Search Documents

By Rodolfo V. de la Cruz

The stresses in the materials surrounding an underground opening are dependent upon the virgin stress field, the geometry of the opening and changes in boundary conditions as mining progresses. For most underground openings especially in coal mines, roof bolts are installed to help stabilize the opening. While most parameters in roof bolt design and installation have been thoroughly investigated, the effects of the initial stress field on the effectiveness of roof bolts have not been recognized. This paper summarizes the results of investigation of the effect of the initial stress field on the performance of mine roof bolts. Roof bolt installations are duplicated in the laboratory utilizing conventional roof bolt frame, commercial roof bolts and shells, mine torque wrench and encapsulated rock specimens for anchorage. A special and primary feature of the laboratory set-up is the addition of a loading system for generating stresses at the anchorage specimens. For this preliminary study, different levels of hydrostatic stress fields were induced at the anchorage specimen, instrumented roof bolts were installed in the usual manner, and the bolt load loss-with-time observed. Statistical analysis of data showed that the stress field at the anchorage horizon has a considerable influence on the performance of mine roof bolts, i.e. the higher the stress field, the higher the anchorage efficiency. From this observation, methods of improving the performance of mine roof bolts utilizing new shell designs and methods of installing them are suggested.

Jan 1, 1978

By Bill Kendall

"In coal mines, handheld air, electric and hydraulic powered drills are used along belt conveyors, in single entry development, in entries where there are obstructions, and in longwall recovering bolting. In hard rock mines, pneumatically powered jackleg drills are typically used in narrow vein mining. Drilling and bolting in narrow confines has traditionally been performed with pneumatically or hydraulically powered hand-held drills or newer electrically powered hand- held hammer drills due to their low cost, simplicity of operation, and extreme flexibility due to their small size. Mechanized equipment has typically been too large, too expensive, inefficient due to the confined space, and too restrictive due to lack of flexibility for use in narrow confines.Although the handheld equipment is effective, it requires operator exposure to certain inherent hazardous conditions in use. These include falling rock from the roof, rib and face; tripping hazards; bending twisting lifting hazards; high noise levels and chemical fumes from the pneumatic exhaust. The operation of the hand held equipment can adversely affect the long-term health of the operator - continual jackleg operation frequently results in longterm damage to hearing, shoulders, arms and wrist joints and back injuries. This results in a reduction in life style for the operator and higher personnel turnover rates for the mining company.Hand-held drills also typically have limited thrust and torque capability that limits their ability to push long resin bolts, inadequate torque to properly install resin bolts or to properly torque mechanical or tensioned rebar bolts. Hand-held drills do not offer any type of protection for the operator from roof or rib falls. They do not offer any means for handling roof or rib mesh. Since the operator stands on the ground the maximum safe drilling height without use of a ladder or "riding the drill" is limited to 2.44 m (8 ft)."

Jan 1, 2014

By R. A. Pimentel

Complying with reduced dust standards (i.e., less than 2.0 mg/m3) due to quartz levels that exceed 5 percent is presently a critical problem for many continuous mining sections. Results are presented of research which was performed to determine the factors causing high levels of respirable quartz dust and to identify the major contributors to operator exposure. It was found that the significant sources of quartz dust are the drilling of the roof and the mining of the roof, floor and rock bands. Both the miner and the bolter may be on a reduced standard, but compliance is easiest to achieve on the bolter for which improvements in maintenance and operator practices are usually sufficient. At the miner, the problem is more elusive. Research continues to identify operating and mining practices that contribute to the exposure..

Jan 1, 1985

By Robert E. Murray

The title of my paper, "A Company's Response to Federal Coal Leasing," brings to mind a picture of a dog chasing its tail. This is what the coal industry, has been doing since the Federal coal leasing moratorium went into effect in 1971. We've gone around in many circles, but we are only very slowly, if at all, getting closer to catching our tails, i.e., efficient, economical, and rational Federal coal leasing. My companies, The North American Coal Corporation and its four Subsidiaries, The Falkirk and Western Plains Mining Companies and The Coteau and Missouri Valley Properties Companies, together hold in excess of 4.5 billion tons of lignite reserves in North Dakota. Some of our North Dakota properties are substantially interspersed with Federal coal, with the government holding title to the minerals in every other section. This checkerboard pattern of Federal ownership has made it difficult to develop and market some of our reserves, and, as a result, it has become imperative that we be familiar with and active in the Federal Coal Leasing Program.

Jan 1, 1982

By J. Noll, A. Miller, J. Volkwein, C. Pritchard

Hecla Limited, Magee Scientific, and NIOSH have combined efforts to evaluate an in-situ air filtration system for use in an underground mine environment. The purpose of the collaboration was to determine the efficacy of such a technology for reducing the concentration of airborne diesel particulate matter (DPM), with the aim of improving air quality in underground hardrock mines. A secondary goal was to evaluate the use of an Aethalometer as a means of real-time measurement of black carbon as a surrogate for DPM. The evaluation included measuring the DPM-capture efficiency of the filter when it was pre-loaded with dust. Toward this end, rock dust was introduced at the filter inlet to create a dust layer on the filter surface, with the intent of providing improved capture of the much smaller DPM particles. The filtration efficiency for DPM was assessed by comparing measurements of DPM taken at the inlet and outlet of the system, using both real-time and time-weighted-average approaches. The real-time measurements were performed with the model AE33 Aethalometer® made by Magee Scientific. The results of the NIOSH 5040 method analysis were used to assess the effects of the system on time-weighted-average concentrations of total carbon. Results showed a reduction in DPM concentrations in the range of 82%-89%. While the calculated efficiencies based on the two different measurement methods were similar, the DPM levels reported by the Aethalometer were higher, possibly due to differences in the performance of the size-selectors used for the two methods (impactors versus cyclones). More research is required to develop a robust correlation between the two methods, to support the use of the Aethalometer for future mining applications. The advantage of the Aethalometer is that it can measure and record DPM levels for weeks at a time, and can be directly connected to a mine monitoring system, potentially at multiple locations. Ideally such data can be used to initiate the startup of the filtration system should DPM concentrations reach an action level. This work demonstrated that in-situ filtration systems, modified to collect DPM and coupled with real-time monitoring, show promise at reducing DPM concentrations in the mine environment.

Jan 1, 2016

By Gordon O. Prickett

In two case studies we look at strategies of acceptance that the analyst can employ to gain entrance and to see his problem solution out to use. The first example comes from metal mines. The problem area was excessive usage and cost of wear parts in the concentrator and an atmosphere of crisis over frequent and unexpected breakdowns. The second case pertains to coal exploration. Better methods were being sought for representing coal quality in developing reserve tonnages. The first strategy is - Develop a detailed Human Impact Statement. The second strategy is - Write down in plain language with the keeper of the problem what he will consider as success in dealing with his problem.

Jan 1, 1978

By Bryan Ulrich

On March 20, 2014, the ?Roundtable Discussion on Innovations in Heap Leaching and Mine Waste Management? was hosted by Knight Piésold and Co. at the Red Lion Hotel in Elko, NV. This topic is timely, and formed something of a lead into the inaugural ?Workshop on Innovations in Waste Rock, Tails and Heap Leach Management.? That workshop, which grew from the 2013 Elko Roundtable, was held on the University of Nevada, Reno (UNR) campus on May 19, 2014. The workshop was hosted by UNR and the University of British Columbia. Knight Piésold?s local representatives, Bryan Ulrich and Logan Jensen, were joined by Tom Kerr, president of Knight Piésold?s, U.S. practice; Rick Frechette, senior vice president, environmental services and Jeff Coffin, geotechnical engineer, from the Denver, CO office for the roundtable event. The event played host to about two dozen attendees from several western states.

By Randhir Sehgal

Heavy media processes have been used for cleaning +28 mesh coals for a number of years, Two applications, i.e., the vessels and the cyclones are widely used in the U. S. for this purpose. The basic reason for the popularity of these systems is their extremely high efficiencies for particle sizes above 28 mesh, However, application of heavy media technology to fine coals below 28 mesh, has been limited due to the following reasons: o Inability to make size separations effectively at sizes below 28 mesh o Necessity of feeding large quantitites of magnetite to the separators o Difficulty of recovering magnetite in the presence of large quantities of coal o High levels of coal contamination in the recovered media, leading to high circulating loads and ineffective control of media gravity

Jan 1, 1981

By George D. Lessner

I'm sure that everyone at this meeting is aware of the current problems facing the U.S. metals mining industry. Prices are depressed and expected to remain depressed for quite some time. On the other hand, industrial minerals, including talc, are doing quite well. The profitability of industrial minerals has sparked considerable interest on the part of many companies in expanding into industrial minerals. Our company is one of those actively seeking to expand its position in industrial minerals. It is appropriate that the A.I.M.E. asked me to speak to you regarding entry into the talc business. So how do you get into the talc business? Earlier speakers have explained how to locate, mine, process, and market talc, so you have the "how ton.

Jan 1, 1984

By G. Karahalios

Industrial minerals always play an important part in the technological growth of a country. The extraction and trading of industrial minerals continues to expand, but the industry is now subject to stricter environmental guidelines. This paper presents the current status and growth potential of industrial mineral exploitation in the southeastern European region, i.e. Albania, Bosnia-Herzegovina, Bulgaria, Croatia, the Former Yugoslav Republic of Macedonia, Greece, Italy, Serbia and Montenegro, Slovenia and Turkey. Annual production figures per country are presented for 1992-1998. These figures are compared to each other, and, where applicable, they are compared to world production figures. The marketing of industrial minerals to Europe and other regions of the world and the effects of such trade on the local economies are also evaluated when such data are available.

Jan 1, 2000

By R. Costa, A. Kozak, B. Fukuhara

Introduction The Jacobina mine is located in the state of Bahia in northeastern Brazil approximately 330 km northwest of the state capital city of Salvador and 9 km from the town of Jacobina. The Jacobina Mine (Figure 1) is owned by Jacobina Mineração e Comércio, a wholly owned subsidiary of Yamana Gold Inc. The gold mineralization of the Jacobina mine is hosted within quartz pebble conglomerate reefs of the Serra do Córrego Formation which together with the Rio do Ouro Formation forms the Serra do Jacobina mountain chain. The Serra do Jacobina mountains have been mined for gold since the late 17th century. Since the 1970’s, the Jacobina mined has been operated by Anglo American, Williams Resources Inc., Desert Sun Mining Inc. and now Yamana Gold Inc.

Jan 1, 2007

By Por J. B. Evans

El mantener un beneficio óptimo sobre todo el conjunto de un emplazamiento minero necesita una constante puesta al día de las estrategias operativas. En esencia, cada estrategia es una combinación particular del gasto del capital previsto, el flujo de ingresos y el tiempo transcurrido. La selección de una estrategia basada en el beneficio potencial requiere que cada estrategia contemplada con un ordenador, un análisis tal puede ser engorroso. Este capítulo discute o desarrolla una técnica de "corte rápido" que asigna una relación de beneficio a las estrategias alternativas e identifica aquellos aspectos de una estrategia que producen mayor impacto sobre el beneficio. Esta técnica puede proporcionar valoraciones rápidas de suficiente precision para muchas de las decisiones de las estrategias operativas que se toman sobre la marcha en minas que se encuentran en explotación.

Jan 1, 1982

By D. W. Hill

By seeking to define the social and political parameters of both established and potential uses of the underground, this paper will attempt to formulate and state the problem posed in the realms of public choice for obtaining more rapid development and more beneficial use of the underground environments. Essentially, the paper will pursue the following outline: 1. Established policies and established uses of the underground 2. Potential uses of the underground for social benefit 3. Constraints on development and policy a. Psychological constraints b. R & D plus physical constraints c. Economic constraints d. Public choice and policy contraints (both governmental and non-governmental) e. Legal and other structural constraints 4. Defining the problem from the social standpoint 5. Suggestions for surmounting the constraints and meeting the problem: some hypotheses for the future.

Jan 1, 1974

By P. B. Moran, J. W. Rozelle, J. Forbort

"The Mount Todd gold mine is located approximately 50 km (31 miles) north of the town of Katherine in the Northern Territory (NT) of Australia just off the Stewart Highway, and was operated in the 1990s until 2000 (Fig. 1). After cessation of mining operations, meteoric precipitation and acid rock drainage (ARD) associated with surface water runoff continued to report to the retention ponds across the mine site. In 2000, the mine site entered receivership and the NT government became responsible for the care and maintenance program. In 2006, Vista Gold Corp. (as Vista Gold Australia) acquired the rights to resume exploration on the mine site without the financial responsibility of the environmental liability. In January 2007, Vista Gold assumed the care and maintenance activities on behalf of the NT government, with the environmental liability remaining with the NT government, with the goal of reinitiating mining operations. A critical path component of the planned upgrades to the existing mine/milling facilities and infrastructure was the development of a cost effective treatment and dewatering program for the approximately 11 GL (2,900 million gal) of ARD stored in the Batman Pit (RP3), which has a maximum capacity of approximately 12 GL (3,200 million gal). The Batman Pit must be dewatered in order for Vista Gold to restart mining activities. The Batman Pit Lake had reached a maximum water depth of 104 m (341 ft) when Vista Gold initiated water level monitoring. It is important to note that the ARD water in the Batman Pit has been pumped into it from 2000 to 2012 under an NT government-approved environmental control program.The Batman Pit has virtually no connection to the local ground water regime due to the intensive silicification that accompanied the mineralizing event. In October 2012, just prior to treatment, the pit lake profile was characterized by uniform acidic pH (approximately pH 3.2) and oxic conditions (dissolved oxygen greater than 7 mg/L with depth (Fig. 2). The temperature decreased by approximately 4 °C (39 °F) between the lake surface and approximately 20 m (66 ft) deep, and remained near constant with increasing depth. This temperature difference is believed to be associated with an existing shallow mine bench at approximately 20 m (66 ft) deep around the perimeter of the pit. Similarly, electrical conductivity, an estimate of total dissolved solids, decreased by about 85 microSiemens per centimeter (µS/cm) from 2,800 to 2,715 µS/cm between 10 and 20 m (33 and 66 ft)."

Apr 1, 2016

By Stuart Lister

"When MacLean Engineering chairman and founder Don MacLean got the first question from a minesite about the possibility of addressing ventilation limits through incremental fleet electrification, he was intrigued. It was back in 2015, and the MacLean scissor bolter was already diesel-electric (jumbo trailing cable), so it made sense to him that if they could engineer a battery drive system for the unit’s tramming cycle, they would have the inaugural electric vehicle (EV) MacLean unit.At that time, there were not any entirely diesel-free hard rock mines in existence on the planet, and that remains the case to this day — although the Borden project in northern Ontario is progressing toward that goal (see page 33). This meant there was essentially zero market demand for battery electric vehicles as well as a complete lack of battery technology to address the battery electrification of heavy haulage. Heavy haulage is the part of a typical mine’s mobile fleet with the largest footprint when it comes to diesel particulate emissions, greenhouse gases and wasted energy in the form of heat.Three years later — the wave of battery electrification that is currently picking up speed across the mining industry promises to hit full swing by the early 2020s when a slew of new build, diesel-free mines will start construction. But this movement toward emissions-free mobile fleets is not a completely new phenomenon. Instead, it is an updating of mining technology from a previous generation. What is going on now is the re-electrification of mining. Up until the 1960s, early generations of battery technology (lead acid) and electric locomotive systems were the norm for material and ore haulage in Canada and elsewhere.The thought of a coming paradigm change in mining was particularly pertinent to Don MacLean back in 2015, as he had been part of the era that ushered in the first generation of rubber-tire diesel equipment, when he was a divisional foreman with Inco in Sudbury in the 1970s. He was part of the operating team that was tasked to build a rail loop on one extraction level of the mine. At that time, events on the ground overtook the project, as diesel-powered mobile equipment became a viable option. Once the first diesel scoop was introduced at Creighton #3 shaft, it was clear what the power, haulage capacity and mobility could do for operations and that era of electric rail haulage underground was effectively over."

Jan 10, 2018

By N. Ward

The Gualcamayo Mine is located in the Andes Mountains north of San Juan, Argentina (Fig. 1). A property of Yamana Gold Inc., it declared commercial production in July 2009 and has a total mineral reserve and resource base of approximately 88 t (3.1 million oz) of gold. Crushing operations for the openpit mine are located in a 13,500-m3 (477,000-cu ft) underground cavern with a ceiling height of 22 m (72 ft). More than 3,600 m (11,800 ft) of tunnels are used to access the cavern and convey the ore. The project as described in this paper relates to the design and construction of the main cavern, conveyor system exit tunnel, the mechanical system access tunnels and two 4.2-m- (13.7-ft-) diameter shafts (Ore Pass #1 and Ore Pass #2) (Fig. 2). Preliminary engineering for the project was performed by Hatch Chile. Rizzo Associates Argentina, S.A., a division of Paul C. Rizzo Associates, Inc. (Rizzo), was contracted to provide geomechanical and geotechnical support for the construction of the access tunnel system and geomechanical design and construction supervision for the cavern and shafts.

Jan 1, 2011

By William W. Edgerton

Establishing geotechnical baselines on soft ground projects that require the use of closed-face tunnel boring machines (TBMs) is difficult. It is hard to see the face when mining and the excavated material is combined and mixed, all of which makes baseline quantifications challenging. In an attempt to meet underlying objectives of minimizing bidder contingencies, allocating or sharing risks and paying for conditions only if they occur, nongeotechnical baselines (i.e., functional baselines) have been developed. These have been used on the District of Columbia Water and Sewer Authority?s Clean Rivers (DCCR) Blue Plains Tunnel (BPT) project. This article examines the development of such functional baselines and how they were implemented on the BPT project.

Jan 1, 2012

By J. Lorengo, C. H. Bucknam

"Standardization of the Inductively Coupled Plasma Mass Spectrometry (ICPMS) method for gold in cyanide solutions was undertaken to provide a more sensitive method to quantify the gold content than the atomic absorption method standardized in 1994 (E1600). The gold concentration range covered is from 0.001 mg/L Au - 0.3 mg/L Au (0.00005 toz/t Au – 0.009 toz/t Au). Interlaboratory testing was carried out with the assistance of the American Society of Testing and Materials (ASTM) International on two committees to determine the within laboratory and between laboratory reproducibility. Three barren solutions from metallurgical operations were measured in triplicate to satisfy statistical requirements for Committee E1 on Analytical Chemistry of Metals, Ores and Related Materials. A synthetically prepared matrix representing the metallurgical processing solutions was used to prepare Youden pairs to satisfy the requirements of Committee D19 on Water. Results of the standardization program are presented. INTRODUCTION Analysis of process solutions for gold concentration requires accurate and sensitive analytical methods in order to manage process control and metallurgical accounting. Flame atomic absorption spectrophotometry (FAAS) has been the work horse of the assay lab for this duty for decades. In 1994 the FAAS standard method was approved by the American Society for Testing and Materials (ASTM) (1). Six process solutions were collected and preserved by measuring the pH and adjusting to greater than pH 10, if necessary. Duplicate solutions were provided to eight laboratories in random order for analysis by FAAS covering the gold concentration range of 0.19 µg/mL (0.006 toz/t.) to 10.7 µg/mL (0.312 toz/t). A high precision method was used, which involved bracketing the sample with the higher and lower standards nearest to its concentration repeating readings three times and averaging the results. The optimum precision for the FAAS gold method was found to be at the 1.00 µg/mL (0.029 toz/t) and lower scope limit 0.3 µg/mL (0.009 toz/t) gold concentration. Since tailings solutions typically have concentrations below the lower scope limit, use of ICPMS was developed at Newmont USA Limited (Newmont) to assay the lower range solutions."

Jan 1, 2016

By Grover Wallace

At is important for today?s mining executives and leaders not to underestimate the fact that, while the recent downturn in the economy did take its toll on balance sheets and productivity, factors such as emerging countries, aging workforces, globalization and individual knowledge growth did not lay dormant while the economy was in a lull. It is key for mining leaders to be proactive in their talent strategies. Successful mining companies are developing a clear, concise and communicated strategy and placing a high priority on recruiting the right talent in global markets that parallels their business strategy. They are focused on placing the right people in the right jobs.

Jan 1, 2011

By V. C. Rogers, K. K. Nielson

INTRODUCTION The potential health impact from uranium milling operations is mainly associated with long-term releases of radioactive contaminants from the mill tailings.(1,2) The major mechanisms for mitigating these potential releases focus on increasing the tailings containment with the addition of migration barriers such as thick earthen covers and clay liners. Some limited investigation has also focused on reducing the radionuclide source terms. This alternative approach has some desirable features, but stringent cost requirements are placed upon source removal methods in order for them to be economically favorable. A cost effectiveness evaluation is presented herein, in which costs for containment methods are used to establish maximum cost guidelines for the source removal methods. The 230U decay chain, shown in Figure 1 contains the radioisotopes of major concern, 230Th, 226Ra, 222Rn and its short-lived alpha-emitting daughters, When the uranium is removed in the milling process, these isotopes, which are normally not removed remain in the tailings solids. The general pathways to the environment from uranium mill tailings are depicted in Figure 2. The dominant pathways are radon to the atmosphere and radium and thorium to a groundwater aquifer. The magnitude of the contaminants released into these pathways can be characterized by the following parameters: 1. The 230Th and 226Ra content. 2. The emanating power for radon. The fraction of radon generated that is free to migrate. 3. The leach rates. Source reduction methods seek to reduce the magnitude of any or all of these parameters. In general the dose rates are proportional to the source terms. For radon production the source term is proportional to the product of the radium concentration, R, and the emanating power, E, so that the risk is reduced by the same factor that reduces RE. For example, if the radium content is reduced by 95 percent, but E is increased by a factor of two, then the dose rates are reduced by an order of magnitude. The source term for the groundwater pathway is not as easy to identify. The peak in the radium concentrations in the accessable water body can also

Jan 1, 1981