Search Documents

By Walter I. Enderlin

To economically extract ore from great depths in the earth while sustaining an acceptable working environment will require the development of new technology and equipment, involving large capital expenditures. Moreover, careful analysis and advance planning will be required. But, the literature is lacking in data pertaining; to the thermal properties of various host rocks and to quantities of heat generated by various underground heat sources. This types, of data is required to forecast nine heat loads during advanced planning and design. This thesis sets forth a practical method for evaluating underground sources of heat in deep mines and provides an improved information base. Moreover, seven topics for further research are recommended. The heat sources considered are: wall-rock, ground water, adiabatic compression, equipment, service lines, blasting, metabolism, curing of cement, and oxidation of sulfides and timber. Seven deep metal mines with high production rates and high heat loads were visited to obtain data necessary to assess their thermal environments. Mine records were examined, wall-roc:, temperatures were measured and a survey of the mine ventilating air and mine drainage was performed. Also, the thermal conductivity of wet and dry specimens of the host rock were measured in the laboratory. Data analysis disclosed that rock heat and adiabatic compression account for stout 60 per cent of the mine heat load at depth. Equipment currently contributes approximately 20 per cent; however, to offset increasing costs with depth, increased mechanization is anticipated. The treat from ground water averages 19 per cent and the contribution from blasting, metabolism and cement is negligible. Also, approximately [0] per cent of the increase in the enthalpy of the ventilation air is in the form of latent heat. Moisture, however, did not significantly affect the thermal conductivity of the rock specimens measured in the laboratory. Also, from the data, it is evident that a negative correlation exists between the thermal conductivity of the host rocks and the per cent of the heat load derived from the wail-rock. Furthemore, steady state heat flow renditions may be assumed in airways where there has been no major changes in the ventilation system for a period of two years or more. Under these conditions, the author found it more convenient and reliable to compute heat influx using the steady state equation for heat flow into a cylinder, rather than Carrier's method for transient heat flow, which is so often used.

Jan 1, 1973

By R. Frank Chiappetta

A new blasting technique has been developed by International Technologies, LLC. to eliminate subgrade drilling, lower ground vibrations, improve fragmentation and reduce explosive consumption. The new technique utilizes a uniquely designed borehole plug, with a bottom hole air deck and a predetermined stemming mass on top of the plug. This combination is referred to as the Power Deck?. Single holes and full scale tests were conducted by Blasting Analysis International, Inc. (BAI) to determine how the system works, the mechanisms behind its success and the best design parameters to use for the given rock conditions. Results have shown reduced or eliminated subgrade drilling, ground vibration reductions of up to 33%, reduced explosive consumption by 16 to 25%, and improved fragmentation by up to 25%. This paper summarizes the methodology, field test setups, analyzes procedures and results for one series of single hole and full-scale tests which were performed in a Pennsylvania, USA quarry.

Jan 1, 2004

By D. C. Oliver

Paper written on project work carried out in partial fulfilment of B.Sc. (Eng.) (Metallurgy and Materials) degree Corrosion in exhaust systems can occur on both the interior and exterior surfaces. Chloride-containing de-icing salts on the roads in colder countries greatly increases the rate of corrosion on the exterior surfaces. This paper investigates the relative exterior corrosion resistance of three alloys?two ferritic stainless steels( AISI Types 409 and 441) and an aluminized mild steel. The exhaust system is split into two categories?the hot end and the cold end. A test for each of these ends was designed?the standard ASTM G85test was modified to create a simulated driving cycle. The cold end test samples were exposed to ten driving cycles, and the hot end test samples were exposed to five driving cycles. A driving cycle constitutes the car being started from cold, driven until the operating temperatures are reached, and switched off and allowed to cool. Pitting corrosion is the primary corrosion mechanism occurring at the cold end of the exhaust system. The aluminized mild steel was the most resistant alloy in this test, and Type 409 the least. However, once the protective aluminium layer degrades, corrosion will occur rapidly. At the hot end of the exhaust system, spalling of the surface oxide layer is the primary corrosion mechanism occurring. Type 441 was the most resistant in this test, and the aluminized mild steel the least resistant. Potentiodynamic tests were performed on the alloys?the results agreed with the results obtained in the exposure tests.

Jan 1, 2003

By Laís Couto dos Santos

A corrosão é definida como um conjunto de fenômenos de deterioração progressiva dos materiais em consequência de reações eletroquímicas. Em determinadas instalações metálicas, tais processos são monitorados através de cupons de perda de massa. Quando tal fenômeno se evidencia pela formação de cavidades com pouca perda uniforme, consistindo em um processo de corrosão puntiforme, ele é denominado corrosão por pites. As normas ASTM G46-94 (2005) e NACE RP0775 (2005) recomendam caracterizar a corrosão por pites através da densidade, tamanho, profundidade e taxa de corrosão por pites. Entretanto, essa é uma avaliação subjetiva e o fator humano pode ter influência significativa na obtenção dos resultados. No presente trabalho, cupons de corrosão comerciais foram expostos à corrosão em câmera de imersão no período de três meses, tendo como fluido a água potável. O objetivo principal foi avaliar a influência do fator humano nos parâmetros de corrosão puntiforme. Foi realizada uma análise comparativa dos resultados obtidos por três diferentes operadores. As alterações encontradas se mostram significativas, entretanto, tais variações não modificaram o nível de classificação dos cupons segundo as normas.

Aug 17, 2017

"Tell us how you got involved in mining?I was first exposed to mining at a young age, as a consequence of my dad and his passion for the industry and rock collecting. Even though he graduated with a degree in mining engineering from Washington State University, my dad spent most of his career working as a structural engineer for the Boeing Company. At the time, Boeing supported a range of employee activities and clubs, including one devoted to mineral prospecting, small-scale dredging and rock hounding. My dad was extremely active in the Prospectors Club, where as a family, we spent a good part of my youth tramping around the Pacific Northwest digging for mineral specimens and panning for gemstones and gold. On my mother’s side of the family, I had relatives that mined in Dawson City and Fairbanks, AK which left a family legacy of sorts. I loved the stories that my dad and a close buddy of his, who was a geologist, would tell about various operations and towns, as well as the wild times at the annual Northwest Mining Association (NWMA) meeting in Spokane, WA. My first recollection of ever being at a commercial operation was during a tour of the Bunker Hill Mine with my dad when I was 7 or 8 years old; this had to have been shortly before the May 1972 fire at Sunshine. That visit of the mine and processing facilities made a permanent impression on me. While I always knew there was something special about the Silver Valley, I began to understand why. To this day, I still get the same feeling when I visit historic mining districts like Leadville, Morenci, Virginia City, Butte, Silverton and Barkerville. During our summer excursions to Helena, MT to dig sapphires, we would usually make visits to Butte and watch mine operations inside the Berkley Pit and surface activities at the Kelly and Mountain Con. In high school, I did well in math and science and began entertaining thoughts of pursuing a degree in engineering. Above all, I wanted to go to a college in the West that had a good academic reputation, where I could also play football. As a 6-ft, 190-lb nose guard, my options for a Division I scholarship were pretty slim, and there weren’t that many technical schools in the Northwest that were Division II that offered athletic scholarships. As fate would have it, I was unexpectedly contacted by Marv Kay, a legendary coach at the Colorado School of Mines (CSM), and was recruited to play ball. Fortunately, I had a couple of high school friends who were already attending CSM, and I had just secured a summer internship with Asamera Minerals in Wenatchee, WA. It was as if all the stars had aligned, and, with the support of my parents, I made the decision to attend Mines. Despite the stress of getting through CSM during a period when the mining industry was in freefall, it was a great decision to attend Mines, and I’m thankful for all the opportunities, friendships, and faculty mentoring I received as a student"

Mar 1, 2019

By Ewan Wingate, Ranjit Prasad, Yanjun Liu

The phosphorus journey begins with the extraction of primary phosphorus in the form of phosphate in apatite through openpit mining and, in some rare cases, underground mining methods. The ores are processed in beneficiation plants to remove impurities before the phosphate rock concentrate is either sold on the open market or converted into phosphoric acid in downstream chemical production facilities by the wet acid process or thermal phosphorus routes. These can in turn be converted into fertilizers, as well as used in the food and electronic industries. The advent of the EV battery has given rise to a new use for purified phosphoric acid in the production of lithium ferro phosphorus (LFP) cathode material for EV battery cathode assemblies. The production of LFP relies on raw materials such as lithium carbonate, lithium hydroxides, iron salts and purified phosphoric acid.

Feb 1, 2024

By Earl T. Hayes

[This work represent a continuation of the efforts of the Metallurgical Division of the Bureau of Mines to ascertain and apply knowledge of miner physics to processes metallurgy.]

Jan 1, 1941

By Earl T. Hayes

[This work represents a continuation of the efforts of the Metallurgical Division of the Bureau of Mines to ascertain and apply knowledge of mineral physics to process metallurgy.]

Jan 1, 1941

By Lloyd A. Morley

This annual report details progress under USBM Grant G0155003 during the project period of January 1, 1977 through December 31, 1977. The report contains four principal chapters covering accomplishments in the mine electrical safety research areas of continuous monitoring, battery and battery-charging safety, and computer modeling. Highlights of the work are summarized in the last report chapter.

Jan 1, 1978

By Paul Guliov

Industrial clays, including a variety of bentonites and kaolinbased clays in southern Saskatchewan are hosted by Late Cretaceous and Early Tertiary sediments. Ofparticular significance are the deposits of swelling bentonite in the Cretaceous Bearpaw Formation and the kaolinitic clays of the Cretaceous Whitemud and Paleocene Ravenscrag Formations. Swelling bentonite is currently produced in the Wilcox-Truax area by Canadian Clay Products Inc. and yields at least seven different commercial products for a variety of applications. Kaolinitic plastic clays, including ball clay, stoneware and earthenware clay, as well as kaolin in southern Saskatchewan, have a long history of development and use. Products include common and face brick, refractory bricks and other shapes, chinaware, pottery, sewer pipe, chimney flue linings and tiles. Currently clay production is for out-of-province brick manufacturing and for pottery. Recent research and improved technology combined with expansion in certain areas of the global clay industry generally hold promise for a resurgence of a clay-based industry in Saskatchewan. Products of particular promise include: clay tiles; kaolin fillers and extenders; and aluminum as well as related by-products from kaolinitic clays based on the carbochlorination process.

Jan 1, 2001

By C Moorhead

The classification of Mineral Resource estimates for reporting in accordance with the JORC Code is a statement of the Competent PersonÆs confidence in the estimate and an attempt to convey that confidence to the various users of the resource estimate. In general the classification process is either largely subjective, relying on the Competent PersonÆs experience, or relies on statistical measures derived from the estimation process. These statistical measures may not necessarily relate to the overall confidence in the resource which must also take account of the confidence in the geological inputs to the estimation. Several authors, including Jackson et al (2003) and Dominy, Noppe and Annels (2004), have addressed methods of including consideration of geological data and its reliability into the classification process. Henry and Parker (2005) have discussed a quantitative measure for classification of Measured and Indicated Resources related to mine production parcels. These methods rely on the availability of sufficient information for the application of geostatistics, data evaluation techniques or repeated interpretation of data to provide an indication of confidence. They are suitable for very advanced projects. In 2005, using a modification of the financial audit æcontrol and quality criteriaÆ principles, then widely accepted within Newcrest Mining Limited (Newcrest), the principal author developed a scheme which categorised the classified resources into æcontrolÆ and æqualityÆ (or risk) categories. Control covers all aspects of the data collection, the geological interpretation, the data analysis and the modelling of tonnage and grade; it is also influenced by the documentation of the estimate. The quality criteria are a subjective measure of risk associated with the estimation of the resource and refer to the risk that the tonnage and grade are not realised and the consequences if decisions are made on the basis of these estimates. By evaluating the generally accepted level of risk attributed to these quality ratings by Competent Persons within Newcrest, a graphical representation of the confidence in the resource ounces was prepared for communication of the expected confidence in the resource statement.

Jan 1, 2009

By D MacKay

The Mt Wright Project is located near the town of Ravenswood in North Queensland and is operated by Carpentaria Gold – a wholly owned subsidiary of Resolute Mining Limited. Underground Development of the current Mt Wright orebody commenced in June 2006 and the first production ore was brought to surface in June 2007. The orebody is a rhyolite pipe containing fine-grained disseminated gold in a granite host rock. Ground conditions tend to be good to excellent throughout development, with some minor deformation experienced when stope-sized excavations are formed. The mine commenced as a sublevel open stoping (SLOS) operation with the intent to utilise development waste to back fill isolated upper level stopes while developing to the bottom of the known orebody. The mine plan intended to commence production with a bottom-up primary/secondary stoping retreat through the main orebody utilising cemented fill. Some challenges were faced during the initial production phase that included:•Ongoing underground diamond drilling and updating of the block model resulted in some issues reconciling the grade control results to the resource model. This was primarily due to the high variability of grade which in turn caused difficulties in accurately identifying areas of low and high-grade.•The cost of establishing and operating a cemented fill plant to achieve the planned extraction sequence of the orebody had increased significantly beyond initial estimations.•Geotechnical conditions such as stress orientations, ground behavior and response to the forming of excavations learned through the mining of the upper level stopes were different to the assumptions made during the initial design.A number of in-house and external reviews of the mining method were completed which has resulted in a revised mining plan. This paper will summarise the challenges faced and the implementation of the mine plan to date.

Mar 21, 2011

By B Hawkins, S Durkin, V Lawrence

The requirement for secondary egress from underground workings has long been regulated in Australia. Escape way systems have evolved from simple airleg rising ladders and timber ladders to steel galvanised ladders and more recently fully enclosed polyethylene ladders.The polyethylene ladder, Safescape Laddertube, was introduced to the underground mining industry in 2010. It is an enclosed cylindrical modular plastic ladder designed for use in underground escape ways and access ways. Since its first installation in May 2010, the Laddertube has been installed in 43 mines across four countries, totalling 8800 m of ladders installed to December 2013.The Cracow Gold mine is one operation using Laddertube, located 500 km north-west of Brisbane, Queensland, Australia. Upon discovering and developing both the Empire and Roses Pride orebodies, a safe and economically viable secondary egress system and surface primary ventilation exhaust shafts were necessary to support development and production activities to these workings. The need arose to merge these two critical requirements together between surface and underground mine workings some 200 m and 400 m respectively for each orebody. Neither egress has intermediate access points within their full service length from top to bottom. Several options were considered, the preferable and most feasible method adopted was Laddertube.The longest egress length requiring Laddertube within the two vertical surface exhaust shafts was 400 m long, within a 3.5 m diameter shaft. Due to the length of the vertical Laddertube system in both egresses, personnel are to be assisted by mechanical means using the Extended Ladder Climb Assist system.The Gossan Hill mine also uses Laddertube for their escape ways. Part of the Golden Grove operation, Gossan Hill is an underground sublevel open stoping mine located in the mid-west of Western Australia.With a considerable mine life remaining and a history of acidic water and stress related deterioration in vertical openings, the mine operators sought an escape way solution that would provide for the long-term needs of Gossan Hill. Laddertube was selected due to its non-corrosive properties and the ability to fill in around the ladder way to provide stability to the raise opening.Laddertube is a recent development in escape way systems, and is effectively being applied in a variety of operations, meeting the specific needs of underground mines.CITATION:Durkin, S, Hawkins, B and Lawrence, V, 2014. The application of Safescape Ladders at the Cracow and Golden Grove operations, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 311–318 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By Daniel G. DiCanio

This report describes a computer-based model for estimating the tangible costs of injuries and deaths from work-related accidents in underground coal mines. The study undertook to identify and quantify the elements of accident costs, including field visits to coal mines, insurance carriers, and public agencies. The mathematical models developed for each tangible element of accident cost are presented in Volume I -of the report. A listing of the computer programs which comprise the model and instructions for using the programs are presented in Volume II. Statistical distributions of mining family characteristics, data on 95 miners killed in underground accidents, and other basic data used to develop the model are presented in Volume III. Application of the model to a data base of 9,286 accidents which occured in underground bituminous coal mines during 1974 yielded a total of $56,900,000 in tangible costs to industry, mining families, and public agencies. Loss of income to the families of miners injured or killed in these accidents accounted for 47 percent of the total.

Jan 1, 1976

By Robert T. Davis

An award is a form of recognition given for superior performance in a special field of endeavor. Each year awards are given by the Joseph A. Holmes Safety Association and the National Safety Council to the coal-mining industry's underground and open-pit mines that have worked a specific number of man-hours without a lost-time injury. These awards have a dual significance in that they prove efficiency can be attained without injury to persons. Safety awards do not result from luck or good fortune but do result from sincere desire coupled with sufficient effort and cooperation to achieve a desired goal.

Jan 1, 1964

By Louis J. Mittoni

"It is well known that gas injection systems can exhibit a wide range of dynamical behaviours, ranging from linear periodic bubbling through to highly complex turbulent jetting. Recently, it has been observed that an important intermediate regime exists under certain system conditions, where the dynamics are complex in nature yet predictable for short time periods. This paper reviews the evidence to support the above hypothesis, and discusses the invariant quantitative measures such as density, return maps, Lyapunov exponent and dimension which may be used as pattern recognition features in a mOnitoring and control strategy.INTRODUCTIONThere has been a great deal of research on the submerged injection of gases into liquids. This interest is primarily due to the large number of applications in the pyrometallurgical and chemical engineering industries. Gases are typically injected into liquids to achieve goals such as heat and mass transfer, or physical mixing and agitation. Only recently though has the possibility of using the evolution of the gas dynamics as a probe to internal system conditions been raised [1, 2].At very low gas injection rates and small upstream chamber volumes, gas normally disperses in the form of stable bubbles of constant volume [3]. With increases in gas flow rate, the dynamics become more complex, bifurcating into double bubbling, multiple bubbling and complex coalescence behaviour. Irregularities measured in pressuretime series acquired upstream of the injection port under these complex conditions have usually been treated as bothersome noise or contamination to be filtered from the signal and ignored in the analysis. These irregularities, however, may contain physically interesting and useful information on the system from which they were produced if the system may be classified as deterministically chaotic [4]."

Jan 1, 1996

By Ashley Woodward, S. Katharine Hammond, Mayela Padilla-Salas

This paper presents a scalable framework for worker safety assessments. The paper focuses on uranium mine reclamation in underserved communities, specifically Cove Chapter of the Navajo Nation. By integrating field observations, OSHA data analysis, systems mapping, and a hierarchical occupational health pyramid, this framework identifies site-specific hazards while addressing broader socio-cultural dynamics. The approach improves upon existing safety programs by suggesting actionable, locally sensitive solutions that prioritize higher-order controls such as hazard engineering interventions and administrative controls. This study contributes to enhanced worker safety, efficient environmental restoration, and engagement in marginalized communities with abandoned mine lands.

Feb 22, 2026

By Donald Bruce, Alex Reeb, George Filz, Wesley Schmutzler, Mitsuo Nozu

"One million seven-hundred thousand cubic yards of deep mixing were installed to support an elevation raise of an earthen levee known as LPV 111, which is located in east New Orleans. The deep mixing was done by two contractors using somewhat different technologies, but producing elements of the same size. As part of the quality control and quality assurance program, 507 deep-mixed elements were cored and 5,082 specimens were strength tested in unconfined compression. This paper presents data from the coring and testing program. Very high percentages of the core run lengths were recovered, except during one period for one mixing technology. The coring methods are described, and reasons for the isolated episode of low recovery are discussed. The strength data show that the specification acceptance criteria were satisfied. Statistical parameters of the strength data are provided, and trends between strength and the following factors are discussed: depth, soil type, binder factor, and project-specific experience. Photographs of longitudinal cuts of core specimens are presented. Important lessons learned from this unusually large project are described.INTRODUCTIONThe Lake Pontchartrain and Vicinity Hurricane Protection system included a project known as LPV 111, which is an approximately 5-mile long segment of levee and floodwall located in east New Orleans along the Gulf Intracoastal Waterway and adjacent to Bayou Sauvage National Wildlife Refuge (Cali et al. 2012). The majority of the project consisted of a raise of an existing earthen levee from an existing crest elevation of about 18 ft to a new crest elevation of about 28 ft. The underlying soils were weak and compressible, providing inadequate support for the raised levee. Ground improvement in the form of deep mixing was selected to provide the necessary stability and settlement control for the raised levee.The US Army Corps of Engineers (USACE), New Orleans District, was the governmental agency in responsible charge of the project, including approval of design, construction, and payment. The lead designer was URS Corporation, and the general contractor was Archer-Western-Alberici (AWA), working in alliance with TREVIICOS South (Trevi), who, together with Fudo Construction (Fudo), performed the deep mixing.As part of the quality control and quality assurance program, over 500 production deep-mixed elements were cored, the cores were carefully logged, and over 5,000 unconfined compression tests were performed. In addition, selected specimens were carefully photographed before and after longitudinal saw cuts to expose the interior of the specimens. This paper provides a summary of the coring and testing performed on the production deep-mixed elements."

Jan 1, 2015

By W. A. Lang

Introduction Under our present civilization, industrial developments will be greatest in those areas in which energy .can be most economically produced and efficiently used, where labour is in adequate supply, and where markets for the products of industry are available. A knowledge of fuels- the present major sources of energy- and of their utilization is therefore of vital importance. With that in mind, the aim in this paper will be to outline the known reserves of fuels in Alberta, to give their characteristics, to indicate the markets served by each, and to offer some suggestions for the future development of the coal industry. The paper should be regarded as a compilation of published data rather than as an original treatise. Alberta is richly blessed by having large reserves of mineral fuels. The estimated reserves of coal are 46,562 million tons. Alberta is the oil and gas province of Canada. The world's largest deposit of bituminous sand occurs along the Athabaska river in Alberta. In addition, there are large areas of forested land in the northern and western sections of the Province, and the rivers serve for the development of hydro-power.

Jan 1, 1949

By AIME AIME

CERTAINLY in point of attendance, and doubtless in several other ways as well, the 147th meeting of the A.I.M.E. was the best ever held. In times of depression, mining engineers and metallurgists have plenty of time to come to the Annual Meeting but money is scarce; at the height of industrial activity they have plenty of money but no time. "The current period of transition seemed to provide ideal conditions for' both the preparation of papers and attendance at their presentation. The weather made even the Californians present envious though the weather man gets no credit, for rain and snow was what he willed. Among the elevator men, the miners have the reputation of being the toughest crowd to handle, though the best natured, withal, of all the engineering groups that meet in the Engineering Societies Building. This year Your inquiring reporter was told, "it was the damnedest meeting I ever saw; they

Jan 1, 1937