Search Documents

By P. C. Schutte, A. J. Kielblock

INTRODUCTION Certain activities, such as emergency work and rescue operations, often have to be undertaken in environments where heat loads often exceed limits prescribed for routine work. This is particularly relevant to the South African mining industry where heat stress-induced fatalities are not uncommon during rescue operations. In this regard an excessively hot environment is defined as one where either the dry-bulb temperature exceeds 37,0°C or the wet-bulb temperature exceeds 32,5"C, and it is therefore not surprising that heat stroke mortality escalates rapidly when these limits are exceeded. A review of both local and international standards indicated that the available information on safe exposure times under abnormal heat stress conditions is very limited. Where available, such standards are aimed at the general population, including both sexes, irrespective of age and also the least heat tolerant worker, and not at a medically-screened, all-male population free of grossly heat intolerant individuals, as is the case in the South African mining industry. It is suggested that available norms and limits are too conservative for local application and, therefore, unrealistic. In view of the definite need to protect workers when exposed to abnormally high environmental temperatures, the present study was undertaken to establish a scientifically derived data base. applicable to local conditions, to determine safe exposure times: Any exposure limit, especially in an emergency situation, should be easy to administer, valid and reliable. These aspects, there- fore, form an integral part of this paper. FORMULATION OF HEAT STRESS LIMITS The formulation of heat stress limits was based on the criterion that a heat exposed individual should experience a negligible risk of developing dangerously elevated body temperatures. In order to provide a database for risk assessment, certain physiological responses of heat tolerant men were determined at various combinations of thermal conditions and work rate in a climatic chamber. These physiological responses were analysed statistically in order to predict safe survival and tolerance times as a function of thermal conditions and work rate. EXPERIMENTAL DESIGN A total of 202 randomly selected, medically fit mine workers volunteered for the study on the basis of informed consent. These men were considered to be inherently heat tolerant in as far as they had successfully completed a heat tolerance test (Anon., 1991) or the standard climatic room acclimatisation procedure used on many South African gold mines (Anon., 1989). The subjects were allocated randomly to 14 experimental groups and each group was exposed in a climatic room to one of

Jan 1, 1997

By Gavin Erickson, Lucas R. Moore, Clint Stoddard, Garret Bryant

As global mineral feed grades decline, phosphate beneficiation faces mounting challenges. Chief among these being achieving high recoveries of industry quality concentrates from ores of decreasing quality. Apatite, a critical mineral for meeting global fertilizer demand, remains the primary source of phosphorus and is typically recovered through beneficiation by multi-stage flotation. However, traditional saponified fatty acid collectors lack the selectivity needed to beneficiate these lower quality ores, which are containing a higher concentration of more complex gangue minerals. Enhancing collector performance is essential to the industry moving forward. This study introduces a novel alkyl polyglucoside based surfactant designed as an additive for conventional fatty acid systems. Its incorporation significantly improves the grade recovery in direct apatite flotation, even at low concentrations. Flotation results as well as surfactant properties will be discussed.

Feb 22, 2026

By Paul D. Tomlingson

A new sense of urgency permeates the mining industry concerning maintenance. Mining's continuous process environment demands around-the-clock maintenance support. And profitability conscious mining operations require that production targets be met on time - and economically. These goals require nothing less than an effective maintenance program. In turn, the effectiveness of the maintenance program depends on quality information: easily procured, complete, timely, accurate, and properly used. Information picture is changing Some of the fully integrated, mainframe maintenance information pro¬grams of better days remain. Their upkeep and cost of operation, though, is becoming more difficult to justify. Some operations, faced with production cutbacks a few years ago, downscaled and found they liked it. Now, during an upswing, these operations question the need for the more elaborate, administrative-heavy programs they used to operate. Package programs are not taking their place. Too often, the packages are vague and generic. Some vendors claim that if their offerings work in a hospital complex, they must work in an underground mine. That is not so. Maintenance information in the mining industry is different. The situation has changed There are now smaller, self-contained maintenance groups whose information needs are different. These include an electrical crew in a smelter, an underground mobile equipment shop, or a remote service shop between several distant operating pits. These working environments have changed the character of the information needed as well as the methods for obtaining and using it. Operations-maintenance link In coming back from a downturn, operations people realize that their ability to meet production targets hinges on reliable equipment and avoidance of downtime. They have become familiar with the need to use maintenance services effectively. They also want quality maintenance information. When coupled with the sense of urgency about maintenance, a business-like working environment emerges that has significant new differences in both work control and information. Work control impact Work control has been streamlined to improve communications. Supporting information has been streamlined as well. • Verbal orders are the rule rather than the exception to quickly bring a multi-craft crew to the flotation section or a pit crew to a disabled haulage truck. • Written work requests and work order forms are seldom used, or even needed. Rather, electronic work control logs permit operations to request work, maintenance to acknowledge it, get ready, and do it - quickly, without delay. • Routine servicing is triggered by operating hour accumulation (mobile equipment) or tons of throughput (fixed equipment). Operations is now taking the initiative in delivering mobile equip¬ment to the "bad order line," or switching to a bypass conveyor. Operations wants immediate follow-up reports on equipment condition.

Jan 1, 1989

By James T. Curry

The steady growth of the Northwest portion of the United States over the past two decades, and the very rapid development of Northern California, Western Nevada, and Oregon in particular, led the Calaveras Cement Company people to Shasta County, California in 1957. The presence of a large deposit of high calcium carbonate limestone had been recognized for many years, but it required the momentum of an expanding economy to make these long known reserves valuable. This, plus the availability of a reliable supply of fuel in the form of natural gas, and the ready means of shipping the product to the consumer both by highway and railroad, seemed to offer the proper combination to launch a successful venture. The Calaveras Cement Company had been manufacturing cement by the wet process since 1925 at their plant at San Andreas, California. Starting with two small kilns, the plant in Calaveras County started an expansion program in 1945 that ultimately resulted in the plant as it exists today, consisting of five kilns with a combined production of 4.5 million barrels annually.

Jan 1, 1967

By Brajendra Mishra, Himanshu Tanvar

Niobium and tantalum extraction industries heavily depend on fluoride chemistry for metal oxide production. This study concentrates on developing a fluoride-free approach utilizing alkali treatment for selective dissolution of niobium and tantalum phases. The application of microwave heating in the alkali treatment of columbite significantly reduced the processing time, providing a higher reaction rate and recovery than conventional heating. A short duration of microwave exposure (6 min) elevated the sample temperature to more than 900 °C, resulting in the rapid formation of water-soluble niobium and tantalum complex. Metal recovery from the solution was attempted through direct precipitation using guanidine carbonate as the precipitating agent, resulting in a mixed oxide product with > 90% purity. On the other hand, solvent extraction was also attempted using methyltrioctylammonium chloride as an extractant, providing a niobium oxide and tantalum-rich mixed oxide with > 98% purity as the final product.

Mar 23, 2024

By J. S. Lee

Alkyl hydroxamates are well known collectors for oxide copper minerals as evidenced by the large amount of published literature. Our studies on a wide variety of copper ores from around the world have shown that alkyl hydroxamates will recover most of the "floatable" oxide copper minerals from an ore. They are available commercially, and they offer many advantages over alternative technologies for oxide copper recovery. In spite of this, the full potential of hydroxamates has not been exploited in the industry. The objective of this paper is to provide relevant practical aspects and guidelines to facilitate successful application of hydroxamates in operating plants. A critical analysis of the available information and data, based on several case studies, notation testing, and microscopic analysis indicates that alkyl hydroxamates can effectively recover well-defined oxide minerals of copper, but not copper occurrences such as Cu-bearing goethite (often misidentified as cuprite) which report as Acid Soluble copper in chemical assays. Prior to any notation testing with hydroxamates, it is necessary to assess the various modes of occurrence of Acid Soluble copper using microscopic and microprobe analysis.

Jan 1, 1998

By C. Alan Tapp

Introduction Mine sampling determines the practicality of any mining operation. Improper sampling can result in an incorrect appraisal of present production and future potential. Therefore, the mine department in charge of ore-reserve calculations and mine sampling should be overseen by competent and experienced professionals with technical backgrounds qualifying them to produce accurate results. Sampling is a process by which portions of an ore body are collected and analyzed to estimate the average mineral content of the entire ore body. It is incorrect to assume that a large number of samples eliminates any errors in the sampling method. To obtain unbiased samples, proper sample location with respect to rock type and mineralization is just as important. The sampling procedure must yield correct results for the type of mineral deposit, and careful consideration should be given to whether or not the sampling technique has been developed to an extent sufficient to eliminate as much human error and bias as possible. Only after the ore has been mined and milled is the sampling accuracy known. Sampling also provides information about the bulk composition of the ore for mineralogical and metallurgical tests that determine the economic ore-waste boundaries and the geologic trends for exploration. Actual mining plans can be developed from this information to maximize profits. Accurate sampling is critical, and thus must be approached in a scientific manner. Sampling Techniques Sampling practices and techniques are as varied as the mines in which they are used. The method(s) chosen must be tailored to suit the company and mining needs. For instance, tabular uranium deposits, vein gold deposits, and porphyry copper deposits pose special problems in conducting unbiased sampling. The mine geologist or engineer in charge must develop a sampling method, test it in a sample area, and then critically evaluate the results. If the results from the test area are accurate within the economic limits established by the company, they then may be adopted for general use in the mine. Four routine sampling methods are suitable for specific sampling objectives in the daily mine routine: (1) channel sampling, (2) chip sampling, (3) grab sampling, and (4) bulk sampling. The final sampling results depend upon how the four methods are combined to accurately determine the grade of the ore body. When used in conjunction with each other during different stages of mine development, the channel, chip, grab, and bulk sampling methods provide an in-house check or a comparison by which mining methods and sampling procedures can be evaluated. However, the most valid check is based upon the daily mill production. Channel Sampling Channel samples consist of cuttings collected from a groove cut into the rock about 102 mm (4 in.) wide and 19 mm (0.75 in.) deep. Various tools ranging from a 1.8-kg (4-lb) hammer and moil to a pneumatic chisel can be used to cut the sample. Accessibility and rock hardness determine the applicable sampling tools. Before attempting to take a sample, the rock surface must be cleaned thoroughly; the method of cleaning depends upon the amount of mine dust accumulated on the surface or the degree of alteration of the rock surface. Typical cleaning methods 'employ a wire brush, water, or chipping a fresh surface. Next, the sample outline is marked on the prepared surface, taking care to choose appropriate sample loca- tions. After determining the proper sample outline and length, the sample can be chiseled out, catching the rock fragments on a canvas tarpaulin on the floor, in a powder box, in a canvas bag to avoid contamination, or by some other suitable means to capture all of the sample. Vertical veins present a special problem because the drift's back usually is arched, not square. For example, Fig. 1 shows that if sample intervals are measured from A' to D', the length of the sample interval is greater than the true vein width, resulting in an incorrect calculation of the ore reserves. The correct method would collect three samples at A'-B', B'-C', and C'-D', using either actual measurements in the mine represented by A-B, B-C, and C-D or trigonometric calculations to determine the true ore thickness. Then, each sample can be weighted by grade and true thickness for the vein. Channel lengths usually are a maximum of 1.5 m (5 ft), and it is good practice to divide longer samples into smaller intervals according to structures, changes in rock types, or differences in rock hardnesses. The influence of those features on the mineralization then can be determined. Chip Sampling Chip sampling is a variation of channel sampling used when the rock is too hard to channel sample economically or when little variation in the mineral content indicates that this sampling method will yield results similar to those of channel sampling. Rather than cutting a channel in the rock, small chips are flaked off at regular intervals over the entire face or area being the mine. sampled. Care must be taken to assure that the sample is representative of variations in the rock hardness and type. hi^ method is fast and useful in preliminary evaluations, but it should not be used for quantitative ore-reserve calculations. Grab Sampling Grab sampling is a fast method for double checking either channel or chip-sampling procedures, and, in some instances, mine production can be estimated from carefully taken grab samples. Grab sampling takes equal amounts of material at selected intervals over a mine dump, a muck pile, or from an ore car to estimate its Channel Sampling mineral content. Generally, this method is not considered reliable. Many independent variables can affect this type of sampling process. Thus, if the ore occurs in the softer fraction and a proportional amount of the result-

Jan 1, 1982

By CASSANDRA L. HOEBBEL, PATRICK L. YORIO, Emily J. Haas

This study revealed significantly less favorable perceptions of the existing organizational safety climate among workers in the underground coal-mining sector compared with those in the industrial-minerals and sand, stone and gravel (SSG) sectors. Consequently, it is important to consider pragmatic ways in which health and safety management systems (HSMS) in coal mines can alter processes to improve these perceptions. Given the interdependencies of safety climate factors and HSMS elements, researchers explored mineworker perceptions of the supportiveness of organizational safety climate factors among mineworkers and identified significant differences in perceptions across sectors. In this paper, we suggest that health and safety professionals in underground coal mining and organizations with fewer resources or less mature HSMSs focus on these factors to bolster support for proactive safety performance. Potential barriers to implementing or improving relevant HSMS elements and ideas to help foster more favorable perceptions of organizational safety climate are also discussed.

By Jorge Armstrong, Sean Warren, JOSEF BOURGEOIS

The application of statistical analysis software programs has proven useful for the investigation of rockfall runout distance along a designed slope. Rockfall modeling programs are continually being upgraded with more sophisticated analysis tools, such as the use of the rigid body versus lump mass models. Engineers at mine sites utilizing the software may have varied experience related to these models, their associated input parameters, and how to interpret the generated results. To address this concern, researchers at the Spokane Mining Research Division (SMRD) of the US National Institute for Occupational Safety and Health (NIOSH) investigated the influence of slope height, slope angle, slope material, and rock size for both rigid body and lump mass models in a 2-D statistical analysis program. Based on a literature search and industry input, specific ranges common to that of an open pit mining environment were chosen for each of the input parameters to determine 90% rock runout distance as well as their sensitivity to change. Data collected from this numerical analysis and simulation will be compared to empirical rockfall data gathered through the duration of the Highwall Safety project conducted by NIOSH from 2022–2026.

Jun 18, 2023

By E. H. Christiansen

The most valuable gem- quality red beryl comes from the Wah Wah Mountains of south-western Utah (Fig. 1). Red beryl occurs as a secondary mineral in topaz rhyolite. Marketable crystals from the Wah Wah Mountains have been produced from the Violet Mine, operated on a limited scale since 1976 under the ownership of the Harris family of Delta, UT. From 1989 to 1995, production from the mine amounted to more than $3 million with an inventory of several million dollars of unsold gems (Harris, 1995). In 1994, Kennecott Exploration leased the mine and surrounding claims to determine reserves and feasibility of gem recovery. Mining and exploration activity are continuing. Previous work on red beryl has dealt mainly with crystallographic, chemical and optical properties of the crystals (Shigley and Foord, 1984) with only general descriptions of the geology (Ream, 1979). However, the conditions needed for formation of red beryl have not been well constrained. It is generally proposed that beryl originates by precipitation in fractures and vugs from high-temperature gases as they are released from slowly cooled rhyolite lava. Dozens of topaz rhyolite flows and domes, similar in composition to the beryl-bearing flow in the Wah Wah Mountains, occur across the western United States (Christiansen et al., 1986). All of these flows devitrified to form vapor-phase topaz and locally other vapor-phase minerals such as bixbyite, garnet, hematite, pseudo-broo- kite and fluorite. But the occurrence of beryl is rare. Even within the rhyolite flow that hosts the red beryl, the productive open pits comprise only a small fraction of the surface area of the flow. Apparently, the conditions that favor the formation of red beryl are rarely achieved. Geologic setting The rhyolite flow that hosts the red beryl deposit lies along the eastern flank of the Wah Wah Mountains (Fig. 1). Prevolcanic rocks consist of Proterozoic, Paleozoic and Mesozoic sedimentary rocks that were folded and thrust to the east during the Sevier orogeny. Cenozoic volcanism began about 34 Ma. It consisted mostly of large volume dacitic ash flows and lesser volumes of low- silica rhyolite and andesitic lava flows. Beginning about 23 Ma, the style and composition of volcanism changed to smaller-volume, ash-flow and dome-forming eruptions of high-silica rhyolite and trachyandesitic lava. These rocks form the Blawn Formation of which the beryl-bearing rhyolite is one member (Best et al., 1987). Abbott et al. (1983) reported a K-Ar age of 22.1 + 0.8 Ma for this flow. It is probably the oldest topaz rhyolite flow in the Wah Wah Mountains. A subsequent episode (12 to 13 Ma) of bimodal magmatism produced the Steamboat Mountain Formation. The rhyolitic part of that is locally topaz-bearing. Displacement on the late Cenozoic extensional faults that formed the north-trending mountain ranges began about 22 Ma. Geology of the Violet Mine The rhyolite that hosts the red beryl deposit is part of a flowldome complex that overlies nonwelded tuff of cogenetic origin. This rhyolite is exposed over an area of about 9 km2 (3.5 sq miles) (Fig. 1). An unknown additional portion of the rhyolite is concealed beneath younger mafic lavas and sediments.

Jan 1, 1997

By L. E. Murr

Solution flow in leach dumps and heaps or in columns of representative rock has been the subject of only limited studies. This is a regime involving unsaturated flow in semiconsolidated rock with a wide size distribution. Even the concepts of continuous flow systems are fairly recent, and have evolved from the search for better methods of operating industrial chemical reactors. (1-3) Waste rock consolidation and permeability play a key role in solution flow characteristics. Harris (4) suggested that bulk density variations in a leach dump could alter the particle-to-particle contact, and that large particle aggregates could act like single, large particles . In the limiting case where the bulk density approaches that of the undisturbed, consolidated rock, the entire waste unit would behave as a single particle. Roman (5) treated the phenomenon of bulk density and its effect on consolidation in terms of lixiviant flow paths or solution channeling in leach dumps. Like Harris, he assumed that no solution moved through particles or particle aggregates associated with zones of high bulk density. Solution flow paths are thus effectively separated by particle regimes, creating solution channels in the waste body. While some attempts have been made to describe solution flow in leach dumps and related systems by utilizing computer model approaches and laboratory- scale simulations (5,6), there have been no direct, large-scale observations of solution movement in channels or of the actual channel sizes and distributions within a waste body. This paper describes a series of experiments involving large-scale, controlled waste leaching tests, conducted over a period of several years, and aimed at providing some direct observation of the changes in waste consolidation and permeability, the size and distribution of solution channels, the movement of such channels with continued solution application, and other features relating to solution flow during the leaching of low-grade waste. These results are then combined with mineralogical information to explain observed leach behavior.

Jan 1, 1981

Previous models describing the aggregation of polymer coated particles fail to take into account the fact that there are a limited number of sites onto which a polymer segment can adsorb, called ?active? sites. Thus, the collision efficiency is a factor not only of the fractional surface coverage, but also of the number of active sites. In this study, a physical model of the flocculation system was devised in which the number of these sites could be varied, in order to study the effect on particle aggregation.

Jan 1, 1987

By g. Caproni

The main constituent of the feed to the "Sulphide Section" (31 t/h), in the F. Sartori Plant (6000 tid) of the Miniere di Mon)eponi(Sardinia), is the ore of the Campo Pisano -Funtanaperda Mine (1 ? Difficulties have always been experienced in the treatment of this ore, owing to the extramely fine Pyrite-Sphalerite intergrowth and to the high Pyrite and soluble salts contents. The first mentioned difficulty was overcome with a rather complex flowsheet (see fig.1A and lB)(2); the others with a reagent combination that required a pH of 11 in a pulp loaded with soluble salts. This meant high consumption of alkalizer, and also of the other reagents; furthermore the alkalizer had to be mainly NaOH with only minor amounts of lime, because the latter tended to depress not only the pyrite but also the middlings, which were supposed to float. With dialchylditiophosphate alone as a collector, a lower pH could have been used, but a certain amount of amylxanthate was indispensable to promote flotation of the middlings. On the other hand, a bulk-flotation of sphalerite and pyrite at low pH could not be very advantageous on account of the high pyrite content in the feed(3).

Jan 1, 1971

By K. H. Nimerick

Froth flotation of coal is growing in importance and complexity. Some of the reasons for these changes follow. 1) A need exists for energy resource conservation. 2) Preparation plants are processing widely varying coal -- deep seam, strip and stockpiled either separately or as blends. 3) More fines are being generated because more mines are using automatic mining equipment. 4) It is more practical and economical to remove ash and sulfur at the preparation plant than during utilization.

Jan 1, 1982

By William Detty

An architect representing the Atlanta office of the Brick Institute of America periodically presents a slide lecture to interested groups entitled "The First 10,000 Years of Brick". The title signifies the fact that brick, man's oldest manufactured building material, has been around for quite some time and will continue to be utilized by architects and builders in the foreseeable future. This is not to say that the brick industry can rest on its laurels and ignore the competition presented by newer more innovative products. The industry will have to be equally inovative and market oriented in order to maintain its market share of the predicted construction boom between now and the year 2000. The implication is made, however, that brick can be produced under rudimentary conditions and that the desire to use the product has been long standing. In addition, history has sham that there has been plentiful clay available to produce the product. This paper is an attempt to assess the climate in which the brick industry will operate during the next 26 years. An analysis of regulatory conditions affecting the manufacture of the product will be followed by an assessment of the materials environment in which the industry will be operating. These factors are then reconciled with a projected demand for the product to determine the ability of the industry to satisfy future demand for brick. From a mineral point of view this paper will address itself generally to the availability of and demand for clay. However, other than a brief overview of the uses of other specific types of clay, it will concentrate on the clays utilized in the production of structural clay products, specifically brick.

Jan 1, 1974

By Ulrich Kappus

The purpose of the project is to divert flood flows of North Potato Creek. The project is located in the southeast corner of Tennessee near Copperhill, approximately 160 kilometers north of Atlanta, Georgia. The project consists of: a 28-meter high dam, a 90-centimeter diameter outlet conduit; an emergency spillway; and a 4.0-meter diameter hard rock trans-basin diversion tunnel. This floodwater management system was part of Cities Service Company mine safety program for the Cherokee orebody which is partially located within the stream channel. The following paper describes the entire project development from feasibility studies to design and construction management.

Jan 1, 1978

By Neil J. Dahmen, Howard J. Handewith

INTRODUCTION Tunneling machines were introduced into civil con¬struction in the 1800s, but their practical applications were not realized fully until the 1950s. As of 1977, tunneling machines were being used on most tunneling projects of substantial size. As in civil construction, the mining applications of tunneling machines have included long drives such as tunneling for long ore-body develop¬ment drifts, long haulage tunnels, longwall access drifts, and long crosscut developments. Tunneling machines ranging from 1.75-m (5.7-ft) to more than I1.0-m (36-ft) diam are available from several manufacturers; machines for mining applications generally have ranged between 1.75 and 6.0-m (5.7¬and 20.0-ft) diam. Tunneling machines usually operate at or near horizontal grades and are supported by a rail-haulage backup system. However, declines and inclines have been made using alternative backup equip¬ment. Either circular or shaped tunnels may be bored, depending upon the particular equipment used. Using tunneling machines to bore openings through rock offers several advantages over the use of the drilling and blasting technique. These advantages include a rapid advance, continuous operation, uniformity of the opening size, smooth walls, and safe working conditions. Compared to drilling and blasting, boring reduces the disturbance of adjacent rock, thereby reducing the ground-support requirements and the exposure to water inflows. The smooth walls provide natural arching and present minimum resistance to the flow of air. A tunneling machine should be considered a spe¬cialized mining tool that is well-suited to certain mining applications. Properly applied and sustained, a tunnel¬ing machine contributes to realizing substantial econo¬mies in the development of underground mines. All costs herein are expressed in 1977 US dollars, unless otherwise noted. The mention of trade names and manufacturers is not intended to imply an endorse¬ment of any specific equipment. TYPES OF TUNNELING MACHINES As listed in Table 1, five principal types of tunneling machines were being manufactured in 1977. Each type of machine offers a special solution to a specific mining problem. Although each of these types of machines is described herein, most of this chapter is devoted to the full-face rotary rock-tunneling machine that has demon¬strated the greatest production in both civil construction and mining applications. Full-Face Rotary Rock-Tunneling Machines As shown in Fig. 1, a full-face rotary rock-tunneling machine consists of a rotating head that is fitted with rock-cutting tools and is forced into the tunnel face. This head is supported by a bearing on a structural support member that, in turn, is held in place by a hydraulically positioned wall-gripping mechanism. Both torque and thrust are reacted from the cutterhead, through the structural support and gripper mechanism, and to the tunnel wall. The rock cuttings fall to the invert at the tunnel face, and they are removed by means of cutterhead buckets or scoops that transfer the cuttings to a conveyor belt. After advancing the cutter¬head through a preset boring stroke, the tunneling machine is advanced by hydraulically pulling the gripper mechanism in from the tunnel walls, stroking forward, and resetting the gripper to the new forward position on the wall; the machine then is set for the next advance stroke. Full-face machines cut only circular openings. Ma¬chines with diameters as small as 1.8 m (6 ft) and as large as 6.1 m (20 ft) have been used in mining applica¬tions, excavating rock with unconfined compressive strengths in excess of 276 000 kPa (40,000 psi). Although special machines have been designed to turn on a radius of 30 m (100 ft) in both horizontal and vertical directions, the conveyors and backup sup¬port equipment generally limit tunneling machines to turns with a radius of more than 60 m (200 ft). The full-face rotary rock-tunneling machines have provided the fastest and most reliable production of any mining method or machine. These machines can be equipped to place any of a variety of ground-support systems, and they can be provided as "open" machines, as shown in Fig. 1, or as "shielded" machines, as shown in Fig. 2. The open machines have the advantage of allowing the ground to be supported as near to the tunnel face as possible. The shielded machines have been designed principally to allow placing precast con¬crete segments. The shielded machines completely pro¬tect the equipment and personnel at the heading, but they are economically limited to permanent long-life haulageways where full lining is required. Partial-Face Rotary Rock-Tunneling Machines As shown in Fig. 3, the partial-face rotary tunneling machine is equipped with a cutterhead that rotates slowly at about 0.21 rad/s (2.0 rpm). The single-disk cutterhead produces the tunnel section shown in Fig. 4 by means of an oscillating motion. These machines work on the undercutting principle, and they are avail¬able in spring-line dimensional increments of 0.1 m (0.32 ft) from 1.5 to 2.1 m (5.0 to 7.0 ft); the vertical dimensions are 2.4 to 3.2 m (8.0 to 10.5 ft), respec¬tively. Depending upon the tunnel width, the cutterhead disk may be fitted with from 8 to 16 drag-bit cutters. Penetration is achieved by means of hydraulic rams that force the tungsten-carbide bits into the rock mass. The operation is cyclic, with cutting occurring only on the upstroke. On the downstroke, the rotating cutter¬head draws the fallen muck from the invert into the panzer-type conveyor for rearward transfer. This feature allows time to either reposition ore cars or to exit the tunnel with muck trains while the machine is cutting, as shown in Fig. 5. Boom-Type Rotary Excavators The boom-type rotary-excavator tunneling machines commonly are known as boom-type continuous miners

Jan 1, 1982

By W. M. Cross

The hydrophobic character of sapphire surfaces in SDS solutions was examined with respect to the aggregative nature of the adsorbed surfactant phase. It was found that, at equilibrium, sapphire surfaces having adsorbed SDS bi-layers exhibited no contact angle. Conversely, when the adsorbed SDS was found to be mi-cellar in nature, sapphire surfaces developed significant hydrophobic character. The surface states as detected by Fr -IRIIRS conformational analysis were found to be reversible with temperature. The variation in adsorption density with temperature was studied by in situ Fr-IRIIRS. The isosteric heat of adsorption was calculated to be -1.6 kcal/mole. Although the adsorbed SDS was found to undergo a reversible phase change between 25 and 32°C, similar to SDS in solution, the extent of adsorption was not reversible with temperature.

Jan 1, 1993

By J. Y. Hwang

Sands are utilized to make molds for metal castings in the foundry industry. Approximately a half ton of sand is disposed of for each ton of metal cast in this country. In Michigan, annual sand disposal amounts to about one million tons. A process has been developed in this study to reclaim sands from a steel foundry. Physical separations are utilized in conjunction with other operations (such as the removal of binder, metal, spruce, washes, etc.) to yield silica and chromite sands with desirable molding properties. Several different separation methods, including electrostatic, magnetic, and various gravitational approaches have been examined. Experimental results are presented. The applicabilities of these separation methods are discussed.

Jan 1, 1992

By Charles A. Beasley

Coal conversion to electricity or to substitute natural gas requires a significant quantity of natural and human resources including, in addition to the coal resource base, land, water and the construction and operating labor force. Each method of coal conversion has its advantages and disadvantages relative to conversion efficiency, preferred method of resultant energy transportation, resources consumed, and impact on the environment. Regulations which have been passed in recent years to maintain or restore the pre-project environment can add significantly to the capital and operating costs of both a conversion facility and its associated mine.

Jan 1, 1983