Search Documents

By N McKenzie, F Brodbeck

The North-South Bypass Tunnel is the first project to get underway as part of BrisbaneÆs transport plan, which aims to improve the urban road network. The total length to be excavated is 6.8 km, which includes 4.8 km of driven tunnel and associated road connections. Construction commenced in August 2006 with project completion targeted well before the contractual completion date of October 2010. Due to the local geology, in particular the hard Brisbane tuff and neranleigh-fernvale formation, a combination of tunnel excavation methods are used. The majority of the tunnel is excavated by two tunnel boring machines which have a rate of progress of 16 - 20 m per day in rock having a compressive strength of between 80 and 150 MPa. Ten roadheaders operate at a rate of up to 2 m per day excavating the remaining tunnels, such as ramps, access tunnels, cross passages and merges. The tunnel team are managing the challenges and complexities associated with tunnelling through the hard Brisbane rock. A major challenge arose during the planning of the initial mainline excavation underneath the Royal National Association Showground in Bowen Hills. This section contains low rock cover and historical maps indicate that the showground is located within a former topographic depression (alluvial valley), which a creek once flowed through.Due to traffic merge design requirements, both tunnel boring machine (TBM) and roadheader excavation methods were required to be used in this challenging geological profile. The answer was to stabilise the alluvium above both TBM section tunnels from the surface prior to excavation and to operate the TBM in single shield mode with immediate grouting of annular void from the tail shield. In addition, the roadheader section of tunnel required additional support by spiles and canopy tubes installed from the tunnel face.

Jan 1, 2008

By Kotaro Ogura

"The electrolysis process in which CO2 is selectively reduced to C2H4 at a three-phase(gas/solution/metal) interface on a copper-mesh electrode has been developed in a concentrated solution of potassium halide. At open-circuit potential, CO2 is captured on the electrode by being inserted into the double-layer consisting of halide anions specifically adsorbed and potassium cations which are located in the Helmholtz inner and outer layers, respectively. CO2 thus activated is subjected to the electrochemical reduction. In the early stage of reduction, CO2 is converted to formate radicals that are adsorbed on the electrode by taking the place of halide anions. The reductive coupling of these radicals results in the formation of intermediates such as -CH2C(O)- and CH2=CH-, and C2H4 is finally produced. The catalytic activity of the electrode process involving the insertion of CO2 into the double layer is not deteriorated at all during the electrolysis, and the continuous reduction of CO2 to C2H4 is possible with the addition of inorganic acid under the assistance of natural energy.Carbon dioxide is a serious pollutant released from fossil fuel power station, internal combustion and many industrial operations. The easy release of CO2 to the air has caused the global warming, and the technique which intends to curtail CO2 by pushing it back into the ground has been suggested. However, this problem should be greatly mitigated if CO2 can be converted to innocuous substances. Especially, the reuse of CO2 as fuels and chemicals is extremely effective not only for the mitigation of the global warming but also against the depletion of the fossil fuel reserves. Several processes for converting CO2 to valuable compounds have been proposed including hydrogenation over heterogeneous catalyst at high temperature and electrochemical and photochemical reduction. In the conversion and cutback processes of CO2, however, it is of importance that the process is feasible under mild conditions, because the secondary generation of CO2 is feared if high energy is required and supplied with a fossil fuel. In this meaning, the electrochemical reduction of CO2 taking place at room temperature, which is similar to photosynthesis, is promising. From the practical point of view, it is further necessary that the conversion rate is high enough and the product is satisfactorily valuable."

Jan 1, 2008

By Roozbeh Afzali

Designing an appropriate tunnel blasting pattern reduces the cost of rock breakage and subsequent operations such as loading, haulage and support of tunnels. For that reason, we developed a software that designs tunnel blasting patterns. Using this software, three different tunnel blast design models based on parallel hole cut, namely, Swedish, Konya and Energy Balance, were investigated and compared for a virtual tunnel. Accordingly, blasting patterns were designed, for different cross sections. The trend of parameters such as specific charge and specific drilling as functions of tunnel cross-section was determined for each model. Our results show that, in general, The Swedish model gives lower specific charge and specific drilling compared to other models.

Jan 1, 2008

By Frank Rausche

Although Quality Control (QC) during construction is preferable for deep foundations, there are many instances when it is necessary to resort to Quality Assurance (QA) methods if, for various reasons, QC is not possible. Non Destructive Testing (NDT) methods for deep foundations are indirect approaches, i.e. in complex situations they do not provide complete information and need to be augmented by additional testing and/or analyses. While the challenges are varied for the different deep foundation types and the different test methods they are the same in many different countries. Experience of the tester is often mentioned as being most important for a successful quality assurance. In addition, reliable testing equipment for the best possible measurements and complete construction documentation for a meaningful data interpretation are minimum requirements for a successful test outcome. Another problem is the widely varying cost of the QA tests. For that reason the specifying engineer or authority has to be aware of what can reasonably be expected so that technically feasible specifications can be written for optimal cost and minimal construction delays. This paper discusses the most common NDT methods with a view on how these methods are applied world wide. It summarizes features of specifications, recommendations for test procedures and advanced analysis methods which can help to overcome uncertainty in the quality assessment of the foundation. Finally, the authors propose a decision tree for various QA methods, deep foundation types and soil properties.

Jan 1, 2008

By R Fleming, G Jones

An ocean outfall is currently under construction in Christchurch, New Zealand to transfer treated wastewater from the existing treatment ponds at the city wastewater treatment plant to diffusers located 3 km offshore. The New Zealand $85 million project comprises a new pump station and 5 km of 1800 mm diameter pipeline with a design capacity of 6.0 cumecs. The pipeline comprises 2.3 km of concrete pipe installed by microtunnelling and 2.7 km of polyethene marine pipe installed by dredge and lay. This paper describes the consent process, key environmental and community constraints, the tender process, risk provisions included in the contract, the type of contract, partnering provisions, geotechnical design issues and the pipejacking construction activities and issues.

Jan 1, 2008

By Ilona Johnson

United States metals and non-metallic minerals manufacturing consume about 5,000 trillion Btu annually. Various studies estimate that as much as 20 to 50 percent of this energy is lost as excess or waste heat. Recovery of waste heat can conserve energy, reduce operating costs, and lower environmental emissions. It would be valuable to quantify recoverable waste heat sources and identify the barriers that hinder its recovery. This paper provides an overview of waste heat losses specific to high temperature processes in primary metals and minerals manufacturing. It summarizes findings from a broader study conducted for the Department of Energy Industrial Technologies Program; the study evaluates energy losses, recovery practices and opportunities, and R & D needs for waste heat technology development.

Jan 1, 2008

By Vojtech Gall

Pre-support measures for urban tunneling have seen a substantial development in the recent past. Ground improvement techniques, pipe-arch and spiling methods now allow for non-disruptive tunneling at very shallow depths under sensitive structures, rail tracks and roadways. The paper presents experience gained on national and international projects built over the past decade that represent case histories and therefore may be used as guidance for the development of similar solutions for future tunneling projects at shallow depths. Reference projects include tunnels for the Washington, DC Metro, London Underground, Dulles Inter-national Airport, Busway tunnels in Boston and the Ft. Canning Tunnel in Singapore.

Jan 1, 2008

By Tara Bajpayee

Modern, highly productive underground mining operations need to assure the safety of their workforce by understanding where major strata fractures and roof failures could occur. Mines depend on a host of tools to assess ground instability. In-mine microseismic monitoring systems with sufficient number of sensors have also been used to provide this information. These in-mine systems must be robust in design and moved regularly to keep up with the mining advancement. System performance issues depend on maintaining ever increasing cable runs, preventing component damage from mining activities (scaling, blasting, etc.) and avoiding signal degradation due to interference from mining equipment (fans, trucks, electrical equipment, etc.). A potential solution is to use a surface based monitoring system having sensors placed in boreholes above and adjacent to the underground mine workings. These sensors must be capable of detecting and locating strata fracturing associated with rock failure events. A great advantage of a surface based monitoring system is its independence from the underground mine infrastructure. There is less concern with cable maintenance problems, signal degradation by interference from mining activity, or loss of power from the mine?s power grid. The disadvantages include the cost of drilling boreholes and challenges associated with placing sensors in the boreholes, maintaining radio communication and solar power, and public interference (vandalism, etc.). This paper describes a case study where a surface based microseismic system, using triaxial geophones in boreholes drilled from the surface, was deployed at a large limestone mine. The system was operational during a roof fall that occurred in October 2007. It detected the first rock fracture event 17 minutes before the rock fall event. The geophone array was sensitive enough to identify all large rock fracture, impact, and blast events as well as medium size rock fracture events occurring close to the geophone array.

Jan 1, 2008

By Kevan J. R. Ford, Chris A. Fleming, Robert D. Henderson

"Kinross Gold Corporation’s Maricunga mine in Chile presents an ideal opportunity to apply the SART process to a heap leach operation. Given increasing levels of cyanide complexed copper in current pregnant solutions from Maricunga heaps (over 300 ppm Cu), there is a need to reduce these levels and decrease cyanide consumption and cost. Additionally, a means of disposing of this copper is required, preferably as a saleable product. The well published SART process applied to gold-copper cyanide solutions was selected as it allows rapid precipitation of cyanide soluble copper as a relatively pure copper sulphide. The process also allows effective recovery and recycle of cyanide back to the heap leach operation.This paper reviews the SART process chemistry and presents a summary of SART bench-scale and pilot plant testwork completed by Kinross. Key design parameters and engineering aspects of the proposed plant at Maricunga are discussed. SART plant operating costs and net revenue analysis are included and illustrate the compelling economics of installing a SART process plant. INTRODUCTIONMaricunga OperationCompañia Minera Maricunga (CMM), fully owned by Kinross Gold Corporation, operates the Maricunga mine (formerly Refugio) which is located 120 km due east of the city of Copiapó at an elevation of 4,200m above sea level in the Andes mountains of northern Chile. Figure 1 shows a map of the location of the Refugio mine relative to other gold and copper mines in the region."

Jan 1, 2008

By G D. Carman

White Rock is a reduced tungsten-tin skarn deposit near Rye Park, New South Wales. This abstract summarises the depositÆs mining and exploration history, and current exploration by Paradigm Metals Ltd targeting an economic resource at the deposit. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By B. Grosso

The National Italian Regulation concerning environment protection imposes that industrial areas are provided with systems aimed at preventing the circulation of contaminated groundwater. These systems can be static or dynamic and operate basically by intercepting the contaminated flow. Their effectiveness, realization time and costs depend on the intervention type and on the features of the specific site. The selection of the best solution is complex and the results obtained by this selection may be affected by residual risks related to the uncertainty of the hydrogeological and geotechnical characterization of the site. With regard to the industrial area of Portovesme, located in the south of Sardinia, the paper presents the analysis of alternative interventions aimed at the protection of the groundwater. The attention is focused on the evaluation of their effectiveness, impact on environment and, finally, time and costs of construction.

Jan 1, 2008

By C. Rodrigues

This investigation compares the gas adsorption behaviour and capacity of three bituminous coals from South Africa, of similar rank, by assessing the characteristics of the raw coal, as well as the resulting float and sink fractions (at 1.80 cm3/g) obtained by density separation of crushed coal samples. Calculations were also made to obtain the raw coal gas storage capacity from the weighted contribution of both float and sink fractions results, thereby permitting comparison with the analysed results of the raw coal. The study demonstrated that the clean fraction of a coal has the highest capacity to retain gas in the sorbed state, followed by raw coal, and lastly the sink fraction, and re?confirmed previous investigations that showed minerals to be inhibitors of gas adsorption and retention.

Jan 1, 2008

By A. C. Smith

Although only used in a few U.S. longwall mines, bleeder-less ventilation systems can be an effective spontaneous combustion control method in mines having a demonstrated history of spontaneous combustion. To provide insights for the optimization of bleederless ventilation systems for U.S. underground coal mines, a computational fluid dynamics (CFD) study was conducted to model the spontaneous heating in longwall gob areas using a bleederless ventilation system. A single longwall panel with a bleederless ventilation system was simulated, and typical longwall mine ventilation data were used in the simulations. The permeability and porosity profiles for the longwall gob were estimated using a geotechnical model and were used as inputs for the CFD modeling. The effects of gob permeability and resistance of the collapsed entries on the spontaneous heating were studied. The effectiveness of using nitrogen injection to prevent spontaneous heating in the gob was also examined.1

Jan 1, 2008

By J Parr, P Ashworth, S Johns, C Yeats, A Littleboy

The ocean floor is increasingly being discussed in terms of its resource potential. New discoveries, improved knowledge and access to unexplored areas of the deep sea and continental shelf are some factors contributing to a renewed interest in the seafloor exploration and mining industry. The industry has been referred to as the ænext minerals frontierÆ. To date, much of the research has focused on proving economic and technical viability of the industry, with environmental issues addressed locally. However, there is limited research internationally, and none known in Australia that considers the social viability of the industry, addressing issues such as regulatory contexts, international precedence and public acceptability. Does the nascent seafloor exploration and mining industry have a social license to operate? Does it have support amongst the wider community? If not, why not? The Wealth from Oceans National Research Flagship explored these questions by scoping the social issues that would surround an expansion. Two desktop studies provide insight into the current level of activity in seafloor exploration and mining, recent developments and the regulatory regimes on which the industry is based. One study focused on the situation in Australia, while the other was internationally focused. A series of workshops were held with key stakeholders from government agencies, industry and other interested parties, such as environmental groups and the fisheries industry. These workshops identified and explored the different stakeholdersÆ perceptions of the benefits, concerns, opportunities and key questions associated with an expansion of the seafloor mining industry. The desktop studies revealed that Australia is one of only a few countries with legislation specific to seafloor exploration and mining. Nevertheless, barriers to licence approval exist because of lack of precedent in applying this legislation. Consequently, the decision process can be vulnerable to political issues and subjective judgements. The outcomes from the stakeholder workshops suggest this inconsistency may be influenced by the high levels of concern and uncertainty over environmental impacts. Uncertainty over environmental impacts can influence the acceptability of an environmental impact assessment (EIA) and also mean the perception of risk is variable. Overall, this research suggests that the future of the seafloor exploration and mining industry will be highly dependent on AustraliaÆs ability to:improve the knowledge-base underpinning the regulatory regime,generate open and transparent communications between stakeholders, andimprove the understanding of policy and regulatory processes.

Jan 1, 2008

By Eric Jackson

The presentation describes the operation and field test results of a seafloor massive sulphide prospecting system. The prospecting system is deployed from a work-class ROV, and it features a new and innovative electromagnetic ocean floor conductivity sensor. It also includes magnetometers, a multibeam sonar, and subsea cameras. The prospecting system has been used in two exploration campaigns - one in the territorial waters of Papua New Guinea (PNG) in 2007 and again in 2008 in both PNG and Tonga waters. The 2007 campaign used the prototype sensor, and the 2008 campaign used a Mark II version. Correlations between drill core samples and EM conductivity results are excellent. New prospecting system data will be used to help plan future core drilling locations. The presentation discusses the principle of operation of the EM conductivity sensor, discusses improvements made in the EM sensor and the overall prospecting system, and shows exploration results. Keywords: seafloor massive sulphide, geophysics, ocean floor, subsea, electromagnetic, conductivity, magnetometer, multibeam, core drilling

Jan 1, 2008

By Jeffrey Whyatt

Mining coal in deep, gassy strata is difficult, particularly in deep mines of the west. Dynamic failure (bumps, bounces, etc.) is commonplace, particularly where strong sandstone strata are encountered in the overburden. The disaster potential posed by dynamic failure in these mines is examined and found to be significant. Recent trends in MSHA reportable bumping of deep western coal mines have been increasing. Recent clusters of bumps are explored, a number of which have ended badly. The mechanisms of these bumps and their interactions with geologic structures are explored. Significant progress in controlling these hazards depends on a full understanding of their interaction with geologic conditions. It is apparent that not all MSHA reportable bumps have the same mechanism. These reports describe bumping of pillars, rolling of ribs, outbursts of coal, heaving of floor, shaking-induced roof falls, etc. Progress depends on understanding the underlying mechanisms of these events, and then determining which are potentially active at a particular location. Designs and other protective measures can then be adapted and deployed appropriately. Explicit consideration of mechanisms also supports extrapolation beyond experience as design extends into new mine geometries, geologies, mining methods and increasing depth. Finally, the goal should not be only to design hazard out of mines, but also to provide assurance that this, in fact, has occurred. Pursuit of this goal has been taken up by a major NIOSH research project. The centerpiece of this project is development of a Dynamic Failure Control Program to monitor evolution of dynamic failure hazards with changing geologic conditions to assure that control and protective measures are appropriately deployed.

Jan 1, 2008

By Caisa Samuelsson, Sina Mostaghel, Theo Lehner

"Rönnskär smelter of Boliden Mineral AB, Sweden, is well known for recycling of base and precious metals. Slag from the electrical furnace is processed at the fuming plant to produce zinc clinker. The granulated slag is a by-product used as e.g. construction material. In this paper, influences of Al2O3 on mineralogy of the slag, which can affect its chemical and physical properties, are investigated. Different mixtures of Al2O3/fumed slag were prepared. Re-melting was carried out in a Thermo-Gravimetry (TG) furnace with an inert atmosphere. Scanning electron microscopy (SEM) and X-ray diffractometer (XRD) were then applied for the analyses. Investigations depict that addition of alumina to slag, results in an increase in the number of spinels and a transformation from iron rich to aluminum rich spinels. Anorthite (CaAl2Si2O8) will also be formed.IntroductionRönnskär smelter of Boliden Mineral AB is located in north of Sweden; the main products of this smelter are: Copper, Zinc clinker, Lead, Gold, and Silver, while sulphuric acid, liquid sulphuric dioxide, and Iron sand are some of the by-products. Reducing the energy consumption and decreasing the usage of finite natural resources are becoming more and more important for the Rönnskär smelter; this result in use of different recycling and scrap materials. Metal residues, from brass foundries, steel mills, and electronic scrap are recycled at Rönnskär smelter [1]. Most of the electronic scraps contain mixtures of various metals together with plastics and ceramics, which can affect the composition and properties of the slag considerably [2]. At the same time, treatment of slag and controlling its composition and properties are of much interest for Base Metals producers from different aspects. Composition of slag influences the physical properties such as: 1) Liquidus temperature [3-4] 2) Viscosity, which controls separation of valuable metals, especially copper by gravity separation [2] and also heat and mass transfer [5] 3) Electrical conductivity [6]."

Jan 1, 2008

Foamed cement packs offer a viable alternative to conventional timber or other forms of packs for permanent underground support. These packs comprise steel mesh and hoop containment with an outer bag for the grout; woven, laminated polypropylene fabric being ideal for the purpose. The grout is supplied in 25kg bags and fed into a purpose ? designed foam placer machine which delivers the foamed grout directly to the packs from 60 metre long delivery hose. Foamed cement grout as a fill material offers attractive properties for support packs, in summary these are: Variable Grout Strength Grout strength is controlled by the grout density being delivered from the placer machine. This can be changed by the machine settings. Strength Development Fast rate of strength development is possible so that support is available quickly. Pack yield The foamed grouts are compressible so that yielding of the grout pack can be achieved without loss of support. Rate of Filling Three sizes of placer machine are available, these use one, two, or three 25kg bags per minute of grout, pack filling time is therefore a matter of minutes, a typical 0.75m diameter pack x 1.2m high taking some 17 minutes to fill. Tests in a 1000 tonne press have confirmed that the above characteristics can be achieved with foamed cement packs at acceptable cost. This will be illustrated in the paper with experience to date.

Jan 1, 2008

Conventional blasthole sampling for grade control has acquired an extremely bad reputation for the last 50 years. The introduction of many sources of bias is a structural reality. Delimitation biases are devastating. Extraction biases are of great concern as well. Weighting biases aggravate an already bad situation. Furthermore, preparation biases are many. Some of these biases are due to the type of drilling machine that is used and are nearly unsolvable. Some of these biases are due to the sampling tools that are used and often unsatisfactory. Attempts to automate blasthole sampling at the drilling site have failed, not because it cannot be done, but mainly because it interferes with drilling productivity. As a result the miner most often rejects the idea after a few weeks of practice. Manual sampling of blasthole piles is a disaster for many reasons; some are related to the methodology, some to the selected sampling protocol, some to the training of operators, some to limited manpower available, and some to limited supervision. Furthermore, with blasthole sampling a time logistic problem is unsolvable as the miner wants the ore grade control geologist to make up his mind within two or three days at most; as a result not enough time is allowed for samplers, preparation facilities, laboratory, and resources department to perform a good job as everyone is working under unreasonable pressure. The economic impact of poor blasthole sampling for grade control has been vastly underestimated by mining companies. The resulting ore grade misclassification is responsible for severe reconciliation problems and massive financial losses every year. This paper suggests areas along this grim scenario where things can be greatly improved; however it is clear that too many problems are unsolvable. An alternative using reverse circulation drilling for grade control is suggested. A thorough analysis of the respective advantages and disadvantages for blasthole and reverse circulation drilling for grade control is presented in this paper.

Jan 1, 2008

By Felipe P. D. Lopes, Jr. dos Santos, Sergio N. Monteiro, Frederico M. Margem

"Natural fibers are gaining attention as a class of low cost, biodegradable and renewable materials that also exhibit some interesting properties for specific applications. In particular, the incorporation of some natural fibers in polymeric matrix composites is nowadays providing opportunity of manufacturing a variety of industrial items, for instance automobile interior components. Among these fibers, ramie (Boehmeria nivea) is one of the least investigated and only recently was studied as polymeric composite reinforcement. Therefore, the objective of this work was to evaluate the possibility of ramie waste reinforced polyester composites to replace conventional building materials, such as plywood, plastic boards and gypsum panels in terms of a cost-benefit analysis.IntroductionThere is a growing concern over the environmental questions that are presently affecting our society in a global sale such as climate changes and generalized pollution. Among the solutions for these questions, the replacement of energy intensive materials, especially those long term degradable such as the synthetic fibers, is already being considered [1]. As a consequence, the past decades have witnessed an increase in research devoted to new biodegradable materials obtained from natural resources mainly the biomass. Important examples are the renewable natural fibers as well as composites incorporated with them [2,3]. In addition to their friendly status with respect to the environment, well know natural fibers like jute, sisal, wood, coir, hemp and flax are relatively low cost and recyclable. In recent works [4,5], the use of these cultivated and abundant lignocellulosic fibers was investigated as the reinforcement phase in polymeric composites.Other less know lignocellulosic fibers have also been recently investigated [6,7]. These are fibers that likewise show a potential of incorporation into the polymeric matrix of composite materials. Most of these less know fibers are typical of tropical regions and, in principle, their application in industrialized composites would represent job opportunities for developing countries in Africa, South Asia and Latin America."

Jan 1, 2008