Search Documents

By Stanislaw Wasilewski, Zdzislaw Krzystanek

The CMC-3 new generation system for continuous methane monitoring enables on-line measurement of methane concentration within the range of 0-100% CH4 with a great autonomy of operation. In principle the system has been worked out in the asspect of hazard detection in mines endangered with rock and gas outbursts. But after last crash in the Halemba colliery, according to the recommendation of the after-accident committee, the system was directed to this colliery for operational tests. The paper describes construction and functions of this system and gives some results of tests conducted at the Halemba colliery. The results point out the necessity of using monitoring equipment of continuous operation in mines of high dynamics of methane emission. INTRODUCTION Commonly used in Polish coal mining the methane monitoring systems of CTT/63/46 Up or CMM-20 and CMC-1 type are based on cyclic measurements with 4-minute repetition of measurements. This period has been stated sufficient from viewpoint of methane emission dynamics under normal exploatation. In these systems, automatic switching-off electrical power is performed by the surface station, i.e in case of detecting exceeded concentration value the station generates control pulse signal which actuates the switchng-off devices CRA and IZZO. Such a way of disconnection causes a considerable time delay, up to several minutes, in electric power break at hazardous areas. In the methane monitoring system with the new CMC-3 station, the different phylosophy of operation has been applied. Measurement of methane concentration is performed in a continnous way. In case of exceeding the alarm value, immediate control of the IZZO unit directly by methane monitor follows and consequently energy break without necessity of communicating with the surface station. Alarm values are set directly in methane monitor. The system ensures central powering of underground equipment from the surface, and in case of power failure the methane monitor equipped with battery operates autonomously for about 12 hours. Such an extention of the methane monitor funtionality has been achieved thanks to the use of internal microprocessor controller. The system with the CMC-3 station has been worked out in the aspect of methane hazard detection in mines exposed to gas outbursts. But after last gas explosion, according the desicion of the After-accident Commitee, the system was installed in the Halemba coliery where it underwent operational tests. Besides

Jan 1, 1993

By Sam H. Patterson

Fuller's earth and bentonite are two clay commodities that are interrelated either by mineral composition or use. Because of this interrelation and the sale of both for many different uses, some ambiguity in their classification has resulted. The term "fuller's earth" has no compositional or mineralogical meaning, and it is used more or less as a catchall for any clay or earthy material suitable for certain uses. Most, but not all, of these uses require absorbent properties. Bentonite by geologic definition must have formed from volcanic ash or tuff or the glassy material in volcanic rock; most bentonites consist chiefly of montmorillonite but other clay minerals may be present. In industrial usage the term "bentonite" is applied to any clay consisting chiefly of montmorillonite, irrespective of origin. Georgia and Florida have historically been the leading States in the production of fuller's earth; bentonite has been produced in Alabama on a small scale. The first major use of fuller's earth was in refining of oils. Other materials have replaced fuller's earth for this purpose to a major extent, but many new uses for fuller's earth have been found, and production has increased in recent years. The new uses include absorbent products, insecticide and pesticide carriers, drilling mud, and many others. The bentonite now produced in Alabama is of the "southern," "low selling," or "calcium" type and is used mainly as foundry-sand bond. Most of the fuller's earth mined now is in the Hawthorn Formation of Miocene age; a lesser amount is produced from the Twiggs Clay Member and other beds in the Barnwell Formation of Eocene age. Inactive pits from which fuller's-earth was produced from other formations occur at several localities. The bentonite now mined in Alabama is in beds of Cretaceous age; several years ago bentonite was produced from Eocene beds in this State.

Jan 1, 1972

By J. L. Workman

The stability of spoil and highwall slopes are important to successful strip mining. This paper discusses soil parameters of importance in stability analysis. The common mechanisms of spoil failure are discussed. Modes of highwall failure are also outlined. The importance of water to stability is presented. Dragline mining methods most suited to creating spoil and highwall profiles that address stability needs are provided. It is concluded that groundwater and surface runoff must be well controlled, and that it will often be necessary to modify spoil and highwall configurations to achieve a stable overall slope angle.

Jan 1, 1996

By Patrick Shea

Old mine workings are found throughout the Western United Sates on lands administered by the U.S. Bureau of Land Management, U.S. Forest Service and private lands. Some of these mine workings date back to the late 1800s. There may be as many as 100,000 sites on lands administered by the National Park Service, U.S. Forest Service and Bureau of Land Management. The U.S. Department of the Interior has worked with the U.S. Geological Survey, the U.S. Forest Service, the U.S. Environmental Protection Agency, and western state governments to identify and prioritize these sites on Bureau of Land Management, National Park Service and U.S. Forest Service administered lands. This presentation will discuss the accomplishments we have made to date to clean up inactive and abandoned mine sites, focusing primarily on lands administered by the Bureau of Land Management.

Jan 1, 2000

By H. Jung, J. Kim, Y. Lee, Y. Seo

"Shale gas has become an increasingly important source of natural gas supply in North America and around the world. Horizontal drilling and multi-stage hydraulic fracturing are the two key enabling technologies for the economic development of these shale gas reservoirs. It is believed that gas in shale reservoirs is mainly composed of free gas within fractures and pores and adsorbed gas in organic matter (kerogen). It is generally assumed in the literature that the monolayer Langmuir isotherm describes gas adsorption behavior in shale gas reservoirs. In this work, we have analyzed several experimental measurements of methane adsorption from the Horn River Shale core samples that obey the Langmuir isotherm. INTRODUCTION In nature, gas shales are characterized by extremely small grain size, extremely low permeability on the order of nano-Darcy (10-6 md), small porosity, and high total organic carbon (TOC). Shale can serve as both source and reservoir rock. The amount of gas in place in shale is strongly affected by the TOC, clays, and the adsorption ability of methane on the internal surface of solid (Martin et al., 2010). Since a considerable amount of gas in shale reservoirs is adsorbed, investigation of gas adsorption can provide critical insights into evaluation of well performance and reservoir characterization. Generally, natural gas in shale reservoirs is stored as free gas in both larger mineral pores and natural fractures, as well as adsorbed gas within organic matter (Leahy-Dios et al., 2011). EXPERIMENT METHOD & THEORY Adsorption Experiment Several experiments were carried out on 9 shale core samples obtained in a vertical well drilled within Horn River basin (Figure 1). The CH4 adsorption isotherms were measured for the different depth. In order to measure the amount of adsorbed gas, the high pressure Belsorp-HP equipment applying volumetric method was used. The temperature was kept at 298 K and pressure was increased up to 18 MPa. Approximately 5 g of crushed sample was used for each measurement."

Jan 1, 2016

By C. Dale Elifrits

Observations made from laboratory analysis of samples of fine-grained argillaceous materials (shales) subjected to various changes in moisture content have been correlated to loss of strength in the rock material. This reaction to a change in in-situ conditions (subsequent to mining) at a mine site combined with the observed relationships of surface-disturbing subsidence features at locations where the predominant overburden material is fine-grained, provides a predictive tool for the subsidence engineer.

Jan 1, 1983

By David A. Zegeer

It's a pleasure to be here, and an honor to be invited to address this distinguished group of professionals. Today, I'd like to begin with an overview of progress in coal mine safety and health. I'll discuss some current areas of concern. And I'll make some suggestions as to where we may be headed in the future. This year marks the coal industry's 15th anniversary under the Coal Mine Safety and Health Act, which took effect in 1970. We have come a long way in those 15 years. As a coal mining man from way back, I remember the era when the Coal Mine Safety and Health Act first was passed. Some of you may remember it, too. At that time, the safety and health of coal miners was in the public eye even more than it is at present. One reason was a mine explosion that killed 78 miners when it occurred in a large underground coal mine in November 1968. That disaster raised tremendous public concern about protecting the safety of miners.

Jan 1, 1985

By Perry N. Halstead

The primary objective of the structural geology portion of the Kennecott Copper Corporation-U. S. Bureau of Mines Pit Slope Stability Study was to determine the attitude, geometry, and spatial distribution of geologic structures of the west wall of the Kimbley Pit for use in designing a maximum stable slope for the pit. A corollary objective was to develop and refine techniques for collecting and analyzing geologic structural data with emphasis on numerical methods that could be integrated with other aspects of pit design. Surface mapping techniques used were a modification of conventional joint set mapping and a detailed linear sampling method. For subsurface investigations both oriented core and a borehole camera were used. It was determined that the major faults in the area were favorably oriented for mining a steep stable slope. The jointing or natural fracturing, although complex, was not random in attitude and consisted of several persistent fracture sets and a number of secondary sets. The attitude of the persistent fracture sets was favorable for steeper slope angles, and these attitudes were used in the design considerations. There was no significant difference between the attitude of the fracture sets determined from the former and new slope face.

Jan 1, 1968

By Joseph O. Cook

I know this is, at best, a frustrating period for the coal mining industry. About 20,000 miners have been laid off, mostly in the Appalachian and mid-western areas, and several mines are working less than 5 days a week; however, the industry is experiencing modern growth and, at least, there is the potential for future growth. The coal industry is probably only operating at about 80 percent of its present capacity, and it is certainly capable of helping this country solve its energy problems. Growth, as a rule, does not come easy, and growth in the coal industry is no exception to this rule. Many formidable challenges have to be overcome. As we all know, mining relies very heavily on the earth sciences, which have advanced significantly in the past few years, but we are always working in a changing environment which in most cases is a hostile environment. Large quantities of material are quickly extracted and rapidly moved in, generally speaking, a very confined area. The very nature of the mining business directly and constantly impacts our environment during this period in which the Nation and the world has become increasingly smaller and more concerned about protecting our environment. In addition, growth brings about an expanding work force which is increasingly younger and less experienced.

Jan 1, 1980

By R. H. King

This paper describes the results of an underground coal mine trial installation of a shielded trailing cable. The cable was a three conductor, round, type SHC-GC, and was installed on a shuttle car in a conventional room and pillar mining section. The purpose of presenting the information is to prepare mine operators for proposed legislation that will require shielding on low-voltage trailing cables. Specifically, machine modifications are required to cable reels, packing glands, and couplers. Cable splicing is not as complex as expected but additional materials are needed in the kit and splice training is necessary. Even though shielding will cause some problems for the mine operator, it can reduce the hazard of electrical shock to mine workers. This paper will present information that mine operators can use to solve most of the problems that will be encountered if they are required to install shielded cables. The in-mine evaluation was funded by the U.S. Bureau of Mines.

Jan 1, 1980

By John J. Dran

In recent years, market rates of interest have risen well above their historical long-term average. Also during this period, the short-term variability of interest rates has been greater than in prior years. Interest rates have a significant effect on the operation of our economy. They influence the extractive industries in a number of ways. Their major long- range impact is on investment decisions - specifically the valuation of mineral deposits. An understanding of the factors that influence interest rates is important to the engineer or businessman who makes the investment decisions for the mining company. The effect of changes in the market rate of interest on the value of mineral reserves is critical to the future financial success of the mining enterprise. The most common simplification of the factors determining the level of interest rates is that they are a function of the demand for and the supply of money. While this is an oversimplification, most businessmen would be hard- pressed to provide a better explanation. The purpose of this paper is to explore certain fundamental economic aspects of interest rates and to examine their effect on the analysis of investment in mineral deposits.

Jan 1, 1975

A significant technological development is discussed for the processing of certain problem power plant flyashes which contain a high water soluble mineral content and which are known to yield inferior flyash based brick. This development is based on the addition of hydrochloric acid to the flyash-bottom ash-sodium silicate blends used for the production of flyash based structures. Favorable changes are evident in (1) sodium silicate consumption, where often approximately one-half of the amount used for making brick from normal flyash is required; (2) processing costs; and (3) strength and appearance of the resulting freshly formed green and fired structural products. In some high cost instances-(above the cost of 30 dollars or less per thousand brick estimated for normal flyashes) hydrochloric acid additions can replace or reduce other costly additives required with problem flyashes to result in a savings of as much as nine dollars per thousand brick. These developments offer promising possibilities for utilizing problem flyashes as well as flyashes which may come into contact with water soluble, sulfur as a result of the eventual application of certain experimental air pollution control processes.

Jan 1, 1968

By Jack V. Hill

A unique type of grinding mill liner has been developed by Waagner-Biro A.G. of Austria. This liner system, termed an angular spiral lining (.ESL), was, successfully tested by Magma Copper Company's San Manuel concentrator in both their 10 Ft x 10 Ft (3.05m x 3.05m) and 12 Ft, 6 In x 14 Ft (3.81m x 4.27m) grate discharge wet grinding ball mills. Magma Copper's savings in power and grinding balls justified conversion of more than half of their twenty-six ball mills to the ESL system.1,2 The ASL system was provided by the Capitol Castings Division of Midland Ross Corporation, the exclusive licensee for such conversions. Capitol Castings proposed the following as expected benefits from installation of an ASL system in an 18 Ft x 21 Ft (5.49m x 6.40m) overflow discharge wet grinding ball mill at the Pinto Valley Operation of Cities Service Company: "(a) Reduction of power consumption per ton of ore milled = 12%, (b) Increased throughput = 6%, (c) Reduction of ball consumption = 6%."

Jan 1, 1982

By Ronald W. Marrs

Kimberlite contains a unique assemblage of minerals and exhibits a characteristic pattern of spectral reflectance in the visible and near-infrared wavelength region. This spectral pattern is readily discerned in well-exposed kimberlite outcrops, but becomes increasingly difficult to identify when outcrops are partially covered by vegetation or soils derived from non-kiaberlitic materials. Detection of poorly exposed kimberlite diatremes is possible using multispectral imaging techniques in which spectral bands are chosen to optimize contrast between he kimberlitic soils, non-kimberlitic soils and vegetation. Careful processing of the multi-spectral data is also essential in order to separate the spectral signature of kimberlite from the signatures of other components of the scene.

Jan 1, 1984

By William M. Kester

Finely sized Upper Freeport coals are beneficiated to reduce ash and sulfur using high-intensity magnetic separation to process both (1) raw, untreated coal as well as (2) raw coal which was pre-treated thermally with steam and air. Substantial, sulfur and ash reduction can be obtained using both approaches to magnetic beneficiation of coal fines, but evidence indicates that pre-treatment which would constitute a costly supplementary step is technically inferior to the direct beneficiation of raw, untreated coal. These bench-scale studies demonstrate that if high-intensity,; high capacity, dry, magnetic beneficiation equipment can be developed and' installed at coal burning power plants or at appropriate points in coal preparation plants substantial quantities of sulfur may be removable from coal after pulverization as a means' to reduce air pollution.

Jan 1, 1965

By Edward A. Vitunac

The emerging importance of pneumatic conveying systems for bulk materials is becoming recognized by more persons responsible for materials management as consultants, at the corporate level and at the plant level. They have learned that the economic advantages of a pneumatic system are frequently decisive when compared to alternate methods. Included in these advantages are relative simplicity, ease of installation, flexibility, ease of maintenance, cleanliness, safety and ease of automation to the degree desired. In general, installed costs favor a pneumatic system when compared to competing mechanical systems if the transporting distances are long or to and from many points. In addition, supplemental use such as cooling, heating, or drying may supply the incremental value required to justify its selection. (1). The main disadvantages of a pneumatic system is the greater horsepower required per unit weight of material conveyed and material limits in abrasiveness and density. In addition, there is a tendency to increase material breakage at changes of direction and at any obstruction such as the imperfect butting of one, piece of pipe to another in the conveying line. Classification of the material at the discharge may also cause problems in dusting and segregation. Materials weighing less than 4 pounds per cubic foot tend to cause feeding and collecting problems although they can be conveyed easily. Material between 4 and 20 pounds per cubic foot can be handled with less problems but flow rate is hard to predict. The 20 to 60 pounds per cubic foot range offers best results; whereas, over 60 pounds per cubic foot, materials tend to drop out of the air stream and settle in the pipe line unless careful provisions are made to prevent it. (2).

Jan 1, 1967

By Edwarde R. May

The Flambeau volcanogenic massive sulfide deposit located in northwestern Wisconsin occurs within the southern lobe of the Canadian Precambrian Shield. The steeply dipping tabular body occurs in a complex pile of cyclic schistose intermediate to felsic fragmental volcanics. No chloritic alteration pipe is recognized but adjacent rocks have undergone magnesia metasomatism and subsequently were metamorphosed to the upper greenschist and lower amphibolite facies. Although modest in size the deposit is of special interest in that it has an extensive and well preserved supergene enrichment blanket. Economic minerals found within a pyritized quartz-sericite schist are chalcocite and bornite overlying primary chalcopyrite.

Jan 1, 1976

By D. N. Hillhouse

The economics of exploration target selection can be measured ultimately only against a company's success at developing mines. In the following brief history of the mine acquisitions of one company, Placer Development Limited, I try to identify the principal targeting parameters and the principal skills that came into play for each property and examine how these have changed with time. The process of target selection in exploration is directed: - first by corporate investment criteria which define objectives and acceptable levels of risk for pursuit of those objectives; - second by experience and skills which permit us to minimize risk; and - third by anticipation of future events relating to ore discoveries and changes in external risk factors.

Jan 1, 1984

By P. A. Rittenhouse

Reserves of potash are more than adequate to meet future world demand for this primary fertilizer nutrient. The bulk of both reserves and current production is located in only a few countries. Recent attention has focused on potential development of smaller reserves to supply local markets in developing areas of the world. However, most new capacity in the next decade will be built in countries with large current production and reserves. The paper reviews current and future projects that will add to the world supply of potash.

Jan 1, 1985

By Robert L. Russell

The Bunker Hill Mine, located in the Coeur d'Alene Mining District at Kellogg, Idaho, has been a major producer of lead-silver-zinc ores since its discovery in 1887. The mine has produced over 29 million tons of ore from some 20 to 25 veins and ore zones, and now covers an area approximately one mile in length and one-half mile in width. The active section of the mine extends from 2500 ft above sea level to 1600 ft below sea level. Production is presently at the rate of about 1700 tons of ore per day. A two-mile adit, the Kellogg Tunnel, at the 2500 elevation, provides access to the main shaft area. Ore is hoisted to the adit level through a 5000-ft, 500-inclined shaft, extending to the lowermost haulage level 1200 ft below sea level. Primary shaft service for men and materials is supplied by three major internal, inclined shafts equipped with double-drum hoists. Present production requires ten levels to serve for mainline track haulage. These range up to 5000 ft in length and are either 200 or 400 vertical feet apart. Also, many intermediate levels exist throughout the mine. The conventional and autoloader mechanized square-set and cut-and-fill mining methods used throughout the mine have been the subject of a recent paper(l). One-third of current production is from vein-type ore bodies which are long distances from main shaft areas. Such veins generally dip about 450, have relatively narrow widths of from 3 to 20 ft, and usually contain less than 500,000 tons of ore. For many years, ore bodies thus situated have been developed by means of a separate inclined, timbered service shaft-raise connecting two or more main haulage levels. These commonly range from 400 to 1000 ft in vertical extent and are equipped with 25 to 50 hp electric, single-drum hoists. Intermediate levels are driven as conventional track drifts at 100-ft vertical intervals between the haulage levels. Ore and waste from the intermediate levels are trammed to orepasses for delivery to the lowermost haulage level servicing an ore body. The final result may be visualized as a number of small mines within a large mine. The problems of high development costs and high total development time, and the large amount and high cost of providing materials handl ing and ore haulage service while producing from this isolated type of stope block, made it desirable to consider totally new approaches in developing and mining a number of similar areas.

Jan 1, 1971