Search Documents

By C. S. Compton, D. R. Dolinar, D. C. Oyler

More than 80% of U.S. roof bolts are fully-grouted, but about 1500 roof falls are reported each year. Anchorage failure of a fully grouted bolt can occur when the roof is active near the top of the hole. This paper reports on an extensive series of short-encapsulation pull tests (in which the bolts are installed with only 1 ft of resin) that were conducted in the National Institute for Occupational Safety and Health(NIOSH) Mine Safety Research Laboratory and operating mines in WV and PA. The tests confirmed that poor anchorage can been countered under some weak rock conditions. Suggestions for improving anchorage are included.

Jan 1, 2003

By E. Peuraniemi, S. Strömberg, S. Jyrkönen, A. Jokilaakso

Several sulfidic raw materials have been flash oxidized in a laboratory furnace in oxidizing atmospheres at temperatures of 500-1100°C. Chemical analysis was used to determine the oxidation degree, and optical and scanning electron microscopy combined with energy dispersive analysis were used for characterization of the reacted particles. The studied materials included both Cu and Ni concentrates and mattes. In fixed conditions, the temperature dependence of sulphur removal rate was found to be equal for all the copper concentrates studied. Nickel concentrates and Cu- and Ni-mattes were, however, found to be less reactive. Most of the particles were found to spheroidize and to fragment to small droplets under intensively oxidizing conditions. The product particles were frequently found to be iron oxide cenospheres or dense spheres with a composition of mixed Cu-(Ni-)Fe oxides.

Jan 1, 1998

By T. Winkler, J. Tokarczyk, D. Michalak, W. Chuchnowski, M. Dudek

Engineering Methods aiding Sustainable Development of Mining Systems will be presented, and especially: virtual prototyping for designing of Mining Systems with Health Protection and Safety criteria taken into consideration, modelling and assessment of technical and health hazards that can occur during operation of Mining Systems, creation of knowledge repositories that disseminate safe work methods with consideration of existing language and culture barriers, dissemination of the methods integrating world community and Mining Systems users.

Jan 1, 2011

By Jeffrey Anderson, Cindi Byrns, Andy Davis

A closure plan was developed for the Intera Pond Facility, a former acid leaching collection pond at the BHP Robinson Mining Operations. To properly close the Intera Pond Facility, an engineering plan that was both technical and cost effective was developed. A primary objective of this closure project was to demonstrate to State regulators that following the proposed plan would minimize further degradation of water resources. Field data demonstrated natural attenuation of metal enriched solutes via carbonate reactions. Prospective fate and transport modeling indicated that it would not continue to degrade waters of the State.

Jan 1, 2000

By J. F. T. Agapito

Energy West Mining operates the Deer Creek and Cottonwood/Trail Mountain coal mines in the Wasatch Plateau about 40 km (25 miles) southwest of Price, UT. The Deer Creek Mine extracts the Upper Blind Canyon seam and the Cottonwood/Trail Mountain Mine extracts the Hiawatha seam 12 to 36 m (40 to 120 ft) below. Both seams average about 2.8 m (9 ft) in thickness. Cover depths exceed 550 m (1,800 ft) in a large portion of the unmined reserve. Stability problems at Deer Creek are mostly due to coal bursts caused by high stresses associated with deep cover and sandstone channels. Most of the bursts have occurred in gate pillars and, to a lesser extent, at the longwall face and during development. The introduction of a two-entry gateroad system with 9-m- (30-ft-) wide yield pillars has been a major factor in controlling and minimizing gate pillar [ ] bursts (Agapito et al., 1988). However, some bursting began to occur in the 9-m- (30-ft-) wide pillars as cover depths reached 550 to 610 m (1,800 to 2,000 ft). This was due to more rapid and higher abutment loading in areas with very strong roof and stiff floor.

Jan 1, 1997

By R. A. Halatchev

Historically two basic approaches of production sequencing have been formed in the theory of open pit mine design. The first approach implements a technological discretization of the pit space within the ultimate pit outlines where the minimum working width is the limiting technological factor. The second approach uses a pseudo-economic discretization based on the implementation of analytical methods for designing intermediate/ultimate pit outlines and the concept of pit shells generation. The paper offers an elaborate analysis of both approaches used currently for discretization of the geological medium into working benches and modelling the working zone of open pit mine. The analysis is extended with a new vision for unification of the mining systems in open pit mine design under the form of a classification. A comparison of the approaches is provided to illustrate their advantages and disadvantages with regard to the implementation of the principle of waste deferment as one of the main principles of mine planning that exploits the time effect of money.

Jan 1, 2003

By W. E. Foreman, A. Hayatdavoudi, A. Ghalambor

The objective of this investigation was to determine the sensitivity of three selected input parameters in the operational control of continuous bottom fed thickeners used for the treatment of coal refuse slurries. The three variable parameters were "Feed Flow Rate," "Feed pH," and "Feed Solids Concentration." These three input parameters were studied under three cationic-anionic polymeric conditions. For each polymeric condition, two mathematical models were developed, one for overflow response and the other for underflow response. The combination polymers produced the best quality of overflow and underflow. For this polymeric condition, change in the feed solids concentration was the most sensitive factor in the maintenance of the overflow quality, and the feed pH was the most sensitive factor for the maintenance of underflow quality. The mathematical models generated a set of plots that would allow an operator to control and/or adjust any of the three variables to achieve optimum conditions.

Jan 1, 1991

By N. Zouridakis

Radon is an established lung carcinogen and remains the most important environmental radiation exposure. It was estimated that inhalation of radon and its short-lived decay products accounts on average for about one half of the effective dose equivalent from all natural sources of radiation. Radon contained in household water can transferred into room air as a result of agitation or heating. An indoor air concentration of 400 Bq/m3 is obtained if the radon concentration in household water is 4 kBq/L. A typical concentration of radon in ground water is about 1000 times lower than this concentration but sometime elevated concentrations of some kBq/L in ground water are reported. In this work a Liquid Scintillation counting system is used to obtain fast and accurate measurements of radon (222Rn) in water samples from Argolida, Greece.

Jan 1, 2007

By William P. Lorenz

The paper describes a uranium by-product recovery plant operating within a copper leach, solvent extraction, and electrowinning circuit. The operation is unique because it is integrated into the main process stream of the copper circuit The plant processes 1408 m3/h of copper solutions containing about 10 mg/L of uranium. An Eluex type process was selected due to its compatibility with the copper leach plant. The paper includes an overview of the copper circuit

Jan 1, 1983

By P. Stanley Jacobsen, Hemant B. Gala, Richard E. Hucko

Coal is the nation's most abundant fossil energy resource. However, its use is limited because of the nature and amount of associated impurities, such as mineral matter, sulfur, trace elements, and moisture. The moderate-to high- sulfur content of many U.S. coals is of particular concern as current and newer, potentially more stringent, regulations require reduction in sulfur oxide emissions. Release of particulates, NOx, and other pollutants during the coal-use cycle is also of concern. The current practice of controlling sulfur oxide emissions in the major steps of the coal- use cycle is limited mainly to coal preparation by physical beneficiation and, to a smaller extent, to post-utilization cleanup (flue gas desulfurization). Approximately two-thirds of the coal from states east of the Mississippi river is physically cleaned, whereas only 15% to 20% of the operating boilers in the utility industry are equipped with scrubbers to desulfurize the flue gas (Henzel, 1988). Physical beneficiation methods can be very effective in removing mineral matter, including pyritic sulfur, from coal. These processes take advantage of the differences in physical proper- ties between coal and mineral matter to achieve the separation. In a typical physical cleaning operation, raw coal is crushed to about a 50-mm (2-inch) top size. It is then screened into coarse, intermediate, and fine sizes. Crushing the coal liberates some of the ash-forming minerals, including a portion of the sulfur that is not chemically bound to the coal. The per- centage of impurities freed from the coal matrix generally increases as the coal particle size decreases. The coarse- and intermediate-sized coals are typically subjected to a cleaning pro- cess based on differences in specific gravity between coal particles and the associated impurities. Such cleaning processes used include jigs, dense-medium baths, cyclone systems, and concentrating tables. The fine-sized (typically less than 0.5-mm) coal, if beneficiated, is typically cleaned using a froth flotation technique based on the differences in surface proper- ties between coal and its associated impurities. At fine sizes, greater cleaning potential exists because a greater portion of the impurities is released from the coal matrix. However, this potential is not fully realized owing to inefficiencies in separating fine particles using state- of-the-art flotation technology. Overall, current commercial coal preparation processes are estimated to remove up to 60% of the ash and 10% to 30% of the sulfur, depending on the coal characteristics, with product weight recoveries rang- ing from about 60% to 90% and thermal recoveries of about 85% to 98% (Versar, 1985; Science Applications International Corporation, 1987; Hoffman- Muntner Corporation, 1978). For many U.S. coals, grinding to sizes finer than those used in current coal preparation plants is required to liberate most of the physically bound impurities from the coal matrix. As noted, conventional coal-cleaning methods are not very effective at these fine sizes. Accordingly, the expanded use of domestic coal requires the development of advanced coal cleaning technologies that can provide economic performance while reducing environmental impacts. Program Goals and Objectives The overall goal of the U.S. Department of Energy (D0E)'s Coal Preparation Program is to provide the scientific and engineering knowledge base that industry can utilize to produce economically competitive and environmentally acceptable clean-coal products for introduction as market conditions warrant. The coal preparation process(es) should remove undesirable components from coal and improve its handling characteristics, thus making the product coal technically, as well as economically, viable as a competitor with petroleum-derived fuels and natural gas, and with alternative environmental control technologies. The coal preparation process must be applicable to a wide variety of bituminous and low-rank coals. The cleaning process should reduce the variability among clean-coal products from various raw coals, thus significantly increasing the range of potential end uses for each raw coal. To the extent that deeply cleaned coal products have greatly reduced levels of

Jan 1, 1988

By J. Fuller, L. Marsden

Windborne dust from alkaline salt flats and mining-related tailings ponds is especially prone to threaten applicable ambient air quality standards. Sodium carbonate crystals, typically present, weather to an exceedingly fine, non-cohesive dust, causing air quality problems for miles downwind. Recently developed specialized polymers react with alkaline dust to form sturdy, wind-resistant crusts with good longevity. An on-going demonstration project at a major trona facility has developed techniques for cost-effective application of these polymers over large areas of soft tailings or sediments in a wide variety of situations. Recently treated areas on the order of 80 acres show effective suppression of dust.

Jan 1, 2004

By J de Cuyper, V. M. Lovell, W. Freyberger

The recovery of apatite from the phoscorite ores occurring in the Transvaal, Republic of South Africa, involves a flotation process that is particularly difficult to characterize from a fundamental point of view. However, the reagents used, (tall oil fatty acid, nonylphenyltetraglycol ether, sodium silicate, and sodium hydroxide) can successfully bring about a separation of apatite from dolomitic calcite, which is the most troublesome gangue component. Recently, it has been demonstrated with some flotation feeds that the addition of certain polysaccharides can improve the flotation significantly. It has been shown that the metallurgy obtained is closely linked to the nature of the froth, and this, in turn, is influenced, often dramatically, by the presence or absence of certain of the reagents. The character of the froth depends less on the inherent frothing ability of these reagents than on the presence or absence of fine mineral particles in the froth, and on their surface characteristics and state of aggregation. The polyglycol ether and the polysacchar- ides have been shown to affect these properties, and it is suggested that a major function of these reagents is to modulate the properties of the fine particles in the pulp, thereby changing the character of the froth and giving rise to improved results.

Jan 1, 1976

By Robert Marks, Enrico Dal Negro, Richard Schulkins

"In July 2012 construction started on the Grosvenor project, a five million tonne per annum underground longwall mine planned for Moranbah in Central Queensland. Grosvenor is located immediately to the south of the existing Moranbah North mine which has been in operation since 1998. EPBM technology is being used for the first time in Australia for excavation of a coal drift. The TBM was used to build two drifts on the project, one for the coal conveyor which will transport to surface, and another for people and equipment to access the underground once the mine’s operational (as shown in figure 1). The TBM will pass beneath a steel archway roof that has been installed at the drift’s entrance and begin drilling into the ground to build the seven metre diameter tunnel, descending at an angle of one in eight until it reaches the depth of the coal seam approximately 160 metres below.INTRODUCTION AND BACKGROUND The first TBM used in a coal mine was in 1962, a Wohlmyer, in Westerholt, Germany. A further 75 km of tunnels were excavated in coalmines within Germany between 1971 to 1983. This paper will review the Grosvenor Mine project (Grosvenor) owned by Anglo American Metallurgical Coal (Met Coal) includes the construction of a new underground coal mine and surface facilities on the northern boundary of the town of Moranbah in the Central Queensland Bowen Basin coal precinct. The contract to undertake the underground development works was awarded to Redpath in 2012. The scope of the Grosvenor Project was to construct temporary office and workshop facilities, install 2 portal arches, backfill boxcuts and infrastructure, excavate by EPBM method 967 m of 1:6 gradient Conveyor Drift and 1,258 m of 1:8 gradient Transport Drift, development of 2,520 m of pit bottom area roadways and development of 10,550 m of the first longwall tailgate. In the following figures 2 and 3, is possible to see the aerial view of the job-site."

Jan 1, 2016

By M. Wasel

The Gross Rosebel gold deposits are located in theGuiana Shield of northcentral Suriname in South America. The property lies 80 km (50 miles) south of the capital city of Paramaribo. Gross Rosebel covers 170 km2 (65 sq miles) in an area of small hills covered primarily with secondary tropical rain forest, separated by discontinuous savannah (Fig. 1). The concession is accessible from Paramaribo by a 120-km (75-mile) paved and all-weather gravel road. Surficial gold was discovered in 1880 by local artisanal miners. This was followed by small-scale mechanized mining from 1885 to 1939. Placer Development carried out the first systematic exploration program from 1974 to 1977. In May 1992, Golden Star Resources optioned the property. Initial shallow reconnaissance diamond drilling of the extensive surface geochemical anomalies intersected sporadic gold mineralization with no apparent continuity between drill sections. Successive deep augering, trenching and systematic grid drilling, based on information from surface mapping, allowed the development of a preliminary geological model. Further drilling of specific structural-lithologic targets and more complete synthesis of geological data from the trenching and deep auger sampling added to the geological model and defined the multiple controls of gold mineralization. Carefully planned infill drilling on a tighter grid spacing resulted in progressive definition of reserves within six discrete gold deposits. Reserves based on $11.25/g ($350/oz) gold now stand at 35.5 Mt (39.1 million st) of 1.8 g/t (0.053 oz/st) gold, or 62.2 t (2 million oz) of gold.

Jan 1, 1998

By Rowan Melrose, Naj. I. Aziz, Arvind Misra

Mathematical models have been developed to simulate longwall heading development systems in Australian Longwall Mines. The models developed consider the effect of non concurrent cutting and supporting systems and concurrent cutting and supporting systems. They also consider the impact of operating parameters on each of these systems. Operating parameters that are considered include pillar dimensions, the use of surge cars, bolting time, shuttle car speed and heading advance per cycle. The effect of these parameters is considered with respect to production rates and also panel advance rates.

Jan 1, 1996

By C. P. Shen, H. C. Tsai, Bennie Chu, Y. S. Hsieh

The Pinglin tunnels are situated within the fold-and-thrust belt structural region in Taiwan, due to continent-arc collision and plate tectonic setting. The pilot tunnel TBM (§=4.8m) became stuck ten times with the standstills to date. The westbound main tunnel TBM (§=11.74m) was buried in a collapsing calamity. The main tunnel TBM shall identify and overcome the adverse geology with high volume of ground water ingress itself. This paper presents our experience and methodology through the adverse geology with Pinglin large TBM.

Jan 1, 1999

By M. Hardy, K. Nielsen, M. Ramey

American Soda, LLP has commissioned the first solution mine for recovery of naturally formed sodium bicarbonate (nahcolite) from low-grade deposits using high-pressure, high-temperature injection fluid. This project, known as the Yankee Gulch Project, was commissioned33 years after discovery of the deposit and followed an intensive four-year feasibility study that included a full-scale pilot test. The nahcoliteis co-mingled with oil shale and is impermeable. Solution mining is achieved by a combination of thermo-mechanical cracking and dissolution. Elevated temperatures are required to initiate the thermally induced cracking and to enhance solubility of the nahcolite, which is highly temperature dependent. This paper will provide an overview of the development of the project from discovery, characterization, pilot testing, permitting and commissioning, with emphasis on the solution mining aspects.

Jan 1, 2003

By P. Johnson, G. E. Jones, G. K. Hoffman, C. B. Krueger, J. S. Raugust, M. Wilks, V. T. McLemore

The NMBGMR is slowly converting historical data into a relational database using Microsoft Access 97. The purpose of this database is to provide data on districts, mines, and mills in New Mexico to government agencies, public organizations, industry, and citizens to make informed decisions about resource development, resource management, water supplies, environmental impacts, hazard assessment, and waste disposal. Once the data are entered into the database with locations, the data can easily be converted to GIS format for displaying as different map layers.

Jan 1, 2003

By Nikhil Dhawan, Veeranjaneyulu Rayapudi, Singh Rahulkumar Sunil

The ever-increasing demand for steel and the subsequent depletion of high-grade ores requires the massive utilization of low-grade iron ores. In the present study, an iron ore slime sample containing 56.1% Fe was investigated using physical beneficiation, carbothermal reduction, and a microwave-assisted process; however, physical beneficiation and microwave exposure were found to be inefficient as they yielded lower iron recovery. Using coconut shell as an alternative reductant was found to be promising and does not lead to the formation of higher iron oxides, such as fayalite and wustite phases. The microwave-assisted carbothermal reduction was found at par with conventional reduction, saving time and heating. The optimum magnetic concentrate obtained in both carbothermal reduction routes (microwave and muffle furnace: Fe grade, Fe recovery, and yield of 64.3, 97, and 84%, and 67, 99, and 83%, respectively) are suitable for alternative iron-making or blast furnace units.

By Gennaro G. Ph. D Marino

In order to improve handling of subsidence damages the Illinois Mine Subsidence Insurance Fund supported the development of novel cost-effective methods of repair. The research in developing the repairs was directed towards the most common and costly damages that had been observed. As a result repair techniques were designed for structurally cracked foundations in the tension zone; structurally cracked foundations in the compression zone; and damaged or undamaged tilted foundations. When appropriate, the postulated methods would result in: 1. significant cost savings (over conventional procedures); 2. a structural capacity greater than when the foundation was untracked; and 3. an aesthetic appeal. All the postulated repair methodologies were laboratory and/or field tested. The paper will summarize the essentials of each technique developed and the test results.

Jan 1, 1986