Search Documents

By Z. Smieszek, Z. Szota, P. Gajowski

"A new method for measuring the total quantity of suspensions contained in the electrolyte during copper electrorefining has been developed by the Institute of Non-Ferrous Metals, Gliwice. Electrolyte purity, and the suspensions content in particular, is of essential importance for the quality of electrolytic copper produced during the process. Suspensions contribute to the increase of slime impurities in electrolytic copper and increase losses in noble metals. Up to now, the laboratory method has been used for the· process control which provides analytical results with considerable time delay. Therefore, it is useless for the process control.The measuring method developed enables continuous measurements of a suspensions content directly within the stream of the flowing electrolyte. The principle of measurement is based on changes in optic properties of the electrolyte with varying suspensions content.1. IntroductionIn copper electrorefining, it is essential that the final product quality be maintained. If suspensions are present in electrolyte, the content of slime impurities in electrolytic copper, (such as Pb, Ag, Bi, Sn, Sb, and As), increases which can result in the occurrence of the so-called slime dendrites on cathodes, thus debasing the quality of the product. As a normal suspension content in electrolyte, the contents in the order of several mg/l are considered, usually not more than 5-6 mg/l, while contents exceeding 20 mg/l are referred to as an alarm state. Suspensions present in an electrolyte are usually a light fraction of anodic slime whose main components are metallic silver, lead sulphate, complexes of antimony and arsenic, and sometimes even calcium sulphate; they are mainly composed of very small particles of lead sulphate and antimony complexes. Sometimes - - in case of alarm states - - the so-called ""wandering slims"" can be observed, which are composed mainly of arsenic and antimony complexes. These ""wandering slims"" make a serious technological disturbance. In normal operating conditions of the electrorefining plant, an increase of suspension content can result from such reasons as crack of filter cloth in a slime filter, turbulent flow of the electrolyte, anodic passivation, aeration of the electrolyte, and improper servicing of an electrolytic tank. It is necessary to continuously control the suspensions content in electrolyte for proper electrorefining."

Jan 1, 1989

By Farouk T. Awadalla

The presence of humic species in spent Bayer liquor causes many processing problems in the production of aluminum hydroxide. Ozonation of spent Bayer liquor was found to be an effective process to destroy the colored humic species. The kinetics of the decolorization in spent Bayer liquor was found to be slower than in the alkaline humic acid solution containing no alumina. However, the reaction kinetics ware enhanced by heating the solution during ozonation above room temperature. Copper ions which are used as catalyst to enhance the ozonation reaction were found to be ineffective due to the presence of large quantities of aluminum hydroxide in the liquor. Ozonation was a more favorable process than membrane separation as it achieved about 92% separation of color and produced lower amounts of organic material. The treated spent Bayer liquor can be recycled to the upstream process without causing any difficulties and the purity of aluminum hydroxide product would also be improved. A comparison of preliminary cost data indicated that ozonation compares very favorably with membrane separation in this application. Key words: ozonation, Bayer liquor, aluminum hydroxide, humic species, copper ions, membrane separation, purity and economic.

Jan 1, 1994

By H. Y. Sohn, M. K. McCarter, Bradley C. Paul

"A computer model was constructed for bacterial leaching of the major sulfides found in porphyry deposits, including bornite, chalcocite, chalcopyrite, covellite, cubanite, enargite, native copper, pyrite, and pyrrhotite. The model incorporates equations for the sulfide minerals dispersed in the rock matrix. Leaching occurs by reactions with ferric ion diffusing into the rock fragment: Ferrous ion is resenerated to ferric with oxygen by bacteria at a temperature dependent rate. The model keeps track of the net acid generated, oxygen consumed by the bacterial oxidation of ferrous ion, heat generated, jarosite and hematite precipitated, and copper leached. The model was used to predict the rate of copper recovery, heat generation and oxygen demand for a variety of run-of-mine sized porphyry ores. These results were used in the design of a ventilation system and the economic analysis of a modified in situ extraction method that may be cost competitive with conventional copper production involving open pit mining.IntroductionA study was undertaken at the University of Utah to evaluate the technological and economic feasibility of mining copper by a method referred to as Flood Drain Leach Cell (FDLC) mining. Cells 60 by 75 meters in plan and 70 meters in height are created throughout the ore body by a modified Vertical Retreat Mining technique that includes the removal of 25% swell material. The swell material is leached in finger dumps on the surface while the cells underground are bulkheaded, flooded, drained, and artificially aerated to promote bacterial ferric sulfate leaching. Solutions are cycled through several cells to reach pregnant grade of 1 gram copper per liter of solution. These solutions are then fed to an underground solvent extraction plant and then a surface electrowinning tankhouse."

Jan 1, 1988

By Jiang Diao, Xuan Liu, Tao Zhang, Bing Xie

In the present study, the oxidation process of vanadium and chromium bearing hot metal was investigated by using CaO-FetO-SiO2 slags at 1653K in MoSi2 furnace. The results indicated that both the vanadium distribution LV and chromium distribution LCr were of the orders of 2.2~2.4 with the basicity range of 1.32~1.78 and FeO weight percent range of 28%~45%. Both LV and LCr decreased with increasing basicity and decreasing FeO weight percent. The phosphorus distribution LP was of the order of 1.34~1.56. However, LP increased with increasing basicity and decreasing FeO weight percent. The oxidation ratio values of V and Cr in hot metal were above 84% and the values of P were nearly 50%. In other words, it means the addition of CaO in vanadium slag provided a certain ability of dephosphorization along with keeping high oxidation ratios of V and Cr.

Jan 1, 2015

By Frustino L. Prado

For more than a century, the AAC (ammonia I ammonium carbonate) process has been applied to the recovery of various metals. A variation of it, the Caron Process was first used in the early 1940's in Cuba for the extraction and recovery of nickel from laterites. The original Nicaro plant has been in continuous operation since then. Years later the Caron process was used again in Australia at the Greenvale (Yabulu) NickelICobalt plant, commissioned in 1974. Other projects (Sered, Niquelandia, Nonoc, Punta Gorda, Albania) as well as several studies have been carried out. The Caron Process is alive and still promising. Members of our organization have been working with AAC and the Caron Process since 1952. This paper will review current approaches and potential improvements (enhancement of recoveries of Ni and Co, reduced energy consumption and maintenance simplification). Keywords: Caron Process, Ammonia, Ammonium Carbonate, Laterites, Nickel, Cobalt

Jan 1, 2004

By Lv Guozhi, Niu Liping, Liu Yan, Zhang Zhiqi, He Jicheng, Zhang Ting’an, Dou Zhihe

"CuCr alloy can be extensively used as contact materials in integrated circuit, electrodes, electric contact and high strength conductor. We proposed thermit reduction-electroslag remelting method of preparing the large scale CuCr alloy. But there are pores and oxide inclusions in CuCr alloy prepared by thermit reduction process. This paper studied mainly the effects of ratio of reactant and additive on the inclusion type and their occurrences in CuCr alloy. The slags and CuCr alloy were characterized respectively by XRD and SEM. The results show that when the additive is Na3AlF6, the slag consist of Al2O3 and Cr. When the additive is CaF2, the slag consist of Al2O3, Cr, CaF2 and CaAl4O7. The inclusions in CuCr alloy are mainly Al2O3 and pores which disperse in Cu-rich zone and Cu-Cr phase interface. When 5% CaF2 and 5% KClO3 are added, there are fewer pores and inclusions, and the more better microstructure.1 IntroduceCuCr alloy is the contact terminal material with an eximious properties[1,2], which gradually replaces CuBi alloy becoming the first choice for contact terminal material in the medium and high power vacuum switch after the 1970s. The traditional preparation methods of CuCr alloy mainly contain powder metallurgy, infiltration process and vacuum electric arc melting methods. But the above methods exist some shortcomings, such as poor product quality, high cost of production, processes complex ect[3-9]. CuCr alloy is made by the thermit reduction self-propagating method, which uses CuO, Cr2O3 and Al as raw material to get the high-temperature melt, and then casts to manufacture CuCr alloy ingot, which response equation follows as:"

Jan 1, 2012

By Teruhisa HORITA

The durability of SOFCs is one of the critical issues to realize the SOFC systems. In order to improve the durability, a precise degradation mechanism should be clarified at the different functional ceramic interfaces in SOFC cells and stacks. This paper reviews the improvement of SOFC durability by the mass transport analysis especially at cathode/interlayer/electrolyte interfaces. We have made a precise analysis on the reaction of cathode with impurities. Especially at the (La,Sr)(Co,Fe)O3/CeO2/ZrO2 interfaces, a significant amount of SrCrO4 and SrSO4 were observed at the (La,Sr)(Co,Fe)O3 surface as well as inside the (La,Sr)(Co,Fe)O3 cathode, which suggested some process occurred for both poisoning. Possible degradation mechanisms were proposed based on the observation data.

Jan 1, 2016

By Hartmut Rossel

VAW aluminium AG has built a "Recycling-Technikum" (Recycling Research Centre) to add a new arm to the company's Corporate Research and Development Department. The Recycling Research Centre, a pilot plant for scientific research, has been in operation since September 1993. These state-of-the-art facilities allow the investigation and optimisation of recycling techniques in 'a global way and in detail. Research is concentrated on the unit operations - processing, melting and waste-gas purification - with the available installations making it possible to compare different alternative process combinations on a 100-kg scale. One of the main targets of VAW research is the development of recycling techniques for packaging. The paper presents an approach to recover the aluminium contained in flexible packaging materials using an integrated melting and waste-gas purification system.

Jan 1, 1995

By Rush Kramer

A bulk compositional chemical analysis often provides incomplete information to help the mineral processor when faced with the problem of removing troublesome contaminants in low concentrations. Michigan Tech has developed a unique approach for addressing this problem. A combination of Scanning Electron Microscopy (SEM). Energy Dispersive Spectroscopy (EDS). and image analysis was successfully used to characterize the species responsible for phosphorus contamination of less than .05 weight percent in iron ore. An automated routine acquired the chemical signature of each particle on a backscattered electron image. The few particles containing phosphorus were identified from the hundreds of particles examined. and the phosphate phases present were easily characterized.

Jan 1, 1991

By A. von Röpenack

A forecast of the consequences of our techniques and goods produced, at least a technical assessment will be demanded from us as an industry. The hydrometallurgical winning of zinc is therefore at a crossroads. New processes promise not only better economics, better maintenance of resources and simpler operation, but also more harmony with nature. Pressure leaching promises to eliminate roasting and thus one complete process step. The hematite process solves a difficult and always costly iron problem. HOA opens a possible road to a totally new ,generation of electrolysis. Zinc has a long tradition behind it. Its? importance is as great as ever-. There is still room for new production developments. In my estimation there are good chances for successful new techniques? which will benefit our whole industry. Zinc is a modern and forward-looking metal.

Jan 1, 1990

By Ragnhild E. Aune, Shahid Akhtar, Reza Beheshti

"The potential use of Black Dross (BD) as a raw material for the production of refractories, fluxing agents and glasses is the main motivation of the present study. Heat treatment experiments were carried out in Ar, and under reduced pressure (20 Pa), to evaluate the salt removal efficiency. The chemical composition of the BD after heat treatment was investigated by SEM-EDS and XRD analyses. Based on the present results, it is established that the salt starts to evaporate at ˜1273 K in Ar, and under reduced pressure. The salt removal efficiency in a 20 g sample was found to increase in both cases as a function of time and temperature. Moreover, in Ar the chlorine concentration was lowered to 0.3 wt% after heat treatment at 1523 K for 10 hours. Under reduced pressure, however, 0.2 wt% residual chlorine was obtained after 8 hours at 1473 K.IntroductionIt is believed that aluminum recycling in the near future will become the main route of aluminum production [1]. Black dross (BD) that is produced during this process contains, among other things, high amount of salts like NaCl and KCl [2, 3]. Almost 800,000 tons of BD is annually land filled in United States and this number continues to grow with the increase in aluminum recycling [2]. The BD should be dumped in controlled land field and it is costly procedure [4, 5].The water-soluble compounds in BD react with water or environmental humidity and release chlorides into the water and/or generate toxic gases such as H2, CH4, NH3 and H2 S [6-8]. In the Europe, BD is considered as toxic waste and its disposal as landfill is forbidden [8, 9]. After salt removal, the BD is considered to be non-hazardous and can be buried under ground [10].On the other hand, BD do also contains many relatively valuable compounds that may be changed in to useful materials as a result of further treatment [11, 12]"

Jan 1, 2012

By N. Moelans

A method using an ex-situ electrochemical measurement device was developed to determine the oxygen potential of non-ferrous metallurgical slags. The electrochemical cell consists of the molten slag sample, an inert Ir electrode, a stabilized Zr02 solid electrolyte and a NiINiO reference electrode. Different slags from non-ferrous pyrometallurgical processes were analysed at 1100 and 1200°C and pO2 values between 10-3 and 10.12 bar were obtained. The measurements were evaluated with? thermodynamic calculations and using processing considerations. It was found that the reproducibility and stability of the measurement was significantly improved by shielding the molten slag from the atmosphere by a thin layer of carbon, especially for slags with a low oxygen potential.

Jan 1, 2003

By Mingming Zhang, Ramana G. Reddy

A 3-D mathematical model was developed for the batch reactor of low temperature aluminum electrowinning using ionic liquid electrolytes. This model describes the deposition process by incorporating the mass transport of participating ionic species, homogeneous chemical reactions within the diffusion layer, and the associated electrochemical kinetics. Processing parameters, current and potential distribution, species concentration, fluid flow distribution, and electrode spacing were evaluated for the optimal reactor performance. The results indicated that the electrode spacing significantly affects the electrolyte fluid flow and current density distribution. The parallel electrode configuration (in line with electrolyte inlet) improved the convection and resulted in uniform current density distribution and electrolyte fluid flow. However, for this electrode configuration, electroactive species distribution was most favorable between the electrodes. Perpendicular configuration of electrodes resulted in a more non-uniform fluid flow within electrolyte domain, and it has a potential to cause non-uniform deposits. Aluminum electrowinning experiments were conducted using batch reactor at 80 °C, electrolyte flow rate of 5–20 ml/min, and applied cell voltage of 3–3.5 V. Good agreement was obtained between the model and the batch aluminum electrowinning experimental results.

Mar 1, 2017

By A. V. Tarasov, V. M. Paretsky

"A mathematical model of the low-temperature (soft) nickel oxide reduction (SNOR) in a tubular kiln has been developed including an equation describing changes in the nickel oxide content of the solid material along the length of the kiln; an equation describing the changes in the content of reagents ensuring nickel reduction (i.e., hydrogen and carbon monoxide) in the gas phase along the kiln length; as well as the temperature along the kiln length. The kinetic relationships used for the development of the model had been determined based on experiments conducted specially for this purpose. Model investigations were conducted to determine the distribution of such parameters along the length of the kiln as the contents of metals oxides in the solids, partial pressure of hydrogen and carbon monoxide, variations of the temperature depending on the SNOR process conditions, including the kiln rotation speed. Based on the data obtained, a simplified regression model of the reducing roasting process was developed.IntroductionAt the SeveroNickel complex (Russia) a technology has been developed and is being introduced on a commercial scale for low-temperature (soft) nickel oxide reduction (SNOR) in tubular kilns.The SNOR process has a number of advantages, the main of which are the higher degree of metallization and higher chemical activity of reduced nickel oxide attributable to the lower fusion of the surface of the grains of reduced material due to lower process temperature (800-1000°C) and improved reducing ability of the gaseous phase. However, the fact that the process is conducted in a gaseous phase sets higher requirements to the consistency of its composition necessitating careful continuous monitoring and control of the main process parameters."

Jan 1, 2001

By Shunsuke Yagi

A surface alloying technique was investigated using alternating pulsed electrolysis in an aqueous solution containing a single metal component for the formation of an Fe-Cr layer on an iron substrate. In the process, the iron substrate was dissolved during each anodic polarization of the pulsed electrolysis, providing iron ions in the vicinity of the substrate, while the Fe-Cr alloy was electrodeposited during subsequent cathodic polarizations. A bright, flat, and crack-free Fe-Cr layer with a composition gradient was obtained using a solution containing a trivalent chromium component and a complex forming agent together with some supporting or buffering salts.

Jan 1, 2006

By Atinuke Oladoye, David Esezobor

"Particulate Copper Silicon carbide (Cu-SiCp) composites find application as wear and heat resistant materials in electrical sliding contacts such as in homopolar machines, railway overhead current collector systems where high electrical/thermal conductivity combined with good wear properties is required. However, challenges occur during machining due to the presence of hard reinforcement in the matrix. This may lead to high turnover of tool wear and poor surface finish. The adoption of near-net shape technology to produce such hard-to-machine metal matrix composites and subsequent finish machining with its attendant cost has reported limited success. This paper critically appraises the challenges and opportunities in the improvement of tribological characteristics of particulate Cu-SiC composites and identifies low cost reinforcement material that could be used to improve its tribological characteristics.IntroductionTribology consideration is increasingly becoming a decisive factor in the design and selection of materials for applications involving interacting surfaces in relative motion. The consideration is mainly on the combined effects of friction and lubrication on material's wear integrity and performance amongst other. Annual losses due to tribology in the US industries are estimated at between 1-2% of the Gross National Income [1], in Russia it is about 1-4% of the GDP [2]. Thus, the attributes of tribology has become imperative in modem machinery especially those applications involving sliding and rolling surfaces, and electrical contacts [3- 8].These are readily found in homopolar machines, internal combustion engines, aircraft engines, gears, cams, seals and railway overhead current collector systems [9-12]. In these systems, the dissipation of frictional heat arising from the interacting surfaces as quickly as possible imposes constraints on the choice of materials for such application to prevent softening, plastic and shear flow and the transfer of metal as wear debris onto the interacting surfaces. If these possibilities occur, system performance is compromised and premature failure may result. Materials for these systems are expected to possess high electrical and thermal conductivities, low coefficient of thermal expansion, good corrosion resistance and high melting point [3-8, 13]."

Jan 1, 2011

By Dong-Wei Li, Tao Zhang, Diao Jiang, Zhou Wang

The feasibility of simultaneous vanadium extraction and phosphorus removal from vanadium-containing hot metal was demonstrated with laboratory experimental investigation.The effect of CaO addition on the distribution behavior of vanadium, phosphorus between basic vanadium slag and semi-steel as well as the influence of basicity on the leaching behavior of vanadium, phosphorus was particularly studied. Results show that vanadium oxidation ratio slightly decreases with the increase of basicity, but phosphorus oxidation ratio rapidly increases with the increase of basicity. The leaching of roasted vanadium slag with various CaO contents indicated that the optimal slag basicity for extracting vanadium was 1.5. The maximum leaching efficiency of vanadium could reach 84.02% and the sequence of vanadium leaching efficiency by using different leaching reagents was: 160 g/L Na2CO3 > 100 g/L NaHCO3 > 400 g/L (NH4)2CO3 > 5% H2SO4.

Mar 1, 2017

By Jun Enriquez

Kennecott Utah Copper aims to extend anode furnace campaigns to more than three years. As part of that goal improvements are sought on anode-furnace tuyere-area refractory performance. Kennecott and Praxair developed high pressure nitrogen refining for the Oxidation Stage which shortened anode furnace fire refining cycles by up to two hours per cycle. Future developments include optimizing the Reduction Stage’s steam-gas reforming and achieving coherent jet tuyereless refining.

By Ben Q. Li

An efficient numerical algorithm for solving steady state heat transfer and solidification problems is described. The algorithm is of boundary integral type and is based on the formulation of the field variables along the boundary of the domain of interest. Compared with the familiar domain-based methods, such as the finite element and finite difference (or finite volume) methods, this boundary-based method has an advantage of solving fewer unknowns and hence has a potential for reducing computational time significantly. Another and yet more important advantage of the present algorithm is that it is a stable scheme and is not prone to numerical oscillations resulting from convective effects, as often encountered in the domain-based methods. Therefore, no numerical or artificial diffusion (such as streamline upwinding) is necessary. Numerical examples are presented that are drawn from processing systems for producing aluminum-based materials.

Jan 1, 1994

By R. Padilla

In most of the Chilean copper and gold concentrates, arsenic is present mainly as enargite, Cu3AsS4, which at the conventional roasting or smelting temperatures decomposes liberating arsenic as gaseous compounds. The objective of this investigation was to study the decomposition reaction of enargite in an inert atmosphere in the range of 500 °C - 750°C. The results obtained indicated that the decomposition begins at about 525 °C. Two distinct regions in the temperature dependence of the decomposition rate were observed: a low temperature region between 525 °C to 650°C and a high temperature region between 650 °C to 725 °C. The X-ray diffraction analysis suggests that the decomposition of enargite occurs through the formation of intermediate tenantite, according to the following sequential reactions: 4Cu3AsS4(s) ? Cu12 As4S13(s)+ 3/2S2(g) Cu12 AS4S13(s) ? 6Cu2S(s) + 2As2S3(g) + 1/2S2(g) The decomposition kinetics was analyzed by using the model for a topochemical reaction of spherical particles: 1-(1-X) 1/3 = kt, which represented well the data. Apparent activation energies of 113 kJ/mol and 60.5 kJ/mol were found for the low and high temperature regions, respectively.

Jan 1, 1999