Search Documents

By Liangying Wen, Xuewei Lv, Yuelin Qin, Feng Zhu, Guibao Qiu, Chenguang Bai, Meilong Hu, Shengfu Zhang

"The COREX process is the first reduction ironmaking technology with coal and pure oxygen to get high quality hot metal, which consumes a lot of high quality lump coal and some coke. In order to increase the utilization of fine coal, reduce coke consumption and enhance the competitiveness of the technology, the combustion behavior of pulverized coal injection in melter gasifier is studied experimentally. The results show that the combustion rate of PCI increases with the increase of temperature. And the combustion rate increases with decreasing coal particle size. Compared bituminous coal with anthracite, the former’s burning ratio is higher than the latter in the same granularity. The combustion effect is remarkable when coal blend of bituminous coal and anthracite with the smaller particle size is pulverized in COREX process.IntroductionThe COREX process is the first reduction ironmaking technology with raw coal and pure oxygen to get high quality hot metal, which consumes a lot of high quality lump coal [1-3]. However, the proportion of lump coal in raw coal is very small, and it is avoidless to produce fine coal because of mechanical coal cutter and storage and transportation process, so it is important to resolve utilization of fine coal in COREX ironmaking process in order to energy conservation and reduce the cost of hot metal [4]. Currently, Coal briquetting technology is adopted to utilization of fine coal in COREX process [5], but coal briquetting system has high investment cost and requires feasible adhesive agent. The pulverized coal injection (PCI) into a blast furnace is being used on a global scale to improve the stability and reduce the cost of blast furnace operations [6]. The successful development of PCI in blast furnace is contributed to pulverized coal in COREX melter gasifier. However, it is different in PCI process between COREX melter gasifier and blast furnace, and the differences are as follows: firstly, The air is injected into blast furnace, which temperature is about 1200 ?, but in COREX melter gasifier the normal temperature oxygen is blasted, so PCI in blast furnace begin burning in blowpipe, but the combustion of PCI in COREX melter gasifier is only in raceway. Secondly, the racway of COREX is smaller than that of blast furnace of the same size. So, the combustion behavior of PCI is complex in COREX melter gasifier, which is not use for reference."

Jan 1, 2012

By Tianzu Yang, Xunbo Deng, Weifeng Liu, Lin Chen, Shuai Rao, DUCHAO ZHANG

To overcome the shortcomings of traditional cyanidation process for refractory gold ores, the smelting processes have been proposed. These smelting processes could be divided into two kinds, namely, indirect smelting and direct smelting. In the indirect smelting process, the calcine of refractory gold ores are added in the copper or lead smelting processes during which gold can be enriched into copper matte or crude lead. Then gold is extracted from the anode slimes. In the direct smelting process, refractory gold ores are smelted directly with gold enriched into ferrous matte. Then gold is extracted from ferrous matte. Based on the direct smelting process, the metallurgy-beneficiation united process for refractory gold ores has been proposed. In this process, gold is firstly enriched into ferrous matte by direct smelting, then the grinding-flotation process is used to obtain gold-rich sulfurous iron ore, and finally gold is extracted via hydrometallurgical method.The metallurgy-beneficiation united process has advantages of high gold recovery ratio, environment-friendly and low cost, which provides a new idea for the extraction of gold from refractory gold ores.

Mar 1, 2017

By Akira Yazawa

The continuous converting has attractive advantages, but further experimental studies on the slag are required, when the process is considered thermodynamically. The summarized experimental results, obtained with iron silicate slag and with ferrite slag and results relating to actual operation are described and discussed in this paper. At first, equilibrium relations at controlled oxygen potentials among three melts of silica-saturated iron silicate slag, white metal and copper are investigated. The results obtained for slag agreed with the thermo-dynamical predictions. Namely, to suppress a magnetite separation, the system should be at high temperature; in the case of the S02 gas of 10 kPa, for example, magnetite did not separate from the slag at 1300°C, but at 1250 and 1200°C the slag was saturated with magnetite even at lower SO2 pressure. Copper losses caused by dissolution of its oxide increased with increasing 5O2 pressure, and were slightly lower than those reported in previous papers without the matte phase. When the continuous converting slag does not contain any appreciable amount of silica - in contrast to the conventional smelting slag ferrite slag would form, but there was no published fundamental work on-ferrite slags. Hence, the melting behavior and activities of the system CaO-Cu2O-Fe2O3 have been investigated. The liquidus diagram in nitrogen atmosphere was, constructed using both thermal analysis and quenching method. The low liquidus temperature region without magnetite separation was found in the part of low content of Cu2O in the section Cu2O-CaO-Fe2O3 and Cu2O?Fe2O3¬CaO?Fe2O3. The activity of Cu2O in the system was also measured. Slags, composed-of CaO, Cu2O and Fe2O3, in platinum crucibles were equilibrated at 1250°C and controlled oxygen pressures. After quenching, the-composition of slag and platinum crucible were determined qualitatively. On the thermo-dynamic analysis of the results, iso-activity lines were drawn, and it was shown that the slag in the converting furnace of the Mitsubishi process exists in an adequate region of the composition triangle.

Jan 1, 1976

By Sheng-ping He, Ya-bing Zhang, Qian Wang, Kun-peng Xu

A mass of Al2O3 tends to form during the continuous casting process of high manganese high aluminum steel, and the properties of mould flux and the quality of slab are seriously affected. The dissolution rate of Al2O3 into the CaO–SiO2–MgO–Al2O3–F−−Na2O−Li2O−BaO−B2O3 slag system has been investigated at 1573 K by employing rotating cylinder method. This paper focuses on the effect of Na2O, Li2O, B2O3, F−, Al2O3 contents and (CaO+BaO)/(Al2O3+SiO2) ratio on the dissolution rate. Experimental results show that the dissolution rate increases with increasing Na2O, Li2O, B2O3 contents and decreasing Al2O3 content, among which Li2O has the greatest effect on increasing dissolution rate; the dissolution rate increases with increasing F− content in slag A-1, but decreases with that in slag A-2; the dissolution rate increases with (CaO+BaO)/(Al2O3+SiO2) ratio within the range from 0.91 to 1.31. The dissolution rate of Al2O3 into molten flux is mainly affected by the viscosity of the molten flux and the thermodynamic driving force.

Mar 1, 2018

By T. Langthaler, H. W. Engl, H. Holl, K. L. Schwaha

"The trend towards near net shape casting requires the development of more complex design and control algorithms for continuous casting ""machines in particular with respect to the solidification process.Compared to conventional continuous casting the reduction in casting thickness allows to influence more directly the solidification rate by control variables like surface cooling and/or casting speed.In order to enable the determination of these control variables for a given solidification profile, an algorithm (inverse solidification analysis) has been developed based on nonlinear constrained optimization. The application of the model is illustrated by practical examples ranging from conventional continuous casting to advanced thin slab casting.IntroductionProcess development in the Iron and Steel Industry is directed towards the realization of continuous process sequences. Since the direct linkage of processes imposes some restrictions onto the individual process steps, more complex algorithms are needed for design of equipment and control of operation. In particular the recent trend to reduce casting thickness, i.e. to cast thin slabs, has made the direct coupling of continuous casting and rolling absolutely necessary. The prospective development in strip production is schematically shown in fig. 1."

Jan 1, 1988

By Mike Trovant, Stavros A. Argyropoulos

"A fixed grid numerical model for phase change problems is proposed. The model solves for heat transfer and fluid flow, via the coupled solution of the energy, continuity and momentum equations. In addition, the numerical scheme accounts for temperature varying thermophysical properties and determines the shrinkage profile resulting from phase and density change. Simulations are run to determine the effect of varying model parameters and wall cooling rates on the location and shape of the shrinkage void formation in cylindrical casts. Results are shown for both aluminum and magnesium.IntroductionThe mathematical modeling of phase change processes (be they solidification or melting problems) entails solving for many interrelated phenomena. A comprehensive numerical simulation of the casting of a metal, for example, would have to account for: (a) heat transfer in both the solid and liquid portions of the metal and in the mold, (b) the release of latent heat during phase change, (c) fluid flow behavior in the liquid portion of the metal, (d) temperature induced shrinkage caused by liquid contraction and solidification contraction, and (e) the development of thermal stresses with accompanying shrinkage in the solid portion of the cast and mold. A schematic of the relationships that exist between the coupled equations which govern solidification is shown in Figure 1."

Jan 1, 1994

By Janusz Majta

The aim of this work is to investigate the control of microstructure evolution through variation of particular deformation parameters in the two-phase (intercritical) region. Niobium-microalloyed and low-carbon steels were investigated. A detailed examination of the factors affecting the ferrite microstructures of tested steels indicated that there were distinct advantages of finishing at temperatures in the austenite-ferrite region. The various results of deformation in the two-phase region are presented. Consequently, the influence of the most important process parameters on the microstructure evolution and mechanical response of the material is determined. The prime objective of the realized research work is the determination of relationship between the history of deformation and final product quality i.e. texture and mechanical properties. To reach the objective, the constitutive equations are proposed for modeling the effects of the hot-deformation process occurring in the austenite and austenite-ferrite region of low carbon and microalloyed steels on the mechanical properties of the resulting product. These models link advanced, finite element approaches simulating metal flow and heat transfer during hot-plastic deformation with constitutive equations describing microstructural processes and mechanical properties.

Jan 1, 2003

By Michael A. Markowitz, Alok Singh

"Molecular self-assembly of phospholipids and other amphipathic molecules offers a versatile approach to form self-organized microstructures in various morphologies. Stabilization of microstructures in specific morphologies by polymerization renders them useful for practical applications in areas ranging from controlled release technology to template mediated synthesis of metals. Our efforts are focussed on the development of polymerizable biomembranes derived from phospholipids, their properties and utility e.g., as stable templates for studying chemistry at the lipid interface. Polymerized vesicles formed from mixtures of 1,2-bis(tricosa-1 O,12-diynoyl)-sn-glycero-3-phosphocholine, 1, with corresponding lipids having phosphohydroxyethanol,2, or -hydroxypropanol,3, headgroups have been used in electroless metal plating of vesicle surface with gold utilizing selective binding of Pd(NH3)4 2 + to 2 or 3. The surface bound palladium ion served as catalyst for metalization. Metalization of polymerized vesicles constructed from charge neutral diacetylenic phosphocholine,1, did not occur using this process. The headgroup structure of the negatively charged phospholipids and the degree of vesicle polymerization had an effect on the stability of the vesicles after metalization. Vesicles formed from a mixture of 1 with polymerizable diacetylenic phosphatidic acid, nonpolymerizable 1,2- dipalmitoyl phosphohydroxyethanol or 1,2-diacyl phosphohydroxyethanol (from soy lecithin) were not stable to metalization process. The metal coating of the vesicles was examined by electron diffraction and revealed that the gold metal on vesicles was polycrystalline and face centered cubic. The results demonstrate the utility of polymerized synthetic membranes as template for easy and efficient synthesis of nanoparticles. IntroductionPhospholipids, synthetic or natural, provide a simple and straight forward route to construct membranes in a variety of morphologies due to their inherent property of selforganization in the presence of water[1]. Vesicles are closed spherical structures comprised of concentric walls made from lipid bilayers. Vesicles are morphologically simple structures with enormous technological potential. Polymerizable phospholipids prepared by incorporating a polymerizable group in the molecules demonstrate physical properties comparable to their non-polymerizable counterparts and have the added virtue of providing enhanced physical and chemical stability to the membranes[2,3]. The size, shape and properties of the organized assemblies are dependent on the lipid structure and the nature of the aqueous environment[4,5]. The headgroup geometry, surface charge density, and spatial arrangement of the phospholipids are known to affect the surface behavior of the lipid membranes, which is evident through their interaction with other molecular (hormones, antigens, antibodies etc) or lomc species. Since phospholipid headgroup structure and charge can be modified either synthetically or by chemical perturbation of the aqueous medium (e.g., pH or ionic strength), phospholipid membrane surfaces offer a potential for developing novel strategies in those areas which involve the use of molecular reactive sites. One such strategy which could be envisioned explores the use of molecularly engineered phospholipid assemblies to design and prepare template structures to regulate formation of ordered materials [6]."

Jan 1, 1994

By A. V. Tarasov

In order to improve the efficiency of hydrometallurgical processing of pyrrhotite concentrates, an integrated set of research has been carried out to investigate the use of sulfur dioxide in individual unit operations and as a leaching agent in the autoclave process as a substitute for oxygen. Treating iron-containing raw materials for production of nonferrous metals are based on the selective reaction of SO2 with iron sulfides and oxides. Iron is dissolved as sulfate, which can be treated in a separate circuit to produce iron-containing pigments or it can be disposed of after neutralization. Nonferrous and precious metals contained in pyrrhotite concentrate do not react with sulfur dioxide and remain virtually completely in the solid phase, i.e. high-grade sulfide concentrate to be treated by hydro- or pyrometallurgical methods. Elemental sulfur formed in the process of leaching is separated from the pulp in granulated form as a result of the use of special surfactants. The process of sulfide concentrate leaching with the use of sulfur dioxide is conducted at temperatures above the sulfur melting point (119°C) with distributed feeding of surfactant and under a partial pressure of sulfur dioxide of up to 0.3 to 0.5 MPa.

Jan 1, 2006

By Jorge Alberto Soares Tenório, Amilton Barbosa Botelho Jr, Denise Crocce Romano Espinosa, Mónica M. Jiménez Correa

Wastewater from nickel lateritic process still has valuable metals that could be recovered. Using an ion exchange to recovery these metals, the iron becomes a problem due to the fact that it precipitate at pH 2. The aim of this research was to make iron soluble by reducing Fe+3 to Fe+2. A synthetic solution was prepared with sulfate ferric. The reducing agent sodium dithionite was used and the potential was varied (initial potential: 700, 600, 500, 450 e 400 mV) using as a reference the Pourbaix diagram for iron created by HydroMedusa software. The pH was ranged between 0.5 and 2.5, the reducing agent’s concentration was 0.5 M and the reaction time ranged between 30 and 120 min at room temperature. The ferric iron and total iron concentration were verified using a spectrophotometer with 5-sulfosalicylic acid (SSA) to determine Fe(III) and ammonia to determine Fe(II) and Fe(III) in 500 and 425 nm, respectively. The results indicated that total reduction was at 400 mV in any pH between 0.5 and 2, but less than 40% in pH 2.5 at this potential value.

Mar 1, 2017

By L. L. Sutter

Fly ash is a by-product produced from the combustion of most hels including municipal solid waste. Currently, most combustion residuals are disposed of in landfills at a continually increasing cost and with questionable impact on the environment. Due to the presence of heavy metal compounds, municipal waste combustor (MWC) fly ash has the potential to leach these metals (e.g., lead and cadmium) above regulatory limits. The heterogeneous nature of MWC fly ash makes detailed characterization difficult. This research focuses on the identification of lead compounds in MWC fly ash. Samples obtained from the Olmsted Waste-to-Energy Facility in Rochester, Minnesota were examined in this study. The fly ash was fractionated into six size ranges and prepared as geological thin sections for analysis. The worked discussed in this paper involves using an electron microprobe analyzer to determine phase composition in MWC fly ash. In addition, backscattered electron imaging, digital image processing, and mineral liberation analysis software were used to determine phase distributions and phase associations as a function of particle size. Several lead containing compounds in several forms are identified. The results of this study show that lead can be identified in small sectioned particles which would not be apparent using normal backscattered electron imaging.

Jan 1, 1994

By W. L. Dalmijn, E. A. Schokker, N. Fraunholcz, P. C. Rem

Many processes developed for the mechanical processing of Automotive Shredder Residue (ASR) suffer from high processing costs. We offer a distinct concept for low-cost mechanical processing still allowing high value-added recycling of the recovered materials. The basic idea behind this approach is to produce saleable pre-concentrates at the lowest possible costs that can be further processed in existing separation facilities. Our process includes screening, size reduction and magnetic separation. Preliminary studies showed that fibers in ASR are magnetic due to adhering rust particles allowing separation into a fiber fraction and a non-magnetic rigid fraction by high-intensity magnetic separation. The fiber fraction is most suited for thermal processing. The rigid fraction mainly consists of plastics and rubbers with up to 10 wt.-% of non-ferrous metals, some inert material and copper wires. This fraction is very well suited for mechanical processing by, e.g., sink-float separation in existing metal separation plants. The non-metal fraction can be processed further to recover the plastics and rubbers. The process proposed in this study is expected to be substantially cheaper than full thermal processing. In addition, as it mainly relies on existing separation facilities, it can be applied in the short term.

Jan 1, 2000

By Matthias Frommer, Carl-Peter Reipl, Reinhard Flende

"Today there is a growing demand for strip of superior steels with specifically tailored technological properties. Especially strips of high-strength, micro-alloyed steel grades applied to manufacture longitudinally and spiral-welded pipes are a growth market. Tubes are generally required to have high strength and sufficient toughness values and thus favour specific hot strip microstructures. The correlation of chemical analysis, process parameters and mechanical properties with microstructural features is still a challenging task. During the last decades, scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD) have become useful tools for the characterization of complex microstructures. The EBSD data provides an immense variety of post-processing possibilities, e.g. related to grains, grain boundaries, misorientations or texture. This paper highlights the results of an advanced analysis of microstructures representing industrial produced hot-rolled strips and presents an approach to define and quantify some essential microstructural parameters.IntroductionHigh-strength microalloyed steels have been used for the production of welded pipes for more than 30 years. However, the alloy design of pipeline grades is being continuously modified and the process technology optimized because of the increasing high strength-toughness combination requirement for pipeline steels. Compact strip production (CSP®) technology is an upcoming promising route for the production of high-quality pipeline steel grades [1]."

Jan 1, 2012

By D. A. Milligan

Ammonia leaching of copper sulfide concentrates, matte, scrap or other sources of copper yields copper amnine sulfate solutions which are converted to metal in a two-stage process involving precipitation of inter- mediate sulfites and their thermal decomposition to copper powder of high purity. Processing details and results are given. Considerable simplification in circuitry and cost savings are indicated. Energy requirements are reduced by substitution of copper powder precipitation and ammonium sulfate crystallization for solvent extraction, electrowinning and lime boil.

Jan 1, 1976

By Magdelinka Padenkova-Yaneva, Emilia Christova Kostakeva

"One of the methods for waste treatment is composting during which as a result of controlled biological decomposition of organic waste in aerobic conditions harmless materials are received. Composting takes place in suitably designed premises which ensure the optimal conditions for biochemical decomposition of the waste. A usual way to process composting is the spreading of the waste on a base made from reinforced concrete.In the paper the phases and basic technical features of the process of composting, the requirements and properties of the base and the ways of protection of concrete base against corrosion are revealed. Technical decisions for a specific construction site in Bulgaria are shown and the advantage of achieving durability of the concrete constructions in the plant while achieving simultaneous environment protection from pollution is discussed.IntroductionComposting is the process of controlled biochemical decomposition of vegetable and animal organic waste in aerobic conditions as a result of which harmless materials are obtained. The latter have better stability and are rich in humus substances which are useful for agricultural crops and can be used for restoring the soil fertility [1, 2, 3, 4].In modern waste treatment plants a composting technology is adopted in which the waste is spread on a concrete base as piles with certain dimensions [1, 3]. These piles are periodically stirred or air is blown through them in order to ensure the quantity of oxygen required for the process of aerobic decomposition of the organic matter. The fluids and gases formed in the course of the composting are take away in order not to pollute the environment – air, water, and soils. For this purpose the base on which the waste is spread must satisfy certain requirements, and the gases must be taken away and rendered harmless in order to protect the atmospheric air from pollution. This paper discusses the need for protecting the concrete base from corrosion and characterizes the stages and main parameters of the composting process and the possibilities for primary and secondary protection of the concrete base from corrosion. Specific technical decisions applied in a composting facility in the area of the town of Plovdiv are presented."

Jan 1, 2008

By Petr Stehlík

"This paper is aimed at showing and demonstrating progress in technologies and improvements in units for the thermal processing of various types of waste. The following areas are covered: units for the thermal treatment of hazardous industrial waste and common MSW, technologies for the thermal treatment of industrial and sewage sludge, utilizing waste in cement production (material and energy recovery), up-to-date off-gas cleaning systems, original and unique units for the thermal processing of polluted gases, low-NOx burners. The paper represents a review based on industrial applications, papers published in reputable international journals and a monograph under preparation.IntroductionThe present contribution is an overview of the activities and achievements of the Institute of process and environmental engineering (UPEI) of the Brno University of Technology (VUT). The Institute belongs to European leading teams in the field of the thermal processing of various types of waste. The research in the institute currently revolves mainly around a strategic project “Waste and Biomass Utilization focused on Environment Protection and Energy Generation” that is supported by the national government. Due to the limited space this paper is conceived as a review of papers published especially in reputable international journals.Main (strategic) target of the research is development of new, efficient processes (eventually modernized processes with novel original elements) for effective and highly efficient treatment of waste and biomass, including their maximum utilization as renewable energy sources while minimizing harmful emissions. To this purpose, highly advanced know-how for the design and construction of the related technology lines is being developed, supported by mathematical modeling (see e.g. [1]), experimental validation and optimization.Municipal and Industrial Solid Waste – Concept of Waste-to-Energy CentersThermal processing of various types of wastes is not only waste disposal and/or treatment at present. It has to be regarded as waste to energy process wherever and whenever possible and feasible. This observation was at the origin of the concept of new regional Waste-to-Energy Centers (WTEC), outlined in the following paragraphs. The proposal of the centers is based on a combination of experience, know-how and sophisticated approach. The main fact influencing the concept of WTEC is the necessity to treat different types of wastes. Typical types of wastes as well as main products of the processes in a WTEC are shown in Figure 1."

Jan 1, 2008

By Sung-Joo Lee, Gi-Chon Han, Nam-Il Um, Hee-Chan Cho

"In Korea, almost all of bottom ash produced by coal power plants is disposed of in ash ponds. Ash storage areas comprise more than 80% of most coal power plant sites. This disposal method is causing environmental problems and a managerial burden for plant operators. In this study, investigations to develop a beneficiation process for separating coal pond ash into various products were undertaken. To improve efficiency of the separation, coal ash was separated by sizes and each size fraction was subject to various beneficiation processes. The separation process used were flotation (-200 mesh size), hindered settling (16x200) and tabling (16x200 and 8x16 mesh). The results showed that various marketable products, such as lightweight aggregate, sand, high-carbon fuel, could be recovered from coal pond ash using simple physical separation techniques.IntroductionDue to the increased use of coals every year, about fifty million ton of coals were used in 2007 alone. As a result, about 6 million tons of coal ash were generated. In Korea, the coal bottom ash is classified as a general industrial waste and is usually disposed of in ash ponds. The costs for this disposal method continue to increase due to rising costs of site management and development and more strict environmental regulation. Therefore, utilities are constantly looking for ways to increase utilization of coal ash. In this study, various beneficiation processes were evaluated to examine the possibility of separating coal pond ash into various products which can be used as aggregates and high-carbon fuel."

Jan 1, 2008

By Amanda C. Lima, Luiz Augusto H. Terrones, Sergio N. Monteiro

"Fabric from weaved yarns made of jute fibers have been considered as reinforcement for polymeric composites. In particular, these fabrics obtained from discarded sackcloth are presently being investigated as environmentally friendly composites with recycled polyethylene matrix. The objective of the present work was to compare the practical properties and economical aspects of these composites with those of conventional materials such as wooden board and gypsum panels for building application. The comparison showed that, depending on the amount of post-used jute fabric, a cost/benefit analysis favors these composites over the conventional materials.IntroductionThe increasing amount of wastes generated by human activities is becoming a worldwide problem of pollution with growing consequences to the environment. The question on how to dispose these wastes is, therefore, a major global issue. Among the possibilities of it gating the problem, the use of materials with characteristics of being renewable, biodegradable and recyclable is considered an environmentally correct solution. Examples of this type of materials are left over lignocellulosic fiber from coconut husks and sugarcane bagasse [1] that, after the primary extraction of edible pulp and juices, can be recover for industrial application. Nowadays, the main use of these fibers is to reinforce polymeric composites applied as components for building construction and automobile parts [2,3]. In addition to these applications, composites reinforced with residual lignocellulosic fibers may replace conventional furniture and panels made of wood and thus help to reduce deforestation [4].Environmental protection is not the only motivation for recycling natural fiber wastes. In developing regions activities associate with collecting and processing residual fibers provide job opportunities for low-income people. Moreover, if the lignocellulosic fiber is collected as a recyclable waste, it hes the economic advantage of a comparatively cost, which constitutes in a relevant difference as a choice for commercial utilization."

Jan 1, 2008

By J. Etay, S. Daugan, Y. Fautrelle

"New type of electromagnetic parametric instabilities arising at the free surface of liquid metal in the presence of a low frequency magnetic field are presented. First, the mechanism of the instability is analysed in an idealised case. Then, the experimental device working with mercury is described. Various shapes, both regular and irregular, of free surface are found. A experimental stability diagram is obtained. Measurements of the deformation performed on photographs are compared with physical orders of magnitude.IntroductionWhen a liquid metal pool of electroconductivity a is submitted to an A.C. magnetic field B = B0 cos mt, electrical currents j are induced in the liquid metal and interact with the applied magnetic field to create electromagnetic body forces F = j x B. Those Lorentz forces comprise both a mean value (time average) and an oscillating part. Those forces are widely used in many metallurgical processes to stirr a liquid metal or to control its free surface, e. g., in aluminium continuous casting or electromagnetic levitation problems (1-3). When liquid metal free surfaces are submitted to AC. magnetic fields, the shape of those interfaces may interact with the applied field and leads to a various instabilities. A review of these instabilities may be found in Fautrelle (4). That instabilities may be a problem for the control of processing as electromagnetic levitation or quasi-levitation."

Jan 1, 1999

This symposium is dedicated to the lifetime achievements of Professor H.Y. Sohn. It covers the scientific fields, processing routes and investigation techniques in which Prof. Sohn has worked during his career and is based in the equally important three topical areas: Principles, Technologies, and Industrial practice. Professor Sohn was General Chair of the very first TMS Fall Extraction and Processing Symposium in 1983 in San Francisco which led to the Annual such symposia as this International symposium. Furthermore, the theme of that symposium was sulfide smelting, which is also included in this symposium. [ ] Professor Sohn was born in a beautiful dynastic capital Kaesung, Korea on August 21, 1941. He received his B.S. degree in 1962 from Seoul National University, M.Sc. in 1966 from the University of New Brunswick, Fredericton, N.B., Canada, and his Ph.D. degree in 1970 from theUniversity of California at Berkeley all in Chemical Engineering. After working as a Research Associate at the State University of New York at Buffalo and as a Research Engineer at Du Pont?s Engineering Technology Laboratory, Dr. Sohn joined the Department of Metallurgical Engineering at the University of Utah in 1974 and currently holds the ranks of Professor of Metallurgical Engineering and Adjunct Professor of Chemical Engineering.

Jan 1, 2006