Search Documents

By E. Fregeau-Wu

The major obstacle in recycling steelmaking slags to the blast furnace is their phosphorus content. Removal of the phosphorus, which is primarily associated with the silicate and phosphate phases, would allow for greater recycle of these slags for their iron, manganese, and lime contents. Calculations show that separation of the silicates from the oxide phases would remove nearly 90% of the phosphorus from the slag. The variable grain size of the as-received slag made liberation by fine grinding difficult. Therefore, slow-cooling experiments were undertaken to improve the grain size distribution. The grain size distributions were determined using in-situ image analysis. The samples were ground to their apparent liberation size and high gradient magnetic separation was used to separate the magnetic oxides from the nonmagnetic silicates and phosphates. Liberation analysis and modeling was performed on selected separation products for discussion of benefication characteristics.

Jan 1, 1995

By Hee Dong Jang

Crystalline metal oxide nanoparticles such as lithium cobalt oxide (LiCoO2) and indium tin oxide (ITO) were synthesized from sprayed droplets of aqueous precursor solution by flame spray pyrolysis. Complete thermal decomposition of the aerosol precursors was obtained at high flame temperature. Molar concentrations of the precursor solution, and the flow rate of combustion gas such as hydrogen, oxygen and air were varied to control particle size, size distribution and crystal structure. The crystalline nanoparticles synthesized were nearly spherical, and their average primary particle diameters ranged from 11 to 35 nm for LiCoO2 and from 8 to 15 nm for ITO.

Jan 1, 2006

By R. L. Nyirenda

One of the problems with ammoniacal-ammonium carbonate leaching of EAF carbon steelmaking flue dust is that zinc present in spinel phases is not leached. This paper presents results of test work in which prior to leaching, EAF dust was reduced with CO containing gas to decompose the spinels into zinc oxide and iron bearing phases, mainly metallic iron and wustite. From such reduction products, the amount of zinc leached increases but the iron co-leached becomes extensive. The effect of various leaching parameters such as liquor concentration and redox potential on zinc and iron dissolution has been investigated. Supplementary experiments utilizing pure zinc oxide and pure iron phases were also carried out. Results show that the co-dissolution of iron from severely reduced EAF dust cannot be prevented. This is because the wustite phase contains zinc which can only be leached when iron also dissolves. Further, the zinc bearing wustite phase is not totally soluble so that the residue cannot be made zinc free. In the absence of air, dissolution of metallic iron hardly occurred, though in leaching experiments of a long duration its transformation to a spinel structure was observed.

Jan 1, 1992

By Jan Petter Maehlen

Solid H-absorbing materials are in focus of ongoing R&D to offer viable solutions for the hydrogen storage and supply systems aimed on use of hydrogen as energy carrier for automotive transportation. Low operating pressures, combined with high gravimetric and volumetric efficiencies, together with fast kinetics of hydrogen release at ambient temperatures (providing conditions for a low energy loss due to decomposition), are the most important features of the ?ideal? H storage material. Hydrides of the light elements are the only possible candidates to build systems with an overall efficiency similar to those accommodating liquid or compressed (700 bar) hydrogen. One promising material from this point of view is aluminium trihydride, alane AlH3 with a gravimetric storage capacity of 10 wt.% H. This work was focused on studies of the crystal structure and thermal decomposition of alane by application of powder synchrotron X-Ray diffraction.

Jan 1, 2006

By P. S. Seryogin

R & D works supported by industrial-scale tests, which were carried out by joint efforts of the OAO Gipronickel Institute and MMC ?Kola? engineers, have accomplished with the production of 90?95% metallized nickel powder in tube furnaces (NPTF), with its ?active fraction? (AF) to be further used for decopperization of nickel electrolyte by cementation. Consistently positive results obtained in the course of the lab and industrial experiments have allowed the Severonickel Combine management to effectively replace all activated nickel powder (ANP), which was then employed for cementation, with the AF, having activity over 80%, and eventually shut down the entire operation of gaseous reduction. Ever since the developed technology has been implemented, its annual economic effect exceeds 2 ml. dollars.

Jan 1, 2006

By F. Tailoka

Microporous membranes have been used to create a very fine dispersion of bubbles which greatly enhances the mass transfer of electroactive species to the electrode. Using this system, it has been shown that it is possible to electrowin copper as a coherent planar deposit, at high current densities, from copper chloride solutions.

Jan 1, 1990

By Krishna Parameswaran

This paper discusses sustainability considerations in primary copper smelting using selected examples of practices at ASARCO LLC, an integrated U.S. primary copper producer. Using the classic Brundtland Commission definition of sustainable development, i.e., “development that meets the needs of the present without compromising the ability of future generations to meet their own needs,” the paper discusses how copper mining and smelting practices can be made sustainable. The examples used to illustrate sustainability considerations include: (1) adoption of flash smelting; (2) emission reduction and process improvement associated with anode refining of blister copper and the converter retrofit project, and (3) preliminary research findings on alkali treatment of copper smelting slags and copper mine tailings.

By Marie-Aline Van Ende, In-ho Jung

A thermodynamic database for the oxyfluoride system CaO-MgO-Al2O3-SiO2-Na2O-K2O-Li2OMnO- FeO-F has been developed based on the critical evaluation and optimization of all available experimental thermodynamic and phase diagram data. The developed database can be used for phase diagram and equilibrium solidification calculations for multicomponent systems and for understanding the solidification behavior of mold fluxes. Based on this thermodynamic database, a simple kinetic model was developed to simulate the interactions between the mold flux and molten steel using effective equilibrium reaction volumes combined with the thermodynamic database.

Jan 1, 2014

By John W. Lund

The Geo-Heat Center has been investigating the utilization of waste silica from the Cerro Prieto geothermal field for several years. The main objectives of the research were to com-bine silica with various additives to (1) form bricks for low cost housing, and (2) to produce a suitable road surfacing material. The various additives that were tested included hydrated lime, portland cement, plastic fibers, asphalt cement and emulsified asphalt. The silica-cement combination produced the strongest bricks and had the best weather resistance, whereas, the silica-lime combination produced the bricks with the lowest thermal conductivity and specific gravity density. The addition of plastic fibers to the silica-lime mixture improved both strength and weather resistance. The combination of asphalt and silica is not suitable as a road surfacing material, however, silica-cement appears promising.

Jan 1, 2006

By Guo-hua Bai, Hong-jing Yuan, Qian Li, Yong-bin Yang, Tao Jiang, Yan Zhang

"The effect of different additives on the bio-oxidation of arsenic-bearing gold ores has been carried out to solve the problems such as long period of leaching, low oxidation rate. The oxidants strengthen the cathodic reaction and thus improve the leaching rate by the increase of electron transfer. Meanwhile, silver catalysis is also effective for the decomposition of arsenicbearing gold ores due to the strengthening of anode reaction. Co-intensification by oxidants and Ag (I) is more efficient to the bio-leaching and the conversion of As (III) because the anode and cathodic reaction of biological oxidation of sulphide ores were both strengthened. The leaching rate reached to 63.94% after bio-leaching 13days by co-intensification of Ag (I) and Fe(III).IntroductionWith the worsening global ecological problems and the gradual exhaustion of available gold resources, metallurgical technology of refractory gold ore has received more and more attention and become possible due to its good advantage of the economic effects and negative effects to the environment. Refractory gold ore, the direct cyanide leaching rate of that is defined as less than 70%, has become an important raw material in gold extraction industry, in which sulfide bearing gold ore represents a large proportion, pyrite and arsenopyrite (FeAsS) is a common gold-bearing mineral. Since the gold is often encapsulated in the crystal lattice of these minerals, destruction or alteration of the ore to liberate the submicron and/or structurally bond gold is necessary[l]. Even if the ultrafine grinding approach also is generally not sufficient for these refractory ores and additional techniques like roasting, pressure oxidation and bacterial oxidation are used to liberate the gold [2]. In the three pretreatment processes, bacterial oxidation is characterized by its new ideas, low cost, no pollution, simple equipment and operation, high leaching index and become the most promising process which has received much attention over time [3-5]. But its further application is limited by some of its own shortcomings, such as long pretreatment time and the toxic effects of arsenic to bacteria on bio-leaching limit."

Jan 1, 2013

By Honglei Zhang, Wuguo Xiang, Xinhao Huang, Guotao Xu, Xilai Chen

"The service behavior of refractories used in hot air pipeline for hot air stoves in a 3200 M3 blast furnace of WISCO was analyzed. The damage factors can be concluded as the poor quality of and alusite based bricks, the severe thermal shock damage, the more porosity in structures, loose bonding capability, and the unreasonable choice of materials and design of bricks. By analysis, the service life of hot air stoves can be enhanced by the measurements such as the reasonable choice of materials and their match, the use of light-weight refractories, the improvement of brick type, etc. Thereafter, the normal production operation of hot air stoves is guaranteed.IntroductionThe No.7 blast furnace of WISCO has been used for about 5 years and it was mid-repaired in March, 2012. The top phenomena of worn hot air pipelines are brick drop, breakage, severely local wear and deformation, existing hidden danger, so the worn hot air pipelines were renewed. Investigations have been done on the stove damage and design [1,2]. In order to clarify the wear mechanism, the used refractories for hot air pipelines were sampled and analyzed, the properties and structures of worn materials and reused materials are relatively studied."

Jan 1, 2013

By Xie Zhang, Jiang Diao, Xin Qiu, Lu Jiang, Bing Xie, Hong-Yi Li

"Duplex converter process, in which the first converter is used for removing phosphorus from hot metal (De-P), is an important way to produce low P-content and ultra-low P-content steels. In order to improve phosphorization removal and formation of slag with high basicity at relatively low temperature during dephosphorization converter process, effects of temperature, silicon content in hot metal and varied compositions of the De-P converter slag on phosphorus distribution between the slag and hot metal were investigated with thermodynamic calculations and by laboratory scale experiments in present work. Results showed that phosphorus distribution ratio between slag and metal was varied in 10.6~26.6 when basicity of the slag was in the range of 1.5~2.1 at 1370, and the distribution ratio was increased with increasing basicity and Fe10 content in the slag.IntroductionIt is known that phosphorus exists in steel in the form of solid solution, which can significantly improve strength and hardness of steel at room temperature. However, the plasticity and toughness of steel, especially the low temperature plasticity is sharply reduced and leads to high ductile-brittle transition temperature. This phenomenon is commonly known as cold brittleness of steel [1~3]. Hence, phosphorus should be removed as much as possible in the steelmaking process, because it is generally harmful to the iron and steel products."

Jan 1, 2013

By Yuanbo Zhang, Guanghui Li, Zhenyu Fan, Tao Jiang, Xiaohui Fan

"Iron ore sintering process is the main source of SO2 generated in the steel industry, of which the discharge amount of SO2 emission accounts for about 60% of the total. Aiming at the features of sintering flue gases and existing problems during the flue gas desulphurization, a technical route of flue gas circulation sintering (FGCS) for iron ores has been put forward. Under the simulated experimental conditions, effects of FGCS process on the main output and quality indexes and SO2 emission rule are researched using simulating flue gases. Compared the novel FGCS with conventional sintering process, SO2 in the final sintering flue gas is obviously enriched and the total exhaust gases can be reduced evidently. The decreasing of oxygen content in circulating gases has bad effect on the sintering indexes. Increasing the oxygen potential is beneficial to obtain high quality sinters. This investigation shows that the FGCS process is promising.IntroductionSteel is a kind of essential material for modern society, but steel-making process is characterized by high energy-consumption and emission as well as heavy environmental pollution. Chinese steel industry has developed rapidly in the last decade, and the environmental problem caused by ironmaking and steelmaking have also aroused the greatest concern, especially the atmospheric pollution caused by SO2, CO2, etc. Iron ore sintering process is the main source of SO2 generated in the steel industry, of which the discharge amount of SO2 emission accounts for about 60 % of the total. The development of the desulfurization process for sintering flue gases to reduce SO2 emission in sintering process is not only the requirements of sustainable development but also the most important environmental tasks for steel industry [1-5]."

Jan 1, 2011

By Ahmad-Bitar¸ Riyad N., Shadia J. Ikhmayies

"CdSi-xTex thin films with O<x<0.3 were prepared on glass substrates by the annealing of CdS:In thin films produced by the spray pyrolysis technique. The annealing was performed in nitrogen atmosphere at 400 --,C in the presence of Te vapor. The compositions of the films were determined by energy dispersive X-ray detection (EDAX) measurements. Scanning electron microscopy (SEM) was used to investigate the morphology of the films. The transmittance of the films was measured at room temperature in the wavelength range 400-1100 nm and used to produce the absorbance of the films. The first derivative of the absorbance was used to estimate the optical bandgap energy Eg by using the minima in the first derivative. The relation between the bandgap energy and the fraction x was found to fit with a parabola and bandgaps in the range 2.196: =Eg: =2.480 e V were obtained. Urbach tailing in the bandgap was also investigated.IntroductionPolycrystalline thin film CdS/CdTe solar cells are promising candidates for low cost and high efficiency photovoltaic applications. The fabrication process of these cells involves the deposition of a p-type CdTe absorber layer on top of an n-type CdS one which acts as a window. The efficiency of the solar cell is affected by the method of preparation of both layers [1, 2].Interdiffusion processes taking place at the CdS/CdTe interface have largely been realized to significantly affect the device performance [3] by changing the bandgap of both CdTe and CdS which modifies the spectral response of the solar cell [ 4]. The formation of a mixed crystal or a graded layer causes a reduction in the lattice mismatch at the CdS/CdTe junction [5] which is about 9% [ 6] and then a reduction in the number of interfacial states and recombination centers, thus enhancing the solar cell performance [7, 8]. A complete understanding of the properties of the intermixed layers CdSxTe1-x that usually constitutes the interfacial region in the CdS/CdTe solar cell is essential. According to our knowledge, a lot of research was devoted to the investigation of the diffusion of S into CdTe [3-5, 9]; but little on the direct investigation of the diffusion of Te into CdS [6]."

Jan 1, 2011

By Baozhong Ma, Yonglu Zhang, Yongqiang Yang, Chengyan Wang, Yongqiang Chen

During the past decades, slurry electrolysis (SE) has been implemented commercially for the processing of bismuthinite and complex Pb-Cu bearing gold concentrates. Recently, SE was proven effective for the treatment of As-rich antimonic gold concentrates. Laboratory test results suggest over 98% of the antimony was extracted, while the extraction of arsenic and gold was less than 0.5%, and that of iron was less than 6%. Moreover, the cathode antimony contained over 98% antimony and less than 0.3% arsenic. Considering the disadvantages of traditional 3 kA slurry electrolysis baths, such as smaller electrode area, reduced capacity, and greater electrode deterioration, the authors have developed an innovative 12 kA slurry electrolysis bath equipped with mesh and fence type titanium alloy electrodes. Furthermore, the technique was successfully used within a pilot scale plant yielding results similar to those observed in the laboratory. The technique yielded ametallic antimony ingot of 99.9% purity after arsenic removal via the addition of Na2CO3.

Jan 1, 2014

By Tiejun Chun, Jian Pan, Deqing Zhu, Vinicius Mendes

"Fine manganese fines are characterized by large amount and low price compared to lump manganese ores. However, fine manganese must be agglomerated as EAF (electric arc furnace) feed. In this paper, high quality fired pellets were produced by simulating grate-kiln process to supply the feed for EAF from some imported manganese ore fines containing high combined water. Manganese ore fines assaying 44.47wt%Mn, 5.89wt%Fe, 12.09%LOI and with 72.7wt% ranging between 0.5mm and 8mm, are pretreated up to the particle size of 84.7wt% passing 0.074mm by HPGR (high press grinding roller) twice in open circuit. The finely ground manganese fines were mixed with 1.2wt% bentonite, balled at 15% moisture for 7min in disc pelletizer. The drop numbers, compressive strength and thermal shock temperature of green balls reach 11 times/0.5m, 11 N/pellet and 360oC, respectively. After the green balls drying in the oven, the dry pellets were preheated at 1050oC for 12 min and then fired at 1300oC for 12 min in electric tube furnace. The compressive strength of fired pellets reaches 2621 N/pellet. Therefore, these pellets are high quality burden for blast furnace or EAF due to high mechanical strength and high Mn grade of 49.11wt% and low detrimental elements.IntroductionManganese, mainly using as deoxidizing agent, desulfurization agent and alloying elements, is widely used in the steel company. With the rapid development of iron and steel industry in China, domestic manganese ores cannot meet the requirement, resulting large quantities manganese ores import to China [1-4]. Compared to lump manganese ores, fine manganese ores containing high combined water are characterized by large amount and low price. However, they must be agglomerated as EAF (electric arc furnace) feed. There are three ways to agglomerate the manganese fine ores, sintering, briquetting and pelletizing [5-6]. Compared to the other two methods, pelletizing technology possesses the following superiorities, such as uniform size distribution of product, stabilizing chemical composition of product and lower energy consumption in producing. Therefore, pelletizing is a superior way to treat the fine manganese ores [7]. The systematic research of producing manganese oxide pellets by fine manganese ores containing high combined water was studied in this paper."

Jan 1, 2011

By Gaballah I.

Elimination of arsenic, mercury and zinc from synthetic solutions containing H;\A.sD4. HgCI2 and ZnCI2 using modified barks was investigated. The pH range was varied from ?1 to 10. The initial concentrations of individual element were 10,100 and 1000 ppm. More than 99 % of mercury and 65 % of zinc cations were removed by the modified bark .. In this case, the modified bark reacts as a cation exchanger leading to the release of &apos; two protons for every HgII or ZnII fixed by this material. About 30 % of arsenic was eliminated from the solution. This &apos;low efficiency could be attributed to? the presence of arsenic ,as. anion. Decontamination of a treated industrial effluent containing 4 ppm of ion? metals was performed on a pilot plant scale by the modified bll(k. More than 70&apos;% of these ion metals were eliminated.

Jan 1, 1995

By Edwin Adoyi Ali, Zainab Shehu Aliyu, Adele Dzikwi Garkida, Muhammad Dauda

Feldspar from Matari, Nigeria was analyzed using SEM, XRD and XRF techniques for microstructural analysis, mineral phase analysis and chemical composition analysis respectively. Qualitative and quantitative XRD analyses revealed the presence of microcline 59.6%, albite 34.7% and quartz 5.71%. The XRF results showed that the feldspar contains 67.32% SiO2, 17.54% Al2O3, 11.33% K2O, 2.75% Na2O, 0.12% CaO, 0.01% MgO, 0.02% MnO2, 0.10% Fe2O3, 0.00% Ti2O, etc and 0.14% LOI. SEM/EDX analysis shows the presence of microcline feldspar as the dominant phase, exhibiting lamellar twinning. The XRD has also revealed that potash has the highest peak, indicating its high concentration. The 0.10% Fe2O3 present is within the permissible level (0.1-0.3%) for glass making and also within the potash feldspar specifications (0.17%). The Matari feldspar is a microcline type, rich in potash, alumina and silica, enabling it meet the standard specifications for alumino-silicate glass.

Jan 1, 2015

By Markus A. Reuter, Jacob Wood, Robert Matusewicz

Over the last 20 years, significant improvements in copper smelter productivity have been realized through the advent of continuous smelting processes. This progress has until recently however, not been carried through to copper converting. Peirce-Smith converting has been widely used by the copper industry for 100 years but is limited by its batch nature in achieving large scale of production. A logical next step is therefore copper converting on a continuous basis with its inherent environmental benefits. A number of continuous converting technologies are currently in use or being developed within the copper industry, the majority of these operating with calcium-ferrite slags. A notable exception however is the Ausmelt Continuous Copper Converting (C3) technology which has focused on operation with ferrous-calciumsilicate or loosely called olivine type slags. This paper discusses the merits of the Ausmelt C3 process and the advantages offered in terms of operational flexibility and process control arising from the use of lime modified iron silicate slags. It also examines the effects of key process variables pertinent to continuous copper converting from both a theoretical and experimental/operational perspective.

Jan 1, 2009

By Lu Lin, Yanping Bao, Xiang Li, Linzhu Wang, Xiaobai Yan

The results showed the microinclusions were mainly Al2O3 and sulfide inclusions from tapping to the beginning of LF refining. Al2O3 inclusions were modificated into calcium aluminates after calcium treatment. Lots of spherical calcium aluminates composite inclusions containing MgO, TiO2 and MnS were found after soft blowing and during tundish metallurgy and left in the slab which caused the defects of beam plates. Pure Al2O3 inclusions were observed again after soft blowing 8min. Average sulfur content in inclusions decreased because of the high desulfurization ability of refining slag. Average Ca/Al ratio value in inclusions increased during LF refinging because of the reduction of CaO in slag by carbon and it increased obviously during the process of soft blowing 8min because of the dissolusion of calcium wire.

Jan 1, 2015