Search Documents

By Stein Tore Johansen

Some ferro-silicon fumaces have heat-recovery equipment. Here, the recovery of electric energy from the off-gases can be increased by increasing the off-gas temperature. This is easily done by reducing the amount of air which usually is mixed into the off-gas to cool the gas mixture. If the off-gas becomes too hot problems with severe fouling or clogging of the gas channels? close to the fumace is observed~ The result is irregular stops to clean the off-gas channels. The paper focuses on the nature? of the clogging phenomena and some of the ways to avoid clogging. A detailed experimental study was carried out at the Elkem Thamshavn Plant. Theoretical studies were performed to understand the particle deposition, turbulent multiphase fluid flow and off gas combustion in the off-gas channels. The study has resulted in reduced clogging.

Jan 1, 1992

By Chuanyu Feng

In this paper, a load-based micro-indentation technique suitable for field applications was developed. This technique bears the same theoretical background as traditional load-depth sensing indentation, and does not need any direct measurement of indentation depth or contact area. The removal of this requirement will reduce much of the cost associated with traditional instrumented indentation. To demonstrate the feasibility, a portable indentation system suitable for online material characterization was developed. Design issues of the portable unit were discussed and preliminary results using the portable unit were also presented.

Jan 1, 2009

By Kazuki Morita, Ye Wang

In order to optimize the B removal during slag-refining process for solar-grade silicon production, a new process for the removal of B in molten Si was proposed based on the principle of oxidized chlorination and evaporation. B can be generated and evaporated in the form of B-containing gas (BOCl) from molten Si using CaO–SiO2–CaCl2 slag system. Compared with the binary systems of CaO–CaCl2 and SiO2–CaCl2 slag, the ternary slag system CaO–SiO2–CaCl2 showed a better potential (90 pct) for B removal at 1723 K for 2 h. Moreover, the diffusion coefficient (D) of B in the slag was also determined using tube-molten pool method. Through this, it was found that the rate-limiting step of B-removal in the slag refining process is controlled by B transfer in the slag interface and surface.

Mar 1, 2017

By Amy Nelson

In the electrolytic production of zinc, cobalt is removed from the zinc electrolyte by cementation with zinc dust prior to electrowinning. Although the thermodynamics for this reaction are favourable, kinetic barriers to cobalt reduction render the method almost useless in practice unless activators such as copper and antimony or arsenic are added. There is a large body of work studying the effect of these additives, yet the mechanism by which they act is still poorly understood. Even when the target conditions are met, zinc dust consumption is excessively high: satisfactory operation requires up to 300 times the stoichiometric amount of zinc dust. The objective of this work is three-fold: (1) to examine the effects of activators and elucidate the characteristics that make a good activator; (2) to identify new additives that could lead to a more efficient purification process; and (3) to test the new additives with synthetic and real electrolyte solutions. The present paper gives a status report on this project.

Jan 1, 1998

By M. E. Karabin, R. J. O'Malley

"A mathematical model of the roll casting process has been developed which predicts macro-variables, such as roll separating force, roll torque, and strip exit speed for a range of roll speeds. Continuum variables, such as interface pressure, interface shear stress, freeze-front shape, and internal temperature distribution are also predicted.The model consists of two independent segments: solidification and rolling. The solidification model is two-dimensional (thickness and rolling direction) and is capable of handling alloy solidification. The solidification model is employed until solidification through the thickness is complete, then the rolling solution is activated.The rolling model is a one-dimensional (rolling direction) mechanical solution based on the von Karman approach, coupled with a two-dimensional thermal solution. The flow stress is expressed as a function of the average through-thickness temperature of the strip.Experiments were performed using a laboratory roll caster to test and refine the model. Experimental strip exit temperatures were used as input to the model. Experimental and predicted roll torque and strip exit speea were forced into agreement at a single reference roll speed to obtain values for the coefficient of friction and the interfacial heat transfer coefficient. Using these values, good agreement was obtained between predicted and experimental torque and strip exit speed over the entire range of roll speeds examined."

Jan 1, 1986

By E. S. Peterson

The selective separations of trace metals- and organics from water are processes of importance to industry. The application of a new metals capture technology coupled with polymer membrane technology has proven to be one avenue to accomplish such selective separations. The polymers used in these studies are polyphosphazenes. Polyphosphazene polymers consist of an alternating backbone of nitrogen and phosphorus atoms. The polymers have high thermal and chemical stabilities. Experiments at the Idaho National Engineering Laboratory demonstrate that polyphosphazene membranes coupled with Chromato Chem,"Chelation Chromatography" process are capable of removing both chlorinated hydrocarbons and metal ions from process streams. These results point to a wide range of potential industrial and environmental applications for such systems. Data will be presented which show the efficiency and selectivity of separations, postulated separation mechanisms, and the initial designs of industrial demonstration units which are currently under construction. Parts of this work have been performed under a Cooperative Research and Development Agreement (CRADA) between ChromatoChem, Inc. and Idaho National Engineering Laboratory (INEL). The work at INEL was been sponsored by the United States Department of Energy's Office of Industrial Technologies

Jan 1, 1995

By Thomas J. O'Keefe, Pu Yu, George Houlachi, Xuewen Tang

"Impedance measurements were used to investigate the electrochemical characteristics of acidic zinc sulphate electrolytes containing Sb3+, gelatin and their mixtures. The data were correlated with cyclic voltammetry curves made using synthetic as well as industrial electrolytes. The cyclic voltammetry results were similar to those obtained in previous studies in that antimony caused a depolarizing effect while gelatin gave an increase in the potential for zinc nucleation on an aluminum substrate.The electrochemical impedance spectroscopy (ElS) evaluations were conducted on electrodeposited zinc at three overpotential values. The potentials were chosen to represent various current density regions in the zinc polarization curves. The antimony and gelatin gave characteristic impedance plots which correlated with expected behavior, particularly current efficiency. Both antimony and glue appear to modify the intermediate zinc reaction sequence, but in different ways. The data strongly suggest that film formation and stability are major factors in the zinc ion reduction mechanism.IntroductionThe zinc electrodeposition process is sensitive to the presence of a variety of organic and inorganic chemical species in the electrolyte [I]. Such components can produce either beneficial or harmful effects, depending on their relative concentrations and electrochemical behavior. Extensive investigations have been made to gain a better understanding of the changes occurring during zinc deposition in the presence of such additives. Techniques employed include microscopy, x-ray diffraction, dynamic voitammetry, current imd energy efficiency studies [2-5]. Ultimately, the objectives are to identify the factors which most affect the efficiency of the process and to provide a means to effectively control them.One of the most harmful impurities is antimony, which can be detrimental when present at concentrations as low as 10 to 20 parts per billion. Dramatic changes in zinc polarization behavior, deposition structure and current efficiency have been observed with antimony in the electrolyte. Antimony appears to lower the hydrogen overpotential by hydride formation or a similar catalytic mechanism, which allows an increase in localized corrosion and zinc dissolution [6-8]."

Jan 1, 1997

By Bryce Clark

An outline of the current world's known sources and resources of cobalt, looking at both land and possible undersea deposits, is given as a prelude to an examination of current and historical actual world production on geographic/company basis. These production figures will be compared to apparent consumption by segments, both geopraghically and end-use based. Consumption of cobalt has been regarded as price sensitive and a historical look at prices against all other figures will be considered. Included in this scenario will be a brief overview of cobalt's uses and a comment on future trends. Tables will include: Resources, Production, Consumption, Prices, Markets.

Jan 1, 1993

By Y. Shigeno

The reactivity of a porous solid is a strong function of its pore structure (porosity, pore surface area and pore size distribution). It follows that reactivity could be altered by altering pore structure; one way to achieve this is by chemical vapor infiltration whereby a gaseous species is reacted in the porous solid to produce a solid. Experiments were carried out in which the pore structures of various carbons were modified by cracking methane within the pores; oxidation rates of the carbons were then measured for both infiltrated and original samples. For coke it was found that two indices of coke performance used in the steel industry (CRI and CSR) can be greatly improved following a small amount of infiltration. Infiltration/oxidation results are interpreted in terms of measured pore structure changes.

Jan 1, 1993

By Carlos G. Levi

"The principles involved in the rapid solidification of supercooled metal droplets and existing numerical models are reviewed. The limitations of these models for studying alloy solidification are discussed in terms of the effects of alloying elements on the relevant heat transfer, thermodynamic and kinetic parameters. Analysis of the enthalpy-temperature diagram reveals how the extent of rapid solidification is hindered by the addition of solute. A solidification model incorporating thermodynamic and kinetic relationships into a Newtonian heat transfer formulation is used to analyze the thermal history and concurrent solute redistribution during recalescence. IntroductionIt is well acknowledged that microstructural evolution during solidification is intimately associated with the thermal history of the liquid-solid interface. Structural parameters like chemical homogeneity, morphology and size scale of the phases can be related to the interfacial temperature and velocity. These in turn change by the interaction of the interface with the thermal and solutal fields in its neighboring environment.The thermal history of powder solidification can be conveniently described on the enthalpy-temperature diagram for a pure metal shown in Figure 1 and discussed in detail elsewhere [1). A system can conceivably follow any path of decreasing enthalpy in the supercooled region of Figure 1 (~ < 1), starting at the nucleation temperature (oN < 0) on the liquid line, and ending at some point on the solid line. A vertical path represents an isothermal transformation, of which a limiting case is solidification without significant barriers to nucleation and growth, with the interface at the equilibrium temperature TM (path one in Figure 1). A horizontal path represents isenthalpic (or adiabatic) solidification whereby the system could form an amount of solid proportional to the initial supercooling of the liquid without further heat loss to the environment. A liquid that can completely transform to solid under adiabatic conditions is said to be ""hypercooled""."

Jan 1, 1986

By C. L. Lin

Multiphase, irregularly-shaped randomly-oriented PARGEN particles were grown to determine the breakage/liberation characteristics of such locked particles. The simulated locked particles were randomly broken to establish the liberation characteristics of the broken fragments. The progeny size distributions are consistent with Gilvarry&apos;s volume and surface flaw model for single particle breakage. The extent of liberation of both continuous and dispersed phases can be described from the conservation of interfacial area. In this regard the data can be normalized and liberation described for a wide range of dispersed phase grades and dispersion densities.

Jan 1, 1988

By Nagy El-Kaddah, Thinium T. Natarajan

A modeling strategy is presented for computing the electromagnetic field and the shape of the molten metal in electromagnetic confinement systems. This strategy involves the use of a hybrid finite element/integral technique to calculate the electromagnetic field and force distribution in the melt. The free surface shape is determined from minimization of electromagnetic, gravitational and surface tension energies using the Lagrange method of multipliers. This approach was applied to model the electromagnetic levitation melting process. The model was found to accurately predict the measured shape of levitated droplets.

Jan 1, 2014

By Victor Stancovski, Uday Pal, Stephen C. Britten

"An in situ electrochemical technique for measuring the concentrations of easily dissociable oxides in slags at temperatures between 1200-1600°C is being developed. The technique utilizes a partially-stabilized-zirconia solid electrolyte (PSZ), which conducts oxygen ions, to separate a reference-gas compartment from the slag of interest. Three types of measurements are currently under investigation which yield different information concerning the slag phase and hence will be combined into a single amperometric device for monitoring the properties of easily dissociable slags.Type I utilizes an open-circuit-voltage measurement between the reference gas and the slag phase. Type II utilizes a potentiostat to apply a direct current potential step or sweep between the inner and outer compartments of the electrolyte, driving oxygen ions from the slag into a reference gas. With the use of open-circuit-reference electrodes, the resulting current-potential profile reveals the dissociation potential and concentration profile of dissociable oxides such as those of iron, manganese, and chromium. Information on the transport properties of the cations can also be generated from these measurements. Type III utilizes a potentiostat with reference electrodes to carefully electrolyze a known volume of slag by removing large quantities of oxygen ions from the slag to the reference gas. The coulombs of charge removed at different applied potentials can be used as a direct indication of the concentration of each dissociable oxide species present within the slag."

Jan 1, 1997

By Donna M. Noel

Bacterial strains have been cultivated from solids previously exposed to cyanide that will tolerate 300 ppm sodium cyanide under anaerobic conditions. In selected solid samples, these bacteria have been shown to reduce the level of cyanide from approximately 300 ppm to essentially zero in about 50 days under anaerobic conditions. Various media were investigated, and the nutrients providing maximal growth were ?established .. Degradation of cyanide in sterilized solids was determined for comparison with degradation obtained in bioactive solids. All experiments were conducted at ambient temperature and initial pH of approximately 10.5.

Jan 1, 1991

By Jie Li, Thomas A. Rawdanowicz, W. J. Collis, S. Venkatraman, S. Iyer

"InSb being the lowest band gap. material amongst the 111-V semiconductors with low effective mass has long attracted research interest, due to its potential application in far infrared devices and for high speed circuit elements. In this paper, we report, for the first time, Te-doping of InSb on GaAs substrate using SnTe doping source with molecular beam epitaxy (MBE) technique and its electrical characterization. The undoped epilayers are n-type in the temperature range of 10 K to 300 K investigated. The room temperature (RT) mobility as high as 64,810 cm2/V·s (1.9x1016 cm-3) have been measured on a 4.8 µm thick epilayer. Sn Te doping at different doping levels were investigated. 5. 7 µm thick doped layers with RT carrier concentrations ranging from 2x1016 cm-3 to 3.2x1018 cm-3 with corresponding full width at half maximum (FWHM) of x-ray (400) rocking curve varying from 170-200 arc-seconds have been achieved. The Hall mobility of 20,000 cm2/V·s at 1.3xl018 cm-3 carrier concentration was obtained indicating that SnTe is a good candidate as source material for n-type doping of InSb.IntroductionThe thin films of InSb and InSb-based alloys have found considerable interest because of potential applications in III-V semiconductor-based infrared optoelectronic devices1• In addition, the advantage of the small effective mass and the consequent high mobility can be utilized in high frequency and high-speed circuit devices2 InSb can also be used in magnetoresistive sensors for position sensing3. Epitaxial InSb films grown by MBE may be doped n-type with Si or Sn, or with the group VI elements, namely, S, Se, or Te. Of the group VI elements, Te may be advantageous because of its relatively low vapor pressure. However, the vapor pressure is high enough to have sufficient memory effect during MBE growth. Hence different telluride compounds such as GaTe45, PbTe6 and Sb2Te37 have been used as the dopant source for Sb-based compounds. SnTe has also been used as a successful n-type dopant in the MBE growth ofGaSb8 But, to our knowledge, there is no report on the investigation of SnTe doping of InSb. In this paper, we report the first doping characteristics of SnTe in InSb layers grown on GaAs substrate."

Jan 1, 1998

By V. Montenegro

Smelting of copper concentrates in Teniente Converter produces highly oxidized slag, containing from 4 to 10 % Cu and from 15 to 25 % of Fe304. Copper recovery requires magnetite reduction at a level of 5%, determining the degree of cuprous oxide co-reduction and the liberation of copper matte inclusions. The rate of slag reduction is controlled by the mass transfer to the reaction interface. Slag stirring affects the rate of reduction and enhances coalescence of mechanically entrained copper matte inclusions. Slag reduction and sedimentation in the AC electric furnace is a commonly used method of slag cleaning. Utilization of DC electric furnace creates beneficial conditions introducing slag electrolysis additionally to chemical reductions with carbon of coke and electrodes. Application of external magnetic field, interacting with a direct current in an electric furnace, induces magnetohydrodynamic phenomena, such as intensive stirring and electromagnetic buoyancy force acting on inclusions. Laboratory scale research in simulated DC electric furnace with a superimposed magnetic field showed a significant acceleration of the rate of slag reduction and copper removal. Continuous measurement of gas flow and composition allowed for determination of the reduction rate along the time. Application of external magnetic field in the reduction of the industrial slag in a crucible simulated DC electric furnace results such as the increase of the reduction rate from 2 to 3 times, compared with the identical conditions in the AC electric furnace. Interaction of non- homogeneous electric field with crossed permanent magnetic field induces vigorous slag stirring, enhance mass transfer and accelerate the rate of the slag reduction. Additional participations of the slag electrolysis in the magnetite and cuprous oxide reduction as well as the acceleration of the settling of the inclusions by the electromagnetic buoyancy force affect the slag cleaning intensification.

Jan 1, 2003

By A. Haxhiaj, E. Haxhiaj

"The paper has as a studying object the issue of effective management of gasses’ heating and dusts in reductive melting process in lead (Pb) metallurgy. It also analyses the issue related to the usage and recycling of dusts and gasses in all pyro-metallurgical processes of technical lead production. The paper contains the analysis of technological process of separation of humidity, gasses, and dusts of valuable remainders in “Trepça” plant. Paper has the results of theoreticalexperimental studying, analytical and graphical of gasses thermal balance depending on height and composition of load, and the coke quantity on load for reductive melt in “Water-Jacket” furnaces. With thermal balance, having into consideration all parameters of heat in entry and exit depending on aforementioned factors we aimed to optimize the parameters of the process, keeping the attention to the minimization of energy consumption, and the overall influence on environment.1. IntroductionThe upper part of the furnace which is the study point of this paper lies from the reactions zone of Water-Jacket furnace and it also includes the furnace neck. In this zone has been elaborated the zonal material balance referenced third in the row. The separation of humidity, dusts, gases and lead with gases depends on many parameters like temperature, load composition, and height of load inserted in the furnace, and also the height of preheating zone in Water-jacket furnace. Lead oxidizes in reaction zone of the furnace and exhales with gases like dusts and small particles after which falls in worthy storage of Trepça plant and has negative effects in environment, and economic stability of reductive melting process of Water-jacket furnace. Thermal balance of gases in this zone depends on many factors; height and load composition, coke quantity in a load. The calculation has been done as the standard methodology of thermal calculation is done; moreover, by using a computer for mathematical models which enables very accurate results. We must emphasize that acquired and used heat in reaction zone and melted materials is calculated in others studies, so their influence in preheating zone is assumed."

Jan 1, 2010

By Liping Gu, Gordon A. Irons

"A 1/3 scale ""thin-slice"" model of an electric arc furnace was developed so that gas could be injected to simulate foaming gas evolution. The influence of arc jets, oxygen lancing and bottom bubbling was also simulated. Liquid velocities were measured by a white light particle image velocimetry system. Numerical simulations of some of these effects were made using commercial CFD packages. Comparisons with measured results show that considerable care is required to select the appropriate model and to interpret the computational results.INTRODUCTIONDuring recent years electric arc furnaces (EAF) have captured a significant share of steel production, partially due to increased productivity through the introduction of advanced technology such as oxygen injection, slag foaming and long-arc operation, process automation and post-combustion. However, systematic analysis of the process and these effects on heat transfer and fluid flow in the furnace is still in its infancy. Most investigationsl1 6l have been restricted to a specific application such as oxygen lancing or bottom stirring. In addition, it is very difficult to make comparisons between these computed results and experimental/industrial results. In this work a 1/3-scale ""thin-slice"" model of Dofasco's 190 ton EAF was built. The fluid flow in the bath due to the arc jets, bottom stirring, oxygen lancing and CO evolution was simulated. The velocity distributions in the bath were measured using Particle Image Velocimetry (PIV) System. In addition, numerical simulations of bottom stirring and CO evolution were carried out using two commercial CFD packages (Fluent and Phoenics). The objective of this work is to validate the mathematical models so that they can be applied to the full-scale furnaces."

Jan 1, 1999

By Nagahiro Saito, Takahiro Ishizaki, Daisuke Yata, Akio Fuwa

"Ternary compound-semiconductor, CuInTe2, film was deposited cathodically under potentiostatic conditions on titanium substrate from aqueous solution containing CuCl2, InCl3, TeO and HCI in this study.The deposition parameters such as electrolytic solution composition, potential and temperature were optimized· for electrodeposition of CulnTe2. Structural characterization of the: deposited film was also carried out using XRD and SEM. Electrodeposited films Were prepared and analyzed for their chemical composition using ICP. The ICP analyses showed that the stoichiometry of the films could be controlled by (1) the deposition potential and/or by (2) the electrolytic bath composition.1. IntroductionThe ternary chalcopyrite type compound semiconductors exhibit such electrical, chemical and optical properties that make them promising for photovoltaic devices (Kazmerski and Wagner 1985)(1). Many researches have been devoted to the characterization of these materials for over one and a half decades. High efficiency solar cells based on p-CulnSe2/n-CdS have been reported (Mickelson and Chen 1983)(2).The electrodeposited fil ns of semiconductors have more advantage than other physical and chemical deposition techniques; it is relatively easy and economic technique and the semiconducting properties such as band-gap variation, concentration of dopant stoichiometric composition and so on can be controlled with some accuracy. The electrodepositions of the ternary CuInS2, CulnSe2 have been reported by many workers (Hodes and Cahen 1986, Bhattachaya 1983, Singh et al 1986, Lokhande and can be prepared as both p-type and n-type. Therefore, its potential for application in optical and photovoltaic devices is one of the great interests. Bhattacharaya and Rajeshwar (1986)(9) reported the electrodeposition of CuInTe2 from an acidic bath· on indium tin oxide (ITO) and Mo substrate. Triethanolamine (TEA) was used as a complexing agent for indium. The electrodeposited CuInTe2 films were non-stoichiometric in composition under all their experimental conditions by electron-probe micro analysis (EPMA) and Auger depth profile analysis. In this paper, we report our results on the behavior .of Cu-In-Te electrodeposition from ·acidic baths; the preparation of CulnTe2 and the effect of bath composition on electrodeposited films obtained."

Jan 1, 2000

By K. G. F. Janssens

In the process of annealing a deformed metal the microstructure changes due to concurrent recrystallization, grain growth and precipitation. It is common knowledge that all three of these microstructural transformations show a strong dependence on each other, and that an overall model must take the relevant interactions into account. Aiming at the development of an approach which is useful in the more general case, a computational model is being developed which allows the prediction of the three dimensional grain topology and orientation distribution function of any metal submitted to subsequent deformation and annealing, taking into account concurrent recrystallization, grain growth and precipitation and starting from a statistical representation of the deformed microstructure. In this contribution a case study is presented which illustrates the potential and limits of the state of the art in the field. Keywords: Microstructure Evolution Modeling, Irregular Cellular Automata, Deformation, Precipitation, Recrystallization, Grain Growth

Jan 1, 2003