Search Documents

By J. Girard-Dwyer, J. Johnson, J. Whyatt

The choice of fragmentation method is one of the most fundamental aspects of mine design, and often has a major impact on the safety and economic viability of an operation. Almost exclusively, underground mining operations rely on either mechanical excavation or drill and blast techniques to extract rock. Each of these fragmentation methods has distinct advantages and disadvantages, and each is appropriate, and economic, for different mining conditions. However, the choice of fragmentation method can have a pronounced effect on the amount of damage created in the rock mass surrounding the opening. This paper reviews a number of case studies where both mechanical excavation and traditional drill and blast were used in underground mines. Ground support requirements in the mechanically excavated areas are compared to the support requirements in the blasted sections in order to demonstrate the potential safety and cost benefits of the various fragmentation methods.

Jan 1, 2003

By Bradford F. Townsend, Robin B. Dill, Richard M. Croswell

Innovative geotechnical construction techniques were used to construct three pedestrian tunnels under a building slab-on-grade to allow utilization of basement space for manufacturing. Tunnels were constructed using mining techniques through granular fill soils less than three feet below on-going sensitive manufacturing operations. Project design consisted of jet grout underpinning of exterior foundation walls and an arch of drilled-in grouted horizontal dowels for soil pre-support to limit ground movements during excavation. Permanent tunnel lining consisted of arched steel rib sets and invert struts supported on precast footings encased in cast-in-place concrete slab and side walls and a gunite arch.

Jan 1, 1993

By J. H. Bassarear, P. F. Thomas

Large-scale equipment can reduce both capital and operating costs for concentrators. Large semiautogemus (SAG) mills can be effectively utilized in big mills but they must be kept fully loaded to tab advantage of their great potential. With varying hardness ores, controlling throughput is difficult and careful design must take this into consideration. A variable speed drive on large primary semiautogemus mills can overcome this problem to a considerable degree. This paper provides a base case using standard accepted technology of two wound rotor single speed 4476 kW (6000 hp) motors to drive the primary SAG mills of a hypothetical 36,364 t/d (40,000 stpd) typical porphyry copper mill. One other fixed speed drive will be described and jive variable speed drive configurations will be reviewed. Capital costs for the entire grinding circuit, from crusher product to flotation feed, were developed for the base case and each of the alternatives. A technical evaluation comparing the advantages and disadvantages of each drive is presented.

Jan 1, 1987

By Hong Zhang, Quanming Li, Gang Li

China, a globally recognized major mining country, holds one of the largest quantities of tailings pond country in the world. The total number of mines in China has been ranked first in the world. It is a major concern for Chinese safety management to give great importance for tailings pond safety, stability and sustainable development. For the past few years, China has increased efforts to investigate and govern discrete issues of tailings and to carry out a series of special renovation and comprehensive treatment actions to improve safety management levels and to decrease the likelihood of tailings pond accidents. In the end of 2015, China successfully eliminated hazardous tailings ponds and dangerous tailings ponds. Moreover, the total number of tailings decreased from 12,273 to 8,869. However, there are still 1,425 "head-top" tailings that threaten the lower masses’ safety. This greatly signifies the Chinese tailings pond safety, stability as well as sustainable development. In turn, this may improve the Chinese tailings life cycle safety management system and help reach the goal of attaining closed-loop management in the tailings pond life cycle. Based on the summary of the tailings pond accidents in both China and other countries from 1961 to 2015, and by analyzing the types and causes of accident, this paper investigated the successful experiences and effective measurements of British Columbia (Canada) and Australia in the tailings pond life cycle safety management. This paper summed up each country’s tailings life cycle safety management requirements and analysed the characteristics and differences of tailings safety management by comparing 5 aspects: tailings life cycle safety management process, main design parameter, construction requirements, monitoring, and the tailings pond closing management. Based on these observations, this paper suggests some measurements to improve the tailings pond life cycle safety management in China, such as strengthening tailings pond safety management, improving tailings classification, increasing design parameter values, establishing mine reclamation fund, and so on.

Jan 1, 2017

By H. H. Murray

Tactical R & D is research and development for a specific application or applications. The mineral scientist has to define and understand the physical and chemical parameters required for a specific or potential application. Then the researcher must know the structure and composition of the mineral and its physical and chemical properties. Can these properties be changed by processing particle size and shape modification, and surface chemical treatment? Examples of tactical R & D in the industrial minerals area will be described.

Jan 1, 2003

By David B. Cook, James R. Bieke

I. INTRODUCTION Lawyers are a cautious breed; and it might be expected that a paper concerning a broad and complex area of legal regulation, prepared by lawyers for presentation to a predominantly non-legal audience, would commence with several caveats. Ours are the following: First, we have written a broad (and, in some instances, simplified) overview of the regulatory system and of some of the more important requirements generally applicable to uranium mine and mill wastes in the United States. Our paper is not a legal opinion setting forth all of the governmental requirements that would have to be met by any particular mine or mill. Similarly, we do not imply that the requirements we mention are necessarily applicable to each and every mine and mill in the country; depending on the facts, some of the requirements may be inapplicable or avoidable through exemption or variance proceedings. Compliance decisions and strategies for particular facilities must be considered on a site-specific basis. Second, we have undertaken merely to describe the regulatory framework and some of the generally "applicable" requirements which have been promulgated and proposed by administrative agencies. We express no opinion on whether, under the U.S. Constitution and statutes, the existing and proposed agency regulations are valid in general or as applied to any particular mining or milling operation. There are, of course, procedures for judicial review of agency action; and newly promulgated environmental regulations have frequently been challenged, with varying degrees of success, before the courts. For us even to begin to consider such issues would expand an already forbiddingly long paper to totally unmanageable proportions. Third, in light of the subject of this Conference we have limited our paper to the legal framework and requirements applicable to uranium mine and mill "wastes" -- primarily mine overburden and waste rock and mill tailings (including waste tailings solution). We treat operating discharges (e.g., emissions from yellowcake drying) only peripherally. Fourth and finally, it is important to note that this paper, at least in so far as it concerns the specific requirements of particular regulations, will likely soon be out of date in some important respects. Despite

Jan 1, 1980

By James R. Jones

The concern for air pollution goes back centuries as will be seen from this quotation : "Strife and coal, it seems, have a hand-in-hand historical relationship. It was thought by some . . . in the Middle Ages that burning coal filled the air with dangerous poisons. So great was the concern that in 1306 King Edward I of England passed the first and unquestionably the harshest air pollution legislation edict that history will record. His proclamation declared the use of coal an act punishable by death." As related to coal mining, the air pollution problem is primarily that of its customer when using the fuel. Thus the major impact relates to markets for coal rather than the actual mining operation itself. In the vicinity of the coal mine the problem is principally related to fugitive dust from roads, transfer facilities, loading facilities, crushers, etc., and particulate matter (dust or fly ash) from thermal dryers and air cleaning tables.

Jan 1, 1981

By Gunnar Nord, Per-Anders Persson, Duri Prader

The paper gives a short resumé of the findings of the joint US - Swedish "Mechanical Boring (MB) or Drill and Blast Tunneling (DB) ? Workshop" in Stockholm December 1976. New developments and trends in both MB and DB techniques in Europe since 1976 are described, and information is given on some interesting new projects. Differences in contracting principles between the US and Europe lead to different practices for preinvestigations, design, excavation and arbitration and legal affairs. It is shown that this often leads to a higher cost in the US than in Europe for similar excavation jobs. A typical US tunnel job also has more men on the site than a similar job in Europe. This adds to the cost difference and is only partly balanced by a slightly higher rate of excavation in the US. A comparison is made between two quantitative methods of predicting MB penetration rates. These are in reasonable agreement. A probable future development in machine design is an increase in cutter load towards perhaps 25 tons per disc where the tunnel diameter is large enough to house the machine size dictated by the size of the very large electric motors required. Recent European developments in drill and blast technique include improved methods for cautious blasting, precision hydraulic drilling of small diameter holes, and non-electric interval blasting techniques. These developments still keep the drill and blast method ahead of mechanical boring costwise for tunnels in igneous rock whereas for most sedimentary materials mechanical boring has a lead, particularly for long tunnels.

Jan 1, 1979

By Robert E. McIvor

The “Functional Performance Equation for Ball Milling” was first presented in 1988. It now has been used successfully in more than a dozen mineral processing plants. This powerful, yet simple tool provides a new level of understanding of closed circuit grinding. It shows how grinding circuit efficiency is in reality comprised of two distinct efficiencies. It demonstrates how circuit production rate is related, collectively, to these two efficiencies, mill energy input, and the grindability of the ore. It links circuit performance to design and operating variables that can be manipulated, and creates an effective strategy for making plant improvements. This paper covers the derivation and industrial validation of this equation. As part of an engineering and management system that also incorporates suitable metrics and process control, other operators can now use this tool to make improvements and to manage the performance of their grinding operations with clarity and confidence.

Jan 1, 2005

By U. F. Beichmann

INTRODUCTION The City of Oslo together with the neighbor municipalities, Baerum and Asker, are presently building a jointly owned sewage treatment plant located on the west side of the inner Oslofjord. The project is scheduled for completion late 1981. Because the location of the treatment plant is at a distance of about 20 miles (30 km) from the city center, a discharge of more than 13 yds 3/sec (10 m3/sec.) of sewage and storm water will have to be transported over considerable distances. The topography of the area and the geological conditions early indicated that the only realistic transport method had to be through tunnels. As planning proceeded, full face tunnel boring emerged more and more as a favorable alternative to conventional drill and blast medhods. Today the scheme comprises nearly 25 miles (40 km) of tunnels being excavated by full face tunnel borers. In addition a number of access tunnels and cross cuts are to be excavated by conventional methods.

Jan 1, 1979

By X. Wu, M. G. Karfakis, K. Y. Haramy, B. T. Brady

A quantitative evaluation of damage caused by ground motions associated with strong roof caving is presented. The strong roofs are modeled as either cantilevering or bridging beams over continuous elastic foundations that are subject to an exponentially distributed vertical stress. Major factors influencing roof caveability and strain-energy buildup are identified and investigated. A methodology for the evaluation of strain-energy accumulation caused by, an overhanging roof is presented. The potential for mine tremors is determined in terms of the local Richter magnitude (ML), which depends on the seismic energy transformed from the stored strain energy that is released when the roof fails. A particle-velocity model is applied to estimate the damage area associated with roof collapse. A case study from a Utah coal mine shows that estimations of bump severity and the damage area agree well with field observations.

Jan 1, 1997

By R. K. Komarek, F. E. Jr. Briber, G. M. Hanson, Fred D. DeVaney, J. H. Blake, C. L. Matson, T. E. Ban, N. E. Shields, R. D. Frans, R. B. Greenwalt

Metallurgically, the term agglomeration is used to describe processes whose goal is to form balls, briquettes, nodules, flakes, or other sized shaped particles from loose, usually fine, incoherent particles. In practice it includes such varying processes as the briquetting of coal dust and other substances, the balling and induration (heating) of such nonmetallics as cement, fluorspar, lightweight aggregates, etc. It includes such widely used processes as the sintering of nonferrous concentrates, such as those copper, lead, zinc, etc. The agglomeration of specific nonferrous metal concentrates is discussed in detail in the section of this handbook devoted to that particular metal. Agglomeration processes are of particular value to the iron and steel industry where the nature of the primary reduction process, the blast furnace, requires for best results a burden essentially free of fines. This is a change that has taken place since about 1960. Prior to that time many fine unsized ores were fed to the furnace. The development of the pelletizing process gave to the industry a chemically controlled closely sized product that increased the produc¬tion rate and reduced the costs so much that unsized fines are seldom used in modem furnaces. Steel plants produce many fine sized waste products such as fine dust (fine ore coke and gangue) and mill scale. These products, which have a valuable iron content, are usually sin¬tered directly at the plant for reuse. Fine sized ore concentrates are usually pelletized at the mine and shipped as pellets to the steel plant. Common practice in some areas producing natural high grade ores is to screen the ore at the mine to about 3/8 in. The oversize is shipped "as is" and constitutes blast furnace feed. The / in. may be shipped to the steel plant where it may be sintered or otherwise agglomerated. At some mines the fines may be pelletizied prior to shipment. With the development of large ocean ore carriers, and with the transportation of slurried concentrates or fines, a trend has developed of constructing large pelletizing plants or other types of agglomeration plants near large consumption centers (i.e., in the Netherlands or Japan) where ores of many types are brought together, ground if necessary, blended, and agglomerated. As an indication of tonnages of agglomerated materials produced, for iron materials alone (the largest share of the total) production in 1970 in the U.S. was Million gross ton Sinter 40.7 Pellets 43.1 Briquettes, nodules, & others 0.1 Total 83.9 During the 1960s, U.S. production of sinter rose from 40.3 million gross tons in 1961 to a high of 48.7 million in 1964, then settled back to almost the 1961 figure in 1970. Pellet production rose steadily from 14.4 million gross tons in 1961 to the 59.9 figure for 1975. Worldwide, sinter production in 1966 was estimated at 340 million mt (mainly in Europe, Russia, Japan, and the U.S.) and pellet produc¬tion the same year at 64 mt (primarily Canada and the U.S.). World pellet production capacity rose to 200 million tons in 1976.

Jan 1, 1985

By Charles A. Stone, Eric C. Wang

"Top-down wall construction was selected to excavate the tunnel portal headwall areas of the ORB East End Crossing tunnel. Benefits included an expedited construction schedule realized by staging excavation and rock support with development of temporary construction access roads. Rock mass properties, proximity to right-of-way lines, and blasting impacts were considered to design suitable lift heights, intermediate bench locations, and permanent ground support systems to provide supported permanent excavations. Carbonate rock formations contained adverse subsurface geotechnical features including solution cavities, clay seams, weathered joints, pinnacled rock, and boulders, which were addressed by flexibility in design. The resulting over-break conditions and long-term water infiltration issues required economic design solutions. This paper discusses the unique considerations required during design of top-down tunnel portal headwalls excavated in carbonate rock formations including temporary excavation and permanent ground support systems which provided flexibility for unforeseen over-break, minimized construction delays, and provided long-term stability. PROJECT BACKGROUND The East End Crossing is an approximate 8-mile highway connection of the Louisville-Southern Indiana Ohio River Bridges East End Crossing (ORBEE) project. Currently under construction, this connection will link State Road 265 in Indiana with the Gene Snyder Freeway in Kentucky to form an outer loop bypassing the Louisville-Southern Indiana metropolitan area. This highway project features a 2,510-foot long, three-span cable-stayed bridge over the Ohio River, and a 1,680-foot long tunnel. The project, being managed by the Indiana Finance Authority and Indiana Department of Transportation, is scheduled to open to traffic by the end of 2016. The new twin three-lane tunnel under the historic Drumanard Estate requires steep cut excavations for approach and tunnel portal walls on the order of 60 feet deep through overburden soil and carbonate bedrock formations. This paper focuses on the design considerations for the permanent support of the top-down wall construction of the tunnel portal headwalls and approach retaining walls."

Jan 1, 2016

By James A. Finch

The Gaudin lecture is devoted to fundamentals. Given my involvement with column flotation over the last 20 years, this is my topic. I have tried to identify spinoff basic research and provide a personal list of favorites. Two are selected for discussion here. They are single bubble rise and bubble surface area flux. The rationale for such work, as well as some of the findings, are reviewed. Support for fundamental work seems as volatile as the economy (and the link is probably not coincidental). I hope some utility to the minerals industry is evident in the text. Column flotation in its current form originated in the early 1960s. The method was invented by Boutin, patented by Boutin and Tremblay and pursued doggedly by Wheeler. Their aim was to overcome the problem of mechanical entrainment of fine particles in the water carried by the bubbles, which they were convinced contributed to lowering flotation concentrate grades (Wheeler, 1988; Finch and Dobby, 1990). The solution was a combination of columnar geometry, the addition of wash water into a deep froth and the maintenance of an excess of water to the tailings, as compared to the feed (a so-called positive bias). Success at Les Mines Gaspe, Quebec, on cleaning Mo in the early 1980s signaled the start of industrial acceptance, making the column one of the flotation machines of choice today. Over the next 20 years, column applications mushroomed to cover virtually all mineral commodities, as well as nonmineral applications such as soil decontamination, deoiling of water and deinking of recycled paper. In the wake, research groups are continuing to probe the fundamentals, conferences and workshops have been transferring the technology and specialist companies have emerged to service the demand. Innovations were triggered as problems arose (for instance, in gas injection systems) and novel flotation cells, much in vogue in the 1990s, had the door opened. Mechanical cell manufacturers have not been idle - there is nothing like competition to provoke a fresh look at an established business. Flotation-cell technology has probably not seen so much activity since the patent rush in the early days of flotation, which occurred around the turn of the century. For an industry often considered reluctant to risk innovation, this is not a bad record. A good idea will find a place, but patience (not always an innovators strong suit) and careful preparation are required. Two books (Finch and Dobby, 1990; Rubenstein, 1996), three symposia (Sastry, 1988; Agar and Huls, 1991; Gomez and Finch, 1996), and a series of reviews (Dobby and Finch, 1991; Finch and Dobby, 1991; Finch, 1995; Finch et al., 1995) document the period. Like many good ideas, column flotation has been overexposed, and there have been disappointments. In a recent example, columns performing scavenging duty were replaced by mechanical cells (Chong et al., 1998). The further applications stray from the original - to

Jan 1, 1999

By A. J. Hendron, L. L. Oriard

INTRODUCTION Controlled blasting is used at some time during most civil engineering projects where there is rock excavation. Controlled blasting is often necessary because the blasting must take place in the near proximity of adjacent structures. In other instances, the blasting is controlled because a smooth perimeter is desired to minimize rock support and overbreak. The construction of tunnels and shafts for subways, rock excavations for foundations and the excavation of road cuts for interstate highways, sometimes require blasting operations which must be conducted in an urban environment. Unfortunately, blasting operations produce unwanted sounds and vibration along with their beneficial effects. Thus, in the writing of specifications for blasting in an urban environment, potential damage to adjacent structures by ground vibrations must be considered, possible damage to windows from airblasts must be considered, potential damage from fly rock must be considered, and the discomfort to people from ground vibrations, airblast, and noise must be taken into account. The contractor or the owner's engineer is faced with determining the maximum weight of explosives which may be detonated without damage to structures on adjacent property. If the weight of explosive is overestimated, the resulting damage to adjacent structures may result in costly losses. But, if the engineer or contractor is too conservative, and the weight of explosive becomes too restrictive, progress of the project may be curtailed and the cost of excavation will increase accordingly. The potential for damaging adjacent property is becoming more important in construction operations today. In the past, the plaintiff had to prove negligence in some states in order

Jan 1, 1997

By Andrew L. Mular

Methodology to model, simulate and optimize full scale mineral pro- cessing circuits in production environments is reviewed and evaluated. Strategies for data acquisition and adjustment are considered along with techniques to fit models to adjusted data. Examples are considered for clarity.

Jan 1, 1989

By Paul C. Schmall, John F. Donohoe, Arthur B. Corwin

In the aftermath of the September 11th attack on the World Trade Center, groundwater control was of immediate concern. Water in?ow from the adjacent Hudson River through the compromised slurry wall ‘bathtub’ surrounding the site, ruptured water and sewer mains, and saturation from fire hoses all contributed to an already critical situation, further hampering the recovery and rehabilitation effort. An extensive pumping and deep well installation program was initiated, focused on reducing the hydrostatic loading to the severely damaged perimeter slurry wall.

Jan 1, 2003

By D. Nilsson

This paper demonstrates the importance of including a discount rate in the determination of the optimum final' depth of an open pit. Without a proper discount rate, a pit will probably end up too deep. Another consideration is future underground mining. If underground mining is profitable, the pit may need to be shallower. Of all of the investments needed, only mining equipment and the underground mine should be included, and amortization and depreciation should not he included in the study.

Jan 1, 1997

By K. Severin, B. Flanigan, P. Marion

"Plutonic-related" gold deposits in Interior and SW Alaska (Tintina Gold Belt) vary significantly in size, grade, vein/deposit morphology, depth of emplacement, distance from causative pluton and metal association. Metal associations such as Au-Bi and Au-As- (Sb-Hg) are a good empirical indicator of the depth of emplacement and distance from causative pluton. These associations have been used successfully in exploration. Results from several analytical techniques also suggest a phenomenological cause for these metal associations. Gold and bismuth have paired mineralogy at high temperatures and, thus, are best correlated at deposits that are deep and/or close to causative intrusions.

Jan 1, 2003

By Michael J. Friedel

As part of a study aimed at understanding the hydrology of in situ leach mining (ISLM), the Bureau of Mines, in cooperation with the Cyprus Casa Grande Corporation and the University of Arizona, is investigating dynamic transmissivity conditions during ISLM of a copper oxide ore deposit. Spatial and temporal variations in ore zone transmissivity during two years of ISLM operations at the Cyprus Casa Grande mine are evaluated during sixteen intervals of steady-state injection and recovery well operation. Direct inversion of an analytical hydrologic model is used to obtain estimates of transmissivity at 58 well locations during these intervals. Univariate statistical and geostatistical methods are used to describe the temporal and/or spatial relationships that exist between transmissivity and other ISLM parameters, including average well injection pressure, average sulfuric acid concentration in leach solution, and the relative configuration of injection and recovery wells. Average transmissivity during the sixteen steady-state time intervals varies between 6.00 x 10-6 m2/min. (6.46 x 10-5 ft2/min.) and 3.61 x 10-8 m2/ min. (3.89 x 10-7 ft2/min.). A trend toward decreas¬ing transmissivity is evident during two year of ISLM operations. This decreasing trend is found to correlate with a decreasing sulfuric acid concentration in injected leach solution, and suggests increasing geochemical precipitation within the deposit. Geostatistical analyses reveal a dynamic and anisotropic transmissivity structure within the target ore zone, that is dependent upon spatial and temporal changes in injection pressure and well configuration.

Jan 1, 1992