Search Documents

By J. P. Vandenhoeck

Sizing devices used commercially are unfortunately not 100% efficient, the splits that can be obtained are usually inferior to the results obtained in the laboratory. Often the capital and operating costs of equipment capable of high sizing efficiency cannot be justified by the economics or requirements of the process. To reconcile the desired sizing efficiency needed to obtain optimum process requirements with the sizing efficiency of equipment economically practical, it is often necessary or desirable to predict the gradation and weight splits of the products obtained based on the expectant efficiency of the contemplated sizing device or method. The less efficient the sizing device one must employ, the more important it is to know the results that may be expected for the establishment of the optimum flow sheet and the more difficult it becomes to estimate the results accurately. Air classification equipment which sizes materials by opposing the drag force created by an air stream acting on a particle with a combination of gravitational, inertial or centrifugal forces are substantially less efficient than, for example, a laboratory sieve analysis. Air classifiers allow oversize material to contaminate the fine fraction and leave undersize material in the coarse fraction. The techniques employed to predict the gradation and weight splits obtained from air classification outlined below are adaptable to other sizing devices less than 100% efficient such as screens, sifters and wet classifiers.

Jan 1, 1965

By Fred T. Towne

There are a number of air classifiers manufactured throughout the United States and the rest of the world. The classifiers manufactured by Alpine, A. G. of Augsburg, Germany, are unique in their abilities. It is this uniqueness that I wish to delve into and in this respect we will limit this discussion primarily to the classifiers as manufactured by Alpine. It has been reported in the past that these classifiers were introduced into the. United States in the late 50's. Until the introduction of the Alpine Classifiers, air classification seldom produced a satisfactory fractionation of a product below 45 microns (325 mesh) or above approximately 22 mesh. It has been a common practice to classify fine materials which used water as a carrier medium The use of centrifuges are today producing thousands of tons of finely partitive powders in the very small particle size range. The use of centrifuges in connection with wet grinding mills has increased the rates of production of these mills considerably.

Jan 1, 1965

By Francisco J. Escandon V.

Numerous lead-zinc-barite-fluorite ore deposits, with simple mineralogy and roughly concordant with bedding, are found widely distributed all over the world, having been denominated and well described as "stratiform deposits" or "strata-bound ore bodies", not having any genetic relationship. During several years, its origin has been discussed, without getting to general agreement regarding the main mining districts of this type. Through studies made of large stratiform deposits in the United States, Europe and Russia, it has been found that there are, within this classification, syngenctic diagenetic and epigenetic ore bodies. During the Symposium about the genesis of the stratiform lead-zinc-fluorite-barite deposits, carried out in New York in 1966, Frank G. Snyder (1), presented an excellent analysis of the theories of the origin of these deposits and of the evaluation of the criteria regarding classification. As per his definitions (Table 1), "a deposit is syngenetic if formed by processes similar to and simultaneously with the enclosing rock, epigenetic if introduced into a pre-existing rock and a diagenetic origin implies deposition of metals with the host sediments but with recrystallization, rearrengement and limited migration".

Jan 1, 1974

By R. E. Blair

The economics of the producer-consumer interface - the route from mine to market - impact much more severely on specialty industrial minerals, extender/fillers that have to be sold, than on commodity industrial minerals that are basically supplied. Working capital costs for inventories and accounts receivable, fixed capital costs for storage/ warehousing/distribution, and sales and marketing costs all make the extender/filler producer much more of a marketer than a miner. The future survival of an extender/filler producer will primarily depend on the skill he has in the economics of the interface.

Jan 1, 1981

By H. O. Seigel

This is an introductory paper on a new method of prospecting for mineral deposits which has been developed by Scintrex Limited. The method, which we call Luminex, for luminescent mineral exploration, is based on time- resolved mineral luminescence created by an ultraviolet light source. It has the ability to detect and resolve a group of key minerals which are either ore minerals themselves, or more often, are accessory or pathfinder minerals for certain types of economic ore deposits. Fortunately, these minerals are commonly found at the earth's surface, even in areas of considerable weathering. The method extends the range of mineral deposits which are remotely detectable from the air to include those such as tungsten, tin, molybdenum, gold and bedded lead-zinc deposits and, is therefore, a natural supplement to our three classical methods of airborne geophysics.

Jan 1, 1983

By J. P. Van Dillen

Continuing interest in processes that will effect separations in the fine particle size range has prompted intense interest in the use of high gradient magnetic separation (HGMS) for beneficiation of uranium ores. Some of the uranium minerals are paramagnetic and hence are amenable to concentration by HGMS. This paper presents a brief review of the problems associated with uranium ores beneficiation, a description of the HGNS process, and the effects of the parameters--pulp velocity, field strength, matrix loading and magnetic field gradient on product recovery and grade. Unsatisfactory separation of uranium minerals by HGHS is related to ore specific properties such as lack of liberation, fine dissemination of uranium minerals, uniform distribution of magnetic minerals throughout the ore matrix and interference of micron sized slimes. Experimental techniques to identify and resolve some of these problems are outlined.

Jan 1, 1982

By W. J. Turbeville

The subject of this discussion is timely. The U.S. phosphate industry is suffering the throes of depression. It's plight is a matter of widespread concern. The future role of the U.S. industry in world markets is of particular interest. If we should prognosticate phosphate supply-demand on the basis of recent history, we would face a puzzling choice of scenario. In 1980, perhaps the best year ever for U.S. phosphate, 54.6 million metric tons of phosphate rock entered the market place. Of this, more than half was exported -- divided almost equally - as rock or phosphate fertilizer. During the last half of 1981 the situation had begun to change.

Jan 1, 1983

By Neal P. Cochran

My talk today is an effort to project our thinking forward a few years to that point in the future when we will be producing gas and liquid fuels from coal. To those of you that are concerned with meeting today's production quota--my remarks may sound like a Buck Rogers projection. Not so. Although I'm talking about the future, please understand that my thoughts are focused on the near term future. The coal plant of the future will be an energy plant producing energy products to meet the needs of our modern society. This plant is an outgrowth of Government- industry cooperation. Much of the research work that makes such a plant possible was jointly funded, other work was a continuation into development of private research expenditures, other work was performed by private research organizations with Government funding, other work was performed in Government laboratories, both State and Federal. As indicated above, and in the title of my talk, I expect to describe the coal plant of the future. I will describe a plant producing Carbon, Oil, Pipeline gas, and Electricity--Project COPE. This plant copes with the Atomic-Nuclear Group. As stated above, this plant is an energy plant. Energy plants today are large-scale operations. Power plants of 5,000 megawatts are projected, refineries of 500,000 daily barrels are near term probabilities, 48" transcontinental gas pipelines are with us today and 25,000 daily ton mines are here as well. The COPE plant will be of the same general size and require 50,000 - 100,000 tons of coal per day.

Jan 1, 1969

By Alan J. Michaels

The paper addresses the problem of the high costs of accidents ad how AMAX Inc. - a diversified natural resources company - has managed to control its losses through a tri-thrusted approach of: (1) management commitment, (2) methods of implementation that are tailored to each division or local unit, and (3) a reward system for outstanding performance. Specific attention is focused on the Corporate Loss Prevention Department's "10 Point Program for Loss Prevention Management".

Jan 1, 1981

By C. H. Cox

The Alumet Company of Golden, Colorado, is currently engaged in the development of their Diamond Creek and Lanes Creek phosphate ore bodies located near Soda Springs, Idaho. The Alumet Company is a partnership of National Steel, Southwire Co., and Earth Science Inc. Davy Powergas, Inc., of Florida was contracted by Alumet to perform an evaluation study of these properties and, in general, determine the tonnage of altered and unaltered phosphate reserves which would be amenable to beneficiation and production of merchantable phosphate rock (defined as material with a P2O5 content of 3 1.0% and greater). The Colorado School of Mines Research Institute was retained by Davy Powergas to develop a beneficiation method for the studies of the altered and unaltered ores. Ore reserves were classified by Davy in a comprehensive range of categories such that any partial grouping could be made as dictated by future mine planning, mine or mill design, or prevalent economic conditions. Categories included ore horizon, stripping ratio, degree of certainty of their existence, and physical and chemical characteristics. The last category was of interest for beneficiation considerations in that it dealt with the degree of alteration of the phosphate ore.

Jan 1, 1979

By Trevor R. Ellis

In this paper a method is presented for estimating the specifications of sandstone-type uranium deposits which will be the minimum that can meet a company's economic requirements for investment. The method interpolates and extrapolates from available cost data for typical mines to provide the costs for a wide range of possible deposits. The range of deposits achieving the company's required discounted cash flow rate of return on investment at an estimated uranium oxide selling price is then calculated, thus giving the complete range of deposits which meet the minimum required specifications. Prospects are then evaluated by comparison with these minimum requirements.

Jan 1, 1979

By R. A. Matuszak

U.S. Government sponsored studies proclaim large reductions in surface mine productivity. Consulting studies place a large share of the blame on increased governmental regulatory activities and on inexperienced, improperly train people. Union rules, which allow indescriminate bidding for job openings, seem to be a major factor causing the lack of experience in spite of elaborate training programs.

Jan 1, 1982

By K. C. Watts

The Silver City mining region is located in Grant County, southwestern New Mexico (Fig. 1). This area is well known, having produced large tonnages of base and lesser amounts of precious metals over the past several years. Mining within the region continues today, as well as exploration activity, which seems to have been on the increase since the recent discovery of a large skarn-associated Zn-Pb-Cu replacement deposit near Pinos Altos, a mineral district within the region (McKnight and Fellows, 1978). Because the Silver City area contains a number of mineral districts and retains promise for additional deposits, as suggested by widespread hydrothermal alteration and favorable igneous rocks, it was selected as the focus of two independent geochemical studies, both seeking to enhance anomaly-to- background contrast in order to improve our abilities to detect blind metal deposits or subtle manifestations of near-surface occurrences. The first of these independent studies involved the systematic sampling of those secondary Fe-Mn oxides that occur within coatings, selvages, and fault fillings, and then the selective extraction of these oxides from the host-rock matrix by chemical methods. The second study sought to isolate clastic Fe-Mn-rich materials from the heavy fraction of stream alluvium. The ultimate source of the clastic Fe-Mn oxides is presumed to be the same coatings, selvages, and fault fillings sought by the direct sampling of joints, but has been transported as a result of lateral erosional processes.

Jan 1, 1981

By T. J. Joiner

A critical demand exists to develop new mineral resources, and the need for exploration techniques to supplement costly test drilling is becoming; more acute. In the past few years more industries have begun experimenting with geophysical methods to locate and define mineral deposits and delineate reserves. The new techniques have proven profitable in many instances. As a part of a broad long range program to study the mineral resources of Alabama, and in response to requests from land owners and mining companies, the Geological Survey of Alabama is investi¬gating the occurrence of bauxite and kaolin deposits in the Eufeula area. This project is supported by special funds appropriated for this purpose by the Alabama Legislature.

Jan 1, 1966

By A. L. Crandell

The Cortez Mining District has had a long history of mining activity dating back to 1862 as previously reported (1) (2). More recently Cortez Gold Mines (i) has operated a cyanide leach, counter current decantation (CCD) recovery gold mill from January 1969 to February 1976. This type of plant has been standard in the U.S. for treating higher grade finely disseminated gold in Carlin type ores. The mill was initially operated from 1969 to 1973 at 1520 tonnes per day on oxidized ore from the Cortez ore body. Starting in 1973, the mill was operated at 2050 tonnes per day on softer, less oxidized, high clay ore from Gold Acres which is located 13 kilometers to the west of the Cortez installation. In February of 1976 the oxidized portion of the ore body at Gold Acres was depleted and the mill ceased operation. Successful heap leaching of the lower grade portion of the ores was practiced at both Cortez and Gold Acres to supplement the milling operations. Much valuable experience was gained in the operation of these two heap leaching programs and is well described in an earlier publication (3). Releaching of the ore heaps at Gold Acres and Cortez was continued with a limited crew from 1976 to 1979.

Jan 1, 1986

By T. Cantwell

Techniques useful in operations, analysis are applied to the problem of planning an exploration program. The model used treats mineral exploration as a Markov process, and maximization of gain is the criteria determining the optimum program. The mathematical description of the model and the optimization are first worked out. Application of the mathematics to several simple examples is given. Finally, comparison of the data necessary to use this operations analysis with the available data shows that the method can only be a guide to planning an exploration program.

Jan 1, 1962

By M. Misra

The dispersion of oily collector has significant effect on the flotation recovery of ultrafine coal. Generally, reagent dispersion is accomplished by mechanical mixing and/or ultrasonic agitation, followed by direct addition of dispersed collector into the flotation cell. However, such dispersion and reagent addition techniques are invariably inadequate and non-selective. A new collector utilization technique involving gas phase transport of atomized collector has shown improved results when compared to conventional reagent addition techniques. This new technique involves atomization of the collector into the gas stream. Under these circumstances an aerosol is introduced into the flotation cell. Initially, the oil is dispersed within the gas phase (continuous with respect to oil) and the gas phase is dispersed within the pulp (continuous with respect to aerosol). In the flotation cell, the atomized oil droplets coalesce on the bubble's surface and create a de-facto oil-encapsulated bubble. This approach provides excellent dispersion, increases selectivity, and most significantly increases the flotation rate of ultrafine coal. Furthermore, atomization of collector/frother combinations yielded improved flotation yields and maintained near uniform froth levels which is a desirable feature in coal flotation. In addition to flotation experiments, microscopic examinations of the attachment of oil-coated bubbles at a coal surface were conducted by attachment-time and contact-angle measurements. The oil coated bubbles attach at significantly faster rates and with a higher contact angle than do oil free bubbles.

Jan 1, 1987

Canada is a major producer of chrysotile asbestos. In fact, Canada accounts for approximately one third of the world chrysotile asbestos production. Deposits are mined and the fiber processed in Québec, in British Columbia on the West Coast and in Newfoundland in the Atlantic region. Foremost among the Canadian provinces is obviously Québec. Some 85% of Canadian deliveries come from mines located in the Eastern Townships, a region which lies along the southshore of the St. Lawrence River, between Montreal and Québec City. At the heart of this vast territory, five (5) mining towns make up what is called the Québec asbestos region. Total capacity of the five (5) mining producers of Québec is about 1 366 000 tonnes.

Jan 1, 1981

By C. B. Daellenbach

The influence of reduction roasting and thermal shock on the grindability of a refractory low-grade Michigan iron ore was examined in bench scale tests. The quantitative effects of the various treatments were evaluated at three sieve levels: 48, 100, and 400 mesh, using ball mill grindability and work index parameters as response indicators. Data from the testing program were analyzed statistically as a means of isolating the effects of cooling rate, roasting temperature, and ore chemical condition. All three variables were found to have an important influence on the grindability of the treated ore; ore chemical condition and roasting temperature had the most pronounced effects.

Jan 1, 1970

By R. J. Morlock

Prior to 1912, coal research for Republic Steel, Corporation was limited to a periodic box test conducted in a commercial coke oven. Then in 1912, a Koppers movable-wall test oven was -built to research wall pressures for selected blends and to conduct other varied research work. In the 1950's economic pressures caused a reassessment of position resulting in the establishment of a Coal and Coal Chemical research group in 1956. In 1958 this group, along with other groups of research endeavor were incorporated into the new Republic Steel Corporation Research Center at Independence¬ Ohio. Currently this section is divided into four groups. 1) Coal Preparation, 2) Coal-Chemicals, 3) Coal Characterization, and 4) Coal Carbonization. The objective of each group is described, and a brief listing of the work done under the first three groups is indicated. A more detailed description of the studies by the Coal Carbonization group of the coking characteristics of Republic Steel Corporation's coals as blended among themselves or in conjunction with selected purchased coals follows. The wall pressure, contraction, and stability index criteria are specified, and the method of assessing these criteria as a function of blend composition is indicated.

Jan 1, 1963