contributed to an outstanding safe mining record. The mina is integrated with a plant on the property which converts the stone to metallurgical and chemical grade lime.

Jan 1, 1964

By Joël Kapusta

La pyrométallurgie du cuivre est essentiellement une chaîne de trois étapes successives d’oxydation préférentielle du fer et du soufre et des impuretés moins nobles que le cuivre qui sont contenues dans le concentré de cuivre issu de l’usine de concentration du minerai, aussi appelée concentrateur. La Figure 1 illustre la chaîne complète d’élaboration du cuivre depuis la mine jusqu’au cuivre pur. La voie hydrométallurgique traite le concentré par lixiviation, c.à.d. par dissolution en phase aqueuse à température typiquement inférieure à 100 ou 150⁰C, alors que la voie pyrométallurgique traite le concentré par fusion à température de l’ordre de 1200 à 1300⁰C.

May 2, 2024

By R Schiller, E Chait

"Quebrada Blanca is a porphyry copper deposit located in the Eocene-Oligocene belt of Chilean Andes. Operation started in 1994 and original reserves for supergene mineralisation gave a life-of-mine (LOM) of 20 years; however, further exploration extended the LOM until 2020.In order to optimise the remaining five years of supergene resource, geometallurgical variables were added to the geological model including copper recovery and acid consumption. LOM plan encompasses finishing the phase number eight and the future development of phases 11 and 13.LOM lithologies include diorites, quartz monzonites, porphyries, igneous and tourmaline breccias. Main alterations are: potassic, phyllic and argillic. Litho-alterations or geometallurgical units were formed by combining five types of rocks with three types of alteration. According to statistical information, the deposit can be represented with 12 litho-alteration units, which cover 98 per cent of the LOM volume.For copper recovery information, there were 40 mini-columns tests made in order to obtain kinetics curves and copper recovery values after comparing the difference between head and tails grades. Acid consumption was obtained using an automatic neutraliser device-based test.Historical data said that copper recovery in pads after 450 days of irrigation is around 75 per cent of recoverable copper while acid consumption is around 5.5 kg/t.According to this study, lower recoveries are related with potassic-altered diorites and argillic-altered quartz monzonites with values around 60 per cent. On the other hand, best recoveries could be found in potassic-altered quartz monzonites and argillic-altered diorites with values closer to 80 per cent.It was also revealed that the most reactive rock is the potassic-altered diorite with 12 kg/t of acid consumption. This rock covers approximately 40 per cent from phases 11 and 13.The final geomet model was calculated using a program that relates each geometallurgical unit with a specific copper recovery and acid consumption value. Results found after comparing model-obtained information with historical leached pads data were used to validate the model.CITATION:Chait, E and Schiller, R, 2016. Adding Copper Recovery and Acid Consumption Variables to the Geological Model of Quebrada Blanca, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 257–266 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By M. D. Lackey

The "Art" of Big Hole Drilling has been in a continual state of evolution at the Nevada Test Site since the start of underground testing in 1961. Emplacement holes for nuclear devices are still being drilled by the rotary drilling process, but almost all the hardware and systems have undergone many changes during the intervening years. The current design of bits, cutters, and other big hole drilling hardware results from contributions of manufacturers and Test Site personnel. The dual string, air lift, reverse circulation system was developed at the Test Site. Necessity was really the Mother of this invention, but this circulation system is worthy of consideration under almost any condition. Drill rigs for Big Hole drilling are usually adaptations of large Oil Well drill rigs with minor modifications required to handle the big bits and drilling assemblies. Steel remains the favorite shaft lining material, but a lot of thought is being given to concrete linings, especially precast concrete.

Jan 1, 1983