Search Documents

By H. M. Thorne

Industrial shale-oil operations in North America and Europe predated the Drake discovery, but, since then, most have succumbed to competition from petroleum. However, the existence of enormous oil-shale resources in the Green River formation of Colorado, Utah and Wyoming [estimated at over a trillion bbl of shale oil in place] and the advancement of United States oil- shale technology by research and development programs of government and industry during the past 15 years point to a natural partnership of petroleum and oil shale to meet the accelerating energy demands of the future. The utilization of oil shale is not a question of limited petroleum supplies, but one of economics. Two factors are expected to improve the economic outlook for industrial shale oil production -- a rise in petroleum replacement cost and further advances in oil-shale technology.

Jan 1, 1963

By R. Casagrande, L. R. Moore, J. Sessoms, P. Macy

"A South American nickel mine has been producing a nickel concentrate that also contains copper and iron (15 percent nickel, 5 percent copper, 28 percent iron) for the end use of stainless steel production. A critical specification for the quality of the steel is the iron to magnesium oxide ratio (Fe:MgO), with a ratio of below 3.5:1 having a substantial impact on the nickel value. This nickel concentrate producer historically mined the sulfur-rich mineral pyroxenite but had been forced to move to a magnesium oxide/silicate (MgO/SiO4)-rich mineral harzburgite, resulting in nickel recovery being reduced to around 50 percent to maintain the required Fe:MgO ratio. In this study, ore mineralogy, water chemistry and the chemistries associated with the flotation process were evaluated in an effort to increase nickel recovery while maintaining the Fe:MgO ratio according to specification. New chemistry was introduced with the specific goal of complexing with the MgO and retarding its interaction with the bubble flow in the flotation process.IntroductionGlobal nickel production in 2011 totalled to 1,770,000 tons, according to the Raw Materials Group (2013). From 1950 to 2005 there was an aggregate 4.4 percent increase in nickel production, with a market-value high of $1,000/ton nickel reached in 1998 (Mudd, 2010). Approximately 65 percent of nickel production is consumed by the stainless steel industry, with 12 percent of the remainder used in super alloys or nonferrous alloys. Nickel imparts corrosion resistance, temperature resistance and other benefits to its alloys (Table 1) (Oberg, 1996; Cáceres, 2003). The dominant types of nickel-bearing ores are classified as either laterites (limonite: nickel-iron oxide; and garnierite: nickel hydrosilicate) or magmatic sulfide deposits (pentlandite: iron-nickel sulfide) (U.S. Geological Survey, 2013a, 2013b). In 2012, about 40 percent of the nickel ore mined was sulfidic-type ores and about 60 percent was laterite. The processing of laterite ore is expected to continue to increase as the availability of sulfidic ores continues to decline."

Jan 1, 2015

By Tyler Luxner

Stillwater Mining Co. (SMC) is the largest primary producer of platinum and palladium in North America. SMC operates two underground mines in south central Montana, along the 45-km (28-mile) platinum/palladium J-M Reef in the Stillwater Complex. The Stillwater Mine exploits 9.6 km (6 miles) of deposit strike length and East Boulder Mine exploits 4 km (2.5 miles) of deposit length. The two mines are 20.4 km (12.7 miles) apart with SMC controlling a considerable length along the entire J-M Reef trace. Production at the Stillwater Mine began in 1986 and in 1988 the first tunnel boring machine (TBM) was commissioned, becoming an integral part of mine development at SMC. TBMs have been used for developing production footwall laterals (FWL) to access new mining blocks at the Stillwater Mine, as well as boring twin crosscut ac-cess tunnels at the East Boulder. Two TBM development expansion projects are currently in progress: the Graham Creek project at the East Boulder Mine, which will extend footwall lateral development 2,591 m (8,500 ft) to the west, and the Blitz project, where a TBM will be commissioned to extend east out of the Stillwater Mine to 3,658 m (12,000 ft) beyond the current production mining front. General strike and dip of the Reef is west to east and to the north, respectively.

Jan 1, 2012

By Abdallah Khair, Nathalie Risso, Arie Herrera, Victor Tenorio

This study introduces a machine learning strategy to optimize icy regolith extraction from the Shackleton-de Gerlache Ridge using autonomous mining equipment. The model incorporates key parameters—distance, road gradient, vehicle load, speed, recharge logistics, and regolith water content—into a cost framework for excavation, hauling, and dumping. Regression models estimate energy and time requirements; classification predicts terrain navigability; clustering groups craters for efficiency; and K-Nearest Neighbors (KNN) determines optimal routing and scheduling. The system adapts to a six-month daylight cycle to maximize productivity and minimize costs, enabling intelligent planning for sustained lunar resource extraction under extreme environmental and logistical constraints.

Feb 22, 2026

By Steve Kral

As the mining industry watches commodity prices continue to soar, the question on most everyone’s mind is how long will this upcycle last. The con-census among speakers and attendees at the SME Annual Meeting and Exhibit is that this cycle is sustainable. The buzz at the meeting was, of course, the current boom cycle the industry is in. Most agree that China’s huge appetite for mineral commodities is part of the force driving the upturn. But the improving economies of other developing nations also plays a role. However, along with the good times come challenges. Speakers at the keynote session addressed some of the challenges and offered their opinions on the sustainability of the boom.

Jan 1, 2006

By Xin Zhou, Huilin Jia, Xiaofei Liu, Jinxin Wang, Zifeng Meng, Zinan Du, Hui Xie, Guihang Jiang

The change of gas emission or concentration level at the working face is one of the main precursor characteristics of coal and gas outburst. At present, coal and gas outburst monitoring and early warning are mainly based on whether it exceeds the limit and its change law. However, the gas concentration level is affected by factors such as coal seam gas content, permeability, and mining process, and the change law is complex to recognize manually. In this paper, the response characteristics of gas concentration level in the mining process are analyzed and revealed, and a bidirectional long short-term memory model is established. The change characteristics of the gas concentration level in the mining and non-mining processes are studied and recognized. The results show that the change law of gas concentration in the mining process has apparent periodicity and trapezoidal volatility. The proposed intelligent recognition method based on the bidirectional long short-term memory neural network can automatically recognize the underground mining and non-mining processes, and the recognition accuracy achieves 97.7% . The research can significantly help improve the level of coal mine safety management and the accuracy of early warning of coal and gas outburst.

Apr 29, 2023

By M. W. Smith

Pennsylvania has 2500 miles of streams that do not meet water quality standards due to acid mine discharge (AMD), making AMD the greatest cause of water pollution in the state. The problem is mainly caused by abandoned coal mines. Pennsylvania is using a watershed-based approach to abating AMD which includes remining as a key component of a comprehensive restoration strategy. The Tangascootack Creek Watershed was targeted for AMD restoration through remining. Geologic mapping and overburden data were analyzed using Earth Vision software to identify areas of coal reserves which could be remined to improve water quality. Incentives are offered to encourage mining in these designated areas.

Jan 1, 1999

By David N. Hedges

This paper discusses the actual recovery and installation of a longwall in a bituminous coal mine in Western Pennsylvania. The coal bed mined is in the Lower Freeport seam which averages 42 inches (1.07m) in height locally. Drainage from the mine is approximately 3.5 million gallons of water per day (13.25 million liters per day). This water deteriorates the mines predominately fire clay bottom making it extremely difficult to move equipment. Support removal is accomplished by pulling the 6 ton (5443 kg) shields out under their own hydraulic power and transporting them by track over four miles (6437m) co the next longwall panel. This paper also discusses the changes that will be made to aid in the succeeding longwall recoveries and installations.

Jan 1, 1984

By Vivek Priyadarshi, VIVEK KUMAR HIMANSHU, A. K. Vishwakarma, M. P. Roy, A. K. Mishra, RAVI SHANKAR

The nature and orientation of joints in rock strata affect the damage pattern under explosive loading. Most of the limestone deposits in India are found with severity of joints. Categorically, these joints may have variable orientations such as dipping out of the blast face, inside the face, horizontally or having strike parallel to the face. The damage pattern under the varying category of orientation will be different. Accordingly, a numerical model in Ansys-Explicit Dynamics was prepared to compare the damages of rock mass under different joint orientations. The physical nature of a joint reflects frictional and stiffness behaviour. Accordingly, the damages have been compared under bonded and frictional nature of joints. The output damage pattern from the model has been validated on the basis of blastability index proposed by Lilly. Different limestone mines in India show different nature of jointing in their rock strata. Accordingly, the blasting outputs from three different limestone mines, viz. Rawan limestone mine, Sagmania and Birhauli limestone mine and Injepalli limestone mine, have been compared along with their blast design parameters and the nature of joint. The comparative results show that the closely spaced horizontal joints support maximum in burden movement and rock fragmentation due to blast.

Nov 23, 2023

By A. Vien

A major thrust in Industrial automation over the past few years has been the exploration and incorporation of higher level (supervisory and optimizing) control strategies aimed at more fully exploiting the existing control system infrastructure. There is little doubt that this is worthwhile pursuit, however, one must not lose sight of the maintenance and development requirements of the basic control system. Statistics on loop performance indicate that this too is an area of considerable potential. In this paper the authors look at some of the less elegant, but arguably equally important issues in mineral processing plant control. The focus is on controller structures, loop tuning, sampling, filtering, and some of the other principal components of the regulatory control foundations. In many cases significant improvements In control performance can be achieved by getting back to the basics.

Jan 1, 1998

By V. Herman, B. Knorr, D. Whalen

"Edge effect is a condition widely observed in High Pressure Grinding Roll (HPGR) operations that gives rise to reduced comminution at the edges of the roll surfaces. This effect is caused by a reduction in the local crushing pressure at the edges of the rolls resulting from the sliding friction between the static cheek plates and HPGR feed material. Practically, this has an impact on equipment sizing, as the edge effect leads to coarser particles reporting to downstream equipment in open-circuit operations and increased circulating load and diminished HPGR circuit capacity in closed-circuit operations.To address this, Metso's HRC™ HPGR incorporates an Arch-frame to maintain a parallel relationship between the rolls and allow for the use of a flanged roll design. We conducted a series of pilot-plant tests with a 750 mm by 400 mm HRC HPGR to compare the performance of the flanged roll design against that of a traditional cheek plate arrangement under similar operating conditions. The edge effect was found to be significantly reduced with the flanged roll design. Based on the pilot-plant results, the implications for circuit design, energy efficiency and overall plant performance in a full-scale application were investigated and discussed.IntroductionGlobal trends such as lower ore grades and rising operating costs are driving the market toward more energy-efficient mineral processing solutions, most notably in comminution circuit design. High pressure grinding rolls (HPGRs) have been recognized as an energy-efficient solution relative to more conventional circuit designs. The basic operating principle of HPGRs, in which a fairly uniform pressure is applied to a bed of material in the compression zone, lends itself to this improved energy efficiency (Morley, 2006). Studies have estimated that savings of 10-15 percent are possible when comparing an HPGR circuit with a traditional SABC circuit (Rosario and Hall, 2008). While HPGRs offer a more energy-efficient solution than tumbling mills, there is still room for improvement in many aspects of the design. Edge effect, in particular, is one such aspect that limits the effectiveness of the machines. Edge effect is the impaired performance at the edge of the rolls due to a reduction in crushing pressure (Morley, 2010; van der Meer, 2010). As described in our prior work (Knorr, Herman and Whalen, 2013), edge effect is caused by the interaction between the ore entering the crusher and the relatively static cheek plates positioned at the edges of the rolls. As the material is drawn into the crushing zone, the sliding friction between the ore and the cheek plates inhibits the ability of material to be effectively drawn into the compression zone at the edges of the rolls. This reduces the crushing force in those edge regions relative to the center of the roll where material is being drawn into the compression zone at a higher rate. In addition, the cheek plates of a traditional HPGR design are held in place by spring-loaded brackets that are adjustable to manage the clearance. This spring-loaded cheek plate design prevents full compression of the material in the edge regions of the roll as there is relief at the outer edges."

Jan 1, 2016

By Jorge Alberto Soares Tenório, Denise Crocce Romano Espinosa, Morgana Rosset, Bárbara da Rocha Pereira

High-purity alumina finds application in various electronic industry sectors, with approximately 100 million tons of this compound being produced worldwide. Alumina is acquired through the mining process of bauxite, a rock composed of a mixture of minerals such as gibbsite, kaolinite, hematite, and either anatase or rutile. In 2020, both bauxite and alumina were included in the list of critical raw materials. Due to the demand for high-purity alumina production, the development of a methodology to remove impurities present in the leach liquor from bauxite processing by solvent extraction (SX) followed by precipitation has been widely studied. This work aims to obtain high-purity alumina from bauxite by a solvent extraction process followed by a precipitation step from the sulfur leach liquor obtained by the thorough dissolution of Al and Fe from bauxite. Different parameters were evaluated in the SX step, such as extractant type, pH, temperature, and volume-to-volume ratio. The results indicated that using Alamine 336 as an extractant at pH 0 and room temperature led to an extraction of 90% of Fe and 15% of Al. Aluminum sulfate was completely precipitated as aluminum hydroxide and 55% of Fe using NH4OH. After the calcination procedure, obtaining a 99.9% pure alumina was possible without generating a red mud-similar residue.

Dec 28, 2023

By Richard F. Hammen

Mineral extraction from sulfide ore deposits usually leads to the combined action of oxygen and water on the newly exposed ore. The result is acid mine drainage, a low pH solution of various metal sulfate salts and sulfuric acid. Paradoxically, the valuable metals dissolved in acid mine water are a liability because they are too toxic for discharge but too dilute to recover economically. The expense of compliance with water quality release standards has reduced the profitability of many mining operations. Solid phase extraction (SPE) columns have been developed to extract metals from acid mine water. These columns are designed to remove the toxic elements from water and recover the metals as purified fractions. This article describes the results of a Phase 1 bench-scale project to test the performance of the SPE columns. The tests were conducted with water collected from the abandoned Berkeley Pit copper mine in Butte, MT.

Jan 1, 1993

By Andrew Chegwidden, Tara Wilk

Shaft 18B-1 is the second shaft to be constructed as a part of contract C547A along the New York City water supply system Tunnel No. 3. More complex than Shaft 17B-1, this site has an additional 30 m (100 ft) of overburden for a total excavation depth of approximately 78 m (256 ft) through water-bearing overburden soil and 145 m (475 feet) of gneiss bedrock to connect to the underlying Water Tunnel No. 3. round freeing was specied as the method to provide temporary earth support and ground water control for the overburden material. An extensive supplemental geotechnical investigation (SGI) and frozen soil testing program was performed to develop the design of a temporary ground freezing system, consisting of over 7,315 m (24,000 ft or 4.5 miles) of drilling for the installation of 95 freeze pipes. At the start of shaft excavation, the upper sandy silts strata was found to have an unprecedented low thermal conductivity, leaving the frozen soil face approximately 0.6 to 1 m (2–3 ft) behind the cutline. The ground freezing earth support needed to be augmented with ring beams and liner plates to support this soil face and allow for the excavation to proceed and be completed safely.

Jun 23, 2024

By Alan Bauer

In recent years there has been increasing interest in employing the technique of explosive casting in strip mines. Explosive casting, applied to dragline mining, describes the procedure whereby the overburden is horizontally displaced by blasting causing a portion of the material to be thrown into the previously mined cut. Therefore, it is not necessary to subsequently excavate this waste with the stripping equipment. In addition, allowing the overburden unrestricted movement during the blast most often results in improved fragmentation and enhanced machine productivity. The method is receiving attention because the capital and maintenance costs of stripping equipment has risen rapidly in relation to explosives costs. Improved productivity is necessary to maintain unit costs at an acceptable level.

Jan 1, 1983

By J. P. Matoney

In recent years, the diminishing supply of natural gas has led energy suppliers and consumers to consider making synthetic natural gas from coal. A number of processes have been devised to produce gas from coal; many of these have been operated at the pilot stage and some have been operated commercially. Each process has specific coal feed stock requirements with respect to size consist and moisture content. The purpose of this presentation is to compare the estimated costs for coal handling, live storage, size reduction and drying facilities that would be required for delivery of coal feedstock to different gasification processes.

Jan 1, 1977

By P. Lan

Gold is often associated with arsenopyrite in many refractory gold ores. The selective recovery of arsenopyrite by flotation is therefore necessary in order to maximize the recovery of gold. However, the complexity of arsenopyrite flotation often makes it difficult to obtain a high recovery from real lean gold ore. This paper presents the results of arsenopyrite flotation by ultrasonic pretreatment in micro flotation experiments and bench scale flotation tests. The tests showed that pure arsenopyrite exhibited low natural floatability due to the oxidation on the mineral surface under ambient conditions. Using ultrasonic pretreatment, the oxidation film was ruptured and the floatability was enhanced greatly. The presence of Fe (III) was found to inhibit the flotation of arsenopyrite and this depression was also removed by the ultrasonic pretreatment. This result explained why the arsenopyrite in real ore is often difficult to float and how ultrasonic pretreatment can effectively improve the arsenopyrite flotation in real gold ores. Guanidine (GMM) was found to be a superior collector for arsenopyrite in acidic medium and xanthate in alkaline medium.

Jan 1, 1998

By G Luxbacher

Computer simulation of mine ventilation systems is rapidly becoming an essential tool in mine planning and design. This paper examines the utilization of ventilation simulation techniques to evaluate the number, shape, size and layout of mine entries in a typical coal mining system. Since the mains and sub-mains serve mainly for transportation and ventilation and the ventilation system is critically important to the health and safety of the workers, there exists a great need for optimal designs in this area. Evaluation criteria, could include, among others, minimization of power costs, shaft requirements and leakage. Constraints of this optimization problem include health and safety regulations and production and mine infrastructure requirements.

Jan 1, 1977

By A. S. Kastrinos

There are many concepts of preventative maintenance. The basic objective of all maintenance organization, however, is the efficient (accomplishment and control of all) inspection, repair, overhaul, material and preventative maintenance functions necessary to maintain facilities and equipment in a condition that will meet operating requirements at a level consistent with low costs and high availability. To formulate a preventative maintenance program requires sound judgment and the ability to apply in a practical manner a system that meets Plant operation requirements, based upon organization, experience, conditions, design and historical data. A maintenance program must be divided into to categories consisting of: 1. Scheduled tasks to be accomplished at planned intervals. The objective of these tasks is to maintain reliability and prevent as much as possible abnormal failures. 2. Non-scheduled tasks that result from periodic reports and which can be scheduled to fit in conveniently with other routine work. The non-scheduled work items may include long-range preparation for lenghty shutdowns requiring Engineering and Shop services.

Jan 1, 1975

By Langtry E. Lynd

The titanium dioxide pigment industry in the United States has always relied to varying degrees on imported titanium concentrates. Dependence on foreign ilmenite was especially high (generally over 85% of consumption) until 1942, when large-scale U.S. production of ilmenite began, and has since ranged from 12% to 47%. Rutile import reliance was generally in the 45% to 80% range until the early 1960's, when increased use in the chloride pigment process raised dependence on imported rutile to over 90% in most years since 1963. Import reliance of zircon, obtained almost entirely as a byproduct of titanium mineral production, has generally ranged from about 30% to 65% of consumption. This paper will examine the history of U.S. sources of these heavy mineral commodities, and will discuss the potential U.S. future supply in view of changing industrial uses and processes and the anticipated development of new heavy-mineral-sand processing operations, such as those at Richards Bay in the Republic of South Africa and in Sierra Leone.

Jan 1, 1978