Search Documents

By J. A. Brierley, S. N. McIntosh, C. L. Brierley, E. G. Baglin, E. G. Noble, D. L. Lampshire

The U.S. Bureau of Mines investigated column bioleaching as a means of recovering manganese from a domestic low-grade oxide ore. Manganese was solubilized from the ore using indigenous heterotrophic microorganisms and molasses as the nutrient source. The effects of medium flow rate, molasses concentration, and frequency of medium replacement on the rate of manganese extraction were examined. Results showed that flow rates between 0.4 and 8.1 L/min/m2 had little impact on manganese extraction, while an increase in the total amount of molasses applied during leaching directly affected the extent and rate of manganese extraction. Manganese extractions of more than 90% were achieved in 12 weeks of bioleaching in column tests using 500 g charges of ore. Sugar utilization by the microorganisms and formation of organic acid metabolites were monitored by high performance liquid chromatography (HPLC). Two methods were evaluated to recover manganese from the sugar- depleted bioleaching medium: (1) adsorption onto weak cation exchange resin, followed by stripping and precipitation techniques; and (2) direct precipitation of the manganese as MnCO, using ammonium carbonate. Both recovery methods removed at least 95% of the solubilized manganese from the medium as a carbonate salt. The stripped molasses medium was replenished with fresh molasses and recycled back through the bioleach column, successfully leaching more manganese.

Jan 1, 1993

Jurist, educator and historian Neil Reynolds will be the keynote speaker at the National Mining Hall of Fame's 11th annual induction banquet on Sunday, Oct. 11,1998 at the Pointe Hilton Resort in Phoenix, AZ. Reynolds is Municipal Court Judge for the City of Leadville, CO, home of the National Mining Hall of Fame & Museum, and a fifth-generation resident of the community. His family staked mining claims on nearby Mount Massive in 1862. Judge Reynolds is a fulltime faculty member at Colorado Mountain College, Chairman of the Lake County Historic Preservation Advisory Board and practices law in Leadville. In announcing the speaker, Board Chairman Richard Moolick said seven inductees into the National Mining Hall of Fame will join 138 mining greats previously honored in the annual ceremonies. This year's inductees will be enshrined by Thomas Falkie, president and chief executive officer of Berwind Natural Resources of Philadelphia, PA. Moolick also announced that Jeffrey Clevenger will be the master of ceremonies for the induction banquet. Clevenger is executive vice president of Cyprus Amax Minerals, Englewood, CO and president of Cyprus Climax Metals, Tempe, AZ. A cocktail reception at 6:30 p.m. will precede the black-tie (optional) dinner, to begin at 7:30 p.m. For additional information, contact Esther Mellott at 719 486 1229. Here are the biographies, then, of this year's seven inductees to the National Mining Hall of Fame & Museum.

Jan 1, 1998

By Malcolm J. McPherson

Mine shafts that are used as primary ventilation routes are different in their airflow characteristics to other subsurface openings because of the aerodynamic effects of guide rails, buntons, pipes, cables, ropes, and shape, size and velocity of conveyances. As many shafts contribute heavily to the overall resistance of a mine ventilation circuit, it is important to be able to predict the resistance of a planned shaft with reasonable accuracy. This paper describes part of a study on the ventilation characteristics of hoisting shafts, conducted for the Basalt (Nuclear) Waste Isolation Program (BWIP). Methods of quantifying each of the four components of shaft resistance are developed; namely the shaft walls, fittings (buntons, pipes, etc.), the skips or conveyances, including the dynamic effects of their motion, and shaft stations. Practical guidance is given on ways of reducing the shaft resistance. The paper concludes by giving a step by step procedure for the ventilation aspects involved in the design of combined hoisting/ventilation shafts.

Jan 1, 1987

Introduction The art of ripping has been around since the Romans built the Appian Way, but only in the last decade has ripping emerged as a close competitor with drilling and blasting in breaking up heavy rock formations. That is not to say ripping is as effective in every case, or even applicable in all cases, but it does provide a cost efficient option in many situations-if the optimum ripping techniques are used. Originally designed only to loosen hard pan, the ripper has evolved into a powerful tool, its capability increasing as the weight and horsepower of tractors increased. The tractor-mounted ripper extended the range of ripping because of the additional weight it brought to bear on the ripper tooth. Tandem ripping added the weight and power of a second tractor, extending the rippability range even further. Of course, the use of ripping depends on the type of material to be ripped. Not all rock can be ripped. Determination of rippability-an art in itself-is often inconclusive but there are certain universal principles that can be considered in the first step toward optimizing ripping techniques. Each of the three basic rock types, igneous, sedimentary, and metamorphic, exhibits characteristics that bear on rippability. Igneous rocks are the most difficult to rip because they lack the stratification and cleavage planes essential to ripping hard rock. Sedimentary rocks are generally the most easily ripped since they are built of layers differing in material, texture, color, and thickness. Metamorphic rocks vary in rippability with degree of lamination or cleavage caused by transformation from pre-existing rock. The condition of rock also affects its rippability. Although sedimentary rocks offer the best opportunity to rip and igneous and metamorphic the least, decomposed granite and other weathered igneous and metamorphic rock often can be ripped economically. Little or no trouble is encountered with hardpan, clays, shales, or cemented gravel. Likewise, highly stratified or laminated rocks offer good possibilities for ripping. However, thicklybedded rock formations generally must be drilled and blasted. The physical characteristics that favor ripping may be summarized as follows: • Fractures, faults, and planes of weakness of any kind; • Weathering, resulting from temperature and moisture changes; • Brittleness and crystalline nature; • High degree of stratification or lamination; • Large grain size; • Moisture permeated clay, shale, and rock formations; and • Low compressive strength. Ripper Types A second fundamental to optimal ripping is choosing the right equipment for a particular job. There are three types of rippers-the hinge, the parallelogram, and the adjustable parallelogram. In the hinge ripper the linkage carrying the beam and shank pivots on a fixed point at the rear of the tractor. The resulting arc from up and down movement causes up to 30° differential in the tip-ground angle. Thus, the tooth angle changes as it enters and proceeds to ripping depth. The parallelogram ripper's linkage maintains the same tip-ground angle regardless of tooth depth. This type of ripper has advantages over the hinge-type when ripping above maximum depth, but does not provide the aggressive tooth angle necessary for hard-to-penetrate materials. The adjustable parallelogram combines the benefits of both the hinge and the parallelogram rippers. It has the additional benefit of being able to vary the tip angle to the optimum angle of penetration. It can also be adjusted while moving, for the optimum ripping angle in any material. Several other factors that are important in selecting the right ripping equipment are down pressure available at the tip of the ripper, tractor flywheel horsepower, and the tractor's gross weight. Down pressure at the tip determines whether ripper penetration can be obtained and maintained. Flywheel horsepower rating determines whether the tractor has the power to advance the tip. The tractor's gross weight determines whether the tractor will have sufficient- to use the horsepower. The best ripping procedure depends on the job's actual conditions. While conditions, vary, it is still possible to apply certain proven techniques to a typical ripping situation. Caterpillar Tractor Co.'s Handbook on Ripping says optimum ripping efficiency can be realized if-before actual ripping begins-these questions and answers are considered.

Jan 1, 1983

By S. G. Hardcastle, Akbar Sheikh

In Canadian underground uranium mines, bacterial leaching is being increasingly applied to low-grade ore reserves. At Denison Mines Limited uranium operations, old stopes are used as leaching vessels; these contain a leaching muck pile brought down by drilling and blasting from the back which contained a low-grade reef. The bacteria used require atmospheric oxygen to oxidize the pyritic ore. A study was initiated to evaluate the ventilation, including oxygen supply, specifically, of flood leaching stopes during their rest period. The method of ventilation investigated was a single ended compressed air system which feeds airlines laid under the muckpile and carried through the inlet pressure bulkhead. The air delivery system was tested for post- blast integrity with a sulphur hexafluoride, SF6, tracer gas technique. This was injected into the intake compressed air line and collected at the stope's borehole exhaust in grab-sampling bags. The samples were analyzed with a laboratory gas chromatograph and results provided information on the stope's airflow, average residence time, overall clearance time, volume of the airpath and the airflow distribution. The borehole exhaust was monitored by anemometer and psychrometer and indicated that the psychrometric conditions in the stope were independent of the area's ambient climate. Evaluation of the exhaust's standard gaseous composition showed the oxygen consumption of the bacteria to be independent of the investigated flow range. Field derived results are compared with computer models, theoretical predictions and laboratory investigations.

Jan 1, 1987

By G. P. Hand

The graphite industry as a whole has gone through many changes over the years. Most of the graphite used in major applications since the turn of the century were basic natural or electrode by-product synthetic materials, processed using simple crushing, screening, or grinding techniques. In the mid 1970's new thermal technology was developed which changed the face of the .graphite industry, and opened up a panacea of new products and capabilities. Materials produced through this new technology have helped revolutionize new products and processes in industries including automotive, batteries, fuel cells, electronics, iron, lubricants and steel. This paper outlines the continued improvements in those industries as well as the as well as the outlook for new technology in this rapidly changing area.

Jan 1, 1997

By Paul J. Henkels

Synthetic gypsum is the calcium sulfate co-product of a number of industrial processes. Synthetic gypsum utilization as an alternative to the naturally occurring mineral continues to grow in the gypsum industry. In particular, flue gas desulfurization (FGD) gypsum produced by the electrical utility industry has had a significant impact and a far-reaching effect on the gypsum wallboard manufacturing industry. This paper will discuss the various synthetic gypsum sources verses natural gypsum and highlight issues of use in gypsum wallboard and related products.

Jan 1, 1999

By James J. Brady

The basic story at Bear Swamp was how to excavate an underground chamber 79 feet wide by 227 feet long and 150 feet high, along with the related access, tarbrace, leads, power tunnels and shafts, do it under cost and ahead of schedule and still have just about everybody love you. The isometric sketch of the overall project follows. I won't go into any of the details of the physical scope at this point. Instead, we'll bring out the sizes, grades, particular problems of the different areas as we cover them. First of all, let's establish that Bear Swamp was a Target Estimate - Fee with Incentives type of contract. Gates and Fox's contract was with the project's general contractor, J. A. Jones. We were one of three contractors who submitted proposals and estimates to Jones. After much negotiation and many submittals, Gates and Fox was notified we had been selected to do the underground excavation on April 12, 1971. We had our first people back on site in two days, set up a temporary office, made our first steel order for jumbo erection, pacing our jumbo construction to meet the date when J. A. Jones would have the access portal ready for us. The shops, yards, dry house, compressor building were all erected as sites were designated for our use. At last, on Thursday, June 3, we trimmed the face and moved our 9-machine Euclid jumbo up a hastily constructed haul road and started our portal preparation of the access tunnel.

Jan 1, 1974

By Marcel Haffen, Jean Janin

The purpose of grouting is to modify the permeability and strength characteristics of the subsoil in such a way that the planned structure can be efficiently constructed at a given location. This technique, which originally underwent considerable development in the field of dams construction is constantly evolving and it becomes more and more important in urban zones of intensive underground development for projects such as transport tunnels, stations, car parks, ect. Grouting becomes more and more indispensable whatever the natural characteristics of that subsoil ; such is the case particularly when the planned work runs through cohesionless granular soils, usually water-bearing such as alluvium, sands, disturbed ground, fill material, etc. The selection of the grouting method and the extent of treatment required at depends on two fundamental factors. 1º) nature and behaviour of subsoil to be treated. There is no need to stress the necessary of a good knowledge of geotechnical, hydrological and chemical characteristics of the ground to be treated. At the present time the specialists in these fields have available numerous methods of analysis, either laboratory or field tests, which enable to evolve a suitable treatment.

Jan 1, 1997

By J. W. Langhans, B. D. Blake

The U. S. Bureau of Mines has been investigating the application of thiosulfate to recover gold directly from low grade refractory carbonaceous ores for the past four years. Statistical experimental methods were used to determine the effects of various leaching parameters on both gold extraction and thiosulfate consumption. Seven variables were investigated, including thiosulfate, copper, ammonia, sulfite, and sulfate concentrations, leaching time, and leaching atmosphere. This information was used in face-centered cubic (FCC) surface response experiments to define the optimum leaching conditions for a low grade ore. Two models were generated from the data to predict gold extraction and thiosulfate consumption as a function of the leaching parameters. The models predicted a gold extraction of 67 pct and reagent consumption of 2 kg [S2032/mt ore at 0.25 M S2032-, 0.0014 M Cu2+, 0.27 M NH,OH, 0.00625 M SO;-,] and leaching for 16 h. Actual tests resulted in 62 pct gold extraction with 0.93 kg S2032- consumed/mt ore. Subsequent column leaching tests have further demonstrated the viability of applying this technology to recover gold from carbonaceous ores without first pretreating the material. Gold extractions in the column tests ranged from 69 to 78 pct with thiosulfate consumption ranging from 0.4 to 5.4 kg/mt ore. These results compare to <5 pct gold extraction using standard cyanide leaching conditions.

Jan 1, 1996

By Todor P. Stefanov

The thermal draught within ventilation networks of underground mines depends to a great extent on the shafts depths and degree of change of ventilating air density. When the topology and space orientation of a ventilation network are constant, the dynamics of thermal draught is determined mainly by the variations of the heat- and mass-transfer processes in the openings. This conclusion follows from the well known basic theoretical notions about the thermal draught-aerostatics and thermodynamics [1]. Quantitative evaluation about the influence of heat- and mass-transfer processes on dynamics of thermal draught could be made through: direct mine measurements, special experiments and with the aid of mathematical models. The first two methods produce sufficiently accurative results, however it is very difficult to perform such studies, particularly when these processes are evaluated within a large scope and multifactor aspects. Mathematical models of thermal draught allow to overcome easily these difficulties. The degree of accuracy of results, obtained by this method, depends to a great extent on the degree of approximation achieved by the model to the real heat- and mass-transfer processes. In this paper, with the aid of Bulgarian developed method, algorithm and computer program V WT-4 - for complex evaluation of ventilation parameters in active mine ventilation networks [2], the authors investigate some changes in the thermal draught. Basically, the method is an iterating evaluation of an open set of equations, which represents relationships between the following basic parameters of a mine ventilation network: [ ]

Jan 1, 1980

By S. K. Mishra

Introduction The history of the Australian coal industry is almost as old as the history of Australia after new settlement. The first cargo of coal was exported from Newcastle to India in 1799. Coal has been mined in Australia for almost two centuries. But there are indications that the first coal was processed in 1877 in the Newcastle area. This is nearly 50 years after the first coal processing in Europe. Processing on any significant scale began in 1944 at the Newcastle Steel Works. In Queensland, however, coal processing did not begin until the second quarter of this century. The dramatic growth of mining and processing of Australian coal since the mid-60s is primarily due to the expansion of the export market in Japan, Asia, and Europe. Australian coals Black coal occurs in most of the major sedimentary basins of Australia. The better known deposits of commercial importance are in the Sydney, Bowen, Oakland, and Gailiee Basins. Apart from the Collie Basin in western Australia, other coal deposits of the Arckinga Basin in South Australia, the Bonaparte Basin in Northern Territory, and the Tasmania Basin are basically unexploited. The Sydney Basin of New South Wales and Bowen Basin of Queensland remain the major producers of black coal in Australia. Currently exploited or potentially commercial deposits of black coal in Australia occur in strata ranging in age from Permian to Tertiary. Estimated black coal reserves are summarized in Table 1. Coals from different ages have significant differences in their petrographic characteristics. Many of the Permian coals are usually rich in inertinite. Jurassic and Tertiary coals are typically rich in vitrinite content. Typical petrographic and chemical characteristics of some important Australian coking coals are summarized in Tables 2 and 3. The reserves of coking coals are restricted in the main to the Permian coals of the Sydney and Bowen Basins. Coal deposits in the latter are at shallow depth. A high percentage of these are being strip-mined. On the other hand, in the Sydney Basin, the majority of the reserves of good quality coking coals are at significant depth. The mining cost of these deposits is substantially higher than those in the Bowen Basin. It is usually possible to make strong coke with Australian Permian coals of vitrinite content much lower than the other international coals. But there are many major Permian deposits in Australia where low vitrinite content presents problems. As they are classified as marginal coking coals, optimization of their pro¬cessing plays an important role in meeting the market specifications of coking coal. The major reason for processing Australian coal is to reduce the ash content. Compared with British and some American coals, Australian coals are of relatively high ash content. Unlike American coals, more than 99% of the Australian coal deposits have sulfur content less than 1%. Consequently, sulfur control has never been a major problem. The coking quality of coal is improved simply through the ash reduction in the marketable product. However, with the increase in intensive mechanization and multi-stage handling of coal be-

Jan 9, 1985

By R. Allan Wallis

In the past mining engineers have tended to rely heavily on the advice of fan manufacturers in relation to fan equipment issues. A more adequate approach was advocated in a paper [ Wallis, 1965 ] submitted to the Eighth Commonwealth Mining and Metallurgical Congress held at Surfers Paradise, Australia during 1965. At that time Mount Isa Mine were in the process of installing 3 large 6096mm (20ft) diameter vertical axial flow surface fans of an advanced type [ Mathews et al, 1967 ]. The preliminary feasibility studies prior to preparing the detailed job specification for this project were extremely thorough with the result that it was possible to include detailed information and instructions in the document, ensuring the procurement of equipment that was satisfactory in all respects. Full advantage was taken of expert services provided by external organizations during the large coordinated multi-disciplinary exercise. My continuing activity and development in relation to the technology of axial flow fans is now at a stage where all known design and performance data are accessible through CAD programs [ Wallis and Kipp, 1987 ]. The extensive calculations that were necessary in 1983 can now be carried out in a mere fraction of the time, and with complete confidence. Model testing in order to validate the fan and duct design proposals is, in my view, no longer essential. The first of the computer programs enables a mine ventilation engineer to study a large number of alternative axial fan arrangements for comparison with the centrifugal alternative. By entering the volume flow rate, fan pressure and air density, he can then with ease, and rapidly, investigate the effect of various blading arrangements, downstream evasee area ratios, and hub ratios, on fan diameter and speed, with their related attainable fan efficiencies. This procedure had its origin back in the 60s when I was advising mining companies on new fan equipment. At that time such an investigation was quite lengthy and lacked the precision and completeness that is now available within the present programs. To obtain the major benefit from these outputs, it is most important not to be disconcerted by the three very important nondimensional parameters, namely, the tip flow coefficient (LAMt), the fan pressure coefficient (Kt or Kit), and the swirl coefficient (Es and/or Ep) as these are important when assessing the various design proposals. When seeking an understanding of the role and importance of each of these variables, ample help is provided in the user manual; the design recommendations are summarized in the help screens which are readily accessible within the design programs.

Jan 1, 1989

By Robin J. Hickson

The Grasberg copper-gold deposit was discovered in the spring of 1988, one year before the planned closure of Freeport Indonesia&apos;s original Ertsberg openpit copper mine. In spite of Grasberg&apos;s remote location, 600 m (1968 ft) above the Ertsberg, atop a hitherto inaccessible mountain, Freeport-McMoRan brought its latest open-pit mine into production in the last week of 1989, less than two years after discovery. Freeport Indonesia&apos;s (FI) copper-gold mining operations are located in Irian Jaya, the easternmost province of Indonesia on the western side of the island of New Guinea. Fl&apos;s six ore deposits are all located within a 10- x 10-km&apos; (3.9- x 3.9-sq mile) Contract of Work area. They are all between the elevations of 2900 and 4300 m (9515 and 14,100 ft) above sea level, some 96 km (60 miles) from the island&apos;s southern coast. A 118-km (74-mile) access route connects FT&apos;s port site of Amamapare on the Arafura Sea to the project area. The first section is an 18-km (11-mile) barge waterway. The final 100-km (63mile) is a two-lane gravel highway. The highway terminates 9 km (5.5 miles) beyond the FI townsite at the project&apos;s central mill, some 2850 m (9250 ft) above sea level. The mining areas are separated from the mill by a 780-m (2560-ft) sheer cliff face. The world&apos;s longest free span tramway system, with a total length of more than 1.6 km (1 mile), is the only means of access for men and materials between the mill and the surface mines. Weight restrictions for the tramway for equipment considered for the project are 15.4 t (17 st). The minimum clear width dimension of two tunnels along the portsite access road is 5.6 m (18.4 ft).

Jan 1, 1991

By R. L. Grayson, S. Yuan

A goal-programming-based, worker-scheduling model has been incorporated in the Mine Management Support System (MMSS) for assigning workers to prioritized jobs on a shift basis. In the model, the accomplishment of each regular and non-regular job is a goal, and the objective is minimization of the deviations from the goals. A number of coefficients are employed as premultipliers of the decision variables to address practical considerations associated with the utilization of workers and the requirements of jobs. This model is applied to a 41-worker problem.

Jan 1, 1992

By S. Gallagher, A. Mayton, R. Merkel

The prolonged exposure of equipment operators to shock and whole-body vibration (WBV) is linked to cumulative back, neck and abdominal disorders. In low coal mines, space restrictions make it difficult for seat suspensions to isolate operators from shock and WBV. Researchers at NIOSH&apos;s Pittsburgh Research Laboratory are responding to these issues by investigating viscoelastic foams. For the full-load case, an ergonomic seat made with viscoelastic foams can isolate the shuttle-car operator from shock at 15 Hz. Researchers used results from additional foam testing using an analytical model to identify viscoelastic foams that provide shock isolation at a frequency below 5 Hz.

Jan 1, 2000

By T. Zoltai

Asbestos is a generic term for industrially useful fibers recovered from exploitable deposits of the asbestiform varieties of five silicate minerals: chrysotile, anthophyl-lite, actinolite-tremolite, cummingtorute-grunerite, and rie-beekite. Asbestos and asbestiform fibers of some other minerals are known to be carcinogenic. Minerals crystallized in the asbestiform habit-are characterized by unique properties (morphology, strength and flexibility, physical and chemical durability, and defect-free surface structures). The key to the unusual properties, and health effects, of asbestiform fibers appears to be in their unusual surface structure. In contrast, non-asbestiform crystals of the same minerals, including the five so called asbestos minerals, do not have these properties and are not carcinogenic.

Jan 1, 1989

By P. Somasundaran, D. R. Nagaraj, Jing Wang

Polysaccharides have been widely used as depressants in mineral processing for decades. They constituent one of the most abundant family of biopolymers. However, only a small number of them have been used by industry so far because of a general lack of understanding of interactions between these polymers and minerals. In this work, adsorption tests, electrophoretic mobility measurements, microflotation and fluorescence spectroscopic tests were performed along with computer simulation to explore the mechanistic aspects of guar gum adsorption and conformation on talc as a function of relevant variables such as ionic strength, pH, solvent composition and polymer molecular weight. From microflotation tests, it was found that talc hydrophobicity decreased markedly due to the adsorption of guar gum even at very low concentrations and reached a plateau below moximum adsorption. Guar gum adsorption on talc was found to be not affected significantly by changes in solution conditions such as pH and ionic strength, ruling out electrostatic force as controlling factor for adsorption. Fluorescence spectroscopic studies showed no evidence of the formation of hydrophobic domains at talc-aqueous interface. Also urea, a hydrogen bond breaker, reduced the adsorption of guar on talc. All of the above results suggest that one of the main driving forces for guar adsorption on talc is hydrogen bonding in preference to electrostatic or hydrophobic force. This information should help toward designing reagents of optimum molecular architecture for efficient depression, dispersion or other such surface modification of particles.

Jan 1, 2005

By Jerry R. Johanson

Introduction Many solids processes that look feasible on paper or even in pilot studies become disasters in full scale. Changes in solids flow characteristics from pilot scale to full scale be- cause of larger solids contact pressures, thermal shocks, or unforeseen temperature excursions often cause full-scale solids flow problems not encountered in the laboratory or pilot studies. Fortunately, proper applications of solids flow principals and solids flow properties measurement at full scale conditions can anticipate the problems and thus provide an accurate basis for full-scale design or existing plant modifications. Solids flow properties The basic solids flow property definitions are given in Table 1 (Johanson, 1966, 1976, 1978, 1985). In this section, the author will discuss each property and its potential for creating full-scale pilot plants. Unconfined yield strength The unconfined yield strength of a bulk solid determines the tendency for cohesive hangups of the solids in the process and is effected by the time at rest, chemical reactions, temperature, liquid content, solids size consist, and phase changes of solids or fluids involved in the process. One of the common mistakes is to consider the solids condition only at the beginning and the end of the process. For example, consider the direct reduction of iron ore. The feed solids are free-flowing, hard lump ore or pellets. The end result is a hard, free-flowing reduced sponge iron lump or pellet. One might conclude that the process involves free-flowing lumps. This conclusion may seem reasonable based on laboratory studies oreven pilot plant studies where solids contact pressures are very low. Unfortunately, during the reduction reactions at high temperatures, the rock or pellets soften and, with solids contact pressures associated with the full-scale plant, may fuse together, thus providing a possible solids hangup in the moving bed reactor not evident in the low pressure pilot scale. Fig. 1 shows some typical unconfined yield strength measurements for pellets as a function of solids contact pressure at various times at rest. Note at low consolidation pressures, generally associated with laboratory or pilot plant studies, the pellets show no strength unless held at rest for an extended time. This will produce a very free-flowing condition in pilot plants that will not exist in the full size reactor.

Jan 1, 1990

By T. W. Healy, M. S. Moignard

The use of electrokinetic or zeta-potential phenomena in studies of the properties of mineral sulphides has increased greatly over recent years. This review aims to examine and discuss the body of literature on the subject of electrokinetic properties of sulphides in a comprehensive and critical manner. Although the review covers the period from 1925 to 1975, it is only in the past ten years that researchers have been fully aware of the implications and problems of chemical reactions, notably oxidation and precipitation reactions, on the surface properties of sulphide minerals. These papers are discussed in more detail than the earlier publications. A table containing a list of determinations of iso-electric- points and points-of-zero-charge of mineral sulphides, and the methods employed in obtaining these results, is presented.

Jan 1, 1976