Search Documents

By Joseph Cervik, Fred Garcia

Gob holes are routinely used by the mining industry to vent methane from gobs and to prevent it from entering the mine ventilation system. In some cases, flows from gob holes are measured by centering an anemometer on the end of the discharge pipe. These measurements are erroneous and tend to be high by as much as 30%. The Bureau of Mines determined correction factors (method factors) for anemometer measurements taken in this manner. Method factors for 10.2, 15.2, and 20.3 cm (4, 6, and 8 in) ID pipe are 0.68, 0.71, and 0.78, respectively. Comparisons between horizontal and vertical flows indicated no significant change in method factors. Consequently, the method factors for horizontal pipe flows can be applied to vertical upward flows.

Jan 1, 1987

By L. B. Phelps

Current mining regulations require revegetation in reclaiming surface nines. Excessive soil compaction can be an impediment to successful revegetation in poor soil conditions common to Eastern coal nine sites. A field study was performed to determine the bulk densities of soils that had been spread by either bulldozers or scrapers at a strip nine site. Moisture-density relationships for the soils were determined from the field samples. These were compared with stockpile samples compacted by the Standard Proctor compaction test. The results of the study indicate that the degree of compaction could be lessened through proper soil handling procedures.

Jan 1, 1986

By R. Tanaskovic

Unfavourable climatic conditions in stopes are of significant economic and social importance due to the following reasons: - Working effect is much lower leading to decreased output and work productivity disregarding implementation of mechanization. - Manpower operating capability decreases much faster under unsatisfactory climatic conditions. Under normal climatic conditions a workman would expend much less effort in line with a shorter effective time for the achievement of identical production effects since the work would be more efficacious. The objective of study of problems and climatic conditions is to make the working environment in mines suitable for normal development of operations. Lowering of mining works to increasing depths and winning of a growing number of small orebodies over a broad area makes the problem of creating suitable climatic circumstances more complex. Mining costs are growing due to bench conditions in line with decreasing metal content in the ore, so frequently the investments required for creating favourable climatic conditions represent, in addition to the selection of mining technology, a very important parameter when making decisions regarding exploitation. As known, the basic factors affecting climatic operating conditions in mines-are: temperature, humidity and speed of air flow, implying that the climatic operating conditions are closely related to mine ventilation. Usually, the concept of unfavourable climatic operating conditions includes increased mine air temperature and humidity and low air flow velocity so that heat exchange between human organism and the working environment is impeded or reduced to minimum. Metal mines in Yugoslavia are characterized by the existence of a large number of active faces - stopes and horizons and lowering of mining operations to increasing depths, so that face ventilation solutions are more and more complex. Since its foundation (1961), our Institute is engaged in investigation of factors influencing climatic circumstances improvement of calculations for air distribution and distribution control in complex ventilation networks and study of problems related to ventilation of large volume and irregular configuration faces, as well as application of gained knowledge in our mines. The paper presents the knowledge and experience gained in the case of Lead and Zinc Mine "Trepca" - Stari Trg.

Jan 1, 1980

By V. Price

Abstract: Action of certain strains of bacteria has been implicated as a significant factor in the oxidation of ore deposits. Other bacteria are thought to be significant in the formation of syngenetic sedimentary ores and in supergene enrichment processes. A normal soil/ground-water regime provides all of the necessary pH and Eh conditions for several groups of bacteria which influence the sulfur cycle in nature. Limiting concentrations of nutrients such as sulfate ions can determine whether a particular microbial species is active at a given place. In the present study, ground water was analyzed from a mineralized area and from a presumed barren area. Trace metal content of the ground water gave no well defined clue as to the presence of a sulfide ore deposit. Sulfide producing bacteria (presumably sulfate users) were found in water from about 50% of wells sampled in the mineralized area and in about 30% of samples from the barren area. These bacteria are readily detected and may provide a useful tool for regional geochemical recon-naissance. Bacterially produced sulfide ions can remove metals such as copper and zinc from solution thus complicating the interpretation of hydrogeochemical prospecting.

Jan 1, 1972

By J. E. Murphy, Y. Topkaya, R. E. Johnson, B. R. Palmer, D. K. Dysinger, R. B. Bhappu, A. E. Clark

The U.S. Bureau of Mines utilized a central composite experimental design to investigate leaching kinetics of pure chalcopyrite in the sulfuric acid-oxygen system. The six factors studied were oxygen pressures of 150, 300 and 450 PSI, leach temperatures of 35O, 65O, and 95O C, oxygen-to-chalcopyrite mass ratios of 0.5, 1.0 and 1.5, leach times of 8, 16 and 24 hours, initial acid strengths of 0.6, 1.2 and 1.8 g H,SO,/g chalcopyrite and pyrite to chalcopyrite mass ratios of 0, 1, and 2. Chemical analysis and oxygen consumption measurements indicatedthat leaching occurs through three consecutive reactions. Temperature was the primary determinant of leach rate and solution acidity was the primary determinant of oxygen consumption, sulfur oxidation, and activation energy.

Jan 1, 1993

By S. Kelebek, G. W. Smith

Four samples of galena, each prepared differently, dry ground chalcopvrite and real gar have shown various quantities of liberated sulfur corresponding up to nine equivalent monolavers on their surfaces as determined by the solvent extraction/UV analysis of sulfur using ethanol. The pretreatment of a dry ground galena sample with acidified ammonium chloride or neutral, saturated sodium chloride solutions rendered the mineral readily floatable. The collectorless floatabilities of galena pretreated with the former solution and of drv ground chalcopvrite have been evaluated in reference to the natural floatability of sulfur using the critical surface tension of floatability approach with aqueous methanol solutions. It is shown that the amount of sulfur- on these samples can be correlated with their flotation rate, which was found to he first order within the critical surface tension range. The larger the concentration of surface sulfur, the faster the sulfide mineral floats, thus, the greater its flotation rate constant.

Jan 1, 1990

By A. G. Yapo, T. W. Camm

"Mining plays a key role in the development of modern civilization as a source of essential raw materials and provider of essential fuels, producer of jobs and a factor in support of the international balance of monetary payment (Camm, 2014). Professionals in mining locate, develop, design and manage ore deposits in an environmentally safe and profitable manner. As mineral deposits become increasingly scarce, new challenges face the industry. A current trend is to an increased emphasis on underground mining techniques for deeper deposits. Operations are safer now than before as companies understand better their work environment and the importance of mining responsibly.A continual challenge for the industry is accurately reflecting the costs and selling price of ore. An enduring characteristic of mining is the situation where the market typically determines the price of a commodity; the main control a company has on the bottom line is to control the cost of production.An attempt to bring light and clarity to the cost of their business will give a better idea to investors on the true profitability of the mining business. Gold producers face this struggle to accurately reflect the cost of production while also seeking to attract the interest of the investment community (Hill, 2013). In order to have a consistent format to report on their production costs, leading gold producers, through their alliance inside the World Gold Council (WGC), worked on the adoption of a new cost framework: the all-in sustaining cost (AISC) and all-in cost (AIC).Since 1996, the traditional cash cost reporting has focused only on the mining and processing costs incurred in mining an ounce of gold, which included the costs of goods sold (labor, energy, and consumables costs) and royalties (Table 1). But cash cost reporting ignores many important aspects, like sustaining capital, general and administrative expenses and site rehabilitation at the end of the mine life (Whelan, 2013). The cash cost was used to attract many investors into the business. In fact, the high gross margin (sales minus cash costs) has been promoted in past decades by the industry instead of the net or operating margin. As a result, even when the gold price was high, nearly $61/g ($1,900/oz) in August 2011, gold producers were not reporting excessive profits in their cash flow/income statements, to the disappointment and incomprehension of investors (Milstead, 2014). The truth was simply that the other costs omitted in the traditional cash cost were reducing the apparent profits.The disconnect led to a need for more accurate cost reporting in order to win back investor confidence and provide better understanding of gold mining economics. In 2012, the senior gold mining companies, including Gold Fields, Barrick Gold Corp. and Newmont Mining Corp., worked with the WGC to develop a new measure. This resulted in the June 2013 publication of the new framework AISC and AIC, which has been widely embraced by the sector since Jan. 1, 2014 (WGC, 2013).The adoption of the new cost template would have the dilemma of showing the real profitability of gold mine properties, which might alleviate taxes from governments and legislators, but it might also scare off investors toward more lucrative industries if not winning back their confidence."

Jan 9, 2017

By Terry McNulty

There are many potential pitfalls in the commercialization of innovative technology. The failures often are remembered longer than the successes, thereby serving as deterrents to subsequent attempts. The mineral industry's future depends on effective innovation. So it is essential that the causes of failure are understood. Innovation can be examined equally well in the context of geophysics, geology or mining. However the author's experience has been in mineral processing and chemical engineering. So the following discussion is limited to processes and/or plants for producing mineral concentrates, metals or inorganic chemicals. More of what follows has to do with underachievement or failure than success. But this article demonstrates that there is a strong element of predictability in the former. Furthermore, it is a credit to the minerals industry and to the engineering profession that a very high percentage of projects succeed in achieving design capacity and forecast operating costs. Innovation means the introduction of something new. In this article, the words "innovative technology" are used broadly. They include new processes and novel combinations of established unit operations, as well as novel types of processing equipment or largest-ever equipment models. The discussion of project outcomes is based on personal experience or on published information. Citations are given for technical publications that provide either project information or insights into the methodology used to analyze project performance. However, specific projects have not been identified due to the rather negative connotations of some of the conclusions drawn about the less favorable outcomes.

Jan 1, 1998

By Robert W. Elayer

For the design of a coal mine and process plant, a comprehensive foundation of geologic information is essential. Historically, the development, collation, and use of this information for design have been costly and time consuming. With the application of a digital computer, however, the effort expended can be reduced and maximum effective use of the geologic information realized. The purpose of this paper is to demonstrate the feasibility and convenience of using a computer to Store and manipulate geologic data for use in mine and process plant design.

Jan 1, 1975

By William G. Doepken

GENERAL DESCRIPTION The Henderson mine utilizes a highly mechanized, continuous panel-caving system to extract ore from a deep, massive, molybdenum deposit. The mine site, lo¬cated 80.5 km (50 miles) west of Denver, is situated at 3170 m (10,400 ft) above sea level in a steep valley on the eastern side of the Continental Divide. The mill site, located on the western side of the divide, is linked to the mine via a 15.5-km (9.6-mile) railroad tunnel. Mine production is scheduled to reach 27 215 t/ d (30,000 stpd) from the uppermost production level. This pro¬duction rate will have been reached within the four years following an intensive ten-year preproduction development program. A second production level, due to come on stream in later years, will expand production capabilities to 31 751 t/d (35,000 stpd). The mine, which employs approximately 2000, has blocked-out ore reserves of 220 Mt (242 million st) at an average grade of 0.42% MoS2. Geology The Henderson deposit is composed of two partially overlapping ore bodies that lie 1080 m (3600 ft) beneath the peak of Red Mountain. The ore bodies are entirely within a Tertiary rhyolite porphyry intrusive complex that has intruded Precambrian granite. The de¬posit is elliptical in plan with overall dimensions of 670 x 910 m (2200 x 3000 ft). In section it is arcuate with an average thickness of 185 m (600 ft). The top of the deposit is at an elevation of 2610 m (8700 ft) while the lower limits range from 2340 m (7800 ft) on the west to below 2100 m (7000 ft) on the east. The mineralization is relatively continuous in the ore bodies and consists of molybdenite and quartz in random to subrandom, intersecting, closely spaced veinlets. Cavability RQD (rock quality designation) * values measured from Henderson drill core and compared with the RQD values from the Climax and Urad block-cave mines in¬dicated that the Henderson ore would cave but with difficulty and that a high percentage of the cave ma¬terial would be blocky. Initial caving experience shows the Henderson ore caves easier and with greater frag¬mentation than was indicated by the RQD values. Pos¬sible reasons for this are: 1) The greater lithostatic load at the Henderson has a greater effect on caving and fragmentation than anticipated. 2) The relief of confining pressure due to caving action and brittleness of the rock is enhancing breakage. Mine Layout The Henderson mine layout was designed from its inception for a large-scale, rubber-tired, continuous panel-caving mining system. The ore body is vertically divided into three major mine levels (Fig. 1). The top¬most level (8100 level), which is 2469 m (8100 ft) above sea level, is the current mine production level. The intermediate or 7700 level, which is in the initial

Jan 1, 1982

By Sidney V. Gold

Should Gold Producers Hedge Their Positions Through : Sales on Forward Markets? Purchases of Put Options? Sales on Spot Market? Forward Markets Assumptions 1. Producer has a known amount of Gold to sell in year ahead. 2. Effect on price is the same whether sold Forward or Spot Market. 3. None of us have knowledge of Future Price Trend. 4. Contange Market prevails in which Forward price premium is approximately equal to rate of interest.

Jan 1, 1983

By L. B. Phelps

Industrial mineral production is basic to life in these United States. Production techniques of these minerals are part and parcel of the training that mining engineering educators must, and do, impart to their students. This paper deals with the basic mining engineering program required by all accredited engineering schools and the specific way the Pennsylvania Scare University presents and builds upon them. The manner in which these concepts provide the student with the necessary tools to function as a mining engineer in me realm of industrial minerals extraction is discussed.

Jan 1, 1981

By N. Nemeth

The filter is an apparatus designed to hold the filter medium. At such a medium takes place the entire liquid-solid or gas-solid separation process. Hence, the medium is really the essence of filtration. Yet, the medium, an originally clean porous substance with trapped solids in it, is perhaps the most neglected part of filtration research. Basically three problems prevail at the medium: 1) Penetration of solids and their blinding of the medium and the influence of such blinding on the resistance to flow. ii) The behavior of the medium in long term repetitive filtration. iii) The filter effect phenomenon whereby the flow rate on filtering an apparently clear liquid through a medium decreases with time. This study undertakes to investigate these fundamental processes.

Jan 1, 1968

By K. S. E. Forssberg, J. A. Jirestig

Laboratory investigations on the possibility of using magnetic separation for the recovery of sulfide minerals have been reported. A survey of several sulfide ores and flotation concentrates indicated that, in most cases, magnetic separation is not a suitable primary beneficiation method. However, encouraging results have been obtained in concentrate purification. At the Boliden complex sulfide ore concentrator in Garpenberg, Sweden, an Allis-SALA Mark III carousel High Gradient Magnetic Separator (HGMS) is used with a small flotation circuit to recover sphalerite lost to the galena concentrate during lead flotation. After four years of refining the HGMS process, there has been an increase in zinc recovery and an enhancement in the quality of the lead concentrate.

Jan 1, 1994

By W. T. Caneer

Uranium may be in short supply due to the predicted energy needs in the coming years. As a result of this a new surge of uranium exploration is underway. The refinement of numerous exploration techniques has accompanied this surge. One such technique is the monitoring of radon gas in surface soils and rocks as a guide to subsurface uranium deposits. The Colorado School of Mines Research Institute became involved in radon studies in 1967 on a project for the AEC. Since that time the Institute has conducted numerous radon surveys for a large number of companies which have been active in uranium exploration. The objective of this paper is to relate the techniques utilized by the Research Institute and the results of some of the studies performed. Most of the studies performed by the Research Institute were related to roll front, sandstone -type uranium deposits. However, we have performed radon studies in various other types of rock. For those who may not be familiar with the application of radon ?sniffing" in soils and rocks, a brief descriptive background should be given. The following question may be asked -- why use radon as a guide to uranium mineralization? Some of the answers to this question are as follows:

Jan 1, 1974

By Joseph W. Leonard

Much progress has been made in the application of geostatistics to hard rock ore deposits.1,2,3 4,8 Progress in the application of geostatistics to coal deposits has developed over a period of time out of hard rock technology.5,7 Exploratory drilling in many hard rock deposits is frequently significantly more productive than exploratory drilling in coal deposits. For example, hundreds of feet of drilling and/or many drill setups are frequently necessary to obtain a few samples from a typical 4 to 6 foot thick coal seam. With hard rock deposits, which are frequently thick or volumetric, less drilling dead work is involved in sampling the deposit. To produce a variogram, which is the basic element needed for geostatistical analysis, a few well positioned holes drilled into a hard rock deposit where the core(s) can be divided into many sections can produce a detailed variogram. To produce a similar type variogram in coal, it is necessary to drill many dozens of holes with much of the core length consisting of overburden data which is frequently of only secondary importance. To apply geostatistics to coal, not only are many separate sample sites needed, but frequently a problem exists in that the interval distance between samples cannot be controlled with the ease that hard rock drilling intervals can be controlled where it is only necessary to cut core segments according to some preassigned interval of distance. Because the uses of existing coal deposit samples are frequently handicapped by irregular sample distances and lack of sampling density along certain directions needed for the development of variograms, the application of geostatistics to coal deposits frequently does not proceed with the same efficiency and rapidity as when these techniques are applied to ore deposits. Grid-fitting was developed by the writers, as a logical and evolutionary improvement over the long and successful application of geostatistics to coal seams.6,9 Grid-fitting combines the trending of variance as well as other aspects of probability theory to optimize informational yields from the commonly less productive data derived from coal exploratory programs. Grid-fitting is basically a technique where a hypothesis involving numerous grid patterns, where each pattern is of a given geometry, size and direction is repeatedly matched against actual sample data to determine which match results in the closest fit of the hypothesis to the data. To determine the closest fit, a special index known as a selectivity index was developed. The selectivity index is basically the product of the mean and variance of the variances contained within each of the grids. hence, if SI is the selectivity index then [SI = Xs E (S i - Xs) /N] where [X]s is the mean of individual grid variances Si2 for any pattern of given geometry, direction and size.

Jan 1, 1984

By Hillary W. St. Clair

In a previous report 1/the author showed that the essential information from particle size analyses of grinding mill products can be represented by three or four parameters derived from the first four moments of the particle size data. These parameters may be used in gamma or beta distribution functions to estimate the weight fraction in any given size range. Moment analysis was used to study the progressive changes that take place in particle size distribution when a homogeneous isotropic mineral such as quartz is reduced in size by impact crushing. 2/ This report briefly reviews the essential features of moment analysis and describes extension of this method to size reduction by ball mill grinding.

Jan 1, 1972

By Manuel R. Lastra

Critical to successful dump and heap leaching for gold, silver, copper and uranium are factors such as permeability, solution delivery to the ore, and solution recovery. This paper deals with possible techniques for successful accomplishment of these three factors. New developments as well as older techniques are discussed, together with rationale for use of some techniques in reference to others. The authors hope to present a checklist so that the ideal application to individual mine situations can be achieved. This involves a discussion of the merits of each different method and the situations for most logical application. It is hoped that such discussion will broaden the geographic areas where dump and heap leaching can be applied to include greater winter cold and tropical regions of large amounts of rainfall.

Jan 1, 1984

By Robert L. Gamble

The world's largest fluidized bed steam generator located at Rivesville, West Virginia is currently undergoing initial operation. This unit is designed to generate 3708 kg/s (300,000 Ib/hr) equivalent to 30 MWe of superheated steam while firing coal in a fluidized bed of limestone. Coal was first fired in this unit in December, 1976 and start up operation is progressing.

Jan 1, 1977

By Vernon N. Cox

From comments and questions concerning the meaning of USNR, and "why is the Navy in the mining business?" I believe it is worth while to establish the background and purpose of our company. We are a stock company formed by the purchase and reorganization of a company known as the U. S. Natural Gas Corporation. In May 1969, a group of investors with Mr. Robert L. Katz as president and chief executive officer, created United States Natural Resources, Inc., to develop and purposively use our Natural Resources in four areas: 1. Mines and Minerals 2. Forest Products 3. oil and Gas 4. Recreational Lands As final proof that we are not a government organization, I simply state. "We pay taxes." The mining division was formed in October 1969, with the completion of the merger of USNR and Vibration Measurement Engineers, Inc., Of Evanston, Illinois. Throughout the industry we were known as "VME," our company supplied consulting service in the field of seismic energy control, mining consulting and. we operated drilling, blasting and, contracting organizations in several areas of the country. Since that time we have developed and acquired producing properties in Quarrying, Coal Mining and Cement Copper Production.

Jan 1, 1971