Search Documents

By Carlos A. Ferreira, Betina Hansen, Marco A. S. Rodrigues, Marcela P. Proença

"Nowadays, the concern with the reduction of industrial pollution has motivated researchers to found out new technologies for treatment of industrial waste. The clean technologies, as electrodialysis, are capable of treating these residues, minimizing the impacts when they are discarded directly on the environment. Membranes of SPS/HIPS, PAniCSA/SPS/HIPS, SPAN/SPS/HIPS were developed using chemical mixture method. Membranes were characterized by Infrared Spectroscopy (FTIR), Thermogravimetric Analysis (TGA), Dynamic Mechanical Analysis (DMA) and Scanning Electronic Microscopy (SEM). Membranes were submitted to electrical polarization and to electrodialysis at NaCl and KCl solutions, in order to determine ionic transport through the membranes. Results were compared with commercial membranes. The average percent extraction for Na+ ions obtained by membrane was beyond 20%.IntroductionThe high environmental impact caused by the galvanoplastic industries represents today a world concern(1). In the galvanoplasty, thin metallic layers are deposited on metallic surfaces(2) through chemical methods or electrochemical process. This industrial process presents some disadvantages that limit its utilization, as the generation of toxic effluents containing concentrations of heavy metals usually above the limits allowed for his release in receiving bodies(1), the production of galvanic sludge which is considered hazardous waste and that is very difficult to treat, beyond the high consumption of water (3).Stimulated by the development of new ion-exchanged membranes with high selectivity, lower electrical resistance, and improved thermal, chemical and mechanical properties, the use of electrodialysis in the wastewater treatment has recently gained a broader interest(5). The electrodialysis (ED) is a mass separation process in which electrically charged membranes and an electrical potential difference are used to separate ionic species from an aqueous solution(5). The technique permits the recovery and the reutilization of the waste products from the industrial process, avoiding the discharge of them on the environmental (acting as clean technology)."

Jan 1, 2008

By Ning Wang, Bing Xie, Hong-Yi Li

"Compared to traditional sodium roasting, calcified roast inhibits chlorine pollution. A vanadium extraction technique based on a calcified roast is especially suitable for vanadium slag with high calcium content. In this report, V205was extracted from vanadium slag by calcified roast followed by acid leaching and hydrolysis precipitation. In optimized conditions, the high silicon low vanadium slag was roasted at 850'C for 2 hours without CaO addition. The roasted materials were leached with 35 % H2SO4 in liquid/solid ratio of 5:1 (mL/g) at 95OC for 4 hours. The extraction of vanadium was as high as 97.66 %. These results are instructive to V2O5 production in industry.IntroductionVanadium slag is produced in converter, sodium salt roasting is the commonly used technique to extract vanadium. In sodium salt roasting, vanadium slag is roasted with sodium salts including sodium chloride and soda as additives, followed by leaching with acidic or basic solution [1]. However, in this process chloride reacts to produce corrosive gases including HC1 andCl2- SO2 and SO3 can also corrode equipment severely and are also an environmental contaminant. The low melting point of sodium salts leads to fusion agglomeration, which blocks vanadium oxidation and thus decreases the extraction rate of vanadium. A large amount of sodium salts consumed as roasting additives increases the production cost. Moreover, sodium salt roasting requires low CaO content in vanadium slag. When the CaO content increases to 1%, V2O5 extraction can amount to 4.7%-9% [2]. For vanadium slag with high CaO content, the sodium salt roasting technique leads to low vanadium extraction rate."

Jan 1, 2012

By Viviane Tavares de Moraes, Denise Crocce Romano Espinosa, Jorge Alberto Soares Tenorio, Adriana Johanny Murcia Santanilla

"Increasing volumes of solid waste are generated worldwide, due to the continuous technological advances, the electronic scrap is part of these waste, requiring the study of recycling processes to stimulate this activity or the reuse of its components. The separation of nickel from sulphate leach solution, which also containing iron, zinc and aluminium was carried out using bis-(2,4,4-trimethylpentyl) phosphinic acid (Cyanex 272) as extractant, in order to determinate the effects of pH and temperature. The number of stages required for extraction was also assessed. The results showed that the metal extraction increased with increasing pH. On the other hand, increasing temperature was not favorable for all metals. However, under conditions used in this paper the purification of solution containing nickel was possible.IntroductionIncrease in the demand of metals in the world for use in industry causes a great exploration of natural resources. One outcome of this is increased investigations for the recovery of metals from industrial wastes. Nickel is found in wastes, such as batteries and electric and electronic devices, this kind of waste becomes a significant source for metals recovery. Since nickel is also present in printed circuit boards, which are associated with electric and electronic equipment, it can be recovered from this kind of waste through different techniques. It is important to highlight that iron is generally associated with this scrap [1] and for its removal chemical precipitation is often used. On the other hand, the solvent extraction process is widely used for treatment of leach liquors, because it can be produce high purity solutions [2, 3]. This technique is based on the purification of solution using contact between a liquor leaching and the immiscible organic solution, which contains an extractant that promotes the desired metal transfer [4]."

Jan 1, 2012

By Rauno Peippo

Horizontal Waste Heat Boiler (WHB), today's proven and dominating technology for copper smelter gas cooling, has been utilized by the industry for over half a century. During this time development has taken place in geometry, flow characteristics, cleaning technology and design details. This development has been driven by improved understanding of the specific process requirements, gained both by wide experience and by utilizing new emerging design tools, like computer flow modeling. It had to wait till mid 90's to unite effective and proven Spring Hammer cleaning technology and the process benefits gained by gas guiding vanes or baffle wall in the copper smelter WHB design. The new design has demonstrated improvement in gas cooling efficiency and the process conditions down stream in form of less dust sticking problems in the boiler and precipitators. Reduced weak acid production has also been reported as a result of the design. The theoretical aspects, computer flow modeling results and actual benefits measured in old smelting line modernization are discussed. Experience £tom modernization projects such as Phelps Dodge, Atlantic Copper, Mexicana de Cobre, and Nippon Mining, Saganoseki, are discussed. In mechanical design there has been development resulting improved gas tightness with less corrosion and better control of dust sulfation. An essential improvement is the integration of the boiler hopper and dust removing conveyor. Having no steel plate casings in the hopper and conveyor section but using of boiler tube membrane instead eliminates thermal expansion differences. The dust conveyor will be effectively cooled against hot dust lumps falling down while the acid dew point corrosion is prevented in the cooler sections of the hopper. Conceptual features are presented of a new generation Copper Flash Smelter WHB presently under construction at Boliden Mineral, Skelleftehamn, Sweden, where the latest development and innovations are adopted.

Jan 1, 1999

By Robert Kozicki, Eric Graham, George Wrightson

"IntroductionThe manufacture of Ferro Chromium involves the smelting of various ores and fluxes to produce the metallic product.Slag is inherent in the process. It has a much lower density than the metallic FeCr. Some chrome may be trapped in the slag as either FeCr or Cr203.Previous methods to estimate the slag in the FeCr have revolved around separating the slag and metallic portions by exploiting the differences in density. The downside with that procedure is that material will often contain pieces that are adhered FeCr and slag. The Metallic FeCr may also be completely encapsulated in the slag.An alternative and more precise method involves calculating the slag content based on chemical analysis of Mg and Al. The Mg and Al will be at relatively low levels (less than 0.1 % ) in the Metallic FeCr pieces and considerably higher in the slag (3% or greater). The overall sample will have a proportional amount and is calculated using simultaneous equations with the assumption there is only one kind of slag and one kind ofFeCr present. ""Pure"" slag and ""pure"" FeCr are needed in order to determine the Mg and Al in each. The detemlination of the Mg and Al in the overall sample would then be used to calculate the amount of slag.When the particle size is small, it is difficult to sample and get ""pure"" pieces of the slag and FeCr of sufficient quantity to perform a proper analysis. Often, historic data is used but that is dependent on the source of the FeCr and the materials used in its production. Mg and Al levels in slag can vary between 3% and 20% in different FeCr slags depending on their origin."

Jan 1, 2013

By Wellington Pereira Inácio, Frederico Muylaert Margem, Artur Camposo Pereira, Sergio Neves

"Natural fibers are currently gaining attention as reinforcement of polymer composites for uses in engineering parts for automobile and building construction. In spite of environmental, economical and societal advantages, the natural lignocellulosic fibers are not as uniform in their dimension and properties as compared to synthetic. In recent works it was found that the variation in strength could be correlate to the equivalent diameters for several lignocellulosic fibers including the sisal fibers. In the present work an investigation on a possible correlation of the equivalent diameter with changes in density and elastic modulus was carried out. Precise measurements of the equivalent diameter, conducted in a profile projector, were correlated with the density and the elastic modulus by means of the Weibull statistic analysis. The results showed that an inverse correlation with the diameter also applies for both the density and the elastic modulus with a high degree of precision. SEM observation of the sisal fiber in structure and fracture aspects strongly indicate that defects and microfibril participation could be responsible for the inverse correlation.IntroductionAccording to Kalia [1], cellulose-based fibers are currently being pushed owing to their ""green"" image. Contrary to synthetic glass fiber, extensively used in our modem technology, these lignocellulosic fibers are renewable and can be incinerated at the end of the material's lifetime without adding pollution in the atmosphere moreover, the amount of CO2 released during incineration process is negligible as compared to the corresponding amount taken up by the plant throughout its lifetime. Even if an industrial processing equivalent of C02 release is added, the lignocellulosic fiber is considered neutral with respect to the emission of gases responsible for the global warming [2]."

Jan 1, 2012

By Gaifeng Xue, Jingxuan Zhou, Shangchao Liu

"Both COD and TOC can characterize organic pollution of coking wastewater. In theory, there is a linear correlation between these two indicators. After continuous monitoring TOC and COD of coking waste water, linear regression relationship between of these to indicators was studied with the use of mathematical statistics. And conversion equation between these two indicators was established, and using t-test method for significance testing. The results showed that the linear relationship of COD and TOC was significant. Also interval estimation of equation slope and intercept were given in the condition of 95% confidence level. A linear regression equation established can be used to indirectly convert TOC to COD with high precision and accuracy.IntroductionBoth chemical oxygen demand (COD) and total organic carbon (TOC) are measure of the degree of characterization for organic pollution of water bodies. The current COD standard analytical methods is Potassium dichromate titration method [1] . there are some disadvantages in this method, such as only part of organic matter in the water bodies being oxidated, the refluxed steps, a long time needed for each measurement, high cost. It is the most important that sulfuric acid silver and mercury sulfate reagents used in the measurement may easily lead to secondary pollution. In contrast, the measurement of TOC is by the method of combustion or Photocatalytic Oxidation. The result could be easily got from the instrument. There are some advantages in this way, such as easy operation, short time and little expenses for each measurement and no secondary pollution 121• In addition, the measurement of TOC has higher degree of precision and accuracy than the measurement of COD both in the determination of calibration standards and actual samples. The meaning and contrast of TOC and COD are listed in the table 1."

Jan 1, 2013

By Chenhui Liu, Ka-ma Huang, Hong-ying Xia, Bingguo Liu, Hua Chen, Jinhui Peng, Libo Zhang

"The rising popularity of microwave heating in mineral processing has fuelled the need for knowledge concerning dielectric properties of minerals. Dielectric property and microwave absorption property of anthracite were measured over a temperature range of 20-100°C at 2.45GHz by using an open-ended coaxial sensor measurement system. The results show that the dielectric constant, loss factor and loss tangent increase with temperature rising at 2.45GHz. Microwave absorption properties of anthracite are highly dependent on temperature and frequency. At frequency of 2.45GHz frequency used in microwave metallurgy, anthracite is suitable for reducing agent to achieve fast elevation of temperature then returning to original state. The research will be helpful in explaining the thermal running of microwave dielectric heating the anthracite.IntroductionThe application of microwave heating in minerals processing and treatment has recently attracted great interest from the metallurgical industry. Compared with conventional heating methods, the advantages of microwave heating include rapid and selective heating, uniform distribution, high efficiency, fast on and off switching as well as flexible and modular design[l-3]. As a result of these advantages, microwave heating has been applied in a variety of mineral processing and extractive metallurgy, such as microwave-assisted ore grinding, microwave heating for carbothermic reduction and acid leaching of ilmenite ore, microwave drying, microwave-assisted roasting and smelting of sulfide concentrate, microwave-assisted spent carbon regeneration and microwave-assisted waste management [ 4-6]. Though the application of microwave heating in the metallurgical industry is promising, further studies on the interaction between microwave radiation and minerals and its effects are highly desired to develop innovative techniques for minerals processing and ore treatment using microwave heating [7]."

Jan 1, 2013

By Artur Camposo, Rômulo. L. Loiola, Frederico M. Margem

"The growing interest for natural materials as an environmentally friendly alternative for the substitution of energy intensive and non-sustainable synthetic materials, has motivated the use of lignocellulosic fibers as reinforcement of biocomposites. The sisal fiber, a relatively unknown lignocellulosic fiber with potential for composite reinforcement, still needs to characterize for possible engineer applications. Therefore, the present work analyzed the sisal fiber by means of Fourier Transform Infra-red (FTIR) spectroscopy. The sisal fiber FTIR spectrum revealed main absorption bands typical of any lignocellulosic fiber. However, some specific bands as well as bands broadening and intensity suggested particular activities for functional molecular groups in the sisal fiber.IntroductionIn recent decades, environmental issues related to worldwide pollution and climate changes, mainly the global warming, are motivating new paradigms for the development of our society. Among these, the use of natural materials in substitution for non-sustainable synthetic materials, obtained from non-renewable ores and petroleum, is increasingly being considered. In particular, natural fibers extracted from plants are, in this 21st century, experiencing a surge as composite reinforcement [1-11 ], following their replacement by synthetic fibers, specially the glass fiber, during the second half of the 20th century [1-2-8].In addition to environmental benefits [12-13] the lignocellulosic fibers present economical advantages, such as worldwide abundance and comparatively low costs as well as some technical properties associated with flexibility and toughness[ll], which contribute to the performance of automobile components fabricated with natural fibers composites[14-16].Among the less common lignocellulosic fibers that only recently have been investigated[l 7], the fibers extracted from the stem of the sisal plant, shows in Fig 1, reveals a potential for polymer composite reinforcement."

Jan 1, 2013

By Anne C. Chinellato, Alejandra T. Soria, Nelida L. del Mastro, Amanda C. S. Pereiral, Esperidiana A. B. Moura, Anibal V. Abreu

"This work presents a comparative study of the thermo-mechanical and morphological properties of sugarcane bagasse fiber/HDPE composite treated with electron-beam and gamma radiation. The composite samples obtained by extrusion and injection molding processes were irradiated at 50 and 90 kGy using either a 1.5 MeV electron beam accelerator or gamma irradiator EMI-9, at room temperature in presence of air. The irradiated and non-irradiated samples were submitted to mechanical and MPI tests, differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), scanning electron microscopy (SEM), sol-gel analysis and X-Rays Diffraction (XRD) and the correlation between their properties was discussed. Improvement of the bagasse fiber/HDPE composite properties, using electron-beam or gamma radiation, was found.IntroductionResidues of sugarcane bagasse fiber are widely produced in Latin America and other countries: in Southern Africa, Egypt, South-Eastern Asia, India, China, Australia, Cuba, among other producers, as by-products of the sugar and bioethanol industry. The sugarcane industry in Brazil and Uruguay is well established and expanding with large potential to increase the production of sugarcane bagasse in the next years [1-3]. Although the major portion of the bagasse is currently burnt for energy supply in the sugarcane industry, the disposal of this byproduct is still inefficient and, consequently, it is critical for agricu1ture profitability and environmental protection. Sugarcane bagasse is a lignocellu1ose fiber mainly constituted by around 46 % cellu1ose, containing hemicellu1ose, lignin, fat and waxes, silica and other elements [3, 4]. Studies have reported that sugarcane bagasse can be used to produce thermoplastic polymeric composites with excellent properties for many applications. [5-8]. Based on this survey, the transformation of bagasse into high quality industrial products, such as bagasse-polymer composites, can provide its more effective utilization."

Jan 1, 2012

By M. M. Sadawy

"The increased rate of exploitation of iron ores has resulted in a rapid depletion of high-grade iron ore deposits in Egypt. New iron reserves have to be discovered to secure the iron ore for steel production. This paper aims to study the characterization and magnetic separation of low grade Aswan iron ore. The results showed that Aswan iron ore is composed of oolitic hematite, goethite, quartz and kaolinite. The screen analysis indicated that Aswan iron ore had a uniform distribution of iron and silica in the different particle size fractions and there is no any particle size has high amount of iron or low content of silica. On the other hand the results of dry high intensity magnetic separation illustrated that this technique is not suitable for upgrading this ore.IntroductionIron is one of the common metals used in industry, as well as being the fundamental raw material used in iron-steel industry; products are wide spread even in daily uses. The total iron ore reserves of the world have been estimated as 3 70 billion tones; 160 billion tones is classified as economical, while 210 billion tones as potentially economical [1]. An estimated 98% of the iron ore exploited in the world is used in the manufacture of pig iron and steel, which are non-substitutable backbones of modem society. The rapid increase of world steel production over the last few years have required an equal increase in iron ore production, from 876.8 Mt in 2006 to 948.1 Mt in 2007 [2]. The increased rate of exploitation of iron ores has resulted in a rapid depletion of known high-grade iron ore deposits. This, in turn, has led to a dramatic increase of prices. In the absence of any major new discoveries of high-grade iron ore deposits, mining companies have turned to lower-grade materials to assess their beneficiation potential to expand their production base and beneficiation capacity, in order to satisfy future demand. Egypt is going to face shortage in iron production, consequently new iron reserves have to be discovered to secure the iron needed for the country [3]. Exploitation of low grade ores requires special equipments and techniques for recovery of minerals values. High gradient magnetic separators offer promise and great potential of application both technologically and economically in the processing of fine particles containing weakly or feebly paramagnetic components [4-6]. Within this existing framework, this research was initiated to assess the beneficiation potential of low-grade Aswan iron ore by high intensity magnetic separation."

Jan 1, 2013

By A. R. G. Azevedo, G. C. Xavier

"This work has for objective to identify the soil of the neighborhood Codin located in a lacking area of the urban nucleus of the district of Campos dos Goytacazes - RJ, after the identification the best line was determined for the production of soil-cement blocks. In this area it happens habitational deficit and precarious constructions are also verified. The use of soil cement blocks is considered a cheaper constructive method than the conventional (ceramic block or of concrete), because one of the components of the raw material is abundant (the soil) and the constructions can be erect with certain easiness for collective effort regime. Samples of soil of this area were collected for they be characterized with relationship to the physical and chemical characteristics, with I aid of GPS the community's location it was registered. Identified the soil type, the work began the study of lines they to make possible your use in an economical and safe way. For that were made drained blocks in the format 19,5x10x5 cm, with lines containing the addition of 5% and 10% of cement in volume, and as parameter of quality the absorption of water and the resistance to the compression were measured, following the Norms of ABNT.IntroductionWe know that the use of the soil by the humanity come from the antiquity. And ifs confirmed by the archaeology places of the old civilizations of the word. The most remote constructions date from 10.000 years old in Jericoh, in the Jordan River Valley. This work became more intensive at 3.000 B.C. (Before Christ), by people who lived in those valleys with mood areas, a lot of clay and washed by the rivers.Almost all the sectors of engineering of soils choose the stability to use the local soil. Although, artificially treated, offers more economical advantages.The stability of a soil consist of endow it of the condition to resist the deformations and ruptures during the period that it is being used, because these characteristics are necessary in any construction.The application of the natural soil only is possible in places that they are of good quality and attend to the requirements of engineering to the type of previewed application. The granulemeter correction and the chemical stability include cases of inappropriate soils areas, turning the soil able to be used as construction material. Among the stability agents, usually added to the soil for stability ends, the cement is indicated."

Jan 1, 2013

By Chi Ru?an

Sollutions of ammonium chloride, nitrate and sulfate were studied in extraction of rare earths absorbed on a low-grade, kaolilnitic ore recently discovered in southern China. The results of percolation leaching tests and the recovery of the rare-earth values from these solutions are presented.

Jan 1, 1989

By T. Goda, H. Kiuchi, M. Iguchi

"IntroductionThe utilization of silver in the electronic industry has been increasing in recent years. It is desirable that valuable metals are recovered from the used scraps of these industrial goods. Condensor chips, for example, contain silver, palladium, and Ag-Pd alloy. The dissolution behavior of silver was studied assuming that scraps such as used condensor chips in which Ag-Pd paste is used are subjected to wet treatment.ExperimentalIn this study the powder, granules, and flakes of silver were used in these nitric acid leaching experiments. The nitric acid solution was agitated in a glass reactor with a magnetic stirrer and heated to the required temperature. The experiment was started by putting the silver sample in the solution. After the leaching, the solution was filtered and the concentration of silver in the filtrate was analyzed by ICP.ResultsIn dilute nitric acid of less than 5 N, silver powder dissolved easily with increase in the concentration of nitric acid and temperature. However, the more intensive the stirring of the solution was, the lower the dissolution quantity became. Fig. 1"

Jan 1, 2000

By K. A. Elbarawy

Processing of Egyptian barite ore with a composition of 85.5% BaSO4; 2.75%SiO2;1.56%Fe2O3 and 5.1% Al2O3 was performed with the aim to prepare pure barium salts. The process took place through pelletization-solid state reduction and leaching steps. Each of these steps was optimized. Pure barium sulphate (99% < 0.82µm) and carbonate (99%<0.75µm )were the final products. This article deals with the reduction process that occur whn coal was added to the ore during pelletization in the ratio of 5:1 stoichiometry. Optimum reduction of pellets of 8-12mm in diameter was achieved after 60 minutes at 1050oC and under a rate of 5 lmin-1 of nitrogen atmosphere, where 87.79% of the ore was reduced. The kinetic studies showed that the reduction process could be modeled according to the core mechanism of diffusion control in which the effective diffusivity is based on the surface area of unreacted ore. The activation energy calculated was 92.7 kJmol-1.

Jan 1, 2006

By James D. Navratil

The mineral magnetite, or synthetically prepared iron ferrite (FeO?Fe2O3), has been used to separate a wide variety of substances, such as dissolved metal species and particulate matter, from wastewater. In the absence of an external magnetic field, activated magnetite readily adsorbs numerous metal species including actinide elements. In the presence of the external magnetic field, enhanced capacity was observed in using supported magnetite for removal of actinides and heavy metals from wastewater. The enhanced capacity is primarily due to magnetic filtration of colloidal and submicron particles along with some complex and ion exchange sorption mechanisms. The removal of the magnetic field and use of a regenerating solution can easily regenerate the loaded magnetite. The process has recently been tested for the removal of other metal ions including cobalt and iron. This paper will review previous work on the use of iron oxides for wastewater treatment and discuss the development and potential of the magnetic filtration/sorption process for wastewater treatment applications in hydrometallurgy.

Jan 1, 2003

By Leszek Blacha

Since several years aog there is noted an increasing importance of the metallurgical vacuum technologies. This refers mainly to the extra furnace steel treatment processes, melting of steel and special alloys in the induction and arc vacuum furnaces, as well as refining processes of nonferrous metals. In the presented work, there is discussed a phenomenon of evaporation of volatile components of metal bath under reduced pressure with description of kinetics of this process. In this article are presented are the evaluation of the mass transfer coefficients in the melt and gaseous phase. Based on results of our own research on removal rate of impurities from liquid copper (bismuth, lead) in vacuum refining process, it is determined the thickness of hypothetical boundary layer in the gas phase. This allowed to formulate a general kinetic equation defining the evaporation rate of gaseous components from metal bath. The values of mass transfer coefficients determined from this equation were compared with experimental results by other authors working on the evaporation effect of melt components of metal alloys.

Jan 1, 2006

By D. J. Burkhardt

Newer copper SX/EW facilities often incorporate hot water heating for the cell feed electrolyte to obtain the necessary plating temperatures of 40 to 50°C. Heating is most necessary in oxide heap leaching, however it may also be required in bioleaching of secondary sulphides in colder climates or higher altitudes where most of the heat gain in the heap is lost to the environment. Given that the solution flows in the leach, organic circuit and electrolyte circuit are circular in nature, and the fact that the hot lean electrolyte is often exchanged with cooler rich electrolyte, it can be difficult to access the heating requirement for the cell feed. There are energy losses in piping, tankage, raffinate, and energy gains through the PLS and electrowinning process itself; some of these are significant and others are not. This paper discusses the overall heat balance, the relative significance of the various energy gains and losses, and describes a methodology to develop a heat balance to assist the engineer in sizing the heating equipment.

Jan 1, 2003

By Tom McCullough

The purpose of this paper is to discuss the implementation and results derived from installing oxy-fuel burners in a l80 ton copper reverbatory melting furnace. Specific results will be discussed in the areas of melt chemistry, furnace modifications, productivity, process enhancements, and the combustion system capabilities.

Jan 1, 1996

By Toshiyuki Hashida, Victor M. Lopez-Hirata

"Small-punch tests and determination of fracture toughness JIC were conducted at 4 and 77 K on new cryogenic JN1, JJ1 and JK2 austenitic stainless steels, after isothermal aging. Equivalent fracture strain ?qf determined by measuring the reduction of thickness in the small-punch test specimen. A linear dependence of JIC on ?qf was found in these new materials. Regression analysis of experimental data produced the following linear relation JIC = 1304.1 ?qf + 8.09 [kJm-2]. An analysis of present work relation was pursued on the basis of material properties and evaluation method of he. Results showed that the slope value has a strong dependence on material yield strength and JIC evaluation method. This linear relation is useful for the evaluation of fracture toughness JIC, measuring the equivalent fracture strain ?qf by means of small-punch test. Thus it can be useful for assessing the degradation of fracture toughness in small areas such as, the heat-affected zone in welded components.IntroductionCryogenic structural materials for superconducting magnets of fusion nuclear reactor are required to possess a good combination of strength and toughness. The mechanical properties are required beyond the capability of conventional austenitic stainless steels [1]. New cryogenic JN1, JJ1 and JK2 austenitic stainless steels were developed by the Japan Atomic Energy Research Institute (JAERI) [1]. The structure of superconducting magnets is constructed by welding of 200 = thick plates of these steels, which are solution treated at high temperatures and then water-quenched to avoid intergranular precipitation. However, the welding process involves heating and cooling [2], which cause microstructural changes in both base metal and weld. In this heterogeneous microstructure, it is important to estimate the fracture toughness of these materials at cryogenic temperatures. Therefore, it is necessary to evaluate the effect of aging process on the fracture toughness behavior of these new steels. To determine the cryogenic fracture toughness, the elastic-plastic JIC value has been co=only used [2]; however, the specimen size is much larger than heat-affected zones in welded components. Small-punch (SP) testing method, employing miniature specimens, has permitted to evaluate the fracture toughness behavior at different temperatures in different nuclear reactor materials [3,4]. Mao et al. [5,6] and Misawa et al. [7] found a linear relation between JIC value and equivalent fracture strain ?qf, determined by SP method in non-ferrous alloys and ferritic steels at room temperature and austenitic stainless steels at 4 and 77 K, respectively. So that, this kind of correlation would be very useful to assess the fracture toughness JICe values by means of SP test in small zones of welded components."

Jan 1, 2012