Search Documents

By Orion Ciftja, Arjan Ciftja

"The directional solidification method is routinely used to produce polycrystalline silicon, an important material for the photovoltaic (PV) industry. The form of the solid-liquid interface during solidification has considerable influence on the material quality. The dissolved impurities and the solid inclusions above the solidification front affect the interface and may cause interface breakdown. We investigate the effects of pushing and engulfment of silicon carbide (SiC) particles by the solidification front during directional solidification of silicon. We employ a 12kg directional-crystallization furnace to cast the molten silicon. We use upgraded metallurgical grade silicon with low concentrations of metallic impurities (< 5ppm) and a high content of carbon (700 ppm) present as SiC particles. Samples from the cast polycrystalline silicon ingots are investigated by light microscope. The expected interaction of impurities with the solidification front is investigated theoretically using empirical models. The data obtained from the models are in good agreement with the experimental results.IntroductionDirectional solidification is a well-known method for producing multi-crystalline silicon for the PV industry. In this method a planar front, achieved during solidification, results in a clearly defined interface between the solid and the liquid phase. The solubility of major impurities is higher in the liquid than in the solid phase. Therefore, directional solidification will work as a purification process where the impurities are retained in the liquid phase [1]. Apart from the process of removing the dissolved elements in molten silicon, the directional solidification plays also another role. It will interact with the solid particles that may be present in the melt. When a liquid containing an insoluble particle is solidified, three distinct interaction phenomena are observed: engulfment of particles, continuous pushing, and entrapment [2]. The term “engulfment” is used to describe incorporation of a particle by a planar interface, and the term “entrapment” is used for particle incorporation by a cellular or dendritic interface (see Figure 1) [3]."

Jan 1, 2014

By Murray Johnston

New measurements have been made on the equilibrium distribution of selenium and tellurium between molten slag and metal phases. Distribution coefficients of Se and Te between magnesia-saturated calcium ferrite slag and copper or silver alloys were measured over the temperature range 1473 and 1673 K under controlled oxygen patrial pressures of 10-11 to 10-0.68atm. The results demonstrate that the minor elements are present in the calcium ferrite slag as the selenide (Se2-) and telluride (Te2-) respectively, up to a PO2 of 10-6 atm. As conditions become more oxidising, Te undergoes a transition to the divalent oxide whereas Se does not. Increasing the temperature was found to enhance partitioning of the minor elements to the slag. In terms of activities, at 1573 K, Se showed strong negative deviation from the ideal behaviour in the slag, while Te showed only slight positive deviation.

Jan 1, 2006

By Matthew D. Andriese, Jiann-Yang Hwang, Zhiwei Peng

"It has been demonstrated that metallic-bearing minerals are physically liberated from host rock when exposed to microwave (MW) energy. The metallic minerals are iron sulfides and spinel oxide minerals contained in peridotite rock. Experimental evidence has shown ore particles readily couple with MW energy at 2.45 GHz, 1000 W resulting in rapid heating. Thermal stresses are generated by highly absorbing metallic-bearing minerals resulting in cracking and embrittlement of ore particles that assists in crushing and grinding processes. The liberated metallic-bearing minerals are shown to report to coarser size fractions as a result of MW exposure.IntroductionComminution of ore material during beneficiation is a large energy expenditure for the mineral processing industry. Crushing and grinding operations alone consume 50-70% amount of energy used in mineral processing [1]. Size reduction becomes increasingly difficult with decreasing particle size making grinding the most energy-intensive step of comminution. The aim of comminution is to maximize liberation of economically valuable minerals from the host rock [2]. Overall, the less material that needs to be handled, then grinded, to create a useful product for hydro/pyro metallurgical processes will achieve the greatest reduction of energy.Much of the scientific interest for use of microwave (MW) energy in mineral processing has been for improved hydro/pyro metallurgical techniques [3-6]. Early authors have employed MW energy for improved grinding of ore particles but most conclude the energy savings do not justify the energy input [7-9]. The effectiveness of MW assisted grinding is dependent on the ore mineralogy and the absorptive properties of minerals contained within it. Ore containing magnetic minerals should prove successful with MW assisted breakage from highly absorptive properties."

Jan 1, 2012

By Pragna Bhakta

Newmont has investigated potential treatment options for low-grade refractory gold ores since 1988. After extensive R&D at Newmont?s laboratories, biooxidation pretreatment followed by ammonium thiosulfate leaching was selected for application to sulfidic preg robbing ores. A heap biooxidation and ammonium thiosulfate leaching demonstration facility was constructed in 1995 to conduct large-scale pilot tests at Newmont?s Carlin Operations. This paper presents Newmont?s experience with the recovery of gold from preg robbing ores using ammonium thiosulfate.

Jan 1, 2003

By Daojin Cao

Aiming at many controversial reports on Raman spectral pattern of octamolybdate ion in aqueous solution appearing in the literature, a new method for the establishment of corresponding relation between Raman spectral pattern and chemical components of aqueous molybdate solution was put forward using spectroscopy measure and component analyses of saturated solution of ammonium octamolybdate hydrate known structure. It was found that the main characteristic of Raman spectral pattern of the saturated solution was described as the same ?double-peaks, hereinto a weak peak at the boundary? as some literature, but chemical components of the saturated solution were affirmed to be octamolybdate ion (Mo8O264-) and double protonated heptamolybdate ion (H2Mo7O244-), which were in equilibrium in aqueous solution each other. The authors propose that the pattern of the saturated solution can be regarded as the standard pattern of primiparous octamolybdate ion during acidified molybdate solution. It is satisfying that the standard pattern is applied to the identification of primiparous octamolybdate ion during acidified molybdate solution.

Jan 1, 2006

By J. Peter, S. E. James, J. L. Watson

A survey of operating zinc smelters and refineries throughout the world has been done in conjunction with the Lead-Zinc 2000 Symposium. This survey follows the examples set by the Japanese Mining Industry Association in 1985 and 1995. Questionnaires were sent to operating zinc plants that covered feed materials, process details, energy consumption and labor requirements. The voluntary responses to the survey were tabulated. Key operating parameters including feed grade, production capacity, quality of the intermediate products and quality of the final products have been compared for both hydrometallurgical and pyrometallurgical processes.

Jan 1, 2000

By Dirk Bergmann

During the spray forming process, a continuous molten metal stream is atomized by impinging high speed inert gas jets. In the generated spray cone, the resulting metal droplets are rapidly cooled by the huge temperature difference to the surrounding gas phase and thereby partly solidified during flight. After a certain flight and residence time inside the spray cone, the droplets impinge onto the solid substrate and form the product (deposit) by compaction. Material properties of this preform strongly depend on several process parameters and especially on the thermal and kinetic state of the deposited droplets at the point of impingement. Smaller droplets may cool very fast due to their low mass and impinge onto the product in a completely solidified state as solid metal powder particles. Larger droplets with big mass contain a higher amount of thermal energy and impact during the state of phase change or still as completely liquid. It is obvious, that a certain amount of liquid content in the droplets is needed for forming a homogeneous deposit. Therefore, the thermal history of metal droplets during flight in the spray cone is of great importance for overall process modelling and control. Modelling the effects of the impinging droplet mass on the formation and heat balance of the deposit, the thermal conditions of the droplet stream need to be temporary and spatially averaged at different locations. Averaging may be achieved in different ways, giving alternative results. A first method is averaging over the droplets total enthalpy which consists of the thermal content and the remaining latent heat of fusion within the droplets. A second method may yield the average over the heat content and the solid fraction separately. Results of these two methods depend on the application and the kind of information which one wants to achieve and show some deviations, which will be discussed in terms of consolidation and energy conservation of the deposit.

Jan 1, 1999

By R. Y. Wan

Thiocyanate was evaluated for gold recovery from low-grade refractory gold ores following biooxidation for an acidic heap leaching approach. One of the important features in using thiocyanate is that the leaching can be performed in acidic media, thus avoiding problems related to neutralization and material handling as leaching with alkaline cyanide. Also, the acidic leaching enables the use of ferric ion or bioleach solution as oxidants. In this study, Newmont-Nevada low-grade refractory sulfidic ore was biooxidized in columns at a particle size of 100% passing 102 mm. Thiocyanate leach on the biooxidized ore sample was performed on both ground samples in pulps and coarse material in columns using ferric ion as an oxidant. The variables of thiocyanate and ferric ion concentrations were compared for effect on leaching. Thiocyanate leach results are encouraging and indicate potential for development of a practical process. Gold extractions by thiocyanate are comparable to cyanide leach. Thiocyanate consumption was higher than cyanide, but was in an acceptable level.

Jan 1, 2003

By ChuanJie Cai, Zemin Zhuang, Jing Chen, Xuebin Hao, Shaobo Zheng

"Carbon which was used as heating and reducing agent in traditional iron and steel making process at present brought us large amounts of greenhouse gas harmful gases and dust seriously leading to the fog and haze condition. As one of ideal global new energies, Hydrogen has good features such as rich resource, high heat efficiency, cleanness, renewable and transportation. With the commercialization of hydrogen energy, the world energy structure will be changed greatly. Although many scholars have done a lot of researches and long-term exploration on hydrogen metallurgy, researches on the formation of metal iron phase in the process of hydrogen reduction of iron oxides in slag was rarely reported, which had important theoretical significance on the development of hydrogen smelting reduction process. Based on the thermodynamics and kinetics calculation, A laboratory experiment has been designed to research the iron phase formation during hydrogen reduction of iron oxides in the molten slag in this paper. SEM and EDS techniques were also used to observe and analyze the iron morphology. According to detection results, the influence of temperature, reaction time and surface tension on the morphology of the iron phase reduced were showed.IntroductionWith the increasingly severe global warming greenhouse effect, governments are paying more attention to no-carbon and low-carbon energy development and utilization. Hydrogen has received widespread attention around the world, which has rich resources, high thermal efficiency, large energy density, use clean, transportation, storage, renewable etc [1].The development of the hydrogen economy is new competition areas of the world economy for the 21st century. China should assess the situation, and achieve the important strategy of peaceful development as the realization of new industrialization, by establishing a ""hydrogen economy"" industry revolution which replaces fossil energy. The current hydrogen metallurgy process includes hydrogen direct reduction, smelting reduction and direct steelmaking process. Hydrogen plasma hydrogen metallurgy is the use of hydrogen as a reducing agent to replace carbon reductant, to reduce carbon dioxide emissions, and to ensure the sustainable development of ironmaking industry."

Jan 1, 2014

By Kai Kang, Jun Bao, Shouping Liu, Xiao Sun

Powder characteristics have a significant influence on selective laser melting (SLM) process. In this research, particle size, surface contour and the microstructure of IN718 powder used in SLM were tested, and the physical and chemical changes during heating process of the powder were investigated as well. The shape characteristic and fluid properties of IN718 powder were defined and measured. It is shows that most particles of IN718 powder exhibited nearly spherical shapes, and the particle size is about 22.95μm. On this basis, IN718 sample was fabricated by SLM process using the powder and the microstructure of the fabricated sample was investigated. The results indicated that the sample has a dense microstructure, no macro-defects but a few micropores and porosity. Compared with the powder, there was no new phase formed in the sample and melting point of the sample was little less than that of the powder.

Jan 1, 2015

By V. A. Shumsky, I. P. Polyakov, N. M. Ospanov, M. A. Lyamina, N. N. Ushakov

Studies on the kinetics of the competitive processes of PbS volatilization and PbS oxidation, as applied to the heat and mass transfer conditions in the flame of the Kivcet furnace, revealed that the rate-determining factor is the supply of heat. Therefore, low yields of fume in the autogenous flash smelting of lead sulphide feeds are noted despite the high volatility of PbS at 1,300-1,400°C. Dust formation in the autogenous flash smelting of Kivcet-smelters does not exceed 5-7%, of which fumes amount to ~ 80%. Using extra fuel during autogenous smelting involves the mismatch of the sulphide oxidation rate and the release of heat in the flame, and increases the fume yield. This is a major cause of the high dust formation in pilot plant trials. The analysis of dust formation in the Kivcet smelting of oxidized lead feeds in an industrialscale smelter shows an overall increase of dust formation (up to 10% of the feed), with fumes constituting ~ 80% of the dust. A pronounced increase of the zinc component of the fumes is also noted. Lead

Jan 1, 2000

By Julian Szekely

A review is given of the current metals processing operations, where electromagnetic forces play an important part in affecting the performance of the system. These include arc furnaces, plasmas, the Hall Cell, electromagnetic stirring and others. These considerations will be extended to discuss what new frontiers may be breached by the intelligent application of electromagnetic phenomena. The topics discussed will include magnetic flow control, levitation melting and cold crucible melting and refining.

Jan 1, 1988

By I. Barin, G. Eriksson, F. Sauert

Computer-aided calculations using data bases and program systems are more and more needed for the rational development and optirnization of high-temperature processes. The calculation of mass and energy fluxes between different process steps as well as the determination of the chemical equilibria will be discussed, giving examples from nonferrous metallurgy. The simulation of a waste-material treatment process including high-temperature combustion and gas-cleaning systems will also be demonstrated.

Jan 1, 1988

By Chang Wei, Zhigan Deng, Jiqiang Liao, Minting Li, Hongsheng Xu, Yan Song, Cunxiong Li, Xingbin Li

"Abstract: Direct ?otation of oxidized zinc-lead ore is characterized by recovery of zinc and lead only around 55% and 50%, respectively. Mineralogical analysis shows that the sample used in the present study is a carbonate hosted zinc-lead ore, with a zinc and lead carbonate content that accounts for 80.14% and 75.63% of the total minerals, respectively. The carbonate hosted zinc-lead ore was hydrothermally sulfidized with elemental sufur and the experimental data indicated that under the conditions employed up to 75% zinc and 82% lead sulfidation extent were achieved. As a result of pre-sulfidation followed by flotation, the recoveries of zinc and lead into flotation concentrate were over 90%. A flotation concentrate was obtained with 52% Zn and 37% Pb from the materials which was treated by sulfidation.IntroductionSulfide ores are the primary source of zinc and lead, and they are becoming depleted; thus, metallurgical investigators are interested in using abundant oxidized zinc-lead ore reserves. The high-grade zinc-lead oxidized ore, which normally has a zinc content higher than 15%, can be disposed of by acid leaching and electrolysis. However, the low-grade ore, which has a zinc content lower than 10%, is difficult to smelt with pyrometallurgy and hydrometallurgy, and the processes are very complicated and expensive in terms of production flow and energy consumption. Therefore, making the low-grade oxidized zinc-lead ore more beneficial has become more important in recent years. Flotation is the most common process, and the primary method of recovering zinc and lead from sulfide or oxide minerals. It is well known that there is a difference between sulfurized and oxidized minerals regarding their separation by flotation. Flotation of zinc and lead oxidized minerals is extremely complex because of the similarities in the physicochemical and surface chemistry of the constituent minerals. There are no known direct-acting collectors capable of producing single metal concentrates [1-3]."

Jan 1, 2012

By Rauf Hurman Eric

The high temperature liquid miscibility gap in the Ag-Ag2S pseudobinary portion of the Ag-S system has been redetermined by very carefully conducted equilibration-quenching experiments. Samples were contained in evacuated and sealed silica capsules. The stratified liquid phase compositions were obtained by chemical analysis. The miscibility gap extends from 14 to 32.3 atomic percent at the monotectic temperature of 906°C and closes at around 1320°C.Thermodynamic properties of the liquid solutions, including the limiting activity coefficient of sulfur in molten silver were expressed analytically by using the sub-regular solution model which proved to be in excellent agreement with the experimental findings.

Jan 1, 2006

By Chen Dong, Yuanling Gao, Jilai Xue, Jun Zhu, Luxing Feng

"Porous Ni-Ti alloy has many applications in a wide range of engineering areas. The porous NiTi alloys were prepared from Ti and Ni powders in sintering process under argon atmosphere. The major chemical compositions of the sintered Ni-Ti body were Ni Ti, Nh Ti4O and Nh Ti, respectively, the internal pore structures were characterized by image analysis technique, which were dependent on various processing parameters such as sintering temperature, amount of poreforming agent, forming pressure, etc. The results show that the porous alloy samples had the characteristics of uniform pore and high open porosity; pore-forming agent and sintering temperature are important factors in porous; pressure affected the sintered products' pore, by affecting the combination of alloy powder with pore-forming agent.IntroductionPorous Ni-Ti alloy materials exhibit not only excellent shape-memory and superelasticity, high yield strength and ductility, good corrosion resistance and biocompatibility, but also have low density, low stiffness, and high energy absorption rate due to their porous structures [1]. In recent years, these porous Ni-Ti alloys have found applications in a wide range of engineering areas, such as bone implants [2-4], impedance-matching connectors [5], energy-absorbing structures [6,7], separators [8] and actuators [9], etc.Pore characteristics can play very important role in determining of the performance of porous NiTi alloys. For example, when the alloys are used to repair or replace hard tissue implant material, the pore shape and size not only determine their mechanical properties, but also have great effect on the fluid transmission of human body. The pore characteristics can also influence the stressstrain behavior of the porous Ni-Ti alloy and, thus, strongly affect their mechanical properties, superelasticity, and fracture mechanisms [10].In this study, the Ni-Ti alloys with high porosity were prepared in a powder sintering process under argon gas. The pore characteristics were investigated using SEM, XRD and image analysis techniques, especially in association with the content of pore-forming agent, sintering temperature and compacting pressure."

Jan 1, 2011

By John O. Marsden

The past fifteen years have seen a number of important developments in copper hydrometallurgy, including the commercial application of biological heap leaching of secondary (chalcocite-dominant) copper ores, the commercial demonstration of chalcopyrite concentrate leaching technology using pressure leaching and biological processes, and the application of novel configurations of solution extraction circuits. Significant emphasis is now being placed on the development of effective stockpile leaching practices for primary ores (chalcopyrite and bornite-dominant mineralization). Some of these developments have been highly successful, and will pave the way for further development and commercialization. Others have been less successful. These developments are reviewed in the context of the metal price cycle and trends for the future are identified.

Jan 1, 2006

By Paykan Safe

The primary source of fugitive gas emissions in most copper smelters are the Peirce Smith converter operations. The modem trend is towards installation of secondary gas collection systems which are intended to collect fugitive gases from charging, standby, and skimming operations. These have been installed with varying degrees of success. Often, the major source of emissions from the converter area is leakage of process gas from the primary hoods when the converter is blowing. This gas is typically collected by the secondary system and discharged to atmosphere or scrubbed with an alkaline agent. Those smelters considering installation of secondary hoods or scrubbing of gases from secondary systems should first address the issue of gas leakage from the primary hoods. Improving the primary hood gas collection efficiency will often be more cost effective than installing secondary hooding. In the case of secondary gas scrubbing, it will significantly reduce the reagent consumption and operating cost of the scrubbing system. This paper examines the parameters that determine whether or not a primary hood will effectively collect process gases without leakage and demonstrates, using Computational Fluid Dynamics (CFD), the effects of variations in these parameters on the overall performance of the hood. It also looks at the application of CFD techniques in the design of secondary hoods and presents a summary of measured emissions from converter buildings.

Jan 1, 2002

By Takashi Miyamoto, Hideo Nakae, Hideki Yamaura, Takeshi Yanagihara

"For the production of partially composed metal matrix composites, namely discontinuous MMCs, using a casting· process, the interpenetrated phase composites with SiC particles were fabricated by pressureless iDfiltration using molten Al-Si alloys. This process is based on a wetting phenomenon, therefore, we discussed the technique based on the reactive wetting. The SiC particles coated by diluted water glass were sintered in a mullite Tammann tube and simultaneously infiltrated with molten Al-Si alloys in air at 1173~1573K. As for the improvement of the wettability between the SiC and the liquid aluminum alloy, Fe3O 4 powder was mixed with the water glass due to the thermit reaction between Fe3O4 and molten aluminum alloy. In some experiments, pure aluminum powder was placed on the sintered SiC to increase the interfacial area and the chemical reaction between the sintered Sic. and the melt. By combining these conditions, we succeeded in the complete infiltration without pressure at 1173K.IntroductionAs is well known, the mechanical properties of metal matrix composites (abbreviated MMCs) are superior than that of ordinary metals. However, their use has not been widely accepted because the production cost is very high due to their poor machinability. Therefore, the production of partially composed, namely discontinuous MMCs, by as the Lanxide process [l,2] has been investigated for many years. The Lanxide process, it takes a long time, sometimes up to 10h, in a nitrogen atmosphere for the infiltration. Therefore, the cost will be higher for common use. On the other hand, a high 'pressure process has been adopted for the production of discontinuous MMCs by the Toyota Motor Corp.[3]."

Jan 1, 2000

By Shantanu Chakrabarti, Khursid Alam Khan

"Globally, the use of metallic coated steel sheets in the automobile industry is increasing. The sheet should have excellent formability, weldability, paintability and corrosion resistance. Since bare cold rolled steel sheets have certain limitations, application of galvanized steel sheets is steadily expending. Galvannealed steel sheet fulfills all requirements and has become of major interest in the automobile industry.The success of Galvannealed (GA) steels in the body-in-white depends upon material design and parameters of various processes involved, like cold rolling, continuous annealing, hot dipping and galvannealing. In the present work, powdering resistance, one of the important product characteristics of GA, has been studied and a relation is established between the process parameters and the powdering value. The product obtained through optimization of the process parameters have been successfully used by major automotive producers without any powdering problem, for internal as well as external automotive applications.IntroductionThe present automotive industry demands that steel for the auto components should have excellent formability, weldability, paintability, corrosion resistance etc. In addition to this there is specific requirement for some particular components like high surface quality for skin panels. Corrosion resistance of panels is important requirment which determines the life of the particular component and brand value of the automotive. Among all the zinc based steel coating used in the automotive industry coating produced by Galvannealing process has received most attention because of its excellent weldability along with superior corrosion resistance and better paintability."

Jan 1, 2012