Search Documents

By Carlos Berlini Filho

As inclusões exercem um papel fundamental na lingotabilidade dos aços produzidos em lingotamento contínuo. É conhecido na literatura o efeito da composição das inclusões na formação de obstruções em válvulas submersas. Contudo, um problema também recorrente no ambiente industrial é o desgaste dos tampões e válvulas submersas do distribuidor, que impede o controle de fluxo de aço para os moldes. O presente trabalho visa avaliar a influência da composição das inclusões na taxa de desgaste de tampão. Foram avaliadas inclusões de aços acalmados ao Si-Mn em corridas que apresentaram diferentes valores de desgaste de tampão. A partir dos resultados obtidos foi possível concluir que a taxa de desgaste de tampão é consideravelmente dependente do teor de MnO das inclusões e que um maior teor de Al2O3 pode contribuir também para reduzir o desgaste.

Aug 17, 2017

The treatment of mixed lead carbonate and lead sulphide concentrates at Mount Isa presents a problem which is unique ,in the lead smelting world; a problem whose solution is far from simple, and is not yet complete. Two years of study under plant conditions have definitely proved, however, that a most satisfactory sinter can be made in a single-pass roast.The object of this paper is to present a brief record of the development of the single-pass roast and a resume of current practice in the smelting plant. The sintering operation is discussed in greater detail, as it is upon this phase of the work that every item in the smelter operating programme depends.The smelter, to-day, presents a very much simplified layout, equipped for economical, straightforward operation, requiring, however, very careful and constant supervision, due to the extreme delicacy of the sintering operation and to the rapid and wide variati9n in the nature of the concentrates which are to be handled.

Jan 1, 1933

By C. F. Jackson

THE work of, the Mining Methods Committee is now well under way. Following discussions previous to and during the February meeting, an Outline for Papers on Mining Methods was prepared, and over a thousand copies have now been distributed to committee men, to section secretaries and to members who have indicated any interest in the subject. The objective of the committee is to prepare a symposium on mining methods which will be of real practical value to the operator and engineer in the solution of every-day mining problems. It is planned to cover the entire field of mining in such a way that the different branches of mining, such as coal and ore (iron, copper, lead, zinc and precious metal) can benefit from the experience of the others at points where they have problems in common.. It is realized fully that each of these branches of mining possesses its own peculiar problems, but at the same time, there are prob-lems in connection with each, where the experience in others should be of value. The committee proposes to proceed along the following lines: 1. To present a general classification of mining methods, showing their inter-relationship, and at the same time .provide a common language for the discussion of mining methods and a nomenclature that will have the same meaning wherever used. A com-plete set of illustrations will accompany the classi-fication to make clear the terminology adopted and to show graphically the inter-relationship of methods. 2. To show the relationship between the physical characteristic of the deposit, the economic consider-ations and the. mining method., It is not proposed to treat this subject as a mere academic problem, but to secure reports from every mining company of impor-tance in this country, which will show what methods or modifications and combinations of methods have actually been applied and the physical conditions and economic considerations which have led to the adoption of these methods in each case. The Mining Methods Committee has drawn up an Outline for Papers on Mining Methods to be distributed among mining engineers and operators, giving in detail the information desired. This outline is the result of several months of careful thought and is a composite of the suggestions of many engineers and mining company officials from all parts of the United States.

Jan 7, 1922

By J. Klemenic

This paper presents an analysis of gold production and prices over an extended period. Production patterns are provided for the world as a whole and for the five major producing countries. Gold prices as a function of interest rates, as measured by municipal bond rates, are given for the period 1947 to the present. World gold production has had a phenomenal increase since 1980, with the exception of South Africa, all major producing nations participated in this increase, even though the price of gold generally has been decreasing since the high level attained in 1980.

Jan 1, 1993

By L. Bomvisinho

As a result of today?s requirements for larger mills with higher power demand, and in order to cope with maximizing throughput, and optimize grinding efficiency, the minerals industry is increasingly relying on the robust Gearless Mill Drive (GMD) solution. This paper describes the new features introduced with the revolutionary ABB drive controller for Gearless Mills, and explains the benefits this can bring to the operation. Extensive surveys have been performed with GMD users to gather suggestions and understand the market wishes. As a result the new driver controller capabilities and functionalities focus on safety, high availability, operational flexibility and remote diagnostics.

Jan 1, 2010

By C. Ortuglio

The effect of cracking by increasing the free space above the charge on the composition and yields of the volatile products from carbonization of Pittsburgh-bed coal and one industrially used blend from Eastern United States and one from Western United States was investigated with the BM-AGA carbonization apparatus. Increasing the free space above the charge from 1 inch to 3 inches, to 6 inches, and to 9 inches resulted in lower tar yields and increased gas and light oil yields. Anthracene and naphthalene yields were increased; quinoline and benzene insoluble fractions of both the tar and pitch increased considerably with increased free space, although the carbon content of the tars and pitches increased only slightly. Increased cracking, occasioned by the increase in free space, resulted in a decrease in the yields of tar acids, tar bases, neutral oils, olefins, aromatics, and paraffins and naphthenes. Gas composition was relatively constant; hydrogen and methane tended to increase and ethane decrease. Results of the investigation are being used to design a unit to upgrade the volatile products of carbonization by cracking the hot products as they leave the carbonization chamber.

Jan 1, 1970

From time to time failures occur in structures made of lead, and the failure may be due to corrosion involving a definite thinning of the lead sheet, or it may be of such a nature that cracks develop and the lead appears to disintegrate. The idea of lead cracking will at once suggest something abnormal, for common experience shows that this metal is very ductile and will withstand considerable bending without showing any sign of fracture. Cracking, on the other hand, is usually associated with brittleness.Fig. 1 is a natural-size photograph of a cracked sheet of lead. Prior to photographing, the sheet was etched byimmersion in a solution of ammonium molybdate. Several characteristics of this crack will be evident. First of all it is distinctly a zigzag crack, and secondly it passes between, rather than through, certain well-defined areas which appear bright in the photograph. This is particularly noticeable at the lower end where the crack appears to terminate.

Jan 1, 1932

By W. Schubert, N. Radoncic

"The term “squeezing” is frequently used, although it is ill defined. Definitions like “large and long lasting displacements” raise the questions about the threshold values for the magnitude and duration of displacements. Large displacements during tunnelling frequently are observed in fault zones with high overburden. Whether this causes problems very much depends on the design approach used. On the one hand, the magnitude of expected displacements has to be predicted prior to excavation to provide for enough allowance for the displacements without violating the clearance profile. On the other hand, the support characteristics must be compatible with the expected imposed strains. As the magnitude of the displacements and thus the strains in the support depend on the support capacity and its characteristic (yielding potential), only well engineered systems will be successful.Experience in Alpine tunnels over the last decades has shown that closed shotcrete linings can sustain a strain of approximately 0.8% to 1% without failure. Any strain above this value inevitably leads to failure of the lining, and thus a loss of resistance, causing additional displacements. Based on a large number of simulations, a criterion for a critical overburden depth up to which closed linings can be used has been developed. Traditionally open gaps in the shotcrete linings have been used to allow for larger strains. To enhance the efficiency of the linings, yielding elements have been developed, which are integrated in the shotcrete lining, allowing large strains and controlled development of support resistance (Figure 2). When designing such yielding support systems, the development of the displacements, as well as the rheological behaviour of the supports must be considered. As the development of displacements to a large extent depends on the face advance, also the advance rate has to be considered, to be able to compare the time-dependent strength of the lining to the stresses developing as a result of the imposed strains. Another issue is the compatibility of the rock bolts with the large strains. With standard grouted bolts, there is a potential that the “fresh” grout is sheared due to the initially large strain rates. Special rib designs of the bolts allow for a higher strain tolerance.For successful tunnelling through fault zones quality monitoring and up-to-date data evaluation is of crucial importance. With advanced evaluation tools, changes in the ground conditions ahead of the face can be reliably predicted. With the help of empirical relations, the development of the displacements for different advance rates and supports can be predicted, allowing for the determination of the required overexcavation.The paper presents a review of the development of ductile elements, methods of analysis, and monitoring data interpretation."

Jan 1, 2015

By A. C. Johnson, es Hol, E. O. Binyon

"INTRODUCTION AND SUMMARYThe tungsten properties of Lincoln Mines, Inc., and North Tem Flute Mining and Development Co. were first explored by the Bureau of Mines in 1942. Work on the project comprised trenching, sampling, a small amount of road and trail construction, and a small amount of core drilling. From April 13 to December 10, 1944, additional diamond drilling was done by the Bureau of Mines to test the lateral and downward extensions of the various tactite zones along the contact south of the Lincoln mine, including the property of the North Tem Piute Mining & Development Co.Claims leased by the Lincoln Mines, Inc., are in secs. 25 and 36, T. 3 S., R. 56 E.; secs. 30 and 31, T. 3 S., R. 57 E.: and sec. 1, T. 4 S., R 56 E., M. D. B. & M., in the Tem Piute Mining District, near the north end of the Timpahute Range in west central Lincoln County, Nev. D. B. Fegles is president of Lincoln Mines, Inc. and general offices are in the Wesley Temple Building, Minneapolis, Minn.In June 1945, the Atolia Mining Co. leased the property and purchased the mill and mining equipment from Lincoln Mines, Inc. P. R. Bradley is president of the Atolia Mining Co., whose offices are in the Crocker Building, San Francisco, Calif. This company surrendered the lease on the property on September 30, 1948. The property owners are continuing operations and are now engaged in building a 20-ton mill.The claims of the North Tern Flute Mining & Development Cc. are in sec. 1, T. 4 S., R. 56 E., M. D. B. & M. Merle F. Schofield is president of the company and maintains an office at Hike, Nev. These claims were leased by H. P. Laslett, of the Utah Nevada Mining Co., in 1945 and by the Atolia Mining Co. in 1946. The owners are now doing some exploratory work."

Jan 1, 1950

The Mount Morgan eopper-gold orebody is contained within a series of Mid-Devonian volcanics which occurs as a roof pendant within Permian granite. The ore minerals comprise pyrite, chalcopyrite, and local aggregations of magnetite and pyrrhotite. Silver-rich gold (electrum) is disseminated through the ore usually in ultrafine to sub-microscopic dimensions. Accessory minerals include marcasite, digenite, chalcocite, covellite, sphalerite, bismuthinite, molybdenite, calaverite, petzite, and cassiterite.Very minor accessories include cubanite, tetrahedrite, galena, arsenopyrite, hematiIe, goethite, and rutile. The gangue minerals are quartz, predominantly, with minor amounts of chlorite and sericite.Study of microtextures of a representative suite of specimens from Mount Morgan does not reveal any criteria indicative of metasomatic replacement but does show, in the case of pyrite, evidence strongly suggestive of annealing recrystallization. Other textures in pyrite indicate porphyroblastic growth of the iron sulphide.It is inferred that the Mount Morgan orebody is genetically related to the volcanic rocks and was later contact metamorphosed by the intrusive granite or by the series of intermediate to basic dykes that transect inmine area. On this basis the Mount Morgan orebody would be a contact metamorphosed volcanic hydrothermal deposit emplaced, according to recent studies, along a pipe-like zone of brecciation.

Jan 1, 1967

By B. W. Gandrud

In July 1948, the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama and mine operators, published Report of Investigations 4306, "A Combination Cleaning and Dewatering Process for Treating Fine 'Sizes of Coal, Preliminary Report In this report a new process, referred to as kerosene flotation; was described, and results of experimental work with the process Previous to the fall of 1947 were given, The contents of the report. were summarized on pages 19 and 20' as follows: In coal-preparation plants using wet methods of cleaning, the most difficult problem is the cleaning and dewatering of the "fines" from about 10-Mesh to 0. A combination proceed is now under investigation that shows promise of practically and feasibly solving this problem. The process is similar to froth flotation, but a generous quantity of kerosene is used as one of the reagents, and the feed is from approximately 10-mesh to 0 considerably coarser than the usual froth flotation feed. The kerosene and the coarseness of the reed result in a floated product that, under certain circumstances, can be dewatered satisfactorily by a simple process of mechanical squeezing, Squeezing is accomplished by means of an ordinary conveying' Auger-and trough assembly with a section of pipe easing at the outer end of the trough. The bottom of the trough and. casing is fitted with wedge-wire sections to permit escape of the water freed by the squeezing action of the auger. On account of the important role of the kerosene, the process has been referred to in this report as kerosene flotation. Up to now, the investigative work has been divided about evenly between the laboratory and commercial plants. Nearly all of the work has been done on sludges containing the solids from the underflow of dewatering screens. A few runs have been made on 10-mesh to 0: fines from raw coal, but in some of those runs the dewatering mechanism, failed to function.

Jan 1, 1950

By Jefferson Monteiro Oliveira

As grandes manutenções (Major Overhauls), para a turbinas a vapor têm seus prazos e escopos definidos por critérios técnicos tais como a características das máquinas, condições operacionais e especificações dos fabricantes. Estas revisões têm por objetivos prever e mitigar falhas garantindo a disponibilidade operacional e a longevidade das turbinas. A inobservância destes prazos pode ocasionar falhas catastróficas e grandes prejuízos operacionais e financeiros.

Aug 17, 2017

By Amilton Feliciano Castro

In this work, activated carbons (ACs) were prepared using Sewage sludge as starting material. The ACs were pyrolyzed in an inert atmosphere at 550 °C after independent chemical treatment with ZnCl2 or KOH with ratio of 1:1. The materials were used as adsorbents for removal of Cu(II) from aqueous solutions. The adsorbents were characterized using adsorption/desorption nitrogen isotherm, SEM (scanning electron microscopy). The results showed that copper removal could be linked to surface pH and compounds present on the surface of adsorbent. KOH-treated adsorbent has smaller surface area (186 m2 g-1) than ZnCl2-treated adsorbent (192 m2 g-1), however, KOH-treated adsorbent exhibited higher removal of Cu(II). The performance of KOH-treated adsorbent could be attributed to the presence of basic groups on the adsorbent surface. Liu isotherm model gave the best description of the equilibrium data. From the Liu isotherm, the maximum adsorption capacities at 298 K for KOH-treated, ZnCl2-treated and sewage sludge (without inorganic activation) adsorbents are 31.85, 19.79 and 3.513 mg g-1, respectively. The best desorption experiment was obtained using 1.50 mol L-1 of HNO3 as eluent. Recoveries of Cu(II) from Cu(II)-loaded adsorbents are 98.9% (ZnCl2-treated) and 95.5% (KOH-treated.

Aug 17, 2017

By D. Jepsen

Land access and tenure certainty for exploration and mine development is absolutely critical to the foundation of a healthy, sustainable and environmentally-sound mineral exploration and mining sector. Without certainty, mineral exploration will be severely eroded, resulting in reduced possibility of discovering and developing new mines. The development of positive relationships based on a shared commitment of understanding, mutual respect and trust by First Nations and the mineral sector can provide this increased business certainty and social and economic benefits for local First Nations. As a sector, we face many challenges in regard to building relationships with First Nations. The root solution to addressing these challenges lies in recognizing and understanding the unique cultural differences that exist between indigenous people and the business community. From the Canadian perspective, the First Nations culture differs vastly from non-Aboriginal culture. It is equally as imperative that cultural differences be acknowledged and respected at home as they are when seeking business opportunities in other countries. The traditional “business” approaches and relationships that one understands and incorporates with one’s contractors, legal counsel, investors and Board are generally not be the best approach for the introductory and subsequent meetings with indigenous peoples. This paper is written from the perspective of my experiences accumulated over the past ten years, first as Manager of Aboriginal Affairs for one of the largest forest companies in British Columbia and now, as President and CEO of the Association for Mineral Exploration BC (AME BC). My opinions are not necessarily endorsed by AME BC. Before the gritty issues of consultation and benefit sharing are dealt with, it is worthwhile to clear up the confusion surrounding terminology. “Indigenous Peoples” is used in a global context; “Aboriginal Peoples” is used in the Canadian context therefore includes Métis, Inuit and First Nations Peoples. The term “First Nations”, in the context of British Columbia, perhaps has its roots in the fact that treaties have largely not been settled. Therefore it is important to reaffirm that British Columbia was not discovered. First Nations have resided in British Columbia since time immemorial.

Jan 1, 2007

By Aline Aguiar Lopes

A piora na qualidade dos minérios de ferro tem levado as empresas a adaptarem seus processos a novas condições de qualidade das matérias-primas, surgindo assim a necessidade de desenvolver estudos que auxiliem as tomadas de decisão. Esse trabalho avaliou a influência da qualidade do sínter e da composição da carga metálica na zona coesiva do alto-forno através dos parâmetros de amolecimento e fusão. A importância de se obter informações sobre a zona coesiva se deve principalmente ao fato de nessa região ocorrer a maior parte da perda de carga no interior do alto-forno. Cinco amostras de sínter de qualidades químicas distintas, produzidas nas sinterizações da CSN (Companhia Siderúrgica Nacional), foram selecionadas e caracterizadas para esse estudo. Os ensaios de Amolecimento e Fusão foram realizados no Centro de Tecnologia de Ferrosos da Vale através de um acordo de cooperação técnica entre as empresas. Os resultados obtidos mostraram que as técnicas utilizadas são adequadas para avaliação das propriedades em altas temperaturas, fornecendo dados importantes para a interpretação do comportamento da carga metálica no interior do alto-forno, como espessura e posicionamento da zona coesiva, permeabilidade e redutibilidade da carga, indicando assim, a composição da carga metálica de melhor desempenho para o alto-forno.

Aug 17, 2017

By Valérie J. Bertrand, Richard W. Lawrence, Marcos G. Monroy

Two cemented paste backfill (CPB) formulations containing pyritic tailings were leached in deionized water in flooded and alternating air-flooded environments and in a simulated acid rock drainage-type (ARD) solution. Scanning Electron Microscopy (SEM), solid phase chemistry and acid-base accounting measurements documented the weathering characteristics of the CPB samples. Short-term exposures of the portland-CPB samples preferentially dissolved the cement binder to a greater extent than slag-Portland CPB mistures. In all cases, the added neutralizing potential provided to backfill by cement was short-lived and insufficient to neutralize the acid generating potential of the mixture.

Jan 1, 2000

By William Greenawalt

The Greenawalt electrolytic copper extraction process is applicable to suitable oxide ores, sulfide ores and concentrates, and low-grade matte. The process is self-sustaining in acid on sulfide ores or concentrates, on mixed ores, on high-grade oxidized ores; and on low-grade oxidized ores the amount of acid to be purchased or manufactured is greatly reduced. The ferric iron is under easy control, and copper may be effectively deposited from solutions of any acid or iron content likely to be used in copper leaching. From 60 to 75 per cent. of the copper may be removed from the solution in passing through the electrolytic department, before returning the solution to the ore. The amount of copper requiring chemical precipitation, from the waste and foul solutions, is only about 5.0 per cent, of the total copper produced, and this 5.0 per cent. is converted into the electrolytic metal in the regular operation of the process. The entire process can be made practically automatic, and can be carried out mechanically. There is no uncertain departure of any kind in the application of the process; no unusual or unproved apparatus is used. EVER since electrolytic copper refining gave promise of success, about a half century ago, efforts have been made to apply the idea to the extraction of copper from its ores. The methods of attack have, usually, been to leach with a dilute acid and then to deposit electrolytically the copper from the resulting solution with the simultaneous regeneration of the solvent used in the process. Many efforts have been made, and many patents have been taken out, both in the United States and abroad, to give this idea practical application, but only within the past few years have the difficulties been surmounted. Leaching and electrolysis, as applied to copper ores, are among the most promising fields in modern metallurgy. New conditions are arising, which will bring the wet methods into prominence; while high freight rates and increasing cost of fuel will tend to limit smelting to highly favored localities. The possibilities offered by the installation of hydro-electric plants and the greatly enlarged range of power transmission will greatly widen the field of electrolytic methods.

Jan 1, 1924

By O. A. Ojo, D. L. Chen, N. Zhou, J. Q. Zhang, A. K. Khan

Dual phase (DP) steels are designed to consist of hard martensite dispersed in a relatively soft ferrite matrix, which offers a favorable combination of high strength with good deformability. Fiber laser welding (FLW) is becoming increasingly important for joining advanced materials due to its flexibility and deep penetration. In this study, the microstructure of a dual phase steel, DP980, welded by FLW technique was carefully analysed. Gleeble thermo-mechanical simulation coupled with analytical transmission electron microscopy (TEM) revealed that the FLW process produced significant microstructural changes in a narrow heat affected zone (HAZ) and fusion zone (FZ), which can result in dramatic changes in mechanical properties. This is reflected in the micro-hardness profile obtained across the welded material. The salient phase transitions induced by the FLW, including the formation of new martensite grains in the upper-critical HAZ and FZ, are discussed.

Jan 1, 2014

Any future developer of underground mining on the Bendigo goldfield will need to understand the unique geology and gold occurrence of this field. The development and sloping system employed will be primarily designed around these unique features. Modern techniques and equipment used in narrow vein mining will be applicable in this situation.The purpose of this paper is to examine the important geological features of the field as well as the known historical occurrences of the type of gold deposition in the ore bodies. This information will point to a system of development and extraction which will accommodate these features.

Jan 1, 1993

By Richard A. Allwes

This U.S. Bureau of Mines report presents the results of structural analyses and full-scale physical tests conducted on a steel-set arch and tri-set. The purpose of the analyses and tests was to evaluate the suitability of these structures for use in roof-fall prone areas. The arch canopy test and design procedures previously developed by the Bureau were utilized in this evaluation. Theoretical resistance functions were established for the steel-set arch and tri-set and were representative of the experimental behavior of the structures. The resistance functions were used to determine the energy absorption capacity of the structures and to predict their dynamic response to impact loading. The dynamic tests demonstrated that the arch canopy design procedure is appropriate for tri-sets and yields conservative designs for both steel-set arches and tri-sets. As a result of this work, it is recommended that these two structures may be considered for use in roof-fall prone areas and for rehabilitation work, provided the arch canopy design procedure is utilized for each application and the principles underlying the design procedure are understood.

Jan 1, 2010