Search Documents

By Brendan Demich, MAHIYAR F. NASARWANJI, Alan G. Mayton

Nonfatal injuries from slips, trips, and falls (STF) that occur at surface mines can result from inadequate lighting. Mobile equipment operators are among the occupations associated with the nonfatal incidents reported to the U.S. Mine Safety and Health Administration (MSHA). In addition, getting on/off the equipment (ingress/egress) frequently adds to the highest proportion of nonfatal incidents. Accordingly, researchers at the Pittsburgh Mining Research Division (PMRD), National Institute for Occupational Safety and Health (NIOSH) conducted a field study to investigate lighting on haul trucks and wheel loaderswith regard to glare and illuminance levels recommended by the Illuminating Engineering Society (IES). The objective was to determine whether two light-emitting diode (LED) area luminaires—a Mr. Beams® (model MB390 Ultrabright) (area luminaire-1) and a NIOSH-developed Saturn (custom-designed for a mine roof bolter study) (area luminaire-2)—could complement a headlamp luminaire. Measured levels of visual tasks, with the headlamp alone and the area luminaires plus the headlamp, demonstrated that illuminance met or exceeded IES-recommended levels. Nevertheless, the area luminaires illuminated a much broader area, which is key to increasing hazard awareness. Discomfort and disability glare were lower with area luminaire-1 than with area luminaire-2. Differences in glare were more noticeable for newer models of haul trucks and loaders featuring updated ingress/egress system designs. This study demonstrates that commercially available luminaires, such as area luminaire-1, are capable of complementing headlamp lighting, and can thus improve a miner’s ability to detect and avoid STF hazards.

Jun 17, 2020

By Ying Lu, Jeffrey C. Johnson, Chen-Luh Lin, Jan D. Miller, Sindhoora Puvvada

The amount of energy used to break rock is of interest in mine-to-mill operations to minimize energy consumption during blasting at the mine site and comminution at the processing plant. In this research, a direct energy measurement was made using high-velocity impact to cause breakage of long granite cores, and to study the energy dissipation along the entire bar length. The results show the formation of three zones of damage — fragmentation, fracture and elastic — that have been characterized in 3D using X-ray tomography. The fragmentation zone of the granite bars was studied in detail to describe the particle size distribution and the particle shape characteristics. The experimental energy dissipation in the fragmentation zone was found to be in close agreement with the expected energy calculated from the Bond work index (BWI) equation [1] when the anisotropic granite particles in the fragmentation zone are defined by length rather than by sieve size. The results increase our understanding of rock breakage and energy consumption and may find future applications in mine-to-mill operations.

By Anthony Iannacchione, Tim Miller, Nicole Evanek

The Subtropolis Mine is a room-and-pillar mine extracting the Vanport Limestone near Petersburg, OH. In February 2018, mine management began implementing a new mine layout to better control the negative effects of excessive levels of horizontal stress. Almost immediately, the conditions in the headings improved. Conversely, and as expected, stress-related damage was concentrated within crosscuts. Over the last 18 months, the mine operator has diligently experimented with different techniques/methods to lessen the impact of the instabilities in the outby crosscuts. The range of controls used by the mine operator include angled crosscuts, crosscut offsets, increased distance between crosscuts, arched crosscuts, cable-bolted crosscuts, altered blasting pattern, and windows. A window is used to resist roof deformation by leaving a strong brow of roof rock within the crosscuts.

By ERIK CHARRIER, HUGH MILLER, JOSEF BOURGEOIS

In this study, a unique excavation system was characterized using waterjet technology as the primary tool for material removal during rehabilitation of reinforced concrete and shotcrete structural liners. Through empirical testing, this research seeks to validate the hypothesis that waterjet removal of these support systems will result in less unintended damage than conventional removal methods. The intent is to develop a viable technology that will reduce the collateral damage caused to surrounding liners during excavation, improve the adhesion between shotcrete and the substrate for longer lasting ground support, and improve overall safety for workers in underground environments. An analysis on the fracture mechanisms and operating parameters of each method was completed. Instrumented shotcrete panels were physically tested and examined through visual inspection and ground penetrating radar (GPR) to compare substrate damage according to each testing method. After testing was completed, the data strongly indicate that waterjet cutting causes less collateral damage to the surrounding intact liner and substrate than conventional impact hammers. This research is intended to provide a scientific basis for additional applied research in the rapid excavation and repair of shotcrete support systems.

By T. P. Meloy

Current coal cleaning technology uses heavy media (HM) for the recovery of coal in particles larger than 1/16 of an inch. Through the use of float sink measurements of the feed and products to commercial HM unit operations, a selection function, sometimes called Tromp curve in the coal industry, can be computed. Since the selection function is a plot f the probability of a particle appearing in the float versus the particle density, the slope of the curve will be sharper at the point where the particle has a 50% chance f appearing in the float. Thus, the separation will be better. Fine-tuning a unit operation or a circuit of unit operations requires that the selection function be accurately known. By current practice, it is difficult to obtain an accurate measure of the slope because, when the selection function is plotted versus density, the data forms an S-shaped curve which lacks data points near the 505 point of the curve. This lack of sensitivity in measuring the slope means that small recovery improvements cannot be detected; thus, only large improvements are measurable. Since most engineering improvements are small when individually considered, but large when aggregated ever many small improvements, this lack of measurement sensitivity rules out the slew march toward improved efficiency. This paper presents a method of analyzing heavy media selection functions resulting in a far more effective measure of the selective function slope. Furthermore, this improved method is applied to a number of industrial coal cleaning plants for both heavy media and heavy media cyclones. Using the work of Hudy (1968), and Deurbrouck and Hudy (1972), selection functions for individual unit operations in each plant are calculated as a function f particle size as well as density.

Jan 1, 1982

By Isabel F. Barton, Matthew J. Gabriel, CARSON ROBERTS, JOHN LYONS-BARAL, LEON DUPLESSIS, Mark D. Barton

Geometallurgical characterization is increasingly used in the mining industry to model ore types, predict process performance and identify potential recovery issues ahead of time. However, most geometallurgical assessments are based on bench- or laboratory-scale analyses of relatively sparse samples, leaving most of the orebody characteristics known only by inference until the rocks are actually mined. In this pilot study, we test drone- and tripod-based hyperspectral imaging for mapping mineralogy across mine highwalls, dumps and leach pads. The results show that hyperspectral imaging can successfully map the types and distribution patterns of key minerals (especially carbonates, sulfates, clays, other phyllosilicates) and other important features (such as lixiviant ponding on leach pads), bringing geometallurgy into the field to provide crucial inputs to process decisions.

By William C. Larson

The Bureau of Mines, as a result of its contract research program, is developing a retractable core bit for the wireline drilling system (Retractable Sit System, No, H0272004). The prime contractor, Longyear Company, Minneapolis, Minnesota, and the subcontractor, Doerfer Division, Cedar Falls, Iowa, have designed, fabricated, and are currently field testing the in-hole retractable bit system. he objective of the program is to develop a minerals exploration core drilling system that allows retraction of a worn out bit and insertion of a new core bit, without pulling the drill rods out of the hole. To date, the results of the project are encouraging, and the retractable bit contract is currently in the last phase of a four-phase program, which is on schedule and under budget.

Jan 1, 1980

By Kevin J. Ashley

Coal is deposited at a mine site in several thin seams which outcrop in rolling hills and dip at about 8° to the northeast. The deposit is located in the northeast area of the State of New Mexico in the Southwest of the United States. A drilling program was undertaken and was quite irregular. Not all of the seams appear in all of the drill holes. Some of the holes did not go deep enough, while others were drilled below the outcrop of some seams. Occasionally a seam would pinch out and not be seen in a drill hole. Also, the outcrops of the seams are buried in many places by several feet of alluvium. All of these factors make correlation of the seams between drill holes difficult. The drawing of cross sections in three directions and at many locations across the mining area have been necessary to assure the accuracy of the input data.

Jan 1, 1982

By Michael von Seebach

High-pressure grinding rolls subject the feed material to pressures of 200 N/mm? During this process considerable size reduction and the Formation of flakes occur. This paper describes the basic consideration For design and operating of this type of mill. It is also shown that the particle size distribution resulting from this process is typical for grinding processes but untypical for crushing processes. High pressure grinding rolls are designed in size of up to 2.8 m roll diameter allowing feed material top sizes of 250 mm. The rigid frame, bearing and drive - train design allows a broad application of the high-pressure grinding rolls operating the machine in open or semi-closed and closed circuit for dry and moist feed materials. Operating results show that capacity increases of up to 100 % can be accomplished with this technology. The high-pressure grinding roll also, allows for lower operating and maintenance costs due to energy savings of up to 20 L and reduction of wear to less than 1 76 for dry and less than 0.1 5 for wet grinding. Other advantages of the high-pressure grinding rolls are smaller equipment sizes than a ball or SAG-mill for a given capacity resulting in lower building sizes with reduced capital in- vestment costs.

Jan 1, 1987

By V. F. Hollister

Computer programs developed as part of the PROSPECTOR project at SRI International can indicate where the highest grade hypogene copper occurs in porphyry copper prospects. The programs are useful in selecting drilling targets in untested porphyry deposits. Because of mineralogic, structural and lithologic variations in porphyry-type deposits, three distinct computer programs have been constructed; however, this paper considers only the stockwork type in homogeneous rock (similar to the Lowell and Guilbert model). The programs represent models in the form of inference networks that utilize the mineralogic, alteration, lithologic, structural, geochemical and geophysical data normally collected prior to a drilling decision. One example of an application of the PROSPECTOR program for a stockwork-homogeneous porphyry is given: Island Cooper in British Columbia. Computations based on the surface geologic, geochemical and geophysical data for Island Copper clearly disclose the best hypogene grade of the deposit. Other deposits were tested in the programs as well, and in each case PROSPECTOR programs indicate the region with the highest hypogene grade.

Jan 1, 1983

By Rao Balusu, Bharath Belle, Krishna Tanguturi

A collaborative research project is undertaken by Anglo American Coal and CSIRO to develop appropriate strategies for gas and spontaneous combustion management of longer panels. Extensive computational fluid dynamics (CFD) modelling studies have been conducted and calibrated using operational longwall goaf gas data to obtain a fundamental understanding of goaf gas flow patterns in longwall panels of 1.0-km and 3.0-km lengths and a detailed investigation of the effect of various mining and operational parameters on goaf gas flow patterns. The modelling studies have also been used to investigate the performance of various gas drainage and proactive inertisation strategies during various stages of longwall panel extraction. Simulation results indicated that apart from tailgate (TG) side goaf holes, gas drainage from maingate (MG) goaf holes and the mid panel start-up goaf holes would be useful for flat seam field conditions. Operation of 8–10 goaf holes is recommended for field site conditions with high goaf gas emissions of 6000 L/s. The modelling results indicated that the traditional inert gas flow rate of 500 L/s currently used in some mines would be insufficient to achieve effective goaf inertisation in long panels. Results indicate that 3.0- km-long panels would require 1500 L/s of inert gas and there is a need for multi-point inert gas injection strategy for effective goaf inertisation. In this paper, details and results of modelling investigations and recommended strategies for gas and spontaneous combustion management in 1.0-km- and 3.0-km-long panels are presented.

By Richard E. Ellwanger

Methods of utilizing flocculants as settling and filter aids for mineral processing slurries are reviewed. Broad chemical classifications and techniques for proper dilution, multiple addition, and combination treatments are discussed. A variety of custom built and commercially available systems for make up and delivery of flocculants to the application points are in use through- out the mining industry. Those concepts which, in the author's opinion, are particularly important to the successful make up and use of flocculants are presented in relationship to the available make up and feed systems. Actual industrial applications are included in the presentation.

Jan 1, 1980

By Peter Zhang, Daniel Su, Mark Alexander Van Dyke, Heather Dougherty, Bo Hyun Kim

The National Institute for Occupational Safety and Health (NIOSH) has been evaluating longwall mining-induced strata fractures and their impacts on casing stability of Marcellus shale gas wells located in longwall pillars. To understand the extent of overburden fractures after longwall mining, NIOSH researchers drilled a post-mining corehole into the fractured strata above the Pittsburgh coal seam longwall gob. Knowing the extent of the fracture zone height will help gas operators minimize the hazards of drilling into longwall gobs. The core was retrieved from the surface down to the top of the gob void. Various fractures were encountered varying from 35 to 64°, depending on lithologic type and relative closeness to the gob. The longwall panel dimension was 457-m wide and 3657-m long, in which the total fracture zone height was found to be at 141 m and the hydraulic connected fracture zone at 87.7 m above the top of the Pittsburgh seam. In addition to core drilling through the gob, FLAC3D modeling was also used to simulate the formation of fracture zone and the orientations of longwall-induced fractures. This study provides much-needed evidence on the fracture zone of Pittsburgh seam longwall gobs to help gas operators avoid potential hazards associated with drilling through highly fractured zones in longwall gobs.

Jun 9, 2022

By Justin R. Patts, Andrew B. Cecala, A. KYLE LOUK, Emily J. Haas

The U.S. National Institute for Occupational Safety and Health (NIOSH) and the former U.S. Bureau of Mines (USBM) have put significant effort over the past four decades into researching and developing engineering controls and interventions to reduce mine workers’ dust exposures during the bagging and palletizing of industrial minerals. Workers who perform the manual bagging and palletizing of 50- to 100-lb bags typically have some of the highest dust exposures of all workers at mining and mineral processing operations. This paper provides an overview of available dust control technologies for bagging operations and presents the findings of a recent case study conducted at four industrial sand operations to identify the current types of bagging and palletizing technologies being used and to evaluate their effectiveness in reducing workers’ exposures to respirable crystalline silica dust. An evaluation is also performed to determine if further reductions in respirable dust levels can be achieved by incorporating additional modifications or improvements into the existing technology.

By C. E. Jordan

The fundamental properties of the Bureau of Mines patented dielectric separator were studied to provide insight regarding its design and operating characteristics. Force equations for mineral particles were derived and evaluated experimentally. High dielectric mineral recovery was proportional to the calculated effective dielectric force volume that surrounded each drum electrode wire. Electrode spacing was the most sensitive design parameter, requiring less than 0.4-cm electrode spacing for a good separation. Operating characteristics and ore characteristics were investigated. With a dielectric constant difference as small as 2, good separations were made on a laboratory scale at energy consumption below 12 kw?h/mt.

Jan 1, 1985

By John H. Clark

This paper outlines new technological improvements in underground trackless equipment for the metal mining industry with emphasis on maintenance related developments for Load Haul Dump machines. Also new developments on other types of equipment are covered including drills, road headers and electric LHD's.

Jan 1, 1983

By C. Haycocks

The Appalachian coal fields contain many mineable contiguously placed coal seams. Selection of the mining sequence for these seams, historically and currently, is based primarily on considerations of seam ownership, availability and economics. Mining any seam can seriously affect subsequent operations in coal seams both above and below the one being mined. The effect is often detrimental to recovery costs and safety of mining in the subsequent seams. The purpose of this paper is to examine the conditions that can develop in an underlying seam due to stress concentrations that can occur below pillars or abutment zones in an overlying seam, and suggest guidelines for avoiding them. This situation most commonly occurs when the overlying seam is mined first, although simultaneous and subsequent mining of the upper seam can also produce such effects. Other interaction phenomena resulting from subsidence or arching will not be considered here. The methodology used in this research utilized both computer and body loaded photoelastic models to study the interaction mechanisms. Field studies are used in both interpretation and analysis of the results. Numerous examples of load transfer from upper workings exist in all parts of the world and many of these have been incorporated into this work. Such interaction problems are quite common and likely to be an ever increasing occurrence as mining activities in old seams are completed and new seams opened up.

Jan 1, 1982

"Tell us how you got involved in mining and about your career path.My dad was a coal miner and my uncle was a metallurgist, so when I enrolled at Penn State’s New Kensington Campus, I chose the College of Earth and Mineral Sciences — exact majors didn’t get picked till the end of your sophomore year. Penn State New Ken had an associate degree in mining program and one of the guys in my carpool was going to take Mining 30 in the evening and the other guy (mechanical engineer) was also able to take an evening class. I didn’t want to break up the carpool, so I took Mining 30, complete with essay tests. I could write, so I did well, and the professor said I should go into mining engineering. Fast forward to the end of the next term at University Park, and I realized there wasn’t enough chemistry in mining. Switching to metallurgy would have meant another term at that point, so Dr. Lovell, my advisor, trotted me down the hall and to the next building and said I was a mineral processor. That stuck. I was a summer student at U.S. Steel Research between my junior and senior year and they paid for my master’s degree — all about clay and macerals in coal flotation. During that time, the steel industry tanked, and I thought a Ph.D. would be a good idea — I could always teach at the university level if I had those credentials. The Electric Power Research Institute had a Coal Cleaning Test Facility in Homer City, PA, and I conducted my Ph.D. research on rate and residence time in conventional coal froth flotation cells there and at a local cleaning plant. I went to work at the test facility in 1987 (later CQ Inc.) and stayed there until I started PrepTech Inc. in 1997. PrepTech offers some consulting services for coal cleaning plants and sells mineral processing equipment, mostly to coal companies. I can’t believe it’s been 21 years.And what about your SME career?Of course, I was a student SME member at Penn State. We used many of the SME books in class, so who wouldn’t want the student discount? While in Homer City, I became involved with the Appalachian Plateau Subsection of the Pittsburgh Section. We’d hold quarterly meetings with interesting speakers and had good attendance. I was the secretary. I’m still the secretary and also get the bank statements. We’ll need to close that out some time, but I guess I’ve been hoping for resurgence in the Indiana/Cambria/ Somerset area."

Jan 3, 2018

"2016 marks an amazing accomplishment in the mining industry as Hecla Mining Company celebrates its 125th anniversary. Mining Engineering sat down with Hecla chief executive officer Phil Baker to gain insight on this tremendous longevity and to get his view on how the company demonstrated persistence, gained perspective and created position for its future.How did Hecla Mining Co. get its start?In 1891, a group of investors formed Hecla Mining Co. to acquire and trade mining claims. No one envisioned at the time that the Coeur d’Alene Mining District would become known as the “Silver Valley” and produce more than 37.2 kt (1.2 billion oz) of silver. Or that Hecla would become the United States’ largest primary silver producer and the last of the pioneer mining companies from this illustrious mining district.What is the origin of the name “Hecla?”That will forever be a bit of a mystery. Some say it was named for an Icelandic volcano. Or that it was the foresight of James Toner, who staked the original claim, that it would go so deep, fulfilling the medieval folklore definition of the word ‘Hekla’ which is the ‘Gateway to Hell.’ I kind of like that one as the Lucky Friday Mine is almost 3.2 km (2 miles) below the surface. It has operated for more than 70 years and has all the markings of being one of only a handful of mines that will exceed 100 years of operations.Is there a common theme, or thread throughout the 125 years?Yes, Hecla has always had a solid core of high-quality and long-lived assets, positioning the company to survive times of low prices and reap the rewards when cycles turn and higher prices are realized. But it is not just assets. Hecla has extraordinary expertise that gives us the perspective of how to acquire, explore, develop and operate mining assets, particularly underground. Hecla is one of the few companies to acquire assets in the last five to six years and we did not have to write down the value of them, which means we paid a fair price for the asset despite the metals price reductions that followed the purchase. And our culture has given us the persistence to develop mines and complete projects despite lower prices. For almost a decade we have been advancing the #4 Shaft project at the Lucky Friday. We will complete this project this year, positioning the mine to operate for decades. We have elected to spend capital on San Sebastian (Durango, Mexico) and Casa Berardi (La Sarre, Quebec, Canada) to start a new mine and increase production, respectively. And we are spending money on new techniques, new equipment and innovations to our operations. Our insistence is on developing for the future, and our persistence in doing so is in contrast to many companies that are reducing investment and shrinking production"

Jun 1, 2016

By Thomas F. Clemens

This paper covers various changes in government regulations, taxation, and legislation for the past two plus years and the up- coming one. Part of the paper will discuss recent business conditions and how they have affected the cement and lime industry.

Jan 1, 1983