Search Documents

By Anna Wasilkowska

The study concentrates on the effects exerted by microstructure, deformation history and uniaxial stress conditions (temperature, stress state, strain rate) on the mechanical properties offerritic TRIP-aided steels for automotive applications. In low-alloyed TRIP-steels it is quite difficult to separate the effect of the austenite to martensite phase transformation from the influence of the ferritic matrix contributing to the yield stress and uniform elongation. Investigation of transformation kinetics of retained austenite as a function of the deformation temperature show that using the parameter k to characterize the retained austenite stability allows to identify regious of different temperature sensitivity separated by a transition temperature of 10±5°C. The observed low strain-rate sensitivity of the flow stress is an intrinsic property of the ferritix matrix and points to defomtation governed by slip. The ultimate tensile strength is much stronger affected by temperature than the yield stress. The influence of the temperature on the elongation is complex, because of the heating of the specimens by 60-l20°C at moderate and high strain rates. The increase of the total strain can be understood in terms of thermal softening of the ferrite. On the other hand, the steep increase of the stress during dynamic testing is an effect of accommodated elastic and plastic strains in the matrix. The strain- hardening exponent is dependent on the conditions imposed during testing. The martensite transfomtation rate is lower and the critical stress for martensite nucleation is much higher under compression compared to tensile loading. In secondary tensile tests, the yield stress increases steeply, and the ultimate tensile strength and the total elongation depend linearly on the amount of pre-straining. The results confirm that in the range of 8=10-4 s-l the TRIP-effect governs room temperature plasticity. Keywords: TRIP-steels, mechanical properties, strain rate sensitivity, temperature sensitivity, austenite stability

Jan 1, 2003

By Gordon A. Irons

"Powder injection for melt refining is widely practiced in the steel industry, and is gaining acceptance in the non-ferrous industries. In these commercially-important systems, the thermodynamics and kinetics may be very complicated. More than one element may be removed by refining, and often the refining agents are not just one compound. In this paper, the thermodynamic and kinetic aspects of these processes are reviewed. A number of examples are given, such as the desulphurization of iron with a variety of reagent mixtures, and selenium removal from copper with several different reagent combinations.IntroductionI am very pleased and honored to present a paper at this Symposium recognizing the many contributions of Professor Howard Womer. Even at the time I was an undergraduate student, the WORCRA process was part of the curriculum. I remember at the time that I was fascinated by the concept, and due to it and the many other rapid developments in Process Metallurgy, I chose it as my field of study. I think the Symposium is testimony that Professor Womer has touched the lives of many others as well.My original assignment was an overview of the basic aspects of gas and solids injection. However, I reviewed most of this material at the Savard/Lee Symposium [1]. In the present paper, I will present some of the basic issues related to refining with powder injection, using work that we have recently completed in both ferrous and non-ferrous systems."

Jan 1, 1996

By K. Morita, S. Ueda, Y. Matsuki

Tellurium has mainly been used as an alloying element for resulfurized free-machining steel. It globularizes MnS inclusions and improves both machinability and mechanical properties of such steel. This effect is quite sensitive to tellurium concentration.Therefore,its incorporation should be controlled accurately during the secondary refining process, using the thermodynamic properties of tellurium in molten iron. In the present study, Wagner’s interaction parameters of various elements on tellurium were experimentally evaluated by vapor-liquid equilibration, and the vapor pressure of tellurium was controlled using the transpiration method. The values obtained were compared with those of oxygen and sulfur, and they were found to be correlated with the standard Gibbs energy of formation of the corresponding oxides, sulfides, and tellurides.The results indicate that the relations described here could provide estimates of interaction parameters that have not been experimentally determined thus far by using available thermodynamic quantities.

Mar 1, 2017

By Liu bing-guo, Peng Jin-hui, Guo Sheng-hui, Kong dong-cheng, Hu jin-ming, Zhang Li-bo

The novel technology of calcination to prepare triuranium octaoxide（U3O8）from ammonium uranyl carbonate in microwave fields was investigated on the basis of the temperature rising characteristics of ammonium uranyl carbonate, triuranium octaoxide (U3O8), and their mixture. The result of experiments show that ammonium uranyl carbonate had weak capability to absorb microwave energy, while triuranium octaoxide has the very strong capability to absorb microwave energy and the sample temperature increased rapidly with an increase mixture ratio of triuranium octaoxide. The optimal calcination conditions were as follows: microwave power 700 W, calcination time 10 min and 60 g in this experiments range, respectively. Under these conditions the value of total uranium and 4 U of triuranium octaoxide was 84.28% and 31.02%, respectively. It is feasible to prepare triuranium octaoxide by calcination from ammonium uranyl carbonate, which mixed with small amounts of triuranium octaoxide under microwave fields.

Jan 1, 2015

By Kenneth P. Michalek, James E. Kelly, Jonathan A. Dantzig

"Many investigations have been reported regarding the simulation of continuous casting with emphasis on in-mold heat transfer. These analyses have been limited, however, because they require either estimation or measurement of the characteristic heat transfer between the ingot and the mold. In this paper, a self-consistent model 'is presented for calculating the heat transfer between a solidifying continuous casting and the mold, in the context of the continuous casting of steel. Using both thermal and stress analyses, the air gap formed during continuous casting is calculated and used to compute the heat transfer coefficients. Iteration between the thermal and stress analyses is used to determine a self-consistent solution. IntroductionThe continuous casting process for steel is illustrated schematically in Fig. 1. Molten steel is tapped into a tundish from which it flows at a controlled rate into the continuous casting mold. The initial shell of the casting forms in the mold by transfer of heat from the metal through the mold wall to the cooling water. The remainder of the casting is solidified by application of water sprays, and/or radiation cooling below the mold.Heat transfer in the mold portion of the process is important because it controls the formation of various defects which are deleterious to subsequent processing. Examples of defects formed in this region are surface irregularities, such as cold folding and oscillation marks, and more serious defects, such as longitudinal or transverse cracks. A more catastrophic problem which may occur is a breakout, in which the shell ruptures and molten steel is discharged in an uncontrolled way."

Jan 1, 1986

By Xiang-dong XING, Zhen-yang wang, Jian-Liang Zhang

Distribution behavior of titanium between CaO-SiO2-MgO-Al2O3-TiO2 and hot metal was studied between 1350 °C to 1600 °C. Experimental results indicate that the reaction temperature influenced the activity coefficients of titanium and resulted in the variation of equilibrium constant. Finally, the Gibbs free energy formula of titanium carbothermic reduction was fit out using the thermodynamic model of Wagner and congregated electron phase models.

Jan 1, 2015

By R. E. Brewer

Pilot scale flotation tests were conducted with a l?ft-diam column at the Barrick Resources (USA) Mercur mine, Tooele County, UT, to scavenge unleached (0.01 to 0.018 oz/st) gold values from the tailings of a carbon-in-leach (CIL) circuit. The optimal recovery was 35 pct of the unamenable-to-leaching gold, at a grade of 0.353 ounces of gold per short ton, using a mixture of dithiophosphate, xanthate, and diesel fuel as a collector. This was achieved by floating approximately 1.6 wt pet of the CIL tailings. The gold values are believed to be contained in arsenic-bearing minerals, attrited carbon, and carbonaceous material in the ore. Redox potentials were measured with a gold electrode during the conditioning stage prior to flotation. The correlation between flotation recovery and redox potential values could be used to control reagent additions. Treatment of a previously leached and weathered tailings material, averaging about 0.055 ounces of gold per short ton, was also investigated. The tailings were first water leached at approximately 60? C, and the water-leached tailings, containing approximately 0.03 ounces of gold per short ton, were then fed to the column flotation unit. The effects of pH' and sodium sulfide addition on gold flotation recovery and redox potentials were examined. Maximum gold flotation recovery, 36 pct, was achieved at pH 8,5 with a sodium sulfide addition of 0.18 Ib/st. Overall gold recovery by leaching and flotation was in the range of 70 to 80 pet.

Jan 1, 1989

By Andreas Siegmund

During the decade of the nineties the conventional method of primary lead smelting (sinter machine/blast furnace) was successfully challenged by the introduction of novel direct and continuous smelting processes. In combination with a significant shift in market structure, as well as more stringent government regulations these modem technological innovations like the QSL, Kivcet, and Isa/Ausmelt processes became more than major competitors. They have proven to be economically and environmentally viable. The intensification of the metallurgical reaction by applying oxygen enriched or pure oxygen bath or flash smelting principles resulted in cost savings and a higher flexibility with respect to raw materials and additives usage. By synchronizing individual auxiliary plant sections with the smelting process a virtually waste-free production and low-emission mode of operation with nearly optimum energy exploitation is achieved. The primary lead industry will gradually substitute the sinter -blast furnace operation with novel high-energy efficient technologies in the new millennium.

Jan 1, 2003

By William D. Riley

The U. S. Bureau of Mines has developed technology to recover by-product materials from aluminum scrap using engineered scavenger compounds (ESC). ESCs are structural oxides with a channel or tunnel structure that allows them to hold ions of a specitksizes and charges. The scavenging reaction is easily reversible allowing the ESC to be recharged for continued use and the ion is recovered as an electro deposit. Key features of this novel technology are; a) ESC ,systems are designed to have a high degree of selectivity for a desired ionic species. b) The recovered mater.ial requires little or no additional reprocessing prior to reuse. Two current uses for the ESC technology that are described in this paper are the removal and recycle oflithium (Li) from lithium aluminum (Li-AL) alloys; and, using ESCs as a replacement for the conventional demaging (magnesium removal) technology used by the secondary casting industry. Research indicates that the ESC technology proposed for both these applications has either 'distinct economic and/or environmental advantages over previously employed methods of recovering. metal values from aluminum scrap.

Jan 1, 1995

By Alicia E. Ares

316 L Stainless Steel samples were solidified directionally under conditions which produced the columnar to equiaxed transition. The position of the transition was located in each sample and the distance from the bottom of the ingot was measured. During solidification the distribution of temperatures were measured by means of thermocouples located strategically. From the measured temperatures the following parameters were derived; the local temperature gradient, the cooling rate and the velocities of the liquid and solidus fronts. Comparing the location of the transition and the values of these parameters it was found that the temperature gradient reaches negative values of as low as -13.44 "C/cm, and velocities of the fronts of around 0.1 cm/s. Also, a supercooling of 5.81°C were measured which was associated with the supercooling for the nucleation and growth of the equiaxed grains ahead of the columnar front. In addition the primary and secondary dendritic spacing was measured in both regions. The spacing was compared with the predictions from available models. The results are presented and discussed in the frame of the results obtained for other alloys

Jan 1, 2002

By Yong J. Kim, J. M. Park

"Solid/melt interface shape during continuous casting process has a strong influence on the resulting microstructure of the ingot. The interface shape is primarily governed by the heat flow condition between the molten metal and mold (or container). The roll of the microstructural transition resulting from various solid/melt interface shapes is discussed using the Sn-22.6wt%Pb alloy. Three different types of mold such as cold mold, resistantly heated mold, and electromagnetically heated mold were used to generate those interfaces having different curvatures. Experimental measurements of complete temperature profile along the axis and surface of the ingot during downward continuous casting are presented to determine the solid/melt interface geometry. The results provide an explanation of the ingot property with emphasis on microstructure.IntroductionA large scale of continuous casting process of alloys often has a rather deep V channel type of solid/melt interface resulting from a limited heat flow condition. As a result, the deep V type solid/melt interface shape entraps defects such as pores and inclusions and also creates canter segregation. In order to reduce the defects concentration, electromagnetic stirring(EMS) mechanism has been applied to the melt in the channel[l]. Speith and Bungeroth introduced first experimental EMS device to the continuous caster in 1952.[2] Today, with wide ranges of benefit, a large variety of such technique is available. Electromagnetic field on the melt can be divided into three aspects. First, eddy current is induced on the metal surface by alternating magnetic field with high frequency, which results in heating the metal. Second, electromagnetic body force which is generated by the magnetic field and the eddy current reduces the melt pressure on mold or support the melt not to contact with the mold[3,4,5]. This force is used for electromagnetic casting process(EMC). Finally, it causes stirring in the melt. Many research efforts have been done on the EMC process to improve surface quality of slab[6] and control meniscus shape where three phases such as melt, solidified metal, and mold powder coexist[7,8]. However, the eddy current heating effect on the surface of the ingot was less considered. It is worth noting that induced eddy current on the surface of slab melts the solidified shell and thus changes the heat flow condition between the mold and melt. Mold heating effect was first proposed by A. Ohno[9] and its processing conditions were identified in details[ 10, 11]. The so-called Ohno process is based on the fact that by keeping the mold temperature slightly above the melting temperature of the liquid, no grain can be nucleated on the mold wall[12]."

Jan 1, 1998

By D. Van Dooren

The final goal of the research project is to develop a 3D FEM model that is able to predict the kinetics and micro-structural evolution during the bainitic transformation. The input parameters consist of thermodynamic and atomic mobility data obtained from the ThermoCalc and mCTRA databases combined with structural mechanics data extracted from the stress-strain curves of the fcc and bee phases. In this paper the general principles of the model are outlined and some interesting preliminary results are shown and commented. The full implementation of the model has presently not been achieved yet. In the model the bainitic transformation is considered as a sequence of martensitic (re)nucleation and growth of a ferritic subunit followed by the carbon rejection into the surrounding austenite. The (re)nucleation of the subunits will be described through a non-classical martensitic nucleation criterion. Once a nucleus has been activated at a specific location in the material, a full-sized subunit is instantaneously formed through a displacive mechanism. The stress state in the system that arises due to the transformation strain can be calculated by a 3D FEM programming code. Immediately after the formation of the subunit, another 3D FEM programming code calculates the carbon diffusion from the supersaturated ferrite into the surrounding austenite. The resulting stress state and carbon profiles will be used to determine where and when a new subunit will nucleate based on a renucleation criterion. Keywords: Bainitic Transformation, Modeling, Eshelby, Carbon Diffusion

Jan 1, 2003

By W. D. Cho

The slag chemistry in steel processing plays an important role in terms of the removal of impurities including alumina particles. In the present study, the dissolution of solid aluimina particles in CaO-based fluxes at the temperatures between 1450 and 1550 °C has been investigated to determine dissolution kinetics and mechanism. Alumina particles were added directly in the slags and the size of alumina particles was measured as a function of time using optical and scanning electron microscopes. The dissolution rate has also been obtained as a function of Si02, CaF2, MgO and MnO contents in the slags. The diffusion boundary layer between alumina and bulk slag phase has been observed and analyzed using SEM and EDX. In addition, some experiments have been performed for the dissolution of alumina in BaO-based fluxes.

Jan 1, 2003

By Haibin Wang, Baojun Zhao, Xueyi Guo, Zhixiang Cui, Zhi Wang

In conventional copper production, anode copper is produced from concentrate in three furnaces in a process that entails four oxidation steps and one reduction step. Three types of slags are produced that require further treatment to recover copper. Dongying Fangyuan Nonferrous Metals recently developed a simplified process which requires only two custom-designed furnaces instead of the conventional smelting, converting and re fining furnaces. The first furnace continuously produces high-grade matte (>75 wt% Cu) that contains little iron (<2 wt% Fe). The liquid matte is continuously fed to the second furnace, which produces anode copper. The new process signi ficantly reduces the capital and operating costs and increases productivity and environmental sustainability. This paper presents fundamental concepts that enable the simpli fied process to be developed. The detailed operations in Dongying Fangyuan Nonferrous Metals are also described.

Mar 1, 2018

By Emil B. Milosavljevic

The photochemical reactions of cyanide ion induced by light were investigated in the presence or absence of a titanium(IV) oxide semiconductor photocatalyst. The light sources employed were the sun and arrays of either mercury or fluorescent (cool white) lamps. The results obtained verify that cyanide decomposes much faster when TiO2 is present in the solution and that it is first oxidized to cyanate. However, contrary to the previous studies, it is established that cyanide is subsequently further oxidized via nitrite all the way to nitrate irrespective of the light source. As expected, the rates of the oxidation processes decrease with the illumination source utilized in the following order: Hg-lamps > sunlight > fluorescent lamps. As nitrate is a significantly less hazardous contaminant than cyanide, complete photocatalytic oxidation of cyanide to nitrate may be a viable method for decontamination of cyanide wastes. Contrary to previous claims, we find that cyanide is slowly photochemically decomposed even in the absence of TiO2. For example, with the mercury lamps as the light source, in two hours, cyanide concentration decreases to essentially zero; up to 7% was converted to cyanate and the remainder to unidentified products.

Jan 1, 1992

By Lev Levin, Sergei Lesokhin

"The formation of titanium carbide during hot filament assisted carburizing of NiTi alloy was investigated. Phase content and morphology of the diffusion zone were examined by X-ray diffraction, X-ray microanalysis, SEM, and Auger electron spectroscopy. The growth of stable and adherent TiC film was observed. A non-planarity of interphase boundary was noticed. The applicability of the chemical diffusion approach to the analysis of the experimentally observed interface instability is discussed. A criterion, taking into account the influence of growth stresses on the stability of the flat interface, is developed by means of linear perturbation analysis.Introduction.Equiatomic intermetallic NiTi belongs to a class of materials exhibiting the shape-memory effect. The unusual property of this compound promotes its application in many fields, from aerospace technologies to medicine. The relatively high ductility ofNiTi also permits its use as a matrix material in metal-ceramic composites. The objective of this work was to investigate the possible incorporation of a ceramic material (titanium carbide) into NiTi by gas carburizing.Free energy calculations indicate the potential to obtain TiC by carburizing Ni-Ti binary phases. The main obstacle to such a process is the high affinity of titanium to oxygen. At moderate temperatures the formation of TiC is preferable to titanium oxidation only if the partial pressure of oxygen is extremely low [1]. This problem was overcome in this work by the use of hot filament assisted gas carburizing. Due to chemical reactions occurring near the hot filament, the gas mixture, initially consisting of methane and molecular hydrogen, was enriched by atomic hydrogen [2], drastically decreasing the content of free oxygen in the carburizing atmosphere.The second part of this article concerns the theoretical analysis of reasons that lead to the development of the experimentally observed morphology of the diffusion zone. In particular, the influence of the growth stresses on the morphology of an interphase boundary is investigated."

Jan 1, 1996

By Kenneth L. Nash

The control of solubility of waste actinide ions, by conversion to highly insoluble mineral phases has been demonstrated in the laboratory. Actinide metal ions are removed from neutral pH solutions by a combined ion exchange-decomposition-mineralization process based on the application of the naturally-occurring hydrolytically unstable.polyphosphate organic compound phytic acid.

Jan 1, 1999

By Varuzan Kevorkijan

A new method for faster production of functionally graded metal-ceramic laminates is based on reactive pressureless counterflow infiltration/penetration of a ceramic substrate with two different metallic infiltrants. The porous or dense ceramic preform is pressurelessly infiltrated or penetrated from one side by the first metallic infiltrant to the desired cross section of the preform, producing the top layer made up of the solidified infiltrant and the underlayer consisting of reactive infiltrated preform. The partly infiltrated preform is then completely infiltrated starting from the other side by the second metallic infiltrant, in this way fabricating the internal layer, consisting of the ceramic preform infiltrated with the second infiltrant and the bottom layer formed by the solidified second infiltrant. Systems already investigated include carbide, nitride and boride ceramic performs infiltrated with aluminum and magnesium alloys.

Jan 1, 2003

By Kazuhiro Nisizono, Takashi Kuroki, Nobuyuki Mori, Keisaku Ogi

"The improvement of critical current density and mechanical property is essential to the practical application of the superconductive oxides. A solidification technique is developed in this study for the growth of columnar or single Y123 crystal with finely dispersed Y211 and Ag particles through a monotecto-peritectic reaction of Li.(Ba-Cu-Ag-0 rich liquid)+ Y211-+ Y123+Lz(Ag rich liquid). The large solidification rate and temperature gradient can refine the Ag and Y211 particles. But Ag-free region is widely formed along the crystal growth direction in the central part of the Y123 cell. Since this phenomenon occurs because of the cellular growth, it is necessary to narrow Y123 cell width or to grow Y123 crystal with flat freezing interface. By controlling crystal growth direction using a seed crystal, Y123 columnar or single crystal with uniformly dispersed fine Ag particles are obtained. The· behavior of Ag and Y211 particles during the solidification of Y123 crystal is simulated by the peritectic growth model of faceted Y123 crystals.IntroductionY-Ba-Cu-0 superconducting oxide (YBCO) with high critical temperature also has excellent superconducting characteristic under the high magnetic field. The critical current density (Jc) has been enhanced by ·using unidirectional-solidification technique, which can overcome the weak-link problem at grain boundaries and control the crystal orientation and the distribution of Y211 particles which give effective magnetic flux pinning centers in the Yl23 matrix [1-4].In addition to improving superconducting properties, it is necessary to improve mechanical property for the practical application. The silver addition to the melt-textured YBCO superconducting oxide has been reported as the effective method to improve mechanical properties without degrading superconducting properties. Since the material properties are considered to be largely affected by silver particle size, form, dispersion state etc. in the Y123 phase, it is important to control Ag distribution in YBCO/Ag composites. Besides, it is also reported that the silver addition improve the corrosion resistance to the water and CO2 [5,6]. Nishizono et al. [7-9] have reported that the silver distribution in the YBCO/Ag composites is largely affected by the solidification condition, but yet some unclear points are also remained. YBCO has been also fabricated by the zone melting method [10-12], and Furuya et al. [5] and Hirano et al. [13] have reported the fabrication of silver added YBCO composites, but the distribution and behavior of Ag are not investigated in detail"

Jan 1, 2000

By Tom Lewis

This report discusses the evaluation of the ENVIRO-CLEAN PROCESS, a technology developed by Lewis Environmental Services, Inc. for the recovery of metals such as chromium, mercury, copper, cadmium, lead, and zinc from surface and groundwater streams. This new heavy metal removal process (patent-pending) utilizes granular activated carbon with a proprietary conditioning pretreatment to enhance heavy metal adsorption combined with electrolytic metal recovery to produce a saleable metallic product. The process generates no sludge or hazardous waste and the effluent meets EPA limits. A 50 gpm system was installed for recovering hexavalent chromium from a ground water stream at a site located in Fresno, California. The effluent from the activated carbon system was reinjected into the ground water table with the hexavalent chromium concentration < 10 ppb. The system simultaniously removed trichloroethylene (TCE) to concentrations levels < 0.5 ppb. The activated carbon is regenerated off-site and the chromium electrolytically recovered. The full scale system has treated over 5 million gallons of ground water since installation.

Jan 1, 1996