Search Documents

By C. G. Anderson

Historically, the treatment of orebodies for recovery of valuable constituents presents many processing challenges. In a time of heightened environmental awareness, the constraints placed on processing complex orebodies are becoming more and more pronounced. As such, established technologies are limited in their ability to fill the needs of these emerging sources of raw materials. A prime example of this is in processing PGMs from primary sources. Normally, this type of material is found in a nickel-copper-iron sulfide matrix. Typically, these materials are processed by established pyrometallurgical means. However, other options should be considered. Hydrometallurgical processes are available which offer advantages over pyrometallurgical methods. One of these is the nitrogen species catalyzed sulfuric acid pressure leach used industrially by Sunshine Mining and Refining Company. In 1990, laboratory work was undertaken in cooperation with Stillwater Mining Company to test PGM matte materials from the Columbus, Montana smelter. The initial results were very positive, and they led to a design to recover PGMs in a high grade residue and to recover nickel and copper as valuable products. Handling the iron and other wastes in an environmentally safe manner was also successfully investigated.

Jan 1, 1995

By A. W. Wensel

The adsorption behavior of sodium oleate on brucite, Mg (OH)2, has been studied by Fourier transform infrared spectroscopy. Both internal reflection and diffuse reflection (DRIFT) methods were used to characterize the adsorbed oleate on brucite. DRIFT measurements were shown to be quantitative, and an equilibrium adsorption isotherm was obtained. The conformational behavior of the adsorbed oleate was investigated as a function of adsorption density. It was found that at sub-monolayer coverage the alkyl chains of the adsorbed oleate had more ?gauche? character than at multi-layer coverages. Also, DRIFT spectra revealed that the adsorbed species were magnesium dioleate. For internal reflection measurements single crystals of MgO were hydrolyzed to form a thin Mg (OH)2 layer.

Jan 1, 1994

By B. Basim

Novel chemicals that can be used for increasing the efficiency of fine coal dewatering were developed at Virginia Tech. Reagent A was tested on three different coal samples in laboratory vacuum filtration tests. These included flotation products from Middle Fork plant, Elkview Mining Company, and CONSOL, Inc. The tests conducted with the Middle Fork coal sample (100 mesh x 0) showed that cake moisture can be reduced by more than 10% beyond what can be achieved without using dewatering aid. This improvement was achieved at 1 lb/ton of Reagent A and 0.1 inch cake thickness. At 0.5 inches of cake thickness, the improvement was limited to 8% at the same reagent dosage. The results obtained with the Elkview coal (28 mesh x 0) showed similar advantages in using the novel dewatering aid. Depending on the reagent dosage, cake thickness, drying cycle time and temperature, it was possible to reduce the cake moisture to 12 to 14% range. In addition to achieving lower cake moisture, the use of Reagent A substantially decreased the cake formation time, indicating that the reagent improves the kinetics of dewatering. The test results obtained with CON SOL coal were not as good as with the other coals tested in the present work, which may be attributed to possible oxidation and/or contamination.

Jan 1, 1998

By J. S. Orphanos

The requirements for controlling air and stream pollution are a most timely subject for all concerned people. The coal industry has taken great measures to reduce both types of pollution. Through the use of more efficient scrubbing equipment on their thermal dryers, pollution has been considerably reduced. In many cases, the complete elimination of thermal drying by using centrifugal dryers to dewater fine coal products and meet customer specifications has completely eliminated air pollution from this source. To help eliminate stream pollution and the hazards created by tailing ponds, the coal industry is using centrifugal dewatering equipment. Use of centrifugals to dewater fine refuse for disposal would eliminate refuse ponds or extend their life. In doing this effectively and economically, preparation plants have the option of recycling the clarified water to close the water circuit or of discharging the water into receiving streams with the assurance that it contains an acceptable amount of refuse solids.

Jan 1, 1974

By H. Wesley Peirce

Although not generally recognized, Arizona has rock salt deposits unique in the United States. This uniqueness stems from a combination of two factors: (1) relatively youthful geologic age and (2) nonmarine origin. Although Arizona shares one deposit with Nevada (Figure 1, No. I) there are three others within the State (Nos. 2, 4, 5) that are believed to be both late Cenozoic in age (less than 15 million years) and nonmarine in origin. The only other recognized nonmarine salt deposits in the U.S. are much older, being in the early Cenozoic (Eocene) Green River Formation of Colorado and Wyoming. According to Johnson and Gonzales (1), the remaining rock salt deposits in the United States are marine and either Paleozoic or Mesozoic in age. Of the seven localities shown in Figure 1, six in the Basin and Range geologic province are believed to represent nomarine late Cenozoic phenomena and one (No. 7) in the Colorado Plateau geologic province is Paleozoic (Permian) in age and marine in origin. The following comments are intended to update the general geologic highlights of these deposits and to summarize the nature of their present utilization.

Jan 1, 1979

By D. Gatzemeier

The Jewett mine is a surface mine in central Texas, producing about 8,000,000 tons/year of lignite. The mine covers 46,000 acres of land. Approximately 430 people are employed by Northwestern Resources Company and through their efforts, the Jewett Mine is one of the most productive mining operations in the country. The Jewett Mine utilizes a unique structure of staff to convert Operations Research into plans which can be implemented at the "front line" level of the Operations Team. This planning not only makes the mine cost effective and efficient, but promotes creativity in mining, which promotes ongoing research to lower the cost of mining.

Jan 1, 1993

By D. Loy LeRoy

As we are all aware, the impacts of the 1977 Surface Mining Act and the implementing OSM Regulations require application of new, as well as existing, equipment and technologies. Our firm recently completed (June, 1979) a study for the Department of Energy titled "Analysis of the Impact of Public Law 95-87 on Mining Performance." The objective of the study was to analyze the impact of the Act and its regulations on mining performance in order to provide recommendations to alleviate the impacts identified, including identification of research needs. This paper presents some of the highlights of that report: projected cost increases; additional equipment needed for compliance; review of methods currently practiced or those which can be modified; and will focus particulary on equipment and technology applications.

Jan 1, 1980

By Gamal Rashed, Zorica Radakovic-Guzina, Khaled Mohamed

"Underground coal mines use mechanical bolts in addition to other types of bolts to control the rib deformation and to stabilize the yielded coal ribs. Limited research has been conducted to understand the performance of the mechanical bolts in coal ribs. Researchers from the National Institute for Occupational Safety and Health (NIOSH) conducted this work to understand the loading characteristics of mechanical bolts (stiffness and capacity) installed in coal ribs at five underground coal mines. Standard pull-out tests were performed in this study to define the loading characteristics of mechanical rib bolts. Different installation torques were applied to the tested bolts based on the strength of the coal seam. A typical tri-linear load-deformation response for mechanical bolts was obtained from these tests. It was found that the anchorage capacity depends mainly on the coal strength. Guidelines for modeling mechanical bolts have been developed using the tri-linear load-deformation response. The outcome of this research provides essential data for rib support design.INTRODUCTIONThe design of rib bolting in U.S. coal mines is based on a trial-and-error process, which is insufficient to eliminate injuries and fatalities caused by rib falls. In the last 10 years, rib failures have resulted in 17 fatalities, representing 52% of the ground-fall fatalities in underground coal mines in the United States (MSHA, 2018). Recently, NIOSH researchers surveyed 90 sites in 14 underground coal mines in the Eastern United States and found that 11 mines are bolting coal ribs, with 4 of those mines using the conventional mechanical bolts and the others using fully-grouted bolts. NIOSH researchers are developing an engineering design procedure for rib support. Pull-out test programs for mechanical and grouted rib bolts were conducted to understand the rib control mechanisms of rib bolts. Only the test results of mechanical bolts are presented in this paper.Mechanical bolt (or point-anchored bolt) is a tensioned bolt anchored down the borehole with a mechanical expansion shell or a resin-grouted medium (Peng and Tang, 1984). The mechanical anchor bolt consists of a plug, a shell anchor, a headed bar with the top end threaded, a bearing plate, a hardened washer, and occasionally a friction-reducing washer. The shell anchor can be either standard or bail type (Figure 1). The standard type shell is held in place by a nut, while the bail anchor uses a strap to hold the shell in place (Peng, 2008). The diameter of the bar is generally 16 mm (? in) for the #5 bolt or 19 mm (6/8 in) for the #6 bolt. The diameter of the hole that the bolt is inserted into must be carefully controlled, since an oversized hole can result in poor anchorage (Moss, 1971). The anchorage is obtained by applying torque to the bolt head, which in turn pulls the plug down in the shell and expands the serrated leaves against the sides of the hole-wall. In the resin-grouted anchor, the resin replaces the mechanical expansion shell at the end of the hole. The anchorage is achieved by bonding between the resin, bolt, and the hole-wall."

Jan 1, 2019

By J. A. Lombardi

Innovative hard rock narrow-vein, longwall, and stope leach mining systems concepts are described and evaluated economically. The principal tool proposed for use in these systems for both mine development and production is the U.S. Bureau of Mines radial-axial splitter. The mining systems concepts are prefeasibility level costed and projected to be cost competitive for steeply dipping veins, 0.6-1.2 m wide, for horizontal tabular ores 2 m -5 m thick, and for leachable ores with greater than a 1.7:1 stripping ratio. In all of the systems the orebody, less swell, is retained underground for use as backfill.

Jan 1, 1994

By J. A. Porter

This paper uses project examples, primarily associated with large iron ore mines in Brazil, to demonstrate opportunities for the mining industry to go beyond traditional compliance and impact mitigation to proactively operate within the ethics of environmental and economic sustainability.

Jan 1, 1994

Microwave pretreatment can improve grindability by weakening brittle particulate material prior to size reduction. The differential thermal expansion experienced by multiphase materials during rapid heating can also promote damage in the grain-boundary region, which may ultimately translate into enhanced liberation. The effect of microwave pretreatment on the breakage characteristics of different ores has been studied using the Ultrafast Load Cell. The energy accumulated during impact (fracture energy) and the particle stiffness have been measured for untreated and microwaved ore samples. It has been observed that microwave pretreatment can weaken brittle multiphase particulate material, as observed by reductions in fracture energy and increase in damage.

Jan 1, 1996

By L. George Imperato

The Blocked Iron Corporation has been active for many years in the development of mineral agglomeration processes by cold chemical induration. Millions of tons of iron ore fines agglomerated by their methods have been consumed in open hearth steel making furnaces. Some of you may remember these open hearth agglomerates as the carbonate-bonded cylindrical block shown in figure 1. With the realization that iron making would create the greatest demand for agglomerates our research efforts were directed to the production of carbonate- bonded (C-B) pellets containing iron ore, flux and carbon, shown in figure 2.

Jan 1, 1968

By W. E. L. Minter

Discussion by R.W. Hutchinson Minter's excellent recent paper (1990) on the great paleoplacer gold deposits of the Witwatersrand and its subsequent discussion (Cheney, 1991) and reply (Minter, 1991) provide an informative, interesting and up-to-date review of the geology of these unique ores and some long enigmatic questions regarding their origin. Clearly summarized by Minter (1990) are the compelling sedimentologic and stratigraphic relationships indicating that the Central Rand Group conglomerates are ancient placers and documenting the fluvio-deltaic conditions of their transport and deposition. As Minter (1991) indicates, Cheney's discussion broadens Minter's 1990 coverage of the subject by considering higher and lower stratigraphic units and by adding detailed comments concerning recently published information about metamorphic and age relationships. Cheney's discussion and Minter's reply also readdress the old controversy of epigenetic hydrothermal vs. syndepositional placer origin for these deposits. This controversy has been resurrected by: • recent recognition of hydrothermally-altered granites (HAGS) in the older Archean basement rocks that lie unconformably beneath the Dominion Group rocks north and west of the Witwatersrand depository; • recognition of greenschist metamorphic assemblages in the Witwatersrand strata; and • the presence of interpreted epigenetic mineral assemblages and textures in some of the deposits. These relationships are briefly discussed by Cheney who suggests they may result from later, superimposed metamorphism and deformation and do not prove that the gold was introduced by epigenetic/metamorphogenic processes. In his paper, Minter (1990) cited the 1986 abstract of a subsequently published paper by Hutchinson and Viljoen (1988) who also considered many of these aspects and attempted to integrate them all in abroad genetic hypothesis. In addition, they emphasized the additional important problem of determining the source for the Witwatersrand gold. Although this issue was partially addressed by Reimer (1984), Mossman and Dyer (1985) and Reimer and Mossman (1990), the question has been generally under emphasized in earlier work and was, therefore, not stressed by Minter and Cheney. Reimer (1985) also emphasized the importance of weathering of the basin's Archean hinterland and its affects on Witwatersrand sedimentation. Since the epigenetic hydrothermal hypothesis was essentially discarded in favor of placerist origin, the gold source for these great deposits has generally been attributed to the weathering of lodes in greenstones or granites of the uplifted, older Archean hinterland to the north and west. However, Hutchinson & Viljoen (1988) present evidence that this explanation is inadequate, as well as data in support of an alternative explanation. They suggest that the gold and accompanying abundant, clearly detrital and auriferous pyrite in the conglomerate reefs were derived by erosional degradation of auriferous-pyritic exhalite previously deposited, by shallow marine discharge of hydrothermal fluids, along the fault-bound northwestern margins of the Witwatersrand depository. The auriferous-pyritic exhalites were generated by fluid-rock reactions in the subsurface, particularly in the highly-altered lavas of the Dominion Group but also in adjacent basement granitic rocks. The process envisaged is comparable to that observed in sea floor hydrothermal systems today, although, in this case, it occurred at the margin of a rapidly subsiding, shallow marine or continental basin. Important evidence for this explanation is the anomalous gold content of the ferruginous, shaley strata occurring throughout the Witwatersrand Supergroup and including the distinctive contorted bed that is an iron formation. These layers have been interpreted (Hutchinson and Viljoen, 1988 and 1990) to represent the more distal, finer-grained, mixed chemical/clastic sedimentary strata. Thus, they are the basinal equivalents of the proximal, auriferous-pyritic exhalites that were deposited along the basin's margin and subsequently reworked by sedimentary processes. This gold source explanation resolves many of the enigmatic questions regarding Witwatersrand geology and the reawakened controversy between proponents of hydrothermal and placerist genetic hypotheses. The theory invokes a hydrothermal origin for the gold in the basin-margin pyritic exhalites, thus explaining the visible hydrothermal characteristics (Figs. 1 and 2). It also provides compelling evidence for placer origin by encompassing all of the fluvio-deltaic processes of clastic sedimentary transport and deposition that are clearly summarized by Minter. These characteristics result from the degradational reworking of the pyritic exhalites along the depository's margins. Fluvial reworking, transport and deltaic redeposition of this detritus, along with additional detritus carried into the depository from the hinterland, then formed the conglomerate reefs. Other enigmatic aspects of Witwatersrand geology include: • the rarity of magnetite and ilmenite (the two most common heavy minerals in placer deposits) and the contrary abundance of leucoxene in the conglomerate reefs; • the presence of differing varieties of pyrite (authigenic, allogenic, compact and porous) all of which are auriferous; and • the presence of well-rounded pebbles, even cobbles, of pyrite that, in view of the brittleness of the mineral, could not have been transported great distances from a hinterland.

Jan 1, 1993

By M. C. Fuerstenau

Flotation data indicate that sulfonate and dodecylamine adsorb physically on Mn02 at ambient temperature. Oleate also adsorbs physically if the zero-point-of-charge of the Mn02 is sufficiently high. Chemisorption of oleate apparently occurs between pH 8 and 9, and this phenomenon is enhanced considerably at elevated temperature.

Jan 1, 1966

By Kevin Sierra, Orfelinda Avalo, Julio Guizado, Edwilde Yoplac, David Martinez

Mining tailings are slurry byproducts of mineral recovery. They generate serious environmental risks due to their toxicity when exposed to water and oxygen. Studies focus on eco-friendly alternatives for mitigating these environmental impacts. Processing these tailings enables a sustainable mineral production model through circular economy practices. This study evaluates using gold mining tailings to recover gold and produce bricks. Flotation tests obtained a concentrate with 86.66% gold recovery, containing sulfides (pyrite, arsenopyrite) and a tailing with silicates and oxides suitable for brick manufacturing and ornamental pieces. This approach promotes eco-friendly solutions and a greener approach to mining operations.

Feb 1, 2024

By E. J. Sullivan

This study seeks to define the mechanism of oxyanion sorption onto surfactant-modified zeolites. Zeolites which have been treated with hexadecyltrimethylammonium bromide (HDTMA) surfactant to produce a hydrophobic surface are capable of sorbing both organic compounds as well as oxyanions such as chromate, selenate, and sulfate. Simple ion exchange and charge-balancing mechanisms do not fully explain this unusual phenomenon. The sorption of HDTMA surfactant appears to be partly ion exchange and partly sorption to non-ion-exchangeable sites. Sorption of chromate is a simple exchange mechanism with bromide, which co-adsorbs with HDTMA to form a surface precipitate. Information from this study will be used to design on-site and in situ treatment systems for contaminated water, such as filter beds and permeable barriers.

Jan 1, 1995

By A. E. Petersen

The United States Bureau of Mines conducted research on high-intensity magnetic separation methods for upgrading tantalum concentrates from Alabama. Process flow sheets were studied to maximize tin removal and minimize tantalum loss. Using laboratory-scale equipment, concentrates were produced which contained over 65% combined Ta2O5-Nb2O5. Up to 78% of the tin was recovered as a byproduct, containing about 70% SnO2. Only 1 to 5% of the tantalum reported with the tin byproduct. The producer subsequently incorporated high-intensity magnetic separation into its process flow sheet to provide concentrates for the National Defense Stockpile.

Jan 1, 1993

By K. J. Stanaway

Environmental pressures on waste disposal are forcing pigment producers to use higher content TiO2 feedstocks with lower levels of trace elements. Despite this, 50% of the worlds TiO2 comes from ilmenite concentrates with only 37 -54 % TiO2 An industry growth rate of 25 % in the next ten years combined with trends to diminishing resources and lower grades for rutile (95 % TiO2) and leucoxenized ilmenite (55 to 90% TiO2) mean that unless new discoveries are made soon, the industry will become even more reliant on ilmenite. A hypothetical ideal feedstock is presented and strategies to obtain it are suggested. Reasons for some of the mineral specifications are given.

Jan 1, 1994

By M. Beale

Fuzzy logic and neural networks are new technologies being applied in many areas of engineering and business. While it is not always clear which kinds of problems are best suited to these technologies, and which problems are best approached with more standard methodologies, both fuzzy logic and neural networks appear to show great promise in the field of control systems. This paper demonstrates two advantages that these technologies offer: Easy controller design in the absence of a mathematical model of the plant to be controlled, and adaptive control capable of quickly responding to changes in the plant.

Jan 1, 1994

Selective Flocculation process development generally involves single mineral flocculation tests to identify the appropriate polymer and experimental conditions for achieving the desired selectivity. Invariably the selectivity predicted on the basis of such tests is not realized when mixed mineral tests are conducted. A systematic experimental investigation revealed that adsorption of the polymer on various substrates is critical to selecting the suitable flocculent. Simultaneously, a mathematical model was developed to predict the overall process efficiency with a given polymer. In this paper, results of these efforts to scientifically design a suitable selective flocculation process are presented.

Jan 1, 1991