Search Documents

By Donald P. Ziegler, James F. Klausner, Srinivas S. Garimella

"By 2015, nearly half the world's population will live in ""water stressed"" areas. Production of fresh water utilizing waste heat from industrial processes has been identified globally as a research priority.About 15% of the electricity required to produce aluminum is lost as waste heat in the off-gas. However, the low temperature (low grade) of the heat limits reuse. The off-gases contain 50-150 ppm SO2 ; tightening regulations coupled with increasing coke sulfur levels are motivating SO2 control, for which seawater scrubbing is attractive for smelters with suitable access.We describe a process that produces fresh water, utilizing the waste heat while scrubbing SO2 . It uses direct contact between seawater and off-gas to humidify the off-gas. The vapor is subsequently condensed. In smelter trials, a unit treating a slip stream produced high quality water in the anticipated quantity, attaining over 95% SO2 scrubbing. Future work involves scaling the process to be economically attractive.BackgroundPopulation growth, coupled with industrialization and urbanization, are increasing demand for water. Water scarcity already affects every continent. Around 1.2 billion people, or almost one-fifth of the world's population, live in areas of water scarcity, and 500 million people are approaching this situation. By 2025, 1.8 billion people will be living in countries or regions with absolute water scarcity, and two-thirds of the world's population could be living under water stressed conditions (< 1,700 m3 per person annually) [1]. An assessment by the U.S. General Accounting Office revealed that under normal conditions, by 2013, water managers in 36 states in the USA anticipate water shortages, and that the number might grow to 46 states under drought conditions [2].The obvious choice to alleviate water scarcity is the 97% of available water in the oceans, which is saline and requires desalination for use in biological, agricultural and industrial applications. Technologies developed for desalination include Thermal Distillation, Reverse Osmosis (RO), Electro-Dialysis, and Vacuum Freezing. Distillation and RO are the most commercially prominent. Thermal distillation technologies include Multiple Effect Distillation (MED) and Multi-Stage Flashing (MSF). The report commissioned by the World Bank [3] is one of the many excellent references on desalination technologies. According to the International Desalination Association working paper [4], there were more than 17,348 industrial scale desalination plants installed or contracted by 2004. The total production from these plants is on the order of 8.3 billion imperial gallons per day. RO provides 47.2% of the total capacity. The leading thermal process, MSF, provides 36.5% of the total capacity. Although MSF and RO technologies currently provide the most cost effective means for desalination, their drawback is that they are very energy intensive, and whether or not they remain cost effective strongly depends on energy prices and energy supply."

Jan 1, 2012

By Kuo En Chang

Many rare earth - transition metal (RE-TM) compounds absorb/desorb hydrogen reversibly at room temperature and atmospheric pressure. For LaNi5 which is used as a battery material, the electrochemical nature of this process is well known. In the case of Nd-Fe-B which has found wide application as a powerful permanent magnet, the absorption of hydrogen has both significant advantages and disadvantages. However, a fundamental understanding of the hydrogenation process at ambient temperatures and its effect on subsequent corrosion behavior is currently lacking. This paper reports the results of the hydrogenation of NdFeB two alloys, (NdDy)15Fe78.3A10.7B6 and (NdDy)15Fe67Co5V4A12B7, which are compared with that of LaNi5. Results show that hydrogenation can be accomplished by either electrochemical methods or immersion in dilute sulfuric acid. For the latter method, the change in lattice parameter indicates that the level of hydrogen absorbed by the NdFeB particles corresponds fairly closely to an overall composition of Nd2Fe14BH2.7. Cyclic electrochemical charge/discharge experiments show that the maximum hydrogen discharge capacities of the NdFeB, NdFeB-Co-V, and LaNi5 are 40, 60, and 210 mA?h?g-1, respectively. Anodic potentiodynamic polarization measurements and calculated values of icon reveal that absorbed hydrogen in NdFeB-Co-V and the NdFeB may lead to significant increases in corrosion rates.

Jan 1, 1995

By Nathanael Hudson, Ruel A. Overfelt, Sushil H. Bhavnani

"In the aerospace and automotive industries, complex shapes exist which require casting. The problem with these cast parts is the empiricism required to develop the casting process and the accompanying time and expense to develop that process.There has been an interest in using fluidized beds to allow molding sand to better encapsulate the complicated surface geometries of lost foam patterns. Fluidization coupled with a mixing jet helps to homogenize the sand through stirring and may improve the integrity of the casting.At issue is the hydrodynamics of the sand and air around the foam pattern. The commercial package PHOENlCSTM is used to simulate the flow around the pre-casting foam geometry. Employing a two fluid approach, each component is considered a fluid that interpenetrates the other phase. To this end, the kinetic theory of granular 'flow for the sand phase was incorporated into the re-compilable PHOENlCSTM code.The results of this study consist of time-averaged void fraction patterns, with voidage being defined as the fraction of air in the mixture, around the foam pattern submerged in a two-dimensional fluidized bed. The model was benchmarked against past fluidized bed experiments. In order to better understand the dependence of the void fraction pattern around the lost foam pattern, certain physical parameters are varied and the resultant void fraction maps are predicted with the model. Physical parameters such as the aspect ratio of length to width, the placement of the mixing jet, and different mixing jet velocities are varied to illustrate the dependence of the time-averaged void fraction on those variables.Results consistently indicate the presence of channeling around the lost foam pattern, with the extent of the channeling and void formation reliant to a greater degree upon the placement of the mixing jet, and to a lesser degree on mixing jet velocity and aspect ratio.The increase in radial position of the mixing jet from the bed centerline had the desirable effect of granting the churning benefits of a penetrating jet, while at the same time minimizing the formation of excess void fraction at the top of the pattern."

Jan 1, 2001

By M. Cavallini, G. Cannavale, P. P. Milella, A. Pescetelli, C. Lupi

Ni-Cd sealed and vented cells have been widely used in the last few years. The environmental hazard related to the heavy metals contained in Ni-Cd batteries is well known. Therefore, a number of scientific studies and commercial processes have been implemented in order to recycle them. Since spent batteries are a heterogeneous and complex material, any kind of recovery process needs some preliminary treatments. The proposed process described in this paper has been tested in laboratory and further developed in a pilot plant. It consists of a combination of mechanical and hydrometallurgical treatment steps, and is able to treat all type of Ni-Cd batteries. In particular, the mechanical treatments have to be done separately on vented and sealed cells, while the hydrometallurgical step is performed on a mixture of the two products obtained from mechanical steps. A fully automated dismantling line would allow the separate recovery of the plastic or metallic casing, terminals, KOH electrolyte, and electrodes to be further processed· for Ni and Cd recovery. The electrodes coming from dismantling line and sealed batteries are submitted separately to an original crushing and elutriation treatment to separate metallic and active paste in the first case and metallic, plastic and active paste in the second case. The hydrometallurgical treatment is carried out on active paste bearing product to produce Ni, Cd, and Fe comn1ercial salts through acidic leaching followed by a multi-step solvent extraction operation to obtain pure solutions.

Jan 1, 2000

By S. G. Kumar

Experimental studies on high carbon steelmaking through LD Converter - Vacuum Arc Degassing - Bottom Pouring route to produce low oxygen steels were carried out. The results indicated that it is possible to produce steel with a total oxygen content of less than 15 ppm. Thermodynamic and mass balance calculations are made on low-carbon steels that are treated by a complex deoxidation practice based on primary deoxidation of aluminum, manganese and silicon additions; followed by secondary deoxidation of vacuum degassing with simultaneous additions of aluminum. The results showed that primary deoxidation is mainly due to aluminum and the effect of carbon under reduced pressures on deoxidation of molten steel that is already killed by aluminum is negligible. The effect of process parameters on total oxygen content of steel, like carbon content, slag composition and inert gas purging, are discussed.

Jan 1, 1994

By K. Sarveswara Rao

The present paper firstly describes some recent trends from literature on energy management via process intensification to arrive at sustainable technologies for aqueous processing of minerals, metals and materials. Secondly, the energy saving measures practiced in leaching, solid-solution separation, solution purification, metal and material winning and environmental aspects have been discussed. The emerging importance of interdisciplinary nature of hydrometallurgy for practical applications is also highlighted. With the above background, the present paper describes an overview of energy conservation and autoclave processes with a special reference to hydrometallurgical research activities of our Laboratory.

Jan 1, 2008

By Hans von Michaelis

There has been a renaissance in gold and silver extraction and recovery that has taken place over the last fifteen years, since the price of gold was freed from the $3510~ level. Despite major advances in such areas as carbon adsorption processes for gold recovery, refractory gold ore treatment, crushing and grinding, process control, etc., there still remain several gold and silver mineral processing frontiers. Frontiers related to environmental management present significant challenges especially in the USA. More than ever it is appropriate to optimize total economics by adopting a "systems approach" that integrates mining, mineral processing and environmental management.

Jan 1, 1993

By P. R. Khangaonkar

The industry of tin ore mining, beneficiation and smelting gives rise to a number of waste products like the beneficiation plant wastes (called amang), tin smelting slags, refinery dross etc. Some of the wastes deserve treatment to obtain economically useful products or to recover the metal values. The paper describes studies conducted on two materials, viz., struverite-middling (struverite-magnetic tin), which is an intermediate product of beneficiation circuits of tin tailings, and tin-smelting slags. The struverite middling was studied for treatment by chlorination using carbon tetrachloride, so as to yield vapour products separable by convenient condensation. The treatment was also found to lead to a tin-rich product amenable for treatment by known hydrometallurgical routes. The tin smelting slag was studied by alkali-leaching so as to avoid any dissolution of iron and it was possible to obtain an iron-free product solution suitable for high purity tin recovery.

Jan 1, 1996

By Xu Weimin

The existing copper electrorefining tankhouse of Jinchuan Nonferrous Metals Complex (JNC) was commissioned in 1986 for refining blister copper anodes. Blister copper is produced by reverberating chalcocite separated from converter high grade nickel-copper matter by means of flotation. Special chemical analysis of the anodes shows, a composition of 93.02 - 95.72 % copper, 3.0 - 4.96 % nickel and 0.5 - 1.23 % sulfur. The wide range of composition makes the electrorefining process fairly different from others throughout the world. The initial nickel content of 20 ppm and sulfur 40 ppm or more in copper cathodes are reduced to 8.5 ppm and 11 ppm respectively. Since 1986 the tankhouse has undergone significant evolutionary modifications and implementations to ameliorate cathodes quality desirably. The important fact is that the N-additive was utilized through many studies and pilot and field trials successfully. While our primary purpose is to improve chemical quality of the cathodes, tankhouse capacity is increased considerably and the process is perfected satisfactorily. The tankhouse is described with special emphasis on JINCHUAN PROCESS. The upgrading of our product by the utilization of the N-additive is highlighted. The other aspects of the tankhouse including spent electrolyte treatment and by product nickel sulfate manufacturing are briefed as well. Key words: JINCHUAN PROCESS, anode, cathode, electrolyte, electrorefining, N-additive.

Jan 1, 1993

By Yuanbo Zhang, Zhixiong You, FENG ZHOU, Guanghui Li, Zhengwei Yu, Zhiwei Peng

Reduction disintegration of sinter significantly affects the coke consumption and productivity of blast furnace smelting. As we know, the reduction disintegration index (RDI+3.15) of sinter obtained from titanomagnetite concentrate is relatively worse than those from ordinary iron ores. In this study, the effect of sintering parameters, mainly involving coke breeze dosage and basicity on sintering indexes was investigated using titanomagnetite concentrate as raw material in an experimental-scale pot. Subsequently, RDI+3.15 of the sinter was detected according to the Chinese standard of GB/T13242-91. The results show that RDI+3.15 rises with the increase of coke breeze dosage, while it decreases with increasing basicity from 0.5 to 2.0 and then increases in the basicity range of 2.0-3.0. Finally, the microstructure of sinter before and after reduction was studied. And the mechanism of reduction disintegration was preliminary revealed by analyzing the morphologies and distributions of minerals in the sinter.

Jan 1, 2015

By H. Y. Sohn, M. Pérez-Tello, P. J. Smith, K. M. Riihilahti

A three-dimensional computer model for the Kennecott-Outokumpu flash converting process for copper matte is presented. The model incorporates the transport of momentum, heat and mass, and reaction kinetics between the gas and particles in a particle-laden turbulent gas jet. The k-E model is used to describe gas-phase turbulence in an Eulerian framework. The particlephase is treated from a Lagrangian viewpoint which is coupled to the gas phase through the source terms in the Eulerian gas-phase governing equations. Matte particles were represented as Cu2S·yFeSx. Based on experimental observation, the oxidation products were assumed to be Cu2O, CuO, Fe3O4, and SO2. A reaction mechanism involving the external mass transfer of oxygen to the particle surface and diffusion of the oxygen through the oxide layers of CuzO/Fe304 and CuO/Fe3O4 is proposed. Predictions of the mathematical model were compared with the experimental data collected in a large laboratory furnace. A reasonable agreement between the model predictions and the measurements was obtained in terms of fractional conversion of the oxidation reactions and of sulfur remaining in the reacted particles. The simulation of an industrial flash converting furnace was also performed. Higher oxidation rates, more even distribution of particles, and thus a more efficient use of the reactor volume are predicted with a burner having a distributor cone, than with a single-entry burner.

Jan 1, 1999

By S. N. Ojha, Gouthama, R. K. Mandal

"Spray deposition processing of liquid immiscible alloys, based on AI-Pb and Cu-Pb systems have been investigated. Process variables have been optimized to generate uniform dispersion of ultrafine second phase particles in· the matrix of the primary phase. Mechanisms governing the microstructural evolution in this synthesis methodology are discussed. Results of the present investigation are used to demonstrate that rapid solidification of atomized droplets initially provides a high nucleation rate of the second phase during the liquid phase separation. The solid matrix phase nucleates at a later stage and grows with a high velocity enabling trapping of the dispersed phase. Subsequent alteration in the size and size distribution of the second phase is suggested to arise further during deposition of high velocity droplets. Possible reasons for this effect are brought out. Microstructural features of atomized powders and spray-deposits of these alloys are presented to support the present approach of synthesizing composites. IntroductionIn recent years, synthesis of advanced materials with metastable microstructures and ultra fine dispersion of second phase particles has led to the development of novel techniques of materials processing. The other requirement of such a processing methodology is to achieve near-net shape geometries in less number of processing steps. The solidification processing method via spray deposition route qualifies these criteria. This process primarily involves atomization of a melt by high energy gas jets into spray of droplets which are subsequently propelled by the kinetic energy of the gas towards a deposition substrate to build-up a thick high density preform. Although the concept of spray deposition was pioneered by Singer [1] in the early seventies, the fundamentals of the deposition process has been understood only recently [2-4]. Several benefits of spray deposition processing are by now well established [5,6]. Rapid solidification effects are inherent in spray deposition processing due to high heat exchange rate at the droplet-gas interface and also on the deposition surface by force convection. Since considerable heat extraction occurs from the atomized spray prior to droplet consolidation, a relatively low processing temperature is ensured in this process. As a result deleterious coarsening phenomenon can be minimized. In addition, controlled maneuvering of the substrate provides the capability of the process in producing disc, sheet or tube shape preforms of difficult to work materials in a single operation. A significant improvement in properties, resulting from microstructural homogeneity and refinement in grain size induced by spray deposition has been reported for several alloy systems [7,8]."

Jan 1, 1994

The paper describes the propensity of tin to form intermetallic compounds with microalloying elements such as Nb, Ti and aluminium, which are commonly used as additions to achieve particular combination of strength and toughness. Two series of alloys were prepared by arc melting under an argon atmosphere. Each series was based on Fe, Sn and A1 with either Nb or Ti additions. The microstructures were studied using scanning electron microscopy, transmission electron microscopy, energy dispersive X-ray spectroscopy and microprobe analysis. It was found that the level of Nb addition has an effect on the formation of Sn-rich compounds. For small Nb additions, no Sn containing compounds were found, whereas in higher Nb alloy, a Laves phase (FezNb, hexagonal, a = 0.4830 nm and c = 0.7879 nm) containing about 1 at % Sn was found. A FezNb3 phase (cubic, a = 1.1261 nm) associated with the formation of alumina was also found but did not contain tin. No Sn containing compounds were found with Ti additions. The experimental observations have been compared with thermodynamic calculations performed using MTDATA.

Jan 1, 1999

By Riqing Ye

Laser Engineered Net-shaping (LENS TM) is an emerging manufacturing technique that ensures significant reduction of process time between initial design and final components. The fabrication of fully dense parts with appropriate properties using LENS TM process requires an in-depth understanding of the entire thermal behavior of process. In this paper, the thermal behavior during LENSTM processing of 316 stainless steel was studied both numerically and experimentally. Temperature distribution and gradient in the fabricated 316 stainless steel part were obtained by Finite Element Method (FEM) simulation. The numerical results are in good agreement with the experimental observations. The numerical method may be used to optirnize process parameters and predict the thermal response of LENSTM fabricated components. Key words: Laser Engineered Net-shaping, Thermal Behavior, Finite Element Analysis

Jan 1, 2003

"Depletion of known ore reserves and increased demand for precious metals have caused a revolution in biohydrometallurgical processing technology for gold recovery. Known ore deposits and future discoveries are most likely to be lower grade sulfide ores that can be difficult to recover with current leaching technology. Future metal recovery operations will increasingly use bio-oxidation techniques.Bacteria are an integral part of mineral cycling and mineral transformation in nature. Although biological processes are recognized as part of the mineralization and oxidation reactions in some ore deposits, they have only recently been applied to enhancing metal recovery in hydrometallurgical procedures. This paper explores the traditional metallurgical application of biological leaching and oxidation reactions and reviews the complete range of bacteria available for metal recovery systems. Pre-treatment of ores with bacteria improves metal recoveries in tank leaching systems and shows promise for heap leaching methods.IntroductionThere is no longer any question that bacteria playa natural role in the on-going transformation of some ore deposits (1,2). As applied to sulfide ores, a few strains have been specifically identified that exhibit a natural leaching potential (3). These bacteria can be isolated from waters and soils in old mining districts where they contribute to continuing leaching and pollution problems in acid drainage and heavy metal solubilization. Sulfur and iron bacteria as well as many heterotrophic strains have also been found in ore deposits and sedimentary rocks at depths up to 2000 meters (4). Their presence in both ore deposits and processed ores shows the microbial association with natural leaching and the potential role that bacteria can play in the development of new leaching technology."

Jan 1, 1988

By Antti Roine

Sulfidic zinc concentrates are usually roasted in a fluidized bed furnace into sulfur-free oxide form. Metallic zinc is produced from this oxidic calcine using hydrometallurgical leaching, solution purification and electrowinning stages. The roasting step is necessary because zinc oxides are easier to dissolve using traditional leaching methods than zinc sulfides. The Kokkola Zinc smelter uses various types of zinc concentrates and secondary materials as feed mixture. This makes it difficult to find optimum process parameters for the roaster when the composition and particle size distribution of the feed mixture varies even on a daily basis. Certain conditions may even cause difficult accretion problems or increase the amount of calcine in the process off-gas line excessively. A thermochemical heat and material balance model was developed for process advisor, in order to estimate the effects of different process parameters (temperature, process air coefficient, concentrate feed, oxygen enrichment, water feed, etc.) on the heat balance, roasting temperature and calcine composition. This model was constructed using the heat balance module of HSC Chemistry 4.0 software. The prevailing chemical compounds in the concentrate and calcine were verified using mineralogical analyses and equilibrium calculations. The roasting process seems to operate near chemical equilibrium conditions, if the behavior of the main components is considered. This paper describes briefly the basic principles of the calculation model and outlines the results with several diagrams and discussion. The calculated results were in reasonable agreement with the recent process air oxygen enrichment and water feed test campaigns carried out at Kokkola in 1999.

Jan 1, 2000

Hazardous waste has often very complicated chemical compositions in a variety of physical forms and is normally processed in rotary kiln incinerators. Due to large variations in waste types and difficulties in feed characterization, the complex transport processes within the incinerator are not well understood, and the incineration process meets challenges in a smooth operation, and expects various uncertainties in the process chemistry and emission control. For better understanding of the incineration process, simulation was carried out by using Computational Fluid-dynamics (CFD) to characterize temperature and species distribution in the incinerator. In order to catch certain aspects of thermal and chemical behavior, a novel approach is proposed to represent approximately the waste streams and the subsequent combustion process. Hazardous waste in various forms from an industrial-rotary-kiln waste incinerator is firstly converted to a hydrocarbon-based virtual fuel mixture with approximately the same HIC molar ratio and calorific value. The simulation of the combustion process of the simplified hazardous waste was proceeded with a combustion model. The distribution of temperature and chemical species especially the remaining CO in the system is preliminarily investigated. Distribution of CO concentration, as a good indicator of emission level for the incineration process, could be used to evaluate the emission control. The predicted temperature distribution has been compared with available measurement data from an operating rotary kiln waste incinerator at AVR-Chieme, in the Netherlands. Reasonable agreement has been reached between the measured and predicted temperature data. In the next step, measurement of species distribution in the system is planned to further validate the combustion model.

Jan 1, 2003

By C. F. Feng, L. Froyen

"In-situ processes have emerged as new and promising techniques for metal matrix composite fabrication. They offer significant technical and economic advantages over conventional processing. One of the in-situ processing routes that have been used is reactive free sintering of a mixture of powder reactants. However, materials synthesised via this route are always porous because of density differences between reactants and products. An example are the porous Al/(TiB2+Ah03) MMCs obtained by heating powder mixtures of Al+ Ti02+B with Ti02 and B in stoichiometric ratios for forming TiB2• In this study, porous Al/(TiB2+Ah03) composites were further processed by hot-pressing at temperatures above 600°C. This processing cycle was designed so that the composites could be densified. Furthermore, the reaction kinetics of the in-situ processing are studied by means of DSC analysis measured at different heating rates. The activation energies of the three intermediate steps that are involved in the reactive processing for preparing AV(TiB2+Alz03) MMCs are determined to be 923 kJ/mole, 241 kJ/mole and 235 kJ/mole respectively.XRD proved that the hot-pressed products consist of Al, TiB2 and Al203- Properties of the products are assessed by microstructural characterisation (LOM, SEM and EDS), microhardness, Young's modulus and bending tests. The results show that good microstructures, elastic properties and strengths, as well as acceptable ductilities were achieved. For the composition 79.74wt% Al-15.95wt% Ti0z-4.31wt% B, after the reactive free-sintering and hot-pressing cycles, Young's modulus is 105 GPa, bending strength is 509 MPa and maximum strain is 5.0%; for composition 88.73wt% Al-8.87wt% Ti0z-2.40wt% B, they are 89 GPa, 311 MPa and 8.2% respectively. It can be seen that the properties of products can be tailored by adjusting the relative amounts of reactants in green samples. Furthermore, for comparison reasons, Al and a binary system Al-Ti02 were identically processed as the ternary systems. Their microstructures and properties were studied."

Jan 1, 1998

By A. F. Giamei, F. Landis, M. O. Duffy, R. J. Mador

"The directional solidification of complex advanced gas turbine airfoils must be carried out without the nucleation of undesirable grains and with minimal shrinkage. Such problems are typically eliminated by using a number of mold design and process iterations. A more efficient approach is envisioned where a solidification model is generated and utilized to accelerate process development. Towards this end, the directional solidification (DS) of simple geometrical shapes in a crystal grower apparatus has been simulated with MARC finite element nonlinear thermal analyses.The finite element models of cylindrical (2D) and rectangular (3D) cross-section bars in the DS environment are presented. Temperature dependent properties, the impact of latent heat of fusion and a time-dependent radiation boundary condition constitute the more salient features of the MARC models. Solidification zone thermal behavior is predicted during the withdrawal transient for the specific case of nickel based superalloys grown in ceramic shell molds. Comparisons of analytical results with experiments demonstrate notable prediction accuracy. INTRODUCTIONSingle crystal and uni-directional crystal turbine blades require tightly controlled conditions if metallurgically and mechanically acceptable parts are to be produced. Gated blade geometry and process parameters must be precisely determined if incorrect grain structure, orientation and shrinkage are to be avoided. Since purely experimental development programs designed to evaluate these parameters can be excessively costly and time-consuming, an effort combining engineering analysis and verification by experiment has been initiated at Pratt & Whitney. Comparison of analytical predictions and measured data for geometries simpler than a turbine blade, namely cylindrical and rectangular bars, comprised the initial stage of this effort. Subsequent tasks involve modeling geometries of increasing complexity and ultimately the simulation of the directional solidification of the turbine blade, shown schematically in Figure 1. This paper summarizes the results of the initial stage of the effort."

Jan 1, 1986

An EAF dust generated in a Swedish steel mill has been leached in hydrochloric acid at The solution obtained has been subjected to purification by cementation followed by precipitation of zinc with sodium carbonate. The thermal decomposition of the precipitate was studied using thermal analysis and X-ray diffraction. The results show that during the calcination of the precipitate three different reactions occur. The decomposition of the solid phases Zn5(CO3) (OH)6, CaZn(CO3)2 and CaCO3 occur completely at 370°C, 560°C and 940°C respectively, yielding a final product containing 61.9% ZnO and 38.1% CaO. Methods to minimize calcium and manganese in the final product are discussed.

Jan 1, 2003