Search Documents

By Xin-liang Gao, Qing Li, Gui-qin Fu, Duo Jin, Miao-yong Zhu

"Optical microscope together with alternative wet-dry cyclic accelerated corrosion tests and XRD, SEM were employed on bridge weathering steel samples with different Mn and Ni contents which were vacuum induction melted and rolled to study their effects on the microstructure and rust layer evolution in er' containing condition. The results show that the microstructure is mainly ferrite and pearlite when Mn and Ni contents are 0.75 %, 0.42 %, respectively. Both the increase of Mn and Ni contents will make pearlite disappear while granular bainite appear, meanwhile the grain size decreases. With the increase of Mn content, the corrosion rate decreases in the initial stage, but the effect becomes little in the later stage. The increase of Ni not only improves the corrosion resistance of steel base at the initial stage but also hinders the tendency of further corrosion. As Mn content increases, a-FeOOH contents in rust layer decreases. With increase of Ni content, the content of a-FeOOH in the rust increases while that ofy-FeOOH decreases.IntroductionWeathering steels had been ~radually applied in manufacture of bridges owing to reducing the corrosion rate remarkably [I- l .Good weldability was needed for high performance bridge weathering steels. Since carbon was thought to be bad for weldability, low carbon content steel was adopted and Mn was added to amend the mechanical strength loss. Some scholars[6, 7l believed that Mn was beneficial for increasing corrosion resistance performance of the steel in marine atmospheric environment. Some scholars [S, 9l thought that Mn had little effect on corrosion resistance in marine atmospheric environment. Presently, the effect of Mn on bridge weathering steel in marine atmospheric environment still remained poorly understood. Ni was considered to be beneficial for increasing corrosion resistance performance in marine atmospheric environment [JO-l4l However, the high cost limited its application range. What would bring to the rust and corrosion by decreasing Ni content needed further research.Most researchers assumed that microstructures only affected the corrosion behavior of bare steel. But the study of Guo et al. P5l showed that the homogenous microstructures were beneficial for the corrosion resistance of steels. The effect of Mn, Ni content change on microstructure and microstructure on corrosion still remained poorly understood. In the present work, the effect of Mn and Ni on the microstructures of steel matrix, as well as the microstructures on the rust and corrosion was investigated."

Jan 1, 2014

By H. Kung, T. R. Jervis, M. Nastasi, T. E. Mitchell

"A systematic study of the structure-mechanical properties relationship is reported for nanolayered composites of MoSh-SiC, Mo-MoSh, Mo-MoShNx, MoSi2-MoSi2Nx, and Mo-MoShMoSi2Nx (x=3-4) synthesised by sputtering techniques. These composites have been studied by nano-indentation and cross-sectional TEM as a function of annealing temperature. As-deposited layers are amorphous except for Mo. With increasing annealing temperature, first MoSh and then SiC crystallize, while the hardness progressively increases until the layers start to spheroidize and grain growth sets in at 900ºC. For the case of Mo-MoSi2, the layers react and the composite deteriorates rapidly. However, MoSi2Nx remains amorphous up to 1000ºC, suggesting that it could act as a diffusion barrier between Mo and MoSi2. In fact the Mo. MoSi2Nx, MoSi2-MoSi2Nx and Mo-MoSi2-MoSi2Nx nanolayers are found to remain stable up to such temperatures. IntroductionMolybdenum dislicide, MoSh, is a potential matrix material for high temperature structural composites due to its high melting point and good oxidation resistance at elevated temperature [1]. The two major drawbacks for structural applications are inadequate high temperature strength and poor low temperature ductility. Silicon Carbide (SiC) being hard and thermally compatible with most ceramics and intermetallic compounds, has been found to be suitable for second phase reinforcement in various structural applications and, in particular, the addition of SiC whiskers improves the high temperature yield strength of MoSi2 [2]. While most of the research in MoSb-SiC composites has been on the particulate form of SiC, laminated composites may offer unique properties. It has been shown that synthetic multilayers with alternating layers of metal and/or compounds may exhibit interesting mechanical properties [3]. Enhancement in mechanical properties by decreasing the wavelength of multilayer spacing has been studied extensively. In general, two types of strengthening have been proposed: (1) Hall-Petch strengthening [4,5], where the strength increase is inversely proportional to the square root of the layer thickness; (2) Koehler modulus strengthening [6], which increases with modulus difference and decreasing layer thickness. In the present study, we have performed a systematic study of the relationship between strength and structure in a number of different nanolayered systems based on MoSh. Layer thicknesses have been varied and their nanostructures have been varied by heat treatment. Previous work on MoSi2-SiC is summarized [7]. In an attempt to improve fracture toughness, MoSh-Mo nanolayered materials have been prepared but are found to react and deteriorate. Previous work has shown that nitrided MoSi2 (MoSi2Nx with x=3-4) is highly stable [8] and so nanolayered composites of MoSi2-MoSi2Nx and Mo-MoSi2-MoSi2Nx have been prepared to assess the' stability and mechanical properties of these composites. Preliminary results are presented."

Jan 1, 1994

By J. Fogarty, J. Sofra

The mobile telecommunications sector is one of the fastest growing industries worldwide. However, increasingly stringent environmental regulations are placing pressure on manufacturers to accept responsibility for end of life products. The companies are therefore exploring avenues to recover the valuable components contained within the mobile telecommunications devices thus reducing the quantities of toxic components going to landfill. Batteries used to power the devices, are typically based on either nickel-cadmium, nickel metal hydride, or lithium ion cells. They contain toxic metals including nickel, cadmium, lithium, potassium, lead, and cobalt in a complicated arrangement of battery cells surrounded by a metals then plastic casing. The Ausmelt Catalytic Waste Converter (CWC) for waste treatment and recycling is well suited to processing all three mobile phone battery types for the recovery of valuable metals in marketable products that can be recycled to industry without turning out harmful levels of toxic emissions. Ausmelt recently demonstrated the capabilities of its CWC by continuously processing 4.5 tonnes of nickel-cadmium batteries. Using Ausmelt's pilot plant facility in Australia, the nickel-cadmium batteries were processed to produce a nickel iron sulphide (matte), a cadmium fume and a final slag which satisfied CS toxicity leach test criteria and was safe f<~r disposal to landfill. This paper explores the commercial development of the Ausmelt CWC for treating each of the three battery types in light of (a) the outcomes of the recent demonstration, and (b) the current and expected future availability of batteries for processing.

Jan 1, 2000

By Osvaldo A. Bascur

Several new hydrometallurgical plants have been built in the past years. They have implemented new processes to treat new type of ores. New technologies have been used to improve metallurgical performance from the start. The cycle times between knowledge generation and innovation are often neglected in the traditional capital expenditures and building of these new process plants. The paper reviews several implementations in which they have started with new ways of using information management from the beginning. The implementation of a real time performance management infrastructure is reviewed to assist in the implementation of mine to product strategies, metallurgical mass balances, solvent extraction composition statistical process control, methods to minimize organic losses, reduce variable costs and to improve metal extraction. Several examples are provided to improve operations by simplifying the access and analysis of information from assets and metallurgical processes. Continuous improvement and innovations have been enabled to minimize start times and for faster troubleshooting and resolution of operational problems.

Jan 1, 2006

By Seung-Whee Rhee

Characteristics of ceramic support made by spent foundry sand-loess mixtures are investigated by bulk density, porosity, durability, and compressive strength. And the basic properties of SFS and loess are estimated. The effect of drying time after cutting process, elevated temperature time, sintering temperature, and sintering time is also estimated to obtain the optimal condition in the process of manufacture ceramic supports. From the basic properties of SFS and loess, the content of SiO2 in furan sand is much higher than that in loess but the content of Al2O3and Fe2O3 in furan sand is much lower than that in loess. In order to make ceramic supports cylinder shape is the most desirable to sustain the properties of ceramic support. If annulus shape has a enough compressive strength, however, annulus shape may be decided. For the optimal condition to manufacture ceramic supports, drying time after cutting process is decided to 24 hrs and elevated temperature time is decided by 9hrs. And sintering temperature and sintering time are decided to 900 and 9hrs, respectively in order to prevent solidification of sand materials.

Jan 1, 2006

By Karl A. Gschneidner

Magnetic refrigeration was first used in the mid-1920&apos;s and new developments seem to have taken place about every 20 years, and this is especially true for the mid-1990&apos;s. The active magnetic regenerator magnetic refrigerator has the promise to become the first practical machine utilizing the magnetocaloric effect for cooling (and also heating). The basic principles are briefly discussed. Since the temperature lift for the magnetocaloric effect spans about 50 K, one will need to utilize several ferromagnets with different magnetic ordering temperatures in order to reach temperatures below ~250 K. The basic properties, behaviors, limitations, and new phenomena and knowledge are discussed.

Jan 1, 1997

By Zviad Kovziridze

The problems related to the production and research of SiC-Si3N4 composite are presented. The technology of producing the protective casings for tips and thermocouples is developed. Optimum composition charge and technological parameters are defined. The results of casing testing at production plants are presented.

Jan 1, 2006

By Sung Tae Kim

The viscosity is one of the most critical properties of slags and thus its influence on the physicochemical phenomena in metallurgical processes has been issued for last decades. The viscosity of ferrous- and non-ferrous metallurgical slags can be understood via structural investigation with spectroscopic methodologies including x-ray photoelectron spectroscopy, infrared- and Raman spectroscopy, and solid state nuclear magnetic resonance spectroscopy, etc. Therefore, the reaction kinetics such as desulfurization in ladle metallurgical furnace, reduction of FeO and MnO in electric arc furnace is strongly dependent on the viscosity of the slags. The rates of oxide (inclusion and refractory) dissolution into the slags and fluxes are governed by the viscosity. Alternatively, the structure of aluminosilicate melts also affects the thermochemical properties such as sulfide capacity, etc. These diverse applications of the viscosity-structure relationship to ferrous- and non-ferrous metallurgical processes were reviewed.

By Du Sichen

The present paper presents the modeling of gas-solid reactions in the case of the decomposition of CaCO3, describing the reaction kinetics on the basis of heat-transfer concepts which could be compared with thermogravimetric results. In the case of solid-solid reactions, the present paper describes the model developed for describing solid-solid reactions from dynamic X-ray diffraction technique, developed by the present team. The model has been successful in explaining the formation of spinel from MgO and Al2O3.

Jan 1, 2006

By Ibrahim Yusufoglu, Ahmet Orkun Kalpakli, Cem Kahruman, Sedat Ilhan

"The effects of oxalic acid concentration, temperature, stirring rate and particle size on the dissolution rate of synthetically prepared calcium molybdate were investigated. Dissolution of calcium molybdate in oxalic acid solutions takes place as a series - parallel type reaction. In the first reaction step, which proceeds according to the ""Langmuir - Hinshelwood Mechanism"", calcium aqua oxalato molybdate is formed as a complex chelate intermediate product. In the second reaction step, molybdic acid is formed during the slow hydrolysis of calcium aqua oxalato molybdate, and it reacts rapidly with oxalic acid to form the polymeric hydrogen oxalate dimolybdate chelate as an end product. Activation energies were calculated as 41.4 and 49.9 kJ mol-1 for the first and zero order reactions. The fractional conversion versus time relationship can be given by the following equation.IntroductionMolybdenum is used widely in electric-electronic, metal working, aerospace and aeronautic, nuclear, glass and petrochemical industries because of its high melting temperature and resistance against chemical effects. However, the largest molybdenum consumers are the iron-steel and super alloy industries where molybdenum is used as an alloying element. Industrially important molybdenum minerals are limited to molybdenite (M0S2), powellite (CaMo04) and wulfenite (PbMo04), which are considered as primary molybdenum resources. Secondary molybdenum resources are spent catalysts and scrap [1-4].Molybdenum has been produced by pyrometallurgical processes in the past. Since it is possible to process low grade molybdenum ores and industrial wastes by hydrometallurgical processes, which are more environmentally friendly than pyrometallurgical processes, the importance of the use of hydrometallurgical processes has increased in the molybdenum production industry."

Jan 1, 2012

By U B. Pal

Downsizing and decommissioning of nuclear facility operations is increasing the stockpile of various different grades of Radioactive Scrap Iron (RSI). Disposal of this material not only represents significant resource and value lost, but also necessitates long term monitoring for environmental compliance. The latter results in additional recurring expense. It is desirable to be able to decontaminate the RSI to a very low level that can be recycled or used for fabrication of containers for RSI disposal instead of using virgin metal to fabricate the container. Electro-Slag Remelting and Refining (ESR) is often used for decontaminating radioactive contaminated sources of scrap iron such as stainless steel. Non-radioactive oxides of cerium are used to simulate the radioactive oxide contaminants of Uranium and Plutonium. The success of the ESR process is strongly dependent on the capacity of the slag to rapidly incorporate the radioactive contaminant (simulant). In this study we have measured the slag-metal partition coefficient for cerium and investigated the reaction mechanism for the dissolution CeO, in the slag.

Jan 1, 2002

By Jin-Chun Kim

Nanosized W based powders (W, WC, WC-Co) were produced by chemical vapor condensation (CVC) process. Two different solid W(CO)6 and Co2(CO)8 metal-organic materials were used as precursors. CVC experiment was conducted in the temperature range of 400-1100. As-CVC WC1-x powder which had non-stoichiometric composition was carburized by using of the CH4-H2 mixed gas in temperature range of 750-850. The CVC W and WC1-x powders showed loosely agglomeration structure, and the Co powder had intricate long stand structure because of intrinsic magnetic properties of Co phase. Carbon content of the CVC powders controlled by gas-phase carburization was well matched with theoretical WC stoichiometry (6.13wt%).

Jan 1, 2006

By Huasheng Chen, Gaifeng Xue, Jing Zhang, Mingsheng He, Bin Liu, Yexian Ouyang, Shoujun Peng

Based on the investigation and study of the topography, microstructure and composition of the buildups which form in the surface of carbon sleeve in continuous annealing furnace for lowand medium-grade non-oriented silicon steel produced by CSP process, combined with production process of silicon steel, the mechanism and major causes for forming buildups of carbon sleeve are discussed from the factors such as CSP process, the quality of carbon sleeve and so forth. Meanwhile, some countermeasures to reduce the formation of the buildups are put forward.

Jan 1, 2015

By Chikabumi Yamauchi, Mitsuru Tanahashi, Tsuyoshi Taniguchi, Nobuo Furuta, Toshiharu Fujisawa

"It is essential to clarify the equilibrium relations among nonmetallic inclusions of the Mn0-SiO2-CrOx system and molten stainless steel in order to control non-metallic inclusions formed by the deoxidation of stainless steel with silicon. In the present study, the phase equilibria of the MnO-SiO2-CrOx system were measured by conducting the following experiments under controlled oxygen partial pressure, Po2, at 1873 K:1) Phase equilibria of the MnO-Cr20 3 binary system were measured for Po2 = 2 x 10-6 ~2 x 102 Pa.2) Phase equilibria of the MnO-SiO2-CrOx ternary system were measured for Po2 = 2 X 10-6 Pa.Based on the results, the phase diagram of this ternary system was established under the condition of the Si-deoxidation process of stainless steel (Po2 = 2 x 10-6 Pa and T = 1873 K).IntroductionAt the deoxidation stage in steelmaking process, generally multiple deoxidizers participate in deoxidation reactions, and the composition of deoxidation products ""non-metallic inclusions"" greatly varies depending on deoxidizing efoments and their contents. In order to control non-metallic inclusions formed by the refining process of steel, it is essential to clarify the equilibrium relations among non-metallic inclusions and molten steel.Especially, during the refining process of stainless steel, nonmetallic inclusions in molten steel seem to- change as follows. After the oxidation refining, Mn-chromite is formed in molten steel as non-metallic inclusion. By the deoxidation with silicon addition (mainly less than 1 mass%), Mn-chromite inclusions are changed their compositions to Mn-silicate. Segawa et al.[l] have reported the effect of amount of silicon addition on composition and mass ratio· of non-metallic inclusions during the Sideoxidation process of 18Cr-8Ni stainless steel at 1873 K, as shown in Figuri; L At higher silicon content than 0.5 mass%, only Mn-silicate was identified as non-metallic inclusion. On the other hand, at lower silicon content, both of Mn-chromite (MnO Cr2O 3) and Mn-silicate were identified. However, the thermodynamic and the kinetic analyses of the above-mentioned Sicdeoxidation process have not been made due to lack in the thermodynamic data for the non-metallic inclusions· of the MnO-SiO2-CrOx system, such as the phase diagrams, the activities of the components, and the free energy of intermediate compounds. In relation to the phase diagram of this system, those of the MnO-SiO2 [2] and the SiO2-Cr2O 3 [3] binary systems have been only reported"

Jan 1, 2000

By Jie Li, Shu Yang, Zhongliang Tian, Xun Hu, Yanqing Lai, Shaolong Ye

The electrolyte with high solubility for Sc2O3 is very important to realize the preparation of Al-Sc master alloy by the molten salt electrolysis. The solubility of Sc2O3 in K3AlF6- Na3AlF6-AlF3 melts is determined with an isothermal saturation method. The effects of KR (ratio of K3AlF6 to K3AlF6+Na3AlF6), the concentration of Al2O3 and the temperature on the solubility of Sc2O3 are also investigated. The results indicate that the solubility of Sc2O3 in K3AlF6-Na3AlF6-AlF3 melts increases and then decreases with KR increasing. The solubility of Sc2O3 is 8.698 wt.% in (K3AlF6-Na3AlF6)(KR25%)-18 wt.%AlF3 melts at 940℃. The effect of temperature on the solubility is little, and the values are 8.575 wt.% and 8.762 wt.% respectively when the temperatures are 930℃ and 960℃. The solubility decreases from 8.809 wt.% to 7.058 wt.% as the concentration of Al2O3 increases from 1.5 wt.% to 5.0 wt.% at 950℃.

Jan 1, 2015

By Marcelo B. Mourão

An experimental investigation was carried out to -study the rates of reduction of pellets containing iron oxides by carbon dissolved in liquid iron, at temperatures ranging from 1720 K to 1973 K. Several different pellet types were employed; the materials used in the pellet&apos;s manufacture were pure hematite, two kinds of commercial iron ores, and mixtures hematite/silica and hematite/lime: Reaction times were determined employing the constant volume pressure increase technique (CVPI). It has been observed that the reaction rate increases as the temperature and the pellet&apos;s specific surface area increases. The reaction rate is also affected by the oxide type: pellets made from commercial ores or from mixtures hematite/silica or hematite/lime show reaction rates lower than those made from pure hematite.

Jan 1, 1996

By Zhangm Mingming

Three samples received from the EAF shop were characterized by chemical, X-ray diffraction (XRD), optical microscopy (OM) and scanning electron microscopy (SEM) methods. The objective of this characterization work was to investigate the occurrence of nickel, copper, zinc, sulfur and phosphorus and to identify their origin and associations with iron minerals in the concentrate samples from the mines. The samples were identified as MINERAL, PELLET, and HRD. The latter is the DRI product. All three samples were received as fine powders. The results indicate that, in the mineral sample, magnetite is the major iron oxide mineral with hematite as a second phase based on the OM and XRD studies. Pyrite [FeS2], chalcopyrite [CuFeS2] and bravoite [(Fe,Ni)S2] are the major sulfide minerals. Trace amounts of apatite [Ca5(PO4)3(F,Cl,OH)], wardite [Na4CaAli2(PO4)8(OH)8 6H2O], giniite [Fe;(PO4)4(OH)3 2H2O] and vivianite [Fe3(PO4)2 8H2O] were identified by SEM and XRD. Microscopic studies also indicated that most of the sulfide grains in the mineral sample are present either as liberated fine particles (about 10 microns) or as inclusions within the magnetite and hematite grains. XRD studies revealed magnetite as the major mineral with subordinate amounts of hematite and pyrite confirming the microscopic findings. Copper, nickel, and zinc are mainly present as chalcopyrite, bravoite, and franklinite [(Zn,Mn,Fe)(Fe,Mn)2O4] in trace amounts in the mineral samples, respectively. Impurities carry over to the pellet and HRD samples. Chemical analyses of the three iron-bearing samples indicate that sulfur and phosphorus in the pellet sample exceeded the specification. Since liberated pyrite and chalcopyrite particles were observed in both the mineral and pellet samples, magnetic and flotation processing routes should be effective for sulfide removal but at the cost of iron losses. The high phosphorus content of all three samples indicates that there are phosphates which are difficult to remove by the current concentrating processes (magnetic separation and flotation).

Jan 1, 2012

By L. Y. Zhang

The current status of metal hydride alloys for NiMH batteries was systematically reviewed. Extensive application-oriented research and development has successfully made the NiMH battery an important part, with growing potential, among rechargeable batteries. The rare earth based metal hydrides (AB5) have been considered the best alloy material for use in the negative electrode in NiMH batteries. However, being in demand for high performance electronic markets, the still young NiMH industry is facing serious technical challenges in developing better products. Among all the efforts to respond to the challenges, advanced AF3, alloys are in great demand: the capacity enhancement race requires new or improved alloys possessing higher volumetric capacity; price competition mandates MH materials with low cost; high performance under severe service environments calls for alloys with high corrosion resistance when subjected to electrochemical cycling; and finally, high power service requires the negative electrode to deliver current at high rates.

Jan 1, 1997

Novel techniques were developed to obtain samples from and make measurements in the shaft of the flash furnace at the Kalgoorlie Nickel Smelter. The data obtained was used to validate mathematical models of the burners and the reaction shaft. Particle, gas and wall temperatures were measured along with the oxygen potential of the molten particles. Collected particles were characterised by sizing, chemical analysis and optical microscopy. The region of the shaft immediately beneath the burner where the rate of change was most rapid received special attention.

Jan 1, 1993

By Carla Lupi, Mauro Pasquali

"Photographic technology is based on light sensitivity of silver halides that, because of silver properties, are capable of forming photographic images. Photographic laboratories and hospital departments because of digital photographic systems less use this technology today. Nevertheless recovery of silver is still advantageous because environmental problems related to Ag ions danger to biological system. Many processes have been studied to treat silver containing photographic bath: cementation, chemical precipitation and electrowinning. In this work, after preliminary voltammetric tests, a batch electrometallurgical process has been studied to completely deplete the silver containing photographic fixing baths. The effect, of silver concentration in the electrolyte, varying over the range 0,2-1 g/L, bath stirring and current density ranging from 10 to 500 A/m2 on process yield and deposit quality, has been investigated. Introduction Photographic wastes, electronic scrap and spent catalysts constitute the main sources of materials for silver recycling. Among those silver secondary sources, the photographic discharged material could be still important and useful, even if photographic laboratories and hospital departments, because of digital photographic systems, less use photographic technology. Several processes have been developped in order to recover silver used in the field of photography from both photographic solutions and scrap film paper[1-5]. Fixing solutions are very complex baths but, because of silver position in the electromotive series, electrolysis could represent an advantageous method for silver recovery. Electrolysis produces high purity silver without generating new pollutants, while the fixer can be reused: obviously it is necessary to purge off a portion of this solution in order to avoid the excessive build up of other deleterious compounds into solution. A tested recovery method was constituted by the dissolution of silver from X-ray films with concentrated nitric acid. Internal electrolysis and external electrolysis methods were carried out using a steel electrode as cathode and a copper electrode as anode [6]. Silver recovery from photographic chemical solutions has been also performed in a special cell [7]: the solution is supplied to the bottom of a non-agitated cell having a vertically elongated form and including a central anode enclosed by a cathode. An other study discloses the use of an electrolytic cell comprising at least one anodic compartment and one cathodic compartment: the solution is treated in the cathodic compartment and then recycled in the anodic one [8]. A more recent work proposes the use of zirconium cathode for the recovery of silver from photographic fixing solution [9]: studies carried out by cyclic voltammetry showed that about 98% of total Ag can be recovered with an electrical efficiency close to 92%."

Jan 1, 2008