Search Documents

By Steven J. Schatzel, Kayode M. Ajayi, Zoheir Khademian

The integrity of unconventional shale gas well casings positioned in the abutment pillar of a longwall mine could be jeopardized by longwall-induced deformations. Under such scenarios, the surrounding fracture networks could provide pathways for gas flow into the mine creating safety concerns. To provide recommendations for developing guidelines that ensure a safe co-existence of longwall mining and unconventional shale gas production, this study evaluates the impact of parameters that could affect potential shale gas flow into the mine in the event of a casing breach using a discrete fracture network (DFN) model. These parameters are evaluated using a conceptualized DFN realization that is representative of the fractured zone in the overburden, and the range of parameter variations is within values validated with field measurements. The results show that a decrease in fracture aperture (potentially due to longwall-induced stress in the likely vicinity of the breach location) reduces the potential gas flow to the mine by a significantly higher proportion. A 50% decrease in the aperture of the fracture that directly transports the gas from the casing breach location reduces the gas flow to the mine by over 70%. Similarly, changes in the fracture water saturation level significantly affect the gas flow. In all cases, the potential gas flow to the mine is higher if the casing breach occurs at an increased gas well pressure. These findings provide critical information regarding the impact of each of the parameters associated with gas flow in the event of a shale gas casing breach near a longwall mine and could help towards the development of guidelines to ensure a safe coexistence of both industries.

Sep 28, 2022

By G. J. Joy, J. P. Rider

"Technical advances in longwall mining over the last several years have resulted in much larger and faster shearers that have the capability of mining at speeds over 100 ft./min. This has resulted in a substantial increase in the amount of dust that is generated at the shearer and during shield advances. Meanwhile, increased underground coal production has put a greater demand on longwall dust control systems as some operators have had difficulty maintaining consistent compliance with federal dust standards. To address this need, the National Institute for Occupational Safety and Health [NIOSH] is investigating the effectiveness of a water spray manifold mounted on the tailgate end of the shearer body. The sprays are oriented parallel to the tailgate ranging arm, and these sprays create a water curtain confining the dust plume near the face, preventing the dust from drifting into the walkway. This redirection of dust provides a clean air envelope for the tailgate shearer operator and jacksetters working near the tailgate drum. Three different tailgate spray manifold designs were tested and evaluated at the Office of Mine Safety and Health Research [OMSHR] Pittsburgh Longwall Test Facility. Manifolds were equipped with hollow cone or flat fan water spray nozzles and evaluated at three face air velocities (500, 700, and 900 fpm) and at water pressures of 100, 150, and 200 psi. Reductions in dust concentrations were observed at six face sampling locations for all the tailgate manifold systems at each of the tested spray pressures and face velocities. Based on results from the laboratory tests showing reductions in dust concentrations at sampling locations downwind of the shearer a spray manifold was fabricated and evaluated at an underground operation. INTRODUCTION In 2012, underground coal mining in the United States produced a total of 342 million short tons, with longwall mining accounting for over 53% of this production [EIA 2013]. The longwall mining industry continues to see remarkable and significant improvements in longwall mining equipment and mining practices. Average shift production during compliance dust sampling has increased from 3,500 tons per shift in 1994 to approximately 6,000 tons per shift in 2012. A dramatic decrease in working longwall faces from 80 to 49 has occurred over the same period [Fiscor 2013]. Factors specific to longwall mines that supported productivity improvement include: higher capacity shearers, improved shield hydraulics and control, higher horsepower for equipment, wider face conveyors, and larger faces. Today, the average face width has increased to 1,188 ft., with one longwall operation reporting a face width of 1,650 ft. compared to an average of 750 ft. in 1994 [Fiscor 2009, 2014]. Panel lengths in 2013 averaged 11,307 ft. compared to 7,000 ft. in 1994. Overall production from U.S. longwalls has increased by nearly four percent from 2007 to 2012 with over 182 million tons mined annually [EIA 2013]. Given the volume and rate of coal produced on longwall faces, the potential to generate large quantities of respirable coal mine dust also exists."

Jan 1, 2015

By M. Hakan Morcali, Onuralp Yücel, Haldun Gürcan, Serdar Aktas, Semih Özbey, Alper Keskin

"This work presents a method for the precipitation of cobalt sulfate by alcohols, specifically ethanol and methanol. The effect of the initial concentration of cobalt, the volumetric ratio of alcohol to cobalt sulfate solution, the addition of sulfuric acid and ammonia, and the effects of common ions on the precipitation percentage were investigated. The performances of ethanol and methanol were compared in terms of the precipitation percentage of cobalt sulfate, and explanations for different performances are offered. In the sulfate-based solution, the alcohol was shown to displace water ligands from the first coordination sphere of the cobalt(II) cations, which led to the precipitation of the cobalt ions as cobalt sulfate heptahydrate. SEM analysis revealed that the particle sizes of the powders produced by this method are smaller than those of commercially available cobalt sulfate. The scientific literature contains no data on the solubility of cobalt sulfate in ethanol. In this study, the solubility product constant (Ksp) for cobalt sulfate was experimentally calculated to be approximately 1.15 x 10-5.IntroductionCobalt sulfate, which is one of the most important compounds of cobalt, is used in the electroplating and electrochemical industries. The addition of cobalt sulfate to nickel-plating baths makes the treated metals brighter, harder, smoother and more ductile (Armstrong et al., 1988). It is also used as a desiccant for lithographic inks, varnishes, paints and linoleum, as well as in storage batteries, e.g., nickel-cadmium (Ni-Cd) and lithium-ion (Li-ion) rechargeable batteries (Kang et al., 2010). Cobalt sulfate is employed as a coloring agent in ceramics, enamels and glazes to prevent discoloration and as a copigment for the decoration of porcelain. In addition, cobalt sulfate has been used in animal feeds as a mineral supplement (Budavari et al., 1996; Kirk and Othmer, 1999).In the past, brewers used cobalt sulfate to prolong the life of beer foam (Kesteloot et al., 1968). Ranchers have dosed livestock with cobalt sulfate or used fertilizer enriched with this mineral to ensure that their animals obtained sufficient amounts of the trace mineral, which is essential to the production of vitamin B12. Cobalt sulfate has also been used in veterinary medication to prevent and treat cobalt deficiency in ruminants, which causes a reduction in feed intake and body weight, accompanied by emaciation, anemia and debility.Cobalt sulfate is a water-soluble bivalent cobalt salt. Cobalt sulfate heptahydrate dehydrates entirely at 420° C, and the dehydrated salt forms red monoclinic crystals."

Jan 1, 2015

By Robert Stefanko

Longwall mining appears very attractive from an engineering standpoint because of its simplicity. The use of one long, continuous face can simplify power distribution, ventilation, and supervision, and minimizes or prevents lost time associated with the tramming of equipment in room-and-pillar systems. Since the longwall system is more amenable to automation, it is inherently safer than room and pillar. Remote control of all face equipment from gate roads will obviate the exposure of men in the face area. Considering what has been said, it seems a paradox that more longwall installations are not found in the United States. However, with favorable mining conditions in relatively level seams of adequate height under shallow cover, it has been possible to develop highly productive, mechanized, room-and-pillar systems. Thus there has been no real incentive to employ longwall in the United States. In Europe, mining companies usually have very little choice between the two systems. Pitching seams of low height located at great depth dictate the use of longwall methods. With depletion of its readily accessible reserves, mining conditions will be similar to those now prevailing in Europe, and an increase in the use of longwall in the United States can be anticipated.

Jan 1, 1963

By David R. Delling

Tenneco is a large, diversified, energy-based company which has grown rapidly during its forty year life. We're the youngest corporation among Fortune's top 20 companies. Tenneco Minerals Company is the division of the Corporation responsible for nonfuel minerals exploration, development and operations. Tenneco Minerals Company is headquartered in Lakewood, Colorado. Exploration offices are in Colorado, Nevada, Alaska, and Perth, Australia. We currently operate two gold mines in Nevada and a large underground trona mine and soda ash processing plant in Wyoming. The latter has a capacity of 907 000 tonnes per year of soda ash and is the subject of my presentation today.

Jan 1, 1984

By James T. Finley

Profit, product quality, speed of operations, reliability, operator confidence, safety and environmental improvements have all been enhanced as a result of the recently completed maintenance, renovation and construction program at Crown Central Petroleum Corporation?s (Crown?s) coke calcining unit at its Pasadena, Texas refinery. (Figure 1) BACKGROUND The calcining unit was built in 1969 - 1970 and has been operated continuously. Approximately 400 to 500 TPD of high quality metallurgical grade coke is manufactured, stored, and shipped to consumers. About 1/2 of the feed stock to the calciner is manufactured in Crown's coking unit and the remainder is received, via barges, from various sources. The green coke is off loaded from the barges with a conventional grab crane that discharges into a small travelling hopper over a conveyor belt that feeds a radial stacker, which forms a stockpile on the ground. The green coke, from the coking unit at the refinery, is moved to the calcining unit with front end loaders. Reclaiming from the stockpiles is also done with front end loaders. The coke is primarily handled by covered conveyor belts. The finished product is stored in steel silos and can be shipped via railroad cars, but the majority of it is shipped out in ocean going bulk carriers. Maintenance work in the calcining unit is performed by Crown's refinery maintenance department on an as needed, on call basis.

Jan 1, 1983

By Roland W. Rammler

In recent years, the crude oil reserves of the world have increased at the same rate as the consumption. A Consideration of the global figures suggests that adequate supplies of petroleum will be available during the next decades. On the other hand, it in a fast of economic and political significance that the reserves in the industrialized countries increase much more slowly than in the developing countries. In Western Europe the reserves have even decreased. At the present time, about 70 % of the petroleum reserves of the world are in the Middle East and in Africa in regions in which political arises are prevalent or impending. For the industrialized countries, the discrepancies between the consumption and reserves in various regions of the world are a strong urge to investigate whether oil can be recovered from other sources. The situation will probably not be changed to a large extent by the discovery of oil in the north of Alaska. The main starting materials for the production of synthetic crude oil are coal, oil shale and tar sand. In North America, where the consumption of petroleum increases more rapidly than the reserves, there are enormous deposits of each of the three materials. This fact is another incentive toward the utilization of these unconventional oil reserves, which provide a reliable basis for a supple of energy for a long time to come.

Jan 1, 1970

By J. Y. Hwang

Alunite has been utilized as raw materials for producing alumina and potassium sulfate fertilizer in Russia for many years. In the United States, this mineral has not been commercially processed though reserves of 5 to 10 billion tons of alunite ore have been estimated. Major constituents of these ores include quartz and alunite. The minerals are finely intergrown and liberation occurs below 10 microns. Adequate separation techniques for such fine particles have not been developed. A new method for the beneficiation of alunite ore is proposed in this study. 'Ibis method utilizes a small amount of fine magnetite upon which the liberated quartz is selectively flocculated. The co-flocculated magnetite and quartz are then separated from the alunite in a high gradient magnetic separator. Clean products, e.g. an alunite concentrate of 90% grade with 80% recovery, has been obtained from an Utah ore. Techniques for the selective co-flocculation of magnetite and quartz, the separation of the carried quartz, and the recovery of magnetite after separation are discussed.

Jan 1, 1985

By Gerhard Lang

"Slurry Microtunneling is a well-established technology building on over 20 years of experience in successful tunnel installations under all kinds of soil conditions across the U.S. and Canada. Recent microtunnel installations prove that initial hesitation, e.g. curved drives, is fading and long-distance pipe jacking projects as well as lake outfalls are being considered. One of the younger technologies is Direct Pipe®, which combines the benefits of HDD and Slurry Microtunneling. It fits exactly into the area where HDD is not feasible or too risky to apply. The paper points out the benefits of the Direct Pipe® technology for owners, engineers and contractors and discusses the latest developments of Slurry Microtunneling for long-distance, curved drives and sea/lake outfalls with wet recovery of the equipment such as on the ‘Keswick Outfall Project’ in Ontario. The first Direct Pipe® installation in the US was executed in August 2010. Since then, another 22 crossings have been carried out amongst a total of more than 60 Direct Pipe® crossings worldwide. INTRODUCTION Pipelines installed underground are indispensable for supplying the growing world population with water, oil, gas and electricity, for removing wastewater and for providing functioning telephone and communications networks. During recent years the limits of trenchless applications have been permanently shifted, leading to higher and more stringent project requirements and consequently new technologies, either as further development of existing methods, or through the development of new methods by incorporating elements of proven technologies. MICROTUNNELING TRENDS IN NORTH AMERICA Slurry Microtunneling has a wider geological application range in comparison to EPB and hard rock Microtunneling. The Slurry MTBM can be equipped with specific cutting wheels to cope with different soil conditions. The most flexible and most often employed type is the mixed soil cutting wheel, which contains a mixture of disc cutters as well as scrapers for varying soil conditions from cohesive soils (clay, silts) to highly permeable soils including sands, gravels and cobbles and even hard ground formations such as rock and boulders. A detailed geotechnical report provides the appropriate data to configure the MTBM and its features to the ground conditions expected. Mixshield or hydroshield (AVN/AVND) MTBMs in particular, can be safely operated with little overburden (~ 3-5 x machine diameter) and minimum risk of frac-out or settlement on the surface. This is especially beneficial in urban areas with sensitive buildings or for river crossings with protected fish habitats."

Jan 1, 2016

By E. O. Mixon, Jack D. Kennedy

INTRODUCTION This contract is the most northerly portion of the Metropolitan Sanitary District of Greater Chicago's Tunnel and Reservoir Plan. (TARP) The project begins at Addison Street in Chicago and proceeds northerly approximately ten miles to end at Wilmette Harbor and Lake Michigan. The project which consists of 2 work shafts, 32 drop shafts, 7.322 km (24,020 ft.) of 6.7 m (22 ft.) diameter circular rock tunnel, 8.458 km (27,750 ft.) of 9.2 m (30 ft.) diameter circular rock tunnel and miscellaneous rock bolting and grouting, was bid for a total cost of $63,140,480. The tunnel invert elevation varies from 65.5 m (215 ft.) to 77.4 m (254 ft.) below the ground surface, which places the tunnel in a rock formation of dolomite limestone. At the tunnel invert, the unconfined compressive strength of the limestone varies from 96 MPa (14,000 psi) to 152 MPa (22,000 psi). The 6.7 (22 ft.) diameter tunnel required the mining of 10.9 cu m. (14.2 cu yd.) of rock per lineal foot of tunnel while the 9.2 m (30 ft.) diameter tunnel required the mining of 20.1 cu m (26.3 cu yd.) of rock per lineal foot of tunnel. The total cubic meters of rock required to be excavated from both tunnels was 818,821 cu m (1,070,978 cu yd.). All of this will be mined by tunnel boring machines (TBM). These tunnels were not to be lined with concrete. The thirty two drop shafts have upper portions that are cylindrical in the overburden and rock sections. They were divided into two groups, depending on diameter, with a different construction method for each group. The first group consisted of twenty three of the

Jan 1, 1979

By James H. Barks

Exploration for ore deposits in southeastern Missouri in the 1950's resulted in the important discovery of lead, zinc, copper and silver in 1955. Further discoveries in the area led to the naming of the Viburnum trend. It has sometimes been referred to as the "New Lead belt" to distinguish it from older lead-producing areas to the east. As presently developed, the "trend" is 35 miles long, running north and south about 50 miles west of the Lead belt. Galena (lead) is the principal ore mined, with lesser quantities of sphalerite (zinc), chalcopyrite (copper) and silver recovered as economic by-products. The ore body is as much as 140 feet thick and 1,200 feet wide, and is found in the Bonneterre Dolomite (Upper Cambrian) at depths ranging from 700 to 1,200 feet. Since its discovery many companies have engaged in exploration and several major companies have developed new mines and constructed mills and a smelter in the area. The first mine in the Viburnum trend came on stream in 1960, but as more mines came on stream and others reached capacity, lead production increased to the point that the Southeast Missouri Lead district produced 432,576 tons of lead in 1970 to become the world's largest lead-producing region (Missouri Geological Survey and Water Resources, 1971). The Viburnum trend area with its rolling, heavily forested hills and numerous clear running streams is in the Clark National Forest of the Missouri Ozarks. Until the recent development of its mineral resources, the area was sparsely populated and nearly unmarked by the activities of man. Industrial development is almost certain to be accompanied by environmental changes. In a day of growing awareness of the need to preserve the quality of the

Jan 1, 1971

By J. C. Cawley, G. T. Homce

The U.S. National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) conducted a study of mining industry electrical injuries reported to the U.S. Mine Safety and Health Administration (MSHA) for the years 2000 to 2009. The findings of that study are detailed in this paper, and serve to characterize the circumstances surrounding electrical injuries and identify causal factors. The study included three tasks: 1) a direct review of mining industry occupational injury data compiled by MSHA, 2) interpretation of the narrative descriptions available for the injuries (from MSHA data) and 3) a separate examination of fatal electrical injuries. Eight-hundred sixty-five electrical injuries were reported during the 10-year period studied, with 39 of those being fatalities. This makes electrical injuries disproportionately fatal with respect to most other types of injuries in mining. Electrical injury rates were higher in coal mining than noncoal mining and, within the coal sector, rates were higher in underground operations than in surface operations. Of the 865 total cases, electrical and machine maintenance or repair activities were involved in 580 (69%), and electricians and mechanics were injured in 362 cases (42%). Of the 39 fatal electrical injuries, 27 (69%) involved electrical maintenance or repair work, and in 21 of these 27 cases, the failure to de-energize, lock-out and tag the circuit was the cause or a contributing factor. Also, contractor employees had a much greater chance of an electrical injury being fatal than did mine operator employees. The top three root causes for fatal electrical injuries were 1) no or inadequate lock-out and tagging, 2) failure of power system components and 3) contact of overhead electrical power lines by mobile equipment.

Jan 1, 2013

By M. Werner

Mining in the Coeur d'Alene Mining District has been going on for over 100 years with a long- term continuation very likely. Mining is presently carried out at depths below the -5000' horizon. As mining continues at ever increasing depths, higher in-situ rock stresses and subsequent rock deformation is encountered making mining costly and hazardous. To provide access for men and materials in such areas, a wooden raise preparation structure is typically built. Although these structures provide adequate support and access, they have proved to be very costly to construct and maintain.

Jan 1, 1986

By Wesley W. Eckles

Microcomputer technology has begun to revolutionize petroleum engineering. Petroleum engineers' use of relatively inexpensive personal computers (PC's) is likely to continue expanding rapidly. Since 1982 SPE's Microcomputer Applications Committee has developed a Society-wide users group, a bi-monthly newsletter (MICROCOMP NEWS), an SPE Short Course, a hardware and software distribution program, and a world wide electronic network (SPE NET). The purpose of this paper is to share SPE's experience in creating a dynamic program for meeting the individual member's need in the application of microcomputers to petroleum engineering. My hope is that this will encourage other engineering and scientific organizations to provide similar programs for their members.

Jan 1, 1985

By O. Tranbarger

In aging tunnels, wall and roof deterioration can eventually result in defects that must be detected and repaired to maintain safe structural conditions. In investigating tunnel defect conditions, a specialized FM radar system was developed with a programmable VHF and UHF operating sweep range for optimizing the penetration and measurement capabilities. The new FM radar technology was tested in two aging brick-lined tunnels in New York City. Test results showed that FM radar signals could penetrate eight courses of water-saturated brick and that the original steel liner outside the tunnel walls was intact.

Jan 1, 1985

By R. L. Pearson

The 1987-88 Denver Brown Cloud Study was performed to determine the sources of the particle cloud which forms over Denver each winter. The study was organized under the leadership of Colorado Governor Roy Romer , EPA Region VIII and the Greater Denver Chamber of Commerce. The study was sponsored by over 40 organizations representing governmental agencies, the natural gas industry, the coal industry, utilities, oil companies, railroads, the motor vehicle industry, and other Denver area companies and organizations. The cost of the study was $1.5 million which was raised almost entirely from private sources. The study team was headed by Dr. John Watson of the Desert Research Institute of the University of Nevada. Dr. Watson is a recognized expert in conducting studies of this type.

Jan 1, 1990

By Donald R. East

There has been an increasing trend in recent months by regulatory agencies to require that estimates be made of the hydraulic head acting, under operational conditions, on the surface of primary leach pad liners. This move towards inferred performance standards, rather than specifying a prescriptive standard for all sites regardless of economics, is to be generally welcomed. The theory of flow on a sloped beach pad, which was developed by East et al, 1987 (Reference 1 and 3) has been refined and extended. Unitized curves have been developed by graphically displaying the seepage losses and resulting dissolved gold lost as seepage through the primary liner as an aid to pad liner selection and design. Very little information is available of actual hydraulic head profiles acting on the liners beneath heap leached ores. Attempts have been made to measure these by drilling from the top of the heap and installing piezometers at the base. With this procedure it is difficult to obtain accurate data due to the fact that the drilling operation itself creates a highly permeable vertical flow path which may not exist to the same degree elsewhere in the heap. Combined with the fact that it is almost impossible to ensure that the piezometer tip is sitting directly above the liner without the risk of causing some damage to the liner itself. The best time to install hydraulic head monitoring devices on the pad liner is during construction and when piezometers can be carefully placed directly above the liner and suitably protected hydraulic lines laid to ensure full hydrostatic head measurement with simple manometer devices.

Jan 1, 1998

By M. S. Davis

The Tek Process can produce masonry products such as bricks, roof or wall tiles, and block from virtually any inorganic waste. In the process the aggregate raw materials, portland cement, water and common chemicals are first mixed together; then mechanically subjected to several thousand pound pressure per square inch. This causes a novel chemical reaction between the cement, chemicals and water; producing the "patented" Tek adhesive binder which holds the aggregate together in a stone-like mix. Simultaneously, the desired product shape is formed. The building modules can have strengths of 8000 p.s.i. (pounds per square inch) with completely sound aggregates utilizing air curing for a period of 28 days. With most aggregates, 3000 p.s.i. is achieved within 24 hours. Eventual strengths usually exceed 5000 p.s.i. with almost any raw material. Water absorption ranges from 5-7.5 percent. Both absorption and strength figures are superior to the most rigid of any and all A.S.T.M. specifications for the highest quality bricks. In most locations, the product (when brick shaped is called Tekbrik) can be produced significantly more economically than can comparable grades of clay or other bricks, be- cause almost any inorganic waste materials or pollutant can be used as a raw material. The process results in a lower manufacturing cost as compared to clay bricks; fuel cost to operate a clay kiln represents a substantial portion of the total cost. Capital expenditure for a Tek plant also is lower due to the large investment in clay kilns. Transportation savings also are important, clay brick factories must be very large because the kilns are uneconomical unless they are large. Most bricks are manufactured at the sites of clay deposits in relatively uninhabited areas. The cost of transportation to the job site represents a considerable percentage of the selling price.

Jan 1, 1974

? World industrialization, increased urbanization, and population growth are driving a sustained demand for minerals, metals and coal. Energy demand is expected to increase significantly in the coming decades - placing even more emphasis on supply, security and environmental impact issues. ? Several countries are taking steps to nationalize their own resources thus safeguarding their supplies and reducing exports of natural resources. ? Understanding the future availability of critical minerals requires a global perspective. It is essential to know where deposits are located, their reserves and resources, the technologies necessary for production, and the costs of producing and transporting the products to consumers. ? As mining companies look to maintain or increase their operating capabilities and increase their mineral resource bases, the search for commodities expands beyond developed terrestrial regions of the world, to include marine resources. (Figure 1) Operating challenges in these locations include finding skilled workers, building infrastructure, improving recovery technologies and practicing sustainable development.

Jan 1, 2011

By Willard C. Lacy

Survival of the mining industry as a viable economic entity in the United States is being seriously threatened by declining grades of ore reserves, rising operational and capital costs, and increased governmental taxes, restrictions, and subsidizing of third world competition. Discovery of major high-grade deposits is becoming increasingly unlikely. International competitiveness of the U.S. deposits will depend upon 'Yankee Ingenuity', innovations in mining methods, metallurgical treatment, and financial arrangements, and a viable national strategy. This will require not only effective management for control of operations, but management that encourages breakthroughs in technology, financing, labor relations, and in public and governmental understanding. The mine geologist and the exploration geologist both have important roles to play in all aspects of this fight for survival of the industry.

Jan 1, 1984