Search Documents

By Jerry G. Rose

This paper addresses a process by which both the disposal and utilization of preparation plant coal refuse can be simultaneously accomplished with an attendant benefit of significantly increasing the percentage of extractable coal. A laboratory study is described in which coal refuse was successfully utilized as an aggregate in low cost concrete (coal-crete) mixes under simulated mine environments. Coal-crete specimens with compressive strengths of 14,000 kPa (2,000 psi) were consistently produced. A construction sequence and mining plans are offered for placing the low-cost coal-crete pillars in accessible areas in room-and-pillar mines so that a Substantial portion of the remaining coal pillars could be extracted. The method could be applicable in areas where mining procedures do not permit pillar extraction because of possible surface subsidence, roof problems, or other conditions. Possible structural difficulties with the coal-crete pillar support system are discussed. Using a discounted cash flow analysis, the economic feasibility of mining with the coal-crete pillar system is investigated. The cost of the coal-crete pillar system is compared to the cost of a mining system which would have less coal recovery. The analysis indicates that although at higher coal selling prices the coal-crete mining system may yield an acceptable rate of return, the alternative of leaving the coal pillars is more attractive at the present time.

Jan 1, 1977

By Eduardo Poltronieri Trés, Anderson Denadai Thomazini, Rodrigo Boyer Fernandes, Francisco de Assis Dutra Macedo, Gilvandro Bueno, Maycon Athayde, Rossano Augusto Pilon Nunes

The earliest industrial application of high pressure grinding rolls (HPGR) at comminution was in 1984 in the cement industry. Since then, the equipment has been widely applied in mining activities. Despite the rapid spread across the industry, several challenges are still present in the equipment’s application, especially considering the complex ore breakage behaviour reported for this process. The pellet feed’s HPGR comminution was recognized as fundamental to efficiently increase the particle surface area (e.g., blaine specific area, BSA) at a lower energy and water consumption level (Chapman et al. in J Southern Afr Instit Mining Metall 113:407–413, 2013). The present study considers a novel milling process applying only HPGR as a re-regrind stage after concentration. The amount of successive ground product recirculation into the machine to achieve the required particle size for the pelletizing process was investigated. The study compared the ball wet milling process with the innovative processing technology for hematite–goethite ores. Green pellet balling and induration processes were simulated in bench and pilot scale. The milling results showed a considerably steep increase in BSA after each recirculation step into the HPGR, although compared with the ball-milled product the size fraction <45 μm% increased a modest five percentage points after three recirculation cycles, remaining steady until the last recirculation step. As a result, the green pellet generated presented higher concentration of pellets between 10 and 16 mm (%10-16 mm), with a higher drop number than typically observed when produced with ball-milled feedstock. Consequently, on the induration process, a higher pellet deformation was observed during the pot grate loading. Despite that, the fired pellets still presented an outstanding performance in cold crush strength (CSS) considered suitable to an industrial application.

By J. Georgi

A number of infrastructure projects are on progress all around Greece at the moment. The common propose of these a project is the promotion of quality in: Design, construction and maintenance stages. They also comply with environmental management, which is, a method of organizing and implementing environmental protection measures. The paper includes by special reference on two important modern transport infrastructure projects for the development of Greece and its communication with Europe and the Balkans. Their landscape types and natural vegetation, local climate, geological conditions, altitudes, aspects and soil types vary As a result, upland landscapes in particular, are endangered. Due to the complex of nature of this environment, the development and the landscape design of the projects is a high challenging task. Wherever the nature of the projects requires intervention to the environment, they intend to follow the direct restoration of landscape and method for ecological balance. The implementation of landscape design of infrastructure projects, aims at restoring the landscape affected by construction works, incorporating transport works into the landscape, emphasizing on areas of particular interest (e.g. archaeological sites), while at the same time observing the principles of an efficient operation and safe use of the alignment. Landscape design provides, among others for the protection of slopes against surface erosion and the reinforcement of their stability, the improvement of road functionality, the aesthetic improvement of the landscape, adaptation of the road landscape to the greater environment, visual guidance of the user, screening of lights of the vehicles moving in the opposite direction, the protection against wind etc. The landscape design strategy and landscape applications are specified by special landscape guidelines and specifications that can be considered as part of the sustainable development of a alignment creating a high a esthetic scenery, ensuring the security of transportation and the environmental protection.

Jan 1, 2002

By D. Hodouin

Abstract. Dynamic experiments were performed in a continuous open-circuit 40x40 cm ball mill using a pseudo-random binary sequence of the feed rate and measuring the variations of the discharge particle-size distribution. The impulse response is calculated by a cross-correlation technique. Then a model involving a discrete transfer function and a time-series stochastic equation is calibrated using maximum likelihood methods. Based on this empirical model. a minimum variance controller with constrained input is designed and its performances are compared. by simulation, to the performances of a conventional PID regulator.

Jan 1, 1987

By Laurence M. Demers, Douglas C. Kuhn

It has been suggested that radicals on the surface of dust particles are key chemical factors in the pathophysiology which results from the occupational inhalation of coal and silica dust. In addition, oxygenated derivatives of arachidonic acid (eicosanoids) have been implicated as important biochemical mediators of mineral dust-induced lung disease through their role in bronchial and vascular smooth muscle reactivity, inflammation, and fibrosis. Therefore, we assessed eicosanoid production by the rat alveolar macrophage (AM) exposed in vitro to mineral dusts with varying surface chemical characteristics in order to determine if radicals associated with the mineral dub1 could influence the production of pro-inflammatory mediators in the lung environment. Rat AM were exposed to freshly fractured or "stale" bituminous coal dust, as well as untreated silica or silica calcined to 500°C and 1100°C. Prostaglandin E2 (PGE2) and thromboxane B2 (TxB2) levels in incubation medium were determined by specific radioimmunoassay. When AM were exposed to freshly fractured coal dust, PGE2 and TxB2 production were markedly increased. In contrast, exposure of AM to "stale" dust significantly reduced PGE2 and TxB2 production. In vitro exposure of AM to untreated silica resulted in a significant increase in PGE2 and TxB2 production compared to control. However, exposure of AM to silica calcined to 1100°C resulted in eicosanoid levels which were not significantly different from control. These findings suggest that radicals associated with respirable coal and silica particles may play a key role in the ability of mineral dust to activate AM eicosanoid production.

Jan 1, 1991

By Steve Kral

The Fourth International Symposium on Hydrometallurgy was organized to give those in the minerals processing field an opportunity to discuss current topics of interest in the broad field of hydrometallurgy. Held in Salt Lake City, UT Aug. 1-5, 1993, this fourth symposium also paid tribute to Milton E. Wadsworth for his many contributions in this area over the past 40 years. The science of hydrometallurgy has made great strides since the last symposium was held 10 years ago. The use of electrochemical principles and techniques has produced encouraging results. For example, the application of in situ electrode spectroscopy has helped to understand the mechanisms operating in hydrometallurgical processes. Sophisticated computer models have been developed to handle the thermodynamic properties of concentrated electrolytes. However, it is up to the hydrometallurgist to continuing working on bridging the gap between theory and practice. The successful application of solvent extraction-electrowinning (SXEW) is one illustration of the successful transfer of technology. Its widespread use in the United States during the 1980s played a significant role in the revival of the domestic copper industry. Currently, electrowon copper accounts for about 30% of total US production. Impressive developments in precious metals recovery have also occurred. Since the last symposium, carbon-in-pulp (CIP) and heap leaching have become widely used in gold recovery. And recovery of refractory precious metals ores and concentrates by pres¬sure oxidation and bio-oxidation have made significant advances. In all these examples, hydrometallurgy has played a significant role in the recovery of minerals and metals from primary sources. In addition, considerable attention has been focused on the treatment and recovery of values from secondary sources.

Jan 1, 1994

By Juan L. Sepulveda

An MPSI KW-20 Tower mill has been tested at the Butte Molybdenum plant of Anaconda Minerals Company, as a substitute for the conventional 1.5x3.0 m (5x10 ft) tumbling ball mill currently used for regrind purposes. The Tower mill was operated in both open and closed continuous circuits. These results were complemented with a series of batch grinding tests to determine some of the operational features of this mill. The relative grinding efficiency of the Tower mill with respect to the tumbling ball mill was determined and the applicability of this new mill to a plant/heavy duty environment was assessed. Experimental results obtained on the regrind of moly concentrates indicate that approximately 40% energy savings can be realized by using the Tower mill instead of the ball mill.

Jan 1, 1984

By James Charles McHardy

During 1980-2000, the Florida Phosphate industry will deplete its Central Florida Polk County reserves. As a result, new mines will be built in the ?so-called? Southern Florida Reserve areas. These new mines will require new mining, beneficiation and tailings disposal technologies in that the southern reserves have different characteristics than have been encountered in the Central Florida deposits furthermore, government regulations will necessitate the development of new tailings and clay disposal methods. This paper reviews these challenges for the phosphate industry and how these opportunities can be expected to effect plant design and plant operating practices.

Jan 1, 1981

By Alain A. Sonntag

The MBS Solvent Extraction System utilises a unique design of mixer- settler having very high capacity per unit area and great flexibility. The development of the mixer-settler is traced through its various stages wherein the independence of mixing and pumping, reduction in settler area requirements and simplicity of plant layout were achieved. The laboratory, pilot plant and full scale tests contributing to the development of the machine are described. The existing KREBS SX plants in Europe and Africa are described as well as the plants presently under design. Results of recent testwork are also given.

Jan 1, 1981

By V. F. Hollister

Copper and gold were discovered in the Copper Canyon area of the Battle Mountain district of Lander County, Nevada, in August of 1866. By 1876 a gravity plant was con¬centrating oxidized Copper Canyon copper-gold ores. The history of mining in the district to 1967 has been summarized by John E. Frost (in press) as a case history of the discovery of the Battle Mountain porphyry copper deposits. His summary is not repeated here; rather, the present case history covers exploration since 1967, primarily for gold ores. Subsequent to the construction by Duval of facilities to mine the porphyry copper deposits in 1967, Duval established a geologic staff at the mine to continue district exploration. The staff was guided by David W. Blake, who acted as chief geologist for Duval&apos;s exploration in this part of Nevada. Blake&apos;s activities led to the publication of numerous technical articles, including his contribution to the US Geological Survey Professional Paper 798-B. A part of that volume is attached as a reprint (pages 23 through 66) as an explanation of the geological setting of mineralization in the district. The work by Blake and his staff recognized metal zonation in the skarn environment at Copper Canyon, and their studies were incorporated in the development of the Tomboy-Minnie gold deposits that are peripheral to the porphyry. Exploration continued beyond the immediate vicinity of the porphyry and the Fortitude ore zones were discovered. These skarn deposits are described in the attached article by Wotruba, Benson, and Schmidt, published in the July 1986, MINING ENGINEERING. The continued exploration successes at Battle Mountain reflect on the well organized and effective exploration team developed at the mine. The team has provided successive discoveries in a district known mostly for ore bodies that are exhausted in a few years&apos; time.

Jan 1, 1990

By R. C. Bunge

Many minerals float best with fatty acids in the intermediate pH range. For example, fluorite, a semi soluble salt mineral, exhibits a maximum contact angle and a maximum flotation recovery in the pH range of 6-8 after conditioning in a palmitate solution (fig. 1). The maximum in flotation coincides roughly, as many researchers have observed, with the boundary of bulk precipitation of the fatty acid. According to fig. Z this boundary is in the above case of 5xl0-7 M palmitate approximately at pH 6.3. For assessing the phenomena occurring at the bulk precipitation boundary of fatty acids, the surface tensions of carboxylate solutions have been measured under various conditions. Fig. 3 shows the surface tension development of palmitate and myristate solutions of increasing concentration at pH 12. Also shown are the bulk precipitation edges (BPE) of the respective solid species that is stable under these conditions, that is the potassium acid soap, HKAZ. Both curves display a similar behavior. As the concentration of carboxylat,e increases, the surface tension decreases, until a minimum is reached at which the curves level off. The decrease of surface tension with increasing carboxylate concentration is generally taken to indicate the surface excess of the carboxylate ion. The point where the curve suddenly levels off has not yet been explained. While it is well known that the onset of micellization (CMC) may cause such an inflexion of the surface tension curve, this cannot be the case here because the position of this point depends, as shown in fig. 4 for palmitate, on pH (the CMC is generally independent of pH). We believe that this point indicates the precipitation of a colloidal acid soap (colloidal precipitation edge, CPE) before the bulk precipitation of this species sets in (BPE).

Jan 1, 1994

By R. L. Godfrey

The Custom Coals advanced coal cleaning plant will be designed with a unique blending of existing and new processes to produce two types of compliance coals: Carefree Coal? and Self-Scrubbing Coal?. Carefree Coal will be produced by cleaning the coal in a proprietary dense media cyclone circuit utilizing fine magnetite to remove up to 90 percent of the pyritic sulfur and correspondingly greatly reduce the ash. While may utilities can achieve full S02 reduction compliance with Carefree Coal, others face higher sulfur reduction requirements due to the higher sulfur content of their existing fuel supplies. For these circumstances, a patented Self-Scrubbing Coal will be produced by taking Carefree Coal and pelletizing limestone-based additives with the finest fraction of the clean coal. These technologies will enable over 150 billion tons of non-compliance U.S. coal reserves to meet compliance requirements.

Jan 1, 1995

By Lawrence W. Teufel

Knowledge of in situ stress and natural fracture distribution at depth improves our ability to stimulate and produce low permeability reservoirs. The focus of this study is three closely spaced, 2.5 km deep vertical wells in the Piceance Basin of Colorado. The wells were completed through the tight lenticular and blanket gas sands of the Mesaverde Group. In situ stress directions and magnitudes were determined from hydraulic fracture tests and anelastic strain recovery measurements of oriented core. The distribution, orientation, and characteristics of natural fractures in the subsurface were determined from detailed observations of over 1300 m of core, of which 400 m was oriented. Stress measurements clearly show that horizontal stresses are strongly influenced by lithology. In a sandstone/shale sequence at a depth of about 2.0 km in situ stresses in sandstone formations are anisotropic, with the average ratios of the minimum and maximum horizontal stresses to the overburden stress being 0.82 and 0.96, respectively. In sharp contrast bounding shale formations are lithostatic. This stress contrast between sandstones and bounding shale formations could act as a barrier to hydraulic fracture propagation during stimulation and impede vertical fracture growth. Natural calcite-filled fractures are present in over 7 percent of the core, with several horizons having a much higher frequency of fractures. Fractures are found primarily in sandstone. The fractures have a strong preferred orientation of N 1060E[+]110, which is aligned with the maximum horizontal stress and direction of hydraulic fracture propagation. The interaction between a well developed fracture fabric and anisotropic stresses in sandstone formations produces a permeability anisotropy, with the maximum permeability aligned with the fracture fabric and maximum horizontal stress.

Jan 1, 1986

By S. Bhamidipati

Abstract. Controlled flow is an aspect often desired in mine ventilation. This is normally obtained by using fans and regulators to achieve the required pressure balance in the system. Preference for a certain network layout of these control devices is influenced by technical as well as legal and economic factors. In this study, a model is developed based on an economic criterion by which an optimum layout of fans and regulators for a controlled flow system can be determined. The concept is analo¬gous to the critical path crashing. However, a linear programming package is used to demonstrate the solution procedure for a hypothetical venti¬lation network.

Jan 1, 1983

By Ray E. Harris

A resource of 134,400,000,000 tons of minable trona and mixed trona and halite underlies an area of about 1,300 square miles vest of Green River, Wyoming (Culbertson, in preparation)(Figure 1). In 1982, the total domestic consumption of soda ash (refined trona) was 6,667,000 short tons (Kostick, 1983), approximately 90 percent of which came from Wyoming trona. This enormous resource occurs in the Wilkins Peak Member of the Creen River Formation (Eocene). The Green River Formation is derived from sediments deposited in a large lake (Lake Gosiute) that occupied the Green River Basin in south-western Wyoming 38-54 million years ago. The Wilkins Peak Member represents a restricted, evaporite-rich cycle of deposition during which time the trona deposits were formed. A total of 42 trona beds are known, of which 25 are of sufficient thickness and extent to be considered minable (Culbertson, in preparation).

Jan 1, 1984

By Gerald W. Cormick

In a complex society such as ours, the range of "negotiating" relationships is constantly increasing. These negotiating relationships have emerged as a direct result of the diffusion of power or influence to new sectors and emerging concerns. Even within organizations, the myth of the authority-based heirarchical structure has given way to the reality of constant negotiations between superior and subordinate and with peers in the organizational structure. In the broader context, the corporate organization finds it necessary to reckon and often negotiate with organized employees, suppliers, buyers, government agencies and a range of organized private interests ranging from minority groups to environmental organizations. In response to this diffusion of power and the conflicts which it has engendered, a variety of conflict avoidance, conflict managing or conflict resolution techniques has developed. The purpose of this paper is to attempt to differentiate between some of the conflict intervention approaches which have appeared "on the market", and to suggest three bases for selecting among them: 1. The "role" of the conflict intervenor; 2. How far the conflict has developed; and 3. The breadth and impact of the issues involved.

Jan 1, 1979

By J. M. Marek

The determination of the proper cutoff grade for an open pit metal mine is based on economic criteria and the operating philosophy of the mining company. Previous papers have dealt with the balance of a fixed mine production capacity versus economic return. Mine production capacity is often controlled by the amount of mining equipment and the working area in the pit. A complete cutoff grade strategy is a balance of economic return of mining higher grade material versus the capital costs of additional production capacity and the operating cost of moving the waste and low grade material to assure proper ore release. An approach to the problem is presented which is based in part on work by previous authors and provides guidelines to proper cutoff grade strategy encompassing the time value of money and variable commodity prices.

Jan 1, 1985

By Frank C. Appleyard

As the environmental movement gained force during the past few years, it was inevitable that attention would be focused on surface mining, and we have seen this method of extracting minerals from the ground come under heavy attack by conservation groups, the press and television, legislators at all levels of government,, and the public at large. It is difficult, and in some situations, perhaps impossible, to measure either the need for, or the results of, land reclamation in absolute terms. Therefore, much of the criticism of surface mining has been based upon subjective analysis rather than hard data, with the result that discussion of the subject often includes a fair amount of emotional response. To be fair, this reaction is not limited to just our critics; even we hard headed engineers sometimes respond in the same way, an observation with which you may agree when I finish this talk. This leads to the thought that whether you are for it, or against it, land reclamation in many respects is a state of mind. That is, our reaction to it can vary considerably, depending on how far we have thought it through. And think it through we must, because the pressures being brought to bear need to be met with positive actions if the problem is to be brought under control, and in the next few minutes I would like to discuss from a management point of view some ideas which might aid in this thinking process. It would be a mistake, I believe, to think that the current energy crisis will suddenly bring the environmental movement to a stop, and therefore, we can relax and go back to running our busi¬ness the way we used to. This is not realistic; on the contrary the energy crisis is focusing attention on the limitations of our natural resources as nothing else could, and with respect to land

Jan 1, 1974

By Jeffrey J. Daniels

Advances in borehole geophysical research for mineral assaying, and remote detection of mineralization away from the borehole. Nuclear activation measurement research has provided accurate in situ assays of economic metals with neutron-gamma activation, using a high resolution intrinsic-germanium detector. Although nuclear activation analysis is the present "best-hope" for obtaining in situ assays for some elements, gamma-gamma and magnetic susceptibility measurements can provide accurate assays for lead-zinc and magnetite, respectively. Borehole optical spectroscopy and x-ray fluorescence are being investigated as possible in situ assaying techniques for some minerals. More laboratory and field calibration research is needed before nonlinear complex resistivity (NLCR) can be routinely used as a quantitative assaying tool. Field tests have shown that variations in the local geologic environment can affect the quantitative accuracy of assay values from downhole NLCR measurements. Deeply penetrating borehole geophysical methods are increasingly being used for mineral exploration as drilling costs and exploration have increased. Borehole electrical measurements have been shown to be useful for detecting conductive orebodies that are not interesected by a drillhole. Hole-to-surface resistivity, and surface-to-hole time-domain electromagnetics are demonstrated to be particularly effective for defining mineralized zones in a massive sulfide environment. Borehole gravity meters and three-component magnetometers have been developed and should prove useful for defining geologic anomalies away from the drillhole.

Jan 1, 1985

By Immo H. Redeker

This is a final progress report on a cooperative project conducted by three private feldspar companies,** North Carolina State University, and the federal Bureau of Mines. The object of the project was to reduce the feldspar tailings disposal problems at the flotation plants in the Spruce Pine area of North Carolina. The initial phase of the project revealed that high tonnages of saleable feldspar and quartz were lost in the tailings and the three feldspar companies are now concentrating their efforts on feldspar recovery, either by reclamation from the tailings as suggested by the Asheville Minerals Research Laboratory or by improvements in metallurgy in the existing plants.

Jan 1, 1970