Search Documents

By Gregory Rumbaugh, Christopher Mark

Recent pillar collapses have caused five large airblasts in underground U.S. limestone mines. One of these events injured three miners, but all of them put many other miners at risk. To better understand the hazards, Mine Safety and Health Administration (MSHA) conducted a comprehensive review of the international literature on airblasts. More than 40 airblast cases have been documented, in a wide variety of minerals. Experience shows that miners that are in the direct path of the air as it moves towards the mine exits are at the greatest risk. The paper describes a risk management methodology that can be used to evaluate the level of hazard throughout the mine and aid in the selection of controls to reduce the risk. The paper concludes with a detailed case history of an actual pillar collapse and airblast.

By A. J. Plumpton

Centrifugal air classification and li-quid-phase sedimentation are the principal methods of industrially sizing materials of dimensions smaller than those handled by screens. Increasing application of materials such as composites and high performance ceramics has furthered the need for closely-sized, fine, industrial mineral and synthetic products of controlled properties. Sedimentation can be used to separate very small sized particles but introduces problems of liquid-solid separation, de-agglomeration and drying. Some of the advantages and limitations of centrifugal air classification will be discussed and laboratory and plant measurements using centrifugal machines will be presented to support the discussion.

Jan 1, 1990

By Herry Poernomo, Agus Prasetya, Iga Trisnawati, Himawan Tri Bayu Murti Petrus, Gyan Prameswara, Panut Mulyono

We studied yttrium extraction from untreated zircon sand processing waste tailings. Xenotime mineral as the rare earth element source with an abundance of yttrium (REY) was detected in sufficient grade for extraction. As much as 9.03% yttrium exists in zircon tailings (analysed by X-ray fluorescence spectrometry). The presence of yttrium was confirmed by X-ray diffractometry in xenotime minerals, which are yttrium carriers (Y-PO4). The purpose of this research was to determine the effect of leaching conditions on yttrium recovery from zircon sand after alkaline fusion treatment. Alkaline fusion was chosen to decompose phosphate into hydroxide in the xenotimemineral,which will reduce further required hydrometallurgical processing.Alkaline fusionwas carried out for 3 h at 450 °C, with a ratio of sodium hydroxide to zircon tailings sand of ~ 1:1. The alkaline fusion product was leached with water, followed by hydrochloric acid treatment to leach the yttrium. Yttrium recovery reached 87% under optimum conditions (60 °C, 1MHCl, and solid-to-liquid ratio = 1/10 for 7.5 min). A suitable model for yttrium dissolution with hydrochloric acid was diffusion through a solid particle ash layer. The calculated activation energy (EA) for this model was 20.21 kJ/mol.

May 26, 2020

By Jason Swartz, Gerardo Gomez, Henry Leighton

San Antonio has experienced sustained growth for decades, putting increased pressure on existing wastewater infrastructure. In June 2013, San Antonio Water System (SAWS) reached a Consent Decree agreement that requires significant improvements to the wastewater system over a 10-year period to reduce Sanitary Sewer Overflows. One of the critical projects was the W-6 Upper Segment Tunnel project to reduce sanitary sewer overflows on an existing sewer main running through Lackland Airforce Base. The replacement project consisted of a new tunnel nearly 29,000 LF of primarily 104" FRP. The project also includes nine shafts and multiple trenchless crossings to make near surface connections to the new works.

Jun 23, 2024

By J. Ye

A comprehensive flotation study has been carried out on a Chinese fluorspar ore using the packed flotation column developed at Michigan Technological University. The results are compared with that of a conventional mechanical flotation method on the same feedstocks. Key factors controlling flotation performance of both methods are evaluated based upon a simple statistic design. The flotation concentrate produced in one stage of the packed column has 4-S% higher recovery and much lower silica impurity content than that produced by up to six stages when a conventional mechanical cell is used. The results also show that the packed column flotation process is particularly suitable for recovery of finer fluorspar particles.

Jan 1, 1992

By D. A. Longhurst

Improper size distribution of the grinding media in a multicompartment mill can be a source of many operation problems encountered. Inefficient use of the power expended for grinding, and an undesirable product size distribution are two frequent resultants. It is necessary to resize the grinding media in the leading mill compartment at time intervals related to the abrasive nature of the material being processed. In practice, this is done when time permits and with sketchy guidelines, if any. Maintenance of the grinding media size distribution can be scheduled, and would be, with a realistic method supplied to the user.

Jan 1, 1984

By M. L. Young

Hindered settling columns are used throughout the minerals industry for both size and density separations. In this study, the performance of a continuous, laboratory-scale hindered-settling column was evaluated for various particle systems. The test variables included solids composition, water rate, and column height column performance was evaluated using partition curves and corresponding performance parameters.

Jan 1, 1999

By G. D. Hood

The U.S. Bureau of Mines investigated rapid froth flotation through the use of more efficient bubble-particle collisions that improved the overall flotation kinetics. An in-line static mixer efficiently mixed the air bubbles, water, and ore, rapidly attaching the hydrophobic mineral to the bubble surface. As the mixture entered the flotation chamber, the hydrophobic mineral was already attached to the bubbles and was quickly floated away from the remaining ore pulp. A rougher concentrate containing 4.5 pct copper was obtained from a western porphyry copper ore containing 0.67 pct copper. Over 99 pct copper was recovered from the ore at a rate 7 times faster than conventional flotation.

Jan 1, 1991

By H. EI-shall

In this paper, the results of bench scale testing of five different flotation processes to separate dolomite from phosphate are discussed. The effectiveness of each process interms of phosphate recovery and MgO content in the concentrate is used together with the reagent consumption as the basis of comparison. The water quality is found to play a major role in the performance of these processes. Effect of water hardness as well as other parameters are discussed.

Jan 1, 1995

By VIVEK KASHYAP, EVODY TSHIJIK KARUMB, PATRICK TAYLOR

Zinc ferrite is considered an integral phase of zinc residues as their presence can render the processing of zinc and critical metals difficult. It is a refractory phase, formed at high temperature in the presence of zinc (Zn) and iron (Fe) during oxidative roasting in zinc processing plants. Because it is refractory to efficient leaching, unreacted zinc ferrite gets concentrated in the final zinc residue, making it a viable source of zinc and indium extraction. The refractory nature of zinc ferrite makes the extraction of associated critical metals difficult. In order to explore a potential economic and carbon-neutral zinc ferrite processing technique, our previous study proposed the partial reduction of zinc ferrite followed by sulfuric acid leaching of the roasting product [1-3]. As demonstrated in our previous studies, partial reduction of zinc ferrite results in a mixture of ZnO, Fe3O4 and FeO, which can be further subjected to leaching for efficient extraction of zinc and critical metals such as gallium and indium.

Dec 1, 2022

By Jaeheon Lee, Junmo Ahn, Jiajia Wu

To reduce the environmental footprint of hydrometallurgical processing of black mass from spent lithium-ion batteries (LIBs), a green leaching system based on glycine and sodium metabisulfite (Gly-SMS) was proposed. The leaching study demonstrated that the highest cobalt and lithium recoveries of 100 percent and 99.8 percent were achieved under optimal conditions. The leaching mechanism revealed that the dissolution of LiCoO2 in the Gly-SMS solution followed the shrinking core model. The apparent activation energies for cobalt and lithium were determined as 48.05 and 41.51 kJ/mol, respectively, indicating a surface chemical reaction controlling mechanism. The leachate was then processed by an acidification- precipitation technique with oxalic acid as the precipitant to remove cobalt. Glycine complexes with metal ions by zwitterionic ligand and recycles in the leaching-precipitation circuit, reducing the reagent cost. Compared to other studies, this leaching system has near-neutral operating conditions and is cost-effective, making it an economically viable alternative for treating cathode materials from spent LIBs.

Dec 1, 2024

By D. Shaver, M. N. Badonie, J. Newcomer, V. T. McLemore, E. Owen

Rare earth elements and critical minerals have recently become of great economic interest because of their necessity for many new technologies and recent geopolitical unrest affecting the supply and import of resources. The San Juan and Raton basins in northern New Mexico are two structural coal basins that contain elevated concentrations of rare earth elements and critical minerals. These two New Mexican coal basins will be assessed geochemically and petrographically to identify vectors of the rare earth element and critical mineral enrichment. Coalbeds, coal seams, overlying, and underlying rock units will be sampled and characterized to determine any economic viability. Historic data will be compiled into a new and comprehensive coal geochemical database, which will grow with new analyses, and serve as the dataset for this project; this coal resource database will be made available to the public.

Feb 1, 2023

By Felicia F. Peng

Using granular media for removal of soluble manganese from mine water and industry waste stream has the advantage of forming a compact surface layer of manganese oxide coating on the media. This process can avoid the step involving the separation of voluminous sludge of manganese hydroxide by the high-pH method for soluble manganese removal. The removal of soluble manganese is accomplished by adsorption and oxidation. The adsorption of Mn(II) on the manganese oxide-coated media was rapid through the specific adsorption and may be due to the ion exchange of hydroxyl ions on the manganese oxide by Mn(II). In the subsequent step, the adsorbed Mn(II) form the intermediate manganese complex on the manganese oxide product is oxidized with dissolved oxygen or other available oxidant source in the aqueous solution. This paper presents the efficiency of removal of soluble manganese from mine water by using a laboratory fluidized bed and the recovery of manganese oxide coating on the anthracite coal particles. In order to accelerate the formation of the manganese oxide layer on the surface of anthracite media, dilute potassium permanganate solution is used as an active oxidant. The effects of operation parameters on the manganese removal including pH, flow rate, concentration of feed and oxidant dosage are evaluated.

Jan 1, 1996

By N. Arbiter

Evidence for the floatability of sulphide minerals without collector is analyzed and it is shown that results obtained with ores, in contrast to those with single minerals or mineral mixtures, depend on many additional variables, some identified and others not. Because of the prevailing low levels and costs of collectors for most sulphide ores, it is unlikely that collectorless flotation will have commercial applications, so that continued research on the subject may be justifiable on theoretical but not on practical grounds.

Jan 1, 1993

By Y. Zhang, M. Yekich, C. Zhou, C. Jobes, J. Galanko, D. Tuchman, J. Srednicki, J. Carr

The continuous personal dust monitor (CPDM) is an essential instrument for working in hazardous environments, is used to monitor real-time coal dust exposure, and is mandated by the Mine Safety and Health Administration (MSHA) for underground coal mines. Researchers from the National Institute for Occupational Safety and Health (NIOSH) found that it is possible for electromagnetic interference (EMI) between a CPDM and a proximity detection system (PDS) to occur. Various approaches have been taken by researchers and manufacturers to address this EMI issue. Administrative controls were recommended to keep the CPDM six inches away from the wearable PDS device. Shielding pouches were made to contain the electromagnetic (EM) emission from the CPDM. Metal shielding was added to major EM emitting components. EMI filtering with large capacitors was introduced to mitigate EMI. Most recently, a novel magnetic-field-cancellation-based approach was developed and achieved remarkable results. In this paper, we provide a comparison between these approaches. The pros and cons of each approach are presented and discussed, so that mining device manufacturers and operators can best evaluate the technology and controls that improve the health and safety of mine workers.

Feb 1, 2023

By Simón Díaz‑Quezada, Ernesto Arancibia, HUMBERTO ESTAY, Tomás Vargas

In situ leaching (ISL) is an attractive technique that enables copper recovery from copper oxide ores that are either low-grade or located at depths too great to be economically exploited through conventional methods. At present, in situ leaching (ISL) has been applied to intact copper oxide ores, in particular, those which (i) present a good natural permeability and (ii) do not require preconditioning. Many copper oxide ores present low natural permeability. These are located above the water table and need preconditioning for the ISL application. The present work shows an economic assessment of the application of ISL to this type of copper ores. The preconditioning technique considered here involves the application of partial mining by sublevel stoping by removing a small fraction of the ore. This technique results in forming an ore bed with good permeability and good solution collection at the stope base. The economic assessment of this approach suggests that it can be implemented with positive net present values to copper oxide ores located at depths in the 100–300 m range, with copper grades above 0.4%. The maximum acid consumption values are below 52.5 kg/t, with blasting procedures designed to produce an ore bed with an average particle size below 6″. The breakdown of operational costs indicates that the mining cost is still very high, accounting for up to 60% of the total operating costs. Therefore, optimizing mining procedures is still necessary for improving the economic outlook of this approach and thus expanding the application field of ISL.

Feb 4, 2023

By P. R. Taylor

Batch leaching experiments have been performed to study the kinetics of galena leaching in fluosilicic acid solutions with oxidants. Variables studied included: fluosilicic acid concentration, oxidant type, oxidant concentration, particle size and leaching temperature. It was found that hydrogen peroxide was the most effective oxidant, compared to the others studied, and the effect of the oxidant concentration on the leaching behavior of galena was very significant. Also, decreasing the particle size and increasing the leaching temperature increased the extraction rate. The initial, apparent activation energy was calculated to be 11.72 kJ/mole (2.8 kcal/mole) and suggested that galena leaching in fluosilicic acid solution, with hydrogen peroxide as an oxidant, may be controlled by fluid film mass transfer initially. The reaction appears to be retarded by the formation of elemental sulfur and the sulfur oxidation becomes a major resistance to the overall leaching reaction.

Jan 1, 1992

By P. Samanta, Mohammed N. Azad, Gustad F. Taraporewalla, A. K. Mukherjee, Abhay S. Patra, D. Sachinraj

Beneficiation of coal is a water intensive process, and the water is recovered in downstream operations in the high rate thickener (HRT) and vacuum belt filtration (VBF). Clean coal particles entering the HRT have an inherent tendency to enter the overflow because they are extremely fine and hydrophobic. Hence, flocculants (polymers) are used to floc the ultrafine particles so that they settle and enter the underflow. Ultrafine coal particles (−37 μ), which are highly hydrophobic, if present in the stream, will not be efficiently captured by using flocculants alone. This is observed in the normal plant operation at one of the beneficiation plants in the Jharia region, Jharkhand, India. Approximately 6–7% of the feed to the HRT enters the over flow (supernatant water). Hence, this amount of clean coal particles is not recovered and account for production losses. A comprehensive settling and dewatering test work was conducted with clean coal slurry using several commercially available reagents. Studies were also done on different combinations of reagents, including coagulants and surfactants along with flocculants, to improve the settling behavior of the coal particles. The reagents were assessed based on their performance with respect to settling rates, overflow water clarity, and compaction of the underflow solids. Emphasis was given to the ability of the reagents in compacting thickener underflow to higher densities so that maximum water could be recovered from the thickener. Pretreatment of highly hydrophobic coal slurry with a combination of coagulant and surfactant followed by flocculation showed very good settling characteristics with clear overflow.

Sep 30, 2021

By A. W. Khair

This paper presents an engineering approach to solve a complex ground control problem at reduced cost, allowing the mine to be operated safely and economically. The mine has experienced serious and complicated cutter roof problem in the entries. This cutler roof problem has delayed the advance of the entry development considerably and cost of these entries is very high due to the requirement of very heavy artificial supports. The analysis includes assessment of the cause of cutter roof and step by step action taken to improve the entry condition through appropriate longwall panel entry design and roof support system. The approach for solving the problem was two-fold: 1) to apply yield pillar concept in order to reduce the effects of in-situ horizontal stress in the roof strata and 2) to find an effective way to reinforce the roof strata and to support the fractured roof and avoid caving.

Jan 1, 1990

By William Gleason

"While the American Exploration & Mining Association (AEMA) was preparing to close one chapter and begin another during its annual conference in Spokane, WA Dec. 3-7, word of a significant victory on an issue that has been important to the association for many years came from the halls of Washington, D.C.During a keynote address on Dec. 6, Joe Balash, assistant secretary of Land and Minerals Management for the U.S. Department of the Interior (DOI), told a sold-out lunch crowd that the DOI had released final drafts of proposed revisions to the Obama-era greater sage grouse conservation plans. The revisions suggest removing hundreds of thousands of acres of federally protected habitat in Utah, and easing restrictions on energy development and other activities, including mining, in Colorado, Idaho and Wyoming.The protections of the sage grouse were put in place by the Obama administration in 2015. The sage grouse, a prairie fowl, is considered by conservationists to be a key indicator species for the health of America’s sagebrush ecosystem. The previous plan to protect the ground-dwelling bird imposed restrictions to development in sage grouse habitat, but did not place the birds on the endangered species list — a move that many believed would have imposed far more rigid rules.AEMA, and its executive director Laura Skaer, led the way in the fight against the Obama-era greater sage grouse plan, arguing that the plan unnecessarily hurt economic development.“We were the first organization to point out that the greater sage grouse was being used to stop mining, oil and gas production and grazing on public lands in the interior mountain west,” said Skaer who is retiring from AEMA with a significant legal win on this front. “Early on, we cautioned that the proposed Land Use Plan Amendments would be worse than a listing (of the sage grouse) under the Endangered Species Act. Very few believed us until they saw the plans with all of the restrictions and the recommendation for a 4-million-ha (10-million-acre) withdrawal from mineral entry. We were the only organization that filed comments on all 88 Land Use Plan Amendments in 11 states covering more than 24.2 million ha (60 million acres).”"

Feb 1, 2019