Search Documents

By James M. Stauffer

There are many types of filters designed to separate a solid from a liquid, including plate and frame presses, pressure leaf filters, gravity filters and vacuum filters. This discussion will be limited to continuous vacuum filtration and, specifically, to continuous rotary vacuum disc filters, drum filters and horizontal belt filters. The use of vacuum filtration can be advantageous in that: 1. The feed slurry can be delivered to the filter either by gravity or by a simple, inexpensive low pressure pump that only has to overcome the resistance of the feed piping system. 2. The filter equipment does not have to withstand high pressures. Consequently, a wide range of materials of construction, including plastic and fiberglas reinforced polyester (FRP), can be used in the fabrication. 3. After the form time, the filter cake is exposed to the atmosphere and the cake is accessible for further operations such as mechanical or physical dewatering, washing, and sampling on a continuous basis. 4. The discharge of the dewatered solids is continuous for directly feeding to the next operation; for example, a dryer. 5. Various methods of discharge can be fitted to the filter to effect optimum discharge of the dewatered cake solids. The principal of operation of a vacuum filter, regardless of type, is basically the same. The filter incorporates a filter medium supported on a drainage system and arranged so that the mixture to be separated (feed slurry) can be introduced to one side of the filter medium on which the solids are trapped and through which the liquid (filtrate) flows due to the applied vacuum.

Jan 1, 1979

By Richard E. Lounsbury

Coal mine refuse handling traditionally has been the redheaded stepchild of the industry - a problem to be ignored as much as possible. During the past few years, however, mining companies have become more aware of the potential water pollution problem associated with refuse handling and storage. Planning for refuse disposal increasingly emphasizes protection of the environment as well as economics of refuse handling. Coal companies are responding to the environmental control needs by devising new systems and adapting well-known techniques to refuse handling systems. Monterey Coal Company has operated a non-polluting refuse disposal system at its No. 1 Mine for over two years. The purpose of this paper is to describe the design considerations given to the planning of that system and the operational experience gained during its construction

Jan 1, 1973

By James H. Williams

More than 100,000 residents of Springfield and surrounding communities live on karst (sinkhole) terrain on the Springfield Plateau in southwestern Missouri. The city occupier much of the headwaters area of Wilson Creek basin, which is underlain by the Burlington Limestone (Mississippian), a cavernous, massively bedded formation averaging 150 feet in thickness. Sinkholes, some as deep as 75 feet, pock-mark the uplands. Stony red residual clay mantles the pinnacled limestone bedrock. Surface water lost to sinkholes and losing reaches of upstream areas resurges in springs and estevellas (reversible sinkholes) in the lower reaches of Wilson Creek. The Springfield Southwest Treatment Plant, an activated sludge process sewage treatment facility, situated about mid-basin at the confluence of Wilson Creek and a tributary, South Creek, serves the entire city. Effluent from the treatment plant together with industrial, street-wash and other waste from the-headwaters of the basin have degraded both surface and ground water quality in much of the Wilson Creek watershed. The area affected includes Wilson's Creek Battlefield National Park and recreational reaches of James River below the mouth of Wilson Creek.

Jan 1, 1970

By Michael Edesess

The salt gradient solar pond has been the focal point of accelerating international attention and interest in recent months. Only recently have most investigators in the renewable energy field come to realize the versatility of the solar pond, and its ability to overcome certain problems usually associated with solar technologies. These realizations, together with clear demonstrations in Israel and elsewhere of its technical feasibility, have combined to bring the solar pond to the forefront of renewable energy technologies. The solar pond is a natural or site-built pond, about one to five meters or more in depth, which has been altered to retard the loss of absorbed solar energy. The absorbed solar energy is usually lost through upward buoyancy of the warmed water, followed by the loss of its heat to the atmosphere. The chief solar pond technology -the salt gradient, or "nonconvective" solar pond-prevents this upward buoyancy by means of a vertical density gradient achieved with dissolved salt. The deep waters in the solar pond reach high temperatures, up to and even above the boiling point of pure water.

Jan 1, 1981

By R. J. Weigel

The Santa Fe Railway serves the dominant U. S. potash producing region which is centered at Carlsbad, NM. This rail system extends over 12,000 miles stretching from Chicago to the Texas Gulf Coast to the state of California. (see Figure 1) Since Carlsbad mining operations began in the 1930?s, Santa Fe has been transporting potash to many of the important grain producing areas of the country and to the major ports in Texas and California. Santa Fe has maintained a close relationship with the potash companies and has adopted a marketing philosophy of attempting to maximize opportunities for the Carlsbad producers where it is mutually beneficial. Potash has been an important commodity for the Santa Fe. It accounted for 8% of our revenue in 1965 and 3% in 1984. In the 1950?s, Carlsbad became the second largest revenue producing point on the Santa Fe. But this prominent position has diminished as ore reserves became depleted, imports flooded the U. S. market, and truck transportation developed.

Jan 1, 1985

By J. T. Graves

Bauxite, dolomite, and magnesite are natural occurring minerals that are used extensively in the manufacture of refractory products. In addition, magnesia produced from seawater or brine finds its way into the production of refractories. All of these materials must be processed at high temperatures, 1500°C to 2200°C, to produce an intermediate raw material (refractory grain) , which can then be used in the final manufacture of refractory bricks and shapes. During the last 20 years, the major supply of refractory bauxite has been from Guyana, and at times the annual production has ranged up to 1,000,000 tons per year. More recently, China has become a major source of refractory grade bauxite by supplying over 300,000 TPY. Other sources of bauxite in lesser quantities have been Surinam, Brazil, and the U.S.A. During 1980, the estimated available world tonnage amounted to slightly more than 1,300,000 tons. The bulk of this material has been calcined in rotary kilns except for some of the Chinese production, which was treated in shaft kilns. Recent work has indicated that an excellent product can be produced in the Nichols Shaft Kiln using much less fuel than the conventional rotary kiln. Details of the Nichols Shaft Kiln will be provided later in this paper.

Jan 1, 1982

By Franklin H. Sharp

During the last few years the New Lead Belt of South- eastern Missouri has become the main source of lead in the United States. It also produces significant amounts of zinc, copper, and silver. The mines are located on a narrow, mineralized trend extending southward from Viburnum, Missouri for about thirty-five miles. The area is part of the Ozark uplift and consists of steep-sided, heavily wooded hills with narrow valleys. Surface streams are very erratic, normally having low flows but becoming rushing torrents during the violent thunderstorms that occasionally occur. Because of the pristine nature of the country and the newness of the mining developments, the environmental impact of all phases has been closely watched.

Jan 1, 1973

By G. W. Mannard

The large massive sulphide deposits present a formidable challenge to the economic geologist. They represent such huge concentrations of iron, sulphur, base metals and precious metals that it is difficult to conceive how they were derived from the crust or mantle of the Earth. The problem of the origin of massive sulphide deposits has generated a geological controversy which has lasted two hundred years and shows no sign of abating. The economic incentive to solve this problem is great, as the massive sulphide bodies are the moat important source of the world's zinc, lead, and silver, as well as yielding large amounts of copper and gold. Using the criteria of abundance, size, age distribution and gross value of contained metals, the predominant sub-group of the massive sulphide deposits is that which comprises the crudely conformable pyritic (or pyrrhotitic) deposits which occur in stratified volcanic and sedimentary rocks or their metamorphosed equivalents. Examples of this sub-group are: the Buchans, Bathurst, Noranda, Kidd Creek, Flin Plon and Sullivan deposits of Canada; the Mt. Isa and Broken Hill orebodies of Australia; the Cyprus, Rio Tinto, Meggen and Rammelsberg deposits of Europe; Ducktown and the United Verde in United States; and the Kuroko deposits of Japan.

Jan 1, 1973

By W. M. Houston

The phosphate formations of the Pliocene epoch were deposited along the coastal shelf of the eastern seaboard. The deposition of the phosphate is thought to be somewhat contiguous along the early shoreline, and the deposit can be more or less traced over an 800 to 930 mile path from the Florida Gulf Coast, near Ft. Myers, to the Pamlico Sound of North Carolina. This is illustrated in Figure 1. Three areas of commercial importance are currently being exploited from this extensive known deposit: 1 - The so-called ?Bone valley? in Central Florida (multiple operations) 2 - Hamilton County in North Florida (Occidental Corporation operation) 3 - Beaufort County in North Carolina (Texas Gulf Sulphur operation)

Jan 1, 1966

By E. A. Sigworth

Our interest in metallurgical applications for activated carbon was thoroughly aroused when laboratory studies indicated that each dollars worth of carbon could retain as much as four dollars worth of tin. Since then other data was developed suggesting many Potential uses in the metallurgical field it is hoped that, the information presented in this paper may encourage studies by knowledgeable individuals in metallurgical operations. Activated Carbon accomplishes its results by adsorption which involves selective removal of materials from solution by holding the compounds on the carbon surface at the active areas. An example of adsorption is the dyeing of cloth where the dye is selectively held on the cloth surface and the concentration in the dye solution is thereby reduced. Many theories exist on, adsorption, but the predominant factors involved in metallic ion adsorption probably are that adsorption is indirectly proportional to solubility and is benefited by high concentrations acting to squeeze out molecules in smaller amounts.

Jan 1, 1962

By D. Blackwell, W. R. Reed, G. Ross, S. Peters, M. Shahan

Dust collectors for roof bolting machines generally use a dry box to collect the roof bolting material. Recently, an underground mining operation converted a dry box dust collector to a wet box dust collector with a unique exception from MSHA for testing purposes. Water is routed to the roof bolter from the main water line of the continuous miner. The wet box utilizes a water spray to wet the incoming material. Testing was conducted comparing the two different collector types. Respirable dust concentrations surrounding the roof bolter with the different collection boxes were similar. The main difference in respirable dust concentrations occurred when cleaning the dust boxes. The average respirable dust concentration during cleaning of the wet box was 0.475 mg/m3, and during the cleaning of the dry box the average respirable dust concentration was 1.188 mg/m3. The silica content of the roof material was high, ranging from 28.9% to 52.7% during this study. The results from this study indicate that using the wet box as a collector reduced exposure to respirable dust up to 60%when cleaning the collector boxes. INTRODUCTION Currently, the dry vacuum dust collection system is the standard dust collector on roof bolters in underground coal mining. It has been proven to be an effective dust control to prevent roof bolter operators’ overexposure to coal mine respirable silica dust during roof bolting operations [Potts eta l, 2011 and Colinet, 2013]. The dry collection system works as follows: drill cuttings are vacuumed into the precleaner. The precleaner dumps oversized material onto the mine floor while undersized material enters the dust box via vacuum airflow produced by a blower. The cuttings entering the dust box are either deposited on the floor of the dust box or into a dust collector bag. The vacuum airflow leaves the dust box through a final filter which removes any small particles from the airflow. Figure 1 shows the internal view of two dry collection system boxes; one that does not use the dust collector bags and another that uses the dust collector bags. Dust collectors that use dust collector bags to contain material inside the dust collector box have been shown to provide better protection to roof bolter operators than dust collectors that do not use the bags [Listak and Beck 2008]. The dry collectors are very efficient at reducing respirable coal mine dust exposure from roof bolting activities. Recently, Blue Mountain Energy’s Deserado underground coal mining operation, outside Rangely, CO, made a modification to the dry collector system to convert it to a wet collector system with a unique exception from the Mine Safety and Health Administration (MSHA) for testing purposes. The wet collector system still uses a vacuum system to pull material from the vertical roof bolt hole, but incorporates a water spray nozzle located inside the dust box to wet the incoming material. The flow through the nozzle ranges from 1.9–7.6 lpm (0.5–2.0 gpm) at 0.69 MPa (100 psi). The conversion to the wet collector system removes the precleaner and the cyclones inside the dust box. The wet material (sludge) then empties through a specialized valve in the bottom of the box. The final filter is still used to prevent respirable dust from leaving the dust box through the exhaust. During operation, the wet collector dust box is opened and hosed clean after roof bolting every place. After every two entries the final filter is changed out. Figure 2 shows the inside of the wet collector box.

Jan 1, 2019

By E. J. Rogans, W. N. Cartner

Carbon technology has largely superseded filtration plants as the more acceptable gold recovery technology. This has, over the last two decades, provided a tremendous driving force for the development of new equipment. One of the main focus areas of this technological development is the development of effi­cient interstage screening systems. Several variations of exter­nal and internal screens are available, with the more recent shift away from air cleaned units to mechanically swept units. This paper discusses the development of one such mechanically swept interstage screen and how the development led to the suc­cessful implementation of a carousel type of CIP operation. The first generation Pump-cell emerged as a consequence of the success achieved with the mechanically swept NKM screen, The idea was to modify the screen to incorporate the functions of pumping, screening and agitation in a single drive unit, the screen generating sufficient lift for interstage slurry flow so that all contactors would be at the same level. This sys­tem was further incorporated as a high intensity modular CIP contactor, i.e. low slurry residence times combined with high carbon concentrations. A discussion on the kinetic gold adsorp­tion theory and its manipulation in the design of the pump-cell concept is discussed in a paper published in a previous Randol Conference< 1), Testwork carried out at Vaal Reefs proved the concept of the Pump-cell on a pilot plant scale<2), which resulted in the building in 1990 of the first large Pump-cell plant at West Witwatersrand Gold Mine designed to treat 340m3 of pulp per hour and , even though the plant operated successfully with respect to gold recovery performance, a few problems were experienced with the basic engineering design(3),

Jan 1, 1996

By Jr. Zink

An economic and operational evaluation of the unrecovered metal, physical conditions, and chemical environment in a leach pad should be made prior to decommissioning. This evaluation will help determine the possibility and method of secondary and/or enhanced metal recovery and the method(s) to be used for detoxification and heap closure. The evaluation requires quantitative sample collection in a locally variable, yet grossly homogenous material. An assessment of a valley fill heap leach pad was made using a technique borrowed from placer technology called sonic drilling. The sonic drilling technique produced very satisfactory core recovery and sample quality. At this site, drilling results demonstrated that the method of heap construction produced expected features after extensive long term leaching. Rather than a uniformly homogenous pile of metallurgically depleted crushed ore, an assemblage of solution channels, un-oxidized sections, unleached areas, and compaction due to various factors, were found. These conditions are thought to represent a normal, rather than unique, situation for a valley fill heap leach. The lack of this information can have a significant impact on the economics and methods of heap re-handling and ultimate closure.

Jan 1, 1992

By Silas Li, Michael Harris-Gifford, Jason Choi, William H. Hansmire

Twin-bore tunnels with a single track in each tunnel are currently the most common subway tunnel configuration. However, a large diameter single-bore tunnel with two tracks separated by a center wall could replace twin-bore tunnels and introduce potential benefits but require necessary modifications to the subway system. In particular, a nominal 40-foot-diameter single-bore tunnel can be considered in lieu of nominal 20-foot-diameter twin-bore tunnels. This paper discusses the benefits and modifications introduced by replacing twin-bore tunnels with a single-bore tunnel, with respect to various elements of the subway related to the tunnel, stations, track, and tunnel systems.

Dec 1, 2022

By Richard A. Thomas, Liming Yuan, Wei Tang, JOHN SOLES

Lithium-ion battery applications are increasing for battery-powered vehicles because of their high energy density and expected long cycle life. With the development of battery-powered vehicles, fire and explosion hazards associated with lithium-ion batteries are a safety issue that needs to be addressed. Lithium-ion batteries can go through a thermal runaway under different abuse conditions including thermal abuse, mechanical abuse, and electrical abuse, leading to a fire or explosion. The NIOSH Mining program is conducting research to prevent and respond to lithium-ion battery fires for battery electric vehicles in the mining industry. In this study, experiments were conducted to investigate the effectiveness of different suppression systems including dry chemical, class D powder, and water mist for lithium iron phosphate battery pack fires. The effects of activation time and release time of the water mist system on the suppression of lithium-ion battery fires were studied. The results of this study may be helpful for developing strategic firefighting and response plans for battery-powered vehicles used in mining.

Feb 17, 2024

By John Dodd

Corrosion studies in laboratory ball mills and grinding environment simulations produce corrosion rates and total metal removal rates much lower than those recorded in operating production ball mills. The corrosion component of ball metal loss in commercial mills represents less than 10% of the total loss expressed as micrometers/hour of exposure in recent USBM tests. Such small absolute losses are consistent with ball metal loss measured in production ball mill marked ball wear tests to determine effects of corrosion and abrasion resisting properties of alloys in operating mills which indicate that metal hardness and microstructure determine relative metal loss rates of a given situation. The combination of ore characteristics and grinding process dynamics determine metal loss severity. Alloying for corrosion resistance and modification of the milling corrosion environment yield relatively small metal loss reductions. Alloying and heat treatment to produce high hardness and microstructures of high carbon martensite and for cast irons, M7C3 carbides produces the lowest metal losses in typical wet grinding applications.

Jan 1, 1984

By Richard C. Neavel

Among the many compositional parameters used to judge the quality of a steam coal is the fouling factor of Attig and Duzy1 [% base in ash % acid in ash X % Na20] in ash. The higher the fouling factor, the more likely the heat transfer surfaces of the boiler will acquire a deleterious deposit of sintered ash. While examining the elemental composition of ash from various size and gravity fractions of coals from Illinois, we noticed that variations in the fouling factor were attributable mostly to variations in the sodium content. Further, sodium content was essentially the same in all sink-float fractions from a given coal. In other words, sodium was related neither to the ash nor to the organic material. We therefore concluded that the sodium was most likely in the pore water, which was approximately a constant proportion of all fractions. This led to the supposition that the sodium might be removable through water extraction. This supposition tended to confirm the observations of Daybell,2 Daybell and Gillham,3 and Gluskoter and Ruch4 that much of the sodium in coals existed as water soluble sodium ions. In passing, it should be noted that most sodium in Western U.S. coals (i.e., Wyoming, North Dakota, Montana) is not water soluble, but rather is fairly strongly held in association with the organic material (ion-exchanged).5 Because data reported in the literature were not very conclusive about the typical proportions of sodium that might be removed by water extraction, and because there were few data indicating extraction rates, and finally, because our calculations showed a favorable economic incentive to lower sodium contents, we initiated an experimental program to investigate water extraction of sodium from Illinois coals.

Jan 1, 1976

By Stephen Stone, Kerby Dobbs, G. Richard Whittecar, W. Lee Daniels, Zach Agioutantis, Tess Thompson

A common result of Environmental Impact Assessments associated with mining projects is the construction of new wetlands in areas disturbed by mining operations. Where appropriate, this mitigation may be considered an integral part of the mine reclamation process under the principles of sustainable development in the minerals industry. Wetbud is a new tool for estimating wetland water budgets using available weather data and site-specific topographic, soil and geohydrologic data, coupled with mass balance mathematics. Wetbud is primarily intended as a planning tool for use in the design of created wetlands, but it can also be applied to native wetlands or wetland restoration sites where the required input parameters can be specified. Wetbud can be run in its basic form where wetland topography, soil parameters and groundwater flux are simplified, or in the advanced form, where these parameters are included in a more complex approach via integration of the MODFLOW package, a free 3D program that was developed by the United States Geological Survey. Both versions can also include overbank flow hydrology sources and the advanced form can also model sloping and irregular topography. The program downloads weather data from the nearest applicable station and selects appropriate wet-normal-dry (W-N-D) years following a modest user data clean-up step. Wetbud also has the ability to utilize existing short-term (e.g. 6 to 9 months) groundwater data from an up-gradient well to simulate longer-term groundwater level inputs for the selected W-N-D years. In addition, Wetbud features a “Wizard” version that comes pre-loaded with 14 pre-selected weather data sets for all areas of Virginia that can develop a simple monthly water budget in less than 15 minutes – a feature that could be expanded anywhere geographically with historic weather data.

Jan 1, 2017

By Lennart Malmqvist

Decision-making in exploration deals with experience, knowledge, and sometimes faith, but very often financing and profit, mineral resource aspects, employment, and general political ambitions are parts of the scene. At one end of this spectrum, there is the prospector and his decision on the actual project. The exploration business now expands from its pioneering phase for the benefit of a single company to a wider spectrum which includes the benefit of the large mining consortium and a national development program. Its objectives are also to maintain employment and to favor long-term stability in a mining district or a mining company. The prospector then has new aspects and questions to consider such as, what to do in mining districts where there is a shortage of ore resources but there are still useful investments in mines, processing plants, etc. To analyze the exploration process, therefore, seems to be of great importance in a time of rapidly changing conditions. As in other areas of complex decision-making, for example, in the fields of investments, of production, and of the armed forces, computers most certainly have an important role to play in future exploration decision-making systems. However, we must first analyze our own business as closely as possible to find out what kind of information we need, i.e., why we recommend an exploration program as a good or a poor one. An important part of the debate about exploration is the case study. Case studies on exploration are few and most of those written are only about successful exploration programs. Where are the case studies of the failures and the not so successful programs? Every prospector knows that the majority of exploration projects fail. Consequently, the most important experience seems to be hidden in the failures.

Jan 1, 1979

Passive seismic monitoring is a useful tool for measuring wave propagation in rock mass in deep underground mining. About 20000 mining ? induced seismic events of a hard rock mine, are identified and investigated. The travel times of source-receiver pairs allow us to demonstrate temporal change in velocity. It was found that the average P wave velocity is about 6000 m/s in the mining regions. Velocity investigations on the data during about three months around the main shocks show a significant decrease of the average seismic wave velocity after the main shocks. The sudden drop of average velocity change after the main shocks implies the creation of new fractures in the rock mass due to the main shocks. Afterward, the average velocity increased to a normal level after a time duration of several days. A reasonable explanation for the post seismic velocity increase is that opened cracks begin to close due to crack healing.

Feb 23, 2014