Search Documents

By Ronald J. McGregor

An overview or precious metals project development and start-up, which emphasizes the process decision. Logic which determines process flowsheet, project economics, and training required to train new operators for start-up. The process decision required to successfully develop a precious metals project requires a blending of test data, environmental considerations and operations experience. Decisions to use Merrill-Crowe or carbon adsorption/ electrowinning/replating, fixed pad or multi-use pad {in heap leach) are dependent not only on technology but also on ability to train new operators. The market for experienced operators is acutely depleted and almost all new operators will have to be "home grown". Experience from the Brewer project in South Carolina as well as other projects put together in the West will be discussed.

Jan 1, 1989

By Maurizio Marezio Bertini

Successful treatment of contaminated sediments was achieved by sparging either 0.5 M NaOH solutions or distilled water with an SO2/O2 gas mixture. Metals such as Cu, Pb, Cr and Cd were successfully removed in a relatively short time. The effect of temperature and pH was investigated. Higher temperatures produced faster and higher recoveries with Pb and Cr more affected to temperature increase than Cu and Cd. The removal of copper, up to 50% percent, was achieved in alkaline solutions through the formation of copper sulfite complexes. The complete removal of metals such as Cu, Pb, Cr and Cd required that part of the treatment be carried out in acidic solutions. A preliminary cost analysis was carried out.

Jan 1, 2003

By P. T. Velu

Light weight aluminum alloys are the major construction materials for a number of structures in automobile and aerospace industries. Higher cost of production is the key impediment which restricts the usage of these alloys. A new electrochemical process route for the low cost production of aluminum alloys is being investigated, in which alloying elements are obtained from the dissolved compound. In the present investigation, solubility of lithium compound has been determined by measuring the EMF, when it is dissolved in the electrolyte. The solubility of Li2CO3 increased with temperature from 2.95 wt pct at 1063 K to 7.57 wt pct at 1093 K. Activities of the compound in the electrolyte were deduced using Temkin's ideal solution approach.

Jan 1, 1995

By M. R. Dahm

The demand for low sulfur steel by steel manufacturers and their customers has been steadily increasing for 25 years. Historically sulfur has been controlled by various means and with various additives but lime-magnesium external desulfurization of hot metal has become established as the dominant method in North America today. Magnesium powder produced from primary magnesium ingot has been the major source or raw material. However, periodic increases in the price of this commodity have encouraged producers to look to secondary magnesium for an alternate source of magnesium. Secondary magnesium from post-consumer scrap can be cleaned, sized, and prepared to produce a high quality magnesium reagent for use in hot metal desulfurization at a lower cost than material processed from primary ingot.

Jan 1, 2000

By V. Bhagavathy

This paper describes a method for the determination of traces of rare earths using energy dispersive x-ray fluorescence spectrometry (EDXRF) after preconcentration of their oxine complexes onto activated carbon. Various parameters that influence adsorptive preconcentration of rare earths onto activated carbon viz. pH, amounts of activated carbon and oxine, time of stirring and aqueous phase volume were systematically studied. A numerical method based on simple least square procedure using fifth order polynomial with 25 consecutive values was developed for smoothing and differentiation of EDXRF data which was previously digitized and averaged. First order derivative EDXRF in conjunction with adsorptive preconcentration on activated carbon enables to determine as low as 10 ppb of each of individual rare earth elements.

Jan 1, 1989

By F. M. Doyle, K. Sreenivasarao

Copper and cadmium metal has been recovered from dilute (3 X 10-4 mol/dm3 ) chloride solutions by ion flotation with dodecysulfate, followed by electrolysis. This approach should facilitate treatment of effluents too dilute for effective direct electrolysis. . The adsorption density of metal dodecylsulfate complexes on bubble surfaces was estimated from surface, tension data, and compared well with experimentally-observed metal removal kinetics, and ultimate recoveries. Copper and cadmium were recovered by electrolyzing the foamate, using steel wool cathodes and a graphite anode. The stability constants of the copper and cadmium dodecysulfate complexes are estimated, and used to analyze the thermodynamics of electrolysis. Dodecysulfate was unaffected by the electrolysis process, and hence could be recycled to ion flotation. A conceptual flowsheet for an overall effluent-treatment process is presented.

Jan 1, 1997

Aluminum has experienced significant growth in automotive applications over the last decade as a result of its properties and performance attributes. Looking to the future, the opportunities for continued growth in powertrain and suspension applications plus light weighting of body structures offer the potential for considerable further growth. This represents a growing "energy bank" of aluminum that will become available for recycling at the end of these vehicles' lives. Today, around 90% of the aluminum is recovered and recycled from scrapped vehicles because of its high value relative to other materials. The future growth offers opportunity for new technology and practices, to maximize scrap quality and recycling application. This paper will review the demand for these new technologies and practices and will discuss industry activities being pursued in this area.

Jan 1, 2000

By Elli Nurminen

Fouling of heat recovery process equipment may significantly decrease their heat transfer efficiency. In Copper Flash Smelting process flue dust tends to form build-ups on the heat recovery boiler walls. Thermal transportation properties of copper flash smelting flue dust and its components have been studied. The effects of porosity and temperature on thermal transportation properties have also been determined. The results indicate that dust and its components are effective thermal insulators and build-up layers on the boiler walls are likely to decrease greatly the heat transfer efficiency of the boiler. Decreasing dust layer porosity has a strong increasing effect on thermal conductivity and increasing temperature has a slight decreasing effect on thermal conductivity. The results may be used in CFD-modelling and optimisation of the process.

Jan 1, 2006

By Henk Dijkman

Existing metallurgical operations can be optimized by implementing engineered bioreactor systems in the process configuration. For instance, metals can be recovered safely and economically from process and waste streams using biogenic sulfide. This paper focuses upon possible applications of high rate biotechnology in metallurgy and mining. Metal recovery from liquid streams (process bleed streams, leach water, waste streams), integrated removal of (fugitive) SO2, treatment of acid blowdown and other options will be described. Practical examples are given. A large-scale application of biotechnology at Pasminco's Budel Zink refinery is described. Here, acid plant blowdown is treated together with electrolyte magnesium bleed. Concentrated zinc sulfide (10 tpd) is produced biologically, eliminating the production of gypsum and closing the refinery sulfur cycle. Recovery of metals from solution at Kovehute Pribram in the Czech Republic is the second practical example. In this case, H2S is produced on-site for metal removal from an alkaline slag dump leachate. At the Caribou mine in New Brunswick, Canada, acid mine drainage is treated with biogenic sulfide. This plant is situated upstream of a lime neutralization plant. As a result, reusable ZnS is produced, the volume of the sludge (gypsum and hydroxides) from the lime plant is reduced by 50%, the sludge is free of heavy metals and the final effluent concentration of heavy metals is in the ppb range. In the second phase of this project, metals will be recovered from stored tailings, resulting in significant revenues.

Jan 1, 2002

By San-chuan Tang, Wen Chen, Shun-ming Ning, Kan-ping Yu, Qiang Zhao, Xue-yong Xing

"A new type of desilication agent (PA-2) was selected by experiment based on the analysis of the characters of silica gel, and the influence of desilication type, desilication dosage, pH value, temperature and aging time on the desilicating effect was studied. The test results showed that on the conditions that pH was 2.0, temperature was 20""C, aging time was12 hours and the dosage of desilication agent was 0.23%, the desilication rate was higher than 93% in solution.IntroductionVanadium is an important strategic resources, which applies to steel industry and petrochemical industry. The main materials for vanadium product are steelmaking vanadium slag, stone coal and containing vanadium waste catalyst, etc. And stone coal is a low-grade carbonaceous silicified vanadium resource, which is unique material for vanadium extraction in China. Meanwhile, our stone coal reserves is No.l throughout the world.The silica acid solution containing vanadium is produced by acid leaching of raw stone coal or its roasted ore. The silica content of this solution is mostly high, besides, when pH is higher than 2 , the solution is unstable. Furthermore, it is very easy to generate gel substance with the increasing of pH value and standing time. 'Ibis silica gel is composed of colloidal particles with the size in 0.001 - 0.1 um. As a result, it is very hard even impossible for the following operation of solution."

Jan 1, 2013

By Rong Yang, Qijie Zhai, Wenbin Xia, Changjiang Song

"Tills paper focus on the influence of carbon content and cooling rate on the microstructure and phase formation of Fe-Mn-C alloys under near-rapid solidification. When manganese content is about 11wt.%, more s-martensite can be obtained with cooling rate increasing when carbon content is 0.14wt.%, the formed phase changed from a phase to y phase when 0.74wt.% carbon is added to the samples, and when carbon content up to 2.1wt.%, carbide can be obtained in the sample. A host of stacking fault, which attributes to the strain-induced martensite, can be observed in the sample. The microhardness increased with cooling rate increasing, and under the same cooling rate, the microhardness of samples with 0.14wt.% carbon is highest.IntroductionTo obtain high performance materials is eternal pursuit of material science research. Material scientists have explored many new ways to obtain high performance materials from long time ago. Rapid solidification is one of most popular ways to produce advanced materials by obtaining metastable phases, because it is widely known that the solidification of metals in metastable phases gives access to a whole range of materials with novel properties [1]. Furthermore, nowadays metastable materials have been extensively used in many fields, for example, many of our modem high performance materials such as steel products or aluminum alloys for aeronautical applications are in the form of metastable rather than stable phases [1]."

Jan 1, 2012

By Guanghua Wen, Jian Li, Mingmei Zhu, Fei Xiong, Shengjian Cao

"Small inclusions removal from molten steel in a continuous casting tundish by gas bubbles, which were generated in the turbulent flow region by introducing inert gas, was analyzed theoretically and the inclusion-bubble adhesion and flotation process was also observed by high-speed photo-graph in water model. Results showed that small inclusions in the range of 20-50µm removal from molten steel by bubbles flotation involves three stages: contact, adhesion and flotation. The inclusion-bubble adhesion processes include two ways: inclusions adhering to the upper part of the bubble and inclusions adhering to the lower part of the bubble. As the bubble floats up, the number of inclusions adhering to the bubble are increased. The proper size of bubbles, which could enhance small inclusions removal efficiency, should be controlled in the range of 1-2mm.IntroductionReducing inclusions content in molten steel is a very important way to improve quality of steel, and one of the main tasks in steel making process.A variety of methods have been used for inclusions removal in molten steel. At present, the main approaches to remove inclusions are gas stirring, slag cleaning, filtering, centrifugal separating, and by means of ultrasonic or electromagnetic field. Among these techniques, gas stirring is the most widely and effectively method for inclusions removal. Inclusions in molten steel will be aggregated and generated to form larger size inclusions, and subsequently floated to the surface of molten steel by buoyancy; meanwhile, some inclusions will be adhered to bubbles and floated together to metal-slag interface where inclusions are absorbed by the covering slag layer. Some research work showed that flow behaviors of small bubbles are different from that of big ones [1-2], and smaller bubbles are more efficiency for fine inclusions removal in molten steel.There are many methods to generate bubbles. During steelmaking process, highly turbulent flow in the ladle shroud can split introduced inert gas into small bubbles, which enhances the removal of fine inclusions from molten steel. Turbulent flow of molten steel injected into tundish from ladle shroud has a high speed and it is a strong turbulent area in continuous casting. The gas can be introduced into the shroud below the slide gate. The high turbulence flow would break up the gas into small gas bubbles. Fine inclusions will be easily adhered to small bubbles and subsequently floated to the surface of molten steel. Generation of small bubbles in ladle shroud have been studied in some literatures [3-4]. Some research have analyzed the fine inclusions removal with injecting gas from the ladle shroud by mathematical simulation, and the results show that the refining method can obviously improve the removal efficiency of fine inclusions in tundish [5-8]."

Jan 1, 2013

By Che Xin, Liu Tianlong, Bi Hongyun, Chen Lijia

"High-cycle fatigue experiments were conducted at 800°C in laboratory air for three ferrite stainless steels including 15CrNbTi, 15CrMoNbTi and 18CrNbTi, where the stress ratio of 0.l was adopted. The experimental results show that at 800°C, the fatigue limit of the 15CrMoNbTi steel is the highest, the fatigue limit of the 15CrNbTi steel is slightly lower than that of the 15CrMoNbTi steel, and the fatigue limit of the 18CrNbTi steel is the lowest. At the same maximum stress, the 15CrMoNbTi steel has longer fatigue lives than the 15CrNbTi steel in the low stress area, while the 18CrNbTi steel has the shortest fatigue life. In addition, the observations on the fracture surfaces of fatigue specimens reveal that the fatigue cracks initiate transgranularly at the free surface of the specimens and propagate in a transgranular mode.IntroductionIn modem automotive industry, the manufacturers have paid great efforts to clean exhaust gas and to improve fuel economy. It is thought an effective way to increase the temperature of combustion chamber in automotive engine. And thus, the manifold closed to the engine in automotive exhaust system can suffer high temperature up to approximately 1000°C. Because of their relatively low thermal expansion coefficient, high yield strength at elevated temperature and good fatigue resistance, ferrite stainless steels, especially added with alloying elements such as Mo, Nb and Ti, are increasingly used for automotive exhaust systems [1-3]. In fact, exhaust manifold operated under high frequency vibration and exposed to high temperature exhausting gas also requires good fatigue resistance at elevated temperature. Some studies on the high temperature fatigue characteristics of stainless steel have been documented. It has beeen found that the fatigue limit of four ferrite stainless steels including 409L, 436L, 429EM and 444 (18Cr- 2Mo) reduces significantly with increasing temperature [4, 5]. In the research concerning the effect of a-phase embrittlement on fatigue behavior in a high-chromium ferrite stainless steel, it is noted that the precipitation of brittle a-phase will reduce the crack initiation and growth resistances and result in a decrease in fatigue limit [6]. In this investigation, the high-cycle fatigue behavior of three ferrite stainless steels including 18CrNbTi, 15CrNbTi and 15CrMoNbTi at 800°C have been studied to address the mechanical aspect of high-cycle fatigue behavior for ferrite stainless steels and to provide the theoretical reference for the safe design of automotive exhaust system."

Jan 1, 2013

By Beatriz Ribeiro Nogueira, Vijaya Kumar Rangari, Esperidiana A. B. Moura, Anne Chinellat, Arifa Parveen, Angel Visentim Ortiz

"Composite consisting of ethylene vinyl alcohol (EVOH) with short piassava fibers were prepared by extrusion process and their thermal and morphological behavior were investigated. The EVOH reinforced with 5 and 10 % of pi as sa va (Attaleafunifera Mart) fiber particle, based on the percentage weight ratio (wt %), untreated and treated with a commercial silane coupling agent, were prepared and the influence of fiber loading and the effect of chemical treatment on their thermal and morphological behavior were evaluated by SEM, DSC and TG analyses. Melt flow index (MFI) of the composites have been determined to evaluate the effects of fiber reinforcement on dynamic viscoelastic melt of the EVOH. In addition, piassava fibers characterization by SEM, FTIR, and organic and inorganic composition have also been carried out. The SEM results of the composites showed surface micrographs without microvoids and a good distribution, dispersion and compatibility between the fillers and the EVOH matrix. Concerning the piassava fibers characterization, the results showed that piassava has higher lignin content than cellulose and hemicelluloses, and around 0.7 % of ash with 52 % of silica (Si02). This high concentration of silica is consistent with the SEM analysis of the fiber that showed a large amount of ""silica rings"" encrusted on their surface.IntroductionLately, great worldwide interest has arisen in developing new technologies that enable the use of products with less environmental impact. Effort has been put into seeking natural modifier applications, particularly regarding the use of natural fibers. Special attention has been given to the use of natural vegetable fibers, because of the huge variety of species available. Such vegetable fibers are usually referred to as lignocellulosic materials [1]. This work evaluated the effects of piassava (Attalea funifera Mart.) fiber incorporation in an ethylene and vinyl alcohol copolymer (EVOH). The EVOH belongs to a family of copolymers with excellent gas barrier properties and resistance to organic compounds, which allow its application in different segments, from food packaging to gas tanks. However, EVOH is very sensitive to moisture, and in conditions of high humidity its gas barrier properties, thermal and mechanical properties are affected."

Jan 1, 2012

By Gowda H. S. Desai, A. Herbert Mervin, P. G. Mukunda

"The mechanical properties of cast iron depend on the graphite morphology and characteristics of metallic matrix. In spheroidal graphite iron these properties are affected by the nodule count, nodule percentage, nodularity, nodules per square mm, nodule types and size distribution. In this work an attempt is made to study of the effect of centrifugal and gravity casting process on the morphology and mechanical properties. A comparison of microstructure and mechanical properties of specimens of the cast are studied. It has been observed that the centrifugal effect produces an increase in rupture strain but hardness is unaffected. In microstructure it has been observed that the centrifugal effect produces an increase in the number of bigger nodules and decrease in the number of smaller nodules and an increase of nodules per square mm. It has no effect on nodularity percentage. The centrifugal casting process produces better mechanical properties.IntroductionCast iron, the first man-made composite, is at least 2500 years old. It remains the most important casting material, with over 70% of the total world tonnage [1,7]. The main reasons for cast irons longevity are its wide range of mechanical and physical properties coupled with its competitive price [l]. Gray cast iron is traditionally used in many industries because it is characterized by a flexibility of use, excellent castability, low cost, wide range of achievable mechanical properties. Gray cast irons are selected according to their tensile strength, high modulus of elasticity, good wear resistance and good machinability are desired and for this a high-strength cast iron is selected [2].Flake Graphite and Spheroidal Graphite irons are predominantly being used to manufacture heavy automobile components throughout the world. The properties of gray iron castings are much dependent on foundry practice. Perhaps the most interesting feature of the family of cast irons is the morphology of the graphite phase, which occurs as a result of changes in chemical composition, melting, melt handling techniques and the process of solidification and subsequent cooling. The significance of these differences through graphite morphology is observed primarily in their effect on the physical and mechanical properties of the iron, but in the foundries these are also known to influence the ability to manufacture sound and dependable castings."

Jan 1, 2013

By Bing Song, Fei Xi, Xuewei Lv, Kai Zhang

The electric arc furnace process is a common method to produce high TiO2 slag from ilmenite. The pre-reduction process was proposed in recent years in order to reduce electricity consumption. In order to enhance the pre-reduction degree, high energy ball milling was proposed to improve the specific surface area of the ilmenite prior to reduction. In this study, the carbothermic reduction behavior of milled ilmenite concentrate was investigated. It was found that the ball milling method can result in a higher reduction rate and improved metallization of iron. The metallization of iron increased with increasing the time of ball milling. The metallization of iron with milling reached 89.49% when the time of ball milling was 70 min., while the FeO content decreased with 70 min. of milling from 11.84% to 4.76%.

Jan 1, 2014

By Robert J. Stevenson

The chemical variation of central North American lignite fly ash can be compared using the major and minor oxide analyses and the distribution pattern of the inter-grain chemistries of the individual fly ash have been used to illustrate the variations in bulk ,sample and individual grain chemistry. This information documents the chemical variability of the lignite fly ashes by geographic region. There is a direct relationship between grains rich in SiOa and AlaO, and in the NazO content of the grains in lignite derived fly ashes. There is also a direct relationship between grains rich in Ca0 and the MgO and SO, content of the grains in lignite derived fly ashes,. These variations are shown using CaO-SiO2-Al2O3 and CaO-Na2O-MgO ternary diagrams.

Jan 1, 1992

By S. Suda

Hydrogen storage materials have been investigated for more than 30 years, particularly on metal hydrides. These materials are, however, considered today impractical because of their poor hydrogen capacity measured by mass density and their poor surface properties and characteristics against impurities. Recent R&D activities have been located in new categories of materials such as complex hydrides and chemical hydrides. Among these materials, NaAlH4 (one of alanates), Li-based complex hydride, and NaBH4 (SBH: sodium borohydride) are 3 major candidates as hydrogen storage materials. In the presentation, SBH as a non-reversible on-site but recyclable off-site is described in view of its practical availability as the source of H- (protide) applied for a new type of fuel cell named Direct Borohydride Fuel Cell (DBFC) and H2 (hydrogen) for Proton Exchange Membrane Fuel Cell (PEMFC).

Jan 1, 2006

By Doug Halbe

?Many are called, but few are chosen.? The biblical adage applies not only to life, but also to hydrometallurgical processes. There have been, in the past, many outstanding successes with new processes ? and also some dismal failures. What are the odds of success for a new process? When there have been problems, why? What can you do to make sure these problems don?t occur with your process? What effect will a slow startup have on project economics? How do financial institutions ? the people who loan your company money for the project ? feel about new processes and why? Is it possible to predict or estimate the time required to reach design parameters?and if so, how do you sell this estimate to management ? and financial institutions? Probably most important ? when do you start thinking about the answers to these questions?

Jan 1, 2003

Steel Ladle in Bhilai Steel Plant, SAIL, India, passes through VAD & LF-RH route and this exposes refractory lining to a severe operating conditions. Ladles are lined with in-house manufactured MgO-C refractories. Lining life used to be 35 heats, out of which 18-20 heats were through VAD/LF-RH, hence, ladle availability had become a constraint. Laboratory studies were carried-out to optimize granulometry and composition. Granulometry was developed by adopting Andearssen packing model. A suitable plasiticiser was identified to eliminate inconsistency caused due to variation in resin quality and weather condition. It reduced variation in green bulk density from 6 to 1.3%. Abrasion and slag erosion studies were conducted, which shows that with increase of carbon, abrasion resistance decreases and corrosion resistance improves. Based on these studies, graphite in slag zone was increased from 10 to 12.5% and in metal zone it was reduced to 7.5%. Different process parameters of brick making were optimized to make MgO-C bricks of maximum bulk density with reduced coke porosity. Modified bricks have bulk density of 2.99-3.02 g/cc and coke porosity of 9.5-10.5%. Further, shape of the bricks were changed from side arch to mini keys and thickness was increased from 80 to 100 mm. Mini key bricks are pressed from sides, thus eliminating variation in thickness which is critical dimension for dry joints. These modifications improved average lining life of steel ladles to 64 heats, which includes 37-40 secondary heats. Maximum life obtained is 87 heats.

Jan 1, 2006