Search Documents

By T. McDonald

Test work indicated and plant operation has since confirmed that SAG milling is a viable option for INCO's Sudbury Operation milling rationalization project only if pebble crushing is included in the SAG/ball mill circuit. Throughput increases more than fifty percent with pebble crushing incorporated into the comminution process. The finer product of high speed pebble crushing provides further energy savings. The unconventional approach of pumping the pebble crusher product, while simplifying plant layout, has produced challenging wear problems.

Jan 1, 1992

By Joseph M. Driscoll

After 30 years of successfully mining gold, Newmont Gold has temporarily ceased production from the original Carlin Pit. In late 1993, the Carlin East decline was driven and an extensive underground exploration program was started. Today, Newmont Gold produces refractory ore from the Carlin East Underground at the rate of 864 t/d (950 stpd). Annual production is more than 3.1 t (100,000 02). More than 70 underground miners will be employed during Carlin East's estimated six-year mine life. About 70% of the ore at Carlin East is mined by mechanized longhole stoping with delayed, cemented backfill. The remaining ore is mined by underhand drift and cemented fill methods.

Jan 1, 1997

By P. T. Bissert, D. S. Yantek, L. Yan, M. D. Klein

Federal regulations require that refuge alternatives (RAs) be located within 305 m (1,000 ft) of the working face and spaced at one-hour travel distances in the outby area in underground coal mines, in the event that miners cannot escape during a disaster. The Mine Safety and Health Administration mandates that RAs provide safe shelter and livable conditions for a minimum of 96 hours while maintaining the apparent temperature below 35 °C (95 °F). The U.S. National Institute for Occupational Safety and Health used a validated thermal simulation model to examine the mechanisms of heat loss from an RA to the ambient mine and the effect of mine strata composition on the final internal dry bulb temperature (DBT) for a mobile tent-type RA. The results of these studies show that 51 percent of the heat loss from the RA to the ambient mine is due to radiation and 31 percent to conduction. Three mine width and height configurations and four mine strata compositions were examined. The final DBT inside the RA after 96 hours varied by less than 1 °C (1.8 °F) for the three mine width/height configurations and by less than 2 °C (3.6 °F) for the four mine strata compositions.

Jan 1, 2016

By Alex Stewart

Most iron bearing ores treated by the R=N Direct Reduction Process yield products lower in phosphorus than the initial ores. The sulfur is also removed and generally is in the range of 0.02 to 0.05 percent in the final R=N product, independent of the sulfur content of both the ore and carbon fuel used. The mechanism and thermodynamic justification of the principal reactions leading to the removal of both phosphorus and sulfur and the control of sulfur in the iron concentrate produced are discussed and supported by the results of laboratory experiments. In substantially all iron ores (containing up to 4% sulfur as sulfate) and solid carbon fuels (containing sulfur from 1 to 8%) tested, the rejection of sulfur has been in the order of 90-95%, with not more than 0.02 0.05% sulfur in the final metallic iron product. With respect to phosphorus-bearing iron ores ranging up to 0.70% P205, the rejection to tailings has been in the order of 70-95%, resulting in not more than 0.03 - 0.07% phosphorus in the final product.

Jan 1, 1958

By C. Roos

"Mining companies have included quantifying uncertainty, or at least risk, as a requirement of project justification for many years. However, many times this process lags behind the traditional mine planning process and the results are rarely used to improve the plan. Nearly every parameter used in a mine plan is an estimate and the mine planning engineer should recognize, and even embrace, the inherent uncertainty in those parameters and its effect on their forecast results. While many of the uncertainties are beyond the scope of the traditional mine plan (e.g. global market uncertainty, socio-political uncertainty, environmental uncertainty), some uncertainties can, and should, be included in the mine planning process.Many mining engineers have incorporated techniques such as Monte Carlo Simulation or Discrete Element Simulation to understand the range of productivity that can be expected for an operation, but most still rely upon one estimated model for what is likely the critical component of technical uncertainty, the geologic resource. Modern geostatistical methods can provide multiple orebody realizations to provide a thorough unbiased picture of the geologic uncertainty. However, most traditional mine planning techniques are not formulated to allow for multiple (100-200) realizations of each material quality/grade parameter.Commercial software companies and research groups are progressing with development of tools that can incorporate geologic uncertainty, and even optimize extraction plans in the uncertain environment. Unfortunately, this author believes that a significant number of mining operations will not be able to adopt these techniques due to the computational requirements of the advanced techniques and the costs associated with implementing proprietary software. In an attempt to encourage mining engineers to embrace the inherent uncertainty in their mine plans, this article presents a cost-effective alternative that can be developed in-house, at any mine, to schedule mid- to long-term mine plans while continuously monitoring the uncertainty in the results. The aim of this article is that by demonstrating the usefulness of such a system, mining companies will encourage engineers, geologists and geostatisticians to find ways to incorporate this powerful data into their processes and procedures."

Jan 8, 2017

By Ken A. Pfaff, Ray Daigh

This paper will discuss state-of-the-art applications of GPS automation in mobile conveying systems. Robotic mobile conveying systems increase profitability, optimize stacking and reclaiming operations, and control complex interfaces more accurately than other systems. We will also discuss the application process in machine-to-machine coordination, selection of the appropriate GPS system, and Ethernet considerations. As the leading supplier of GPS-controlled mobile conveying systems, we'll draw on our experience at Morenci, Radomiro Tomic, Zaldivar, El Abra (Figure 1), and El Tesoro mines in the US and South America to demonstrate system reliability and the lessons we've learned through analysis of these projects.

Jan 1, 2002

By D. K. Sengupta

Increased recycling of waste paper has been emphasized in recent years in both the USA and Canada for environmental and economic reasons. Removal of ink particles from the waste paper pulp is therefore necessary. One of the most promising methods for ink removal is froth flotation. Our study investigated the feasibility of a simplified flotation scheme which showed that about 90-92% ink removal can be achieved while 95-97% ink removal is achievable if a hydrophobic polymer is used ahead of flotation. The clean paper pulp recovery was over 90%. The effects of pulping pH, flotation pH, and concentrations of flotation and polymeric reagents are discussed in the paper.

Jan 1, 1993

By Brian H. Kaye

Efficient design of grinding circuits for efficient production of ultrafine material requires rapid feedback of information concerning the fineness of material leaving the grinding device. Generating this information requires efficient sampling and adequate rapid characterization of the material leaving the grinding machinery. Recent developments-in electrooptic inspection of dry end wet material leaving a grinding device are critically reviewed. New methods for characterizing ultrafines are discussed. A rapid operating automated cybernetic (intelligent) permeability device for automatic control of grinding circuits using Blaine index and other fineness indices is described.

Jan 1, 1983

By Jerry R. McGaha, Joseph A. Dos Santos

The favorable economics of conveyor based haulage, especially in moving large volumes. has long been acknowledged. This has given impetus to significant developments over the last two decades in conveying systems and equipment. Such developments have resulted in improved equipment and system reliability, versatility and mobility. The present writing presents conveyor systems and their variations. Long overland conveyors of various profile and plan layout are considered along with various typical support systems. This includes discussion of horizontally curving, two-way and booster driven conveyors. High Angle Conveyors-[HACs] are reviewed, citing in-pit as well as plant application. Finally, several important advances in idler and in pulley design are presented.

Jan 1, 1989

By Leonardo Rosas Sánchez, Darío Ángel Bulla

"The two track road sector between Cisneros-Loboguerrero (having a length of 14 km and 11 short unidirectional tunnels) is a new highway still on construction located along the existing Highway Buga – Buenaventura (Colombia). Due to the steep topography, difficult geological/geotechnical conditions, the traditional portal construction approach was impossible to be implemented in eleven (11) of the twenty two (22) portals. In this specific project, the skewed portal approach was developed as the optimal and more effective solution. The construction time and costs of portals were reduced in 21 months and 75%, respectively. At the same time, the natural equilibrium of the slopes was maintained, thus, facilitating adequate safety factors along the useful life of the project. This document pretends to show a detailed design experience (and the construction of the entry portal of tunnel 11 (left)). INTRODUCTION The Cisneros-Loboguerrero project is a 14 km length dual lane highway, connecting productive zones with the Pacific Ocean along the current Bogota-Buenaventura highway as shown in Figure 1. The project is located at the northern side of the Dagua River Valley. The preliminary design suggested constructing portals under challenging topographical conditions, i.e., slope cuts having heights between 50 to 100 m (some having slopes > 100%) requiring complex developments and having very high risks.The entry portal of tunnel 11 (left) was the first portal successfully built by implementing the skewed portal approach. Later, this approach was used as a model for the construction of the other ten (10) portal having similar topographic and geotechnical conditions. The development of this new alternative provided a considerable reduction on the construction time of portals, thus relieving a critical path in this project."

Jan 1, 2016

By L. Adler

The valuable Maximum Utilization Factor (MUF) concept has been extended to other rotating excavators beyond stripping shovels and draglines. In this concept the boom reach and bucket capacity are multiplied to get an MUF, then normalized by dividing by the equipment weight. Statistical analyses were applied to the remaining shovels (hydraulic and cable), draglines, and backhoes. Positive correlations were found. Stripping shovels and draglines were also re-examined. The results provide an estimate of equipment diggability and encourage versatility by the interchange of the boom and the bucket. The concept further clarifies the existing equipment classification by delineating general excavating, loading, and stripping kinds. The results also forecast trends, and noted innovative advances and possible retrogression. Extension to other boom excavators, such as front-end loaders is recommended. The MUF concept provides one of the few indices of gross external characteristics available to the engineer-user of equipment.

Jan 1, 1990

By J. F. Allan

The main conditions which affect investment in mineral exploration and development are compared in five countries currently considered attractive for mineral investment - Canada, the U.S., Australia, Brazil and the Philippines. The primary parameters - the probability of occurrence and discovery of mineral deposits and the short and long term viability of mineral development - are evaluated and compared on a relative basis by a form of factor analysis. This analysis indicates that of the five countries studied, Canada is second only to the United States in degree of favourability for mineral exploration and development.

Jan 1, 1976

By D. R. McConnell

The seafloor in the US Pacific OCS and EEZ is enriched to varying degrees in critical and economically important minerals such as nickel, manganese, cobalt, copper, zinc, REY (rare earth elements plus yttrium), titanium, vanadium, antimony, gold, and silver. These mineral deposits take the form of polymetallic nodules on the seabed, cobalt rich ferromanganese crusts on seamounts and ridges swept clean of sediment accumulation, and seafloor massive sulfides formed by hydrothermal systems at geologic plate spreading centers and volcanic margins. Each of these mineral deposits form on or near the deep ocean seafloor where water depths are typically 4000 m to 5500 m and on the seamounts and volcanic arcs that rise from these depths. Commercial interest in deep sea mineral deposits and the potential for collecting or mining them began in earnest in the 1970s but has been heightened in the last 20 years as the international framework for developing these minerals in International Waters has matured that has coincided with forecasted rapid rising demand for minerals to supply energy and manufacturing needs for the green economy. Compilation reports published by academia, government, and private companies are reviewed to assemble data and assess the prospects for deep sea marine minerals in the US Pacific OCS and EEZ. Key compilations were made by the Circum-Pacific Council and USGS in the 1980s and 1990s. These, together with recent (2023) efforts by USGS to compile geochemical data from USGS affiliated marine research sampling cruises from the 1980s and 1990s, historical data maintained by NOAA National Centers for Environmental Information (NCEI), and recent publicly disclosed results from ISA contractors are used to inform the known occurrence and prospectivity for polymetallic nodules, cobalt-rich ferromanganese crusts, and seafloor massive sulfides in the US Pacific OCS and EEZ.

Feb 22, 2026

By P. J. Hyde

Cyanide is a significant contributor to the cost of producing gold. Any reduction in consumption that can be achieved through more reliable measurement and/or more efficient management of dosing rates can have a significant financial impact. An automated analyser, by its mechanical nature, is not prone to the variations of human operators, particularly notice­able from shift to shift. Reducing the standard deviation of the measurement (ie, reducing noise ), the automated measurement will give the metallurgist a truer picture of the underlying patterns of usage. The combination of automated analysis with on-line operation and a control loop provides timely information that is efficiently utilised in the management of the plant. Until the release of the Chemtronics On-Line Cyanide Analyser (OTA3000) about 12 months ago, the Australian experience with automated analysers (especially on-line) had been substantially negative. Since its release, the Chemtronics instrument has outperformed both manual titrations and other automated instruments, gaining an enviable reputation for accuracy and reliability in the process. The instrument is built around the technique ofpotentiomet­ric titrations, in which the potential of an indicator electrode is measured as a function of the volume oftitrant that is added to the sample. As the cyanide in the sample is depleted, the potential on the indicator electrode changes rapidly, producing a typical sigmoidal curve. The OTA3000 takes the first differ­ential of the curve, identifies the apex of the peak as the endpoint and reports the result in parts per million of sodium cyanide. The OTA3000 accepts the peak as valid only if it exceeds a certain minimum height. That minimum height is a programma­ble parameter and is used to optimise the relationship between sensitivity and the rejection of spurious peaks. The instrument will track cyanide trends through both positive and negative slopes of any magnitude, but it will provide a warning if it the slope becomes excessive, not because it affects the instrument but because it means that something unusual is occurring in the tanks. There are a limited number of conditions under which the instrument will produce a result of zero. In these cases the OTA3000 holds any output lines at the last valid result while it repeats the titration. This feature was incorporated for reasons of stability in a feedback loop.

Jan 1, 1995

By J. L. Vanderbeek

Investigations have been conducted at Chino Mines Company into the effect that SAG mill recycle material (critical size) exerts on SAG mill throughput and specific energy requirements. Tests were conducted on the laboratory, pilot, and plant scales, to evaluate the merits of alternative treatment options. Removing critical size material from the SAG mill circuit has been shown to improve new feed rates by 34% with a reduction in specific energy (kWh/ton) of 33%. Test results obtained to date are presented.

Jan 1, 1985

By Jens Gutzmer, Helmut Mischo, George Barakos

"It has been nearly eight years since rare-earth elements (REE) became the subject of frontpage headlines. It was when the controversial Chinese export policy for these critical commodities was epitomized in a maritime border dispute with Japan in September 2010 that resulted in the big REE crisis and price spike of 2011 (Barakos et al., 2016c; Mancheri, 2015).The world was dismayed, especially in REE-importing countries such as the United States that was, and still is, totally dependent on Chinese production and exports (Barakos et al, 2016c; Kennedy, 2015). The short-lived alarm initiated a treasure hunt by way of exploration for REE deposits all over the world. The continuously growing demand on the one hand, and the Chinese sovereignty of the REEmarket on the other, led the rest of the world to explore their own REE resources. In just a few years, more than 400 projects were initiated to explore REE deposits outside of China (ERECON, 2015; Goodenough, 2016).The prices of REE, however, dropped rapidly in late 2017 and were in six-year lows, before the 2011 crisis (Barakos, 2017). The viability of even major established producers is being challenged, not to mention the development prospects of potential REEmarket entrants (Barakos et al., 2016b; Rollat et al., 2016). Production cutbacks and industry consolidation in China have impelled REE market experts to forecast that prices have already reached their lowest point and have nowhere to go but up (Adamas, 2015; Roskill 2015). Yet, expectations for increased REE prices are limited and drastic changes are unlikely to happen in the near future, as there is still excess supply in the overall REE market (Barakos, 2017). Nevertheless, the low prices of rare earths are not the only reason that potential producers are struggling to enter the global REE market. Among other parameters, the separation process of the individual elements seems to be the most important factor, as it is technically challenging and expensive to build and to operate."

Jan 8, 2018

By STEVEN J. SCHATZEL, Zoheir Khademian, KAYODE M. AJAYI

The integrity of unconventional shale gas well casings positioned in the abutment pillar of a longwall mine could be jeopardized by longwall-induced deformations. Under such scenarios, the surrounding fracture networks could provide pathways for gas flow into the mine, creating safety concerns. To provide recommendations for developing guidelines that ensure a safe coexistence of longwall mining and unconventional shale gas production, this study uses a discrete fracture network (DFN) model to evaluate the impact of parameters that could affect potential shale gas flow into the mine in the event of a casing breach. These parameters are evaluated using a conceptualized DFN realization that is representative of the fractured zone in the overburden, and the range of parameter variations are within values validated with field measurements.

Mar 1, 2023

By Y. Pan, P. Tukkaraja, R. BHARGAVA, V.V.S. VYTLA, S.J. SRIDHARAN

Panel caving is an underground bulk mining method that uses gravitational force to mine massive, steeply dipping and deep-seated ore deposits at lower operating cost. To control dust and gas emissions entering the production level during the extraction of ore from the draw points in a panel cave, relatively negative pressure is created in the cave by installing an exhaust fan in the exhaust drift located on top of the cave. As caving is a dynamic process, designing an effective ventilation system is challenging; therefore, estimating the airflow resistance offered by the broken rock inside the cave is critical. This study investigates the effect of changes in the bulk porosity of the broken rock on the cave airflow resistance using the computational fluid dynamics (CFD) approach. The results show an inverse relationship between the cave airflow resistance and the bulk cave porosity. The pressure-quantity characteristic curves presented in this paper provide valuable information for sizing and operating an exhaust fan used for a mature panel cave ventilation.

Nov 1, 2022

By Robert A. Jankowski, J. Drew Potts

The Bureau has identified several ventilation techniques and a water spray application for reducing auger mining dust levels. The dust control methods all work by improving air quantity or flow patterns at the face. Section airflow is maximized by reducing air leakage between entries. Sealing stoppings with brushed- on mortar, containing fiberglass additives, reduces leakage. Heading airflow is maximized by properly installing the brattice curtain and keeping the area between the curtain and rib free from obstructions. The brattice curtains should be hung at least 1.7 m (5.5 ft) from the ribs in 7.9 m (26 ft) wide entries and kept less than 4.6 m (15 ft) from the face. A tight curtain seal is created by using the mine air pressure to force the curtain against the timbers, roof and floor of the mine. Using both a blowing curtain and an exhausting curtain will isolate some face workers from dusty air. The Bureau designed, auger clearer spray system, can be used to force heading air across the active face. Laboratory tests indicate that the auger clearer spray system can increase face velocities by more than 0.5 m/sec (100 ft/min), while using less than 0.13 l/sec (2.0 gal/min) of water.

Jan 1, 1989

By Steve Kral

One of the world’s most successful mining shovel manufacturers believes its name is not very well known in North America, particularly in the United States. And there are plans under way to improve on that. Never mind that it is one of the largest mining shovel manufacturers in the world. Or that the mining division has 800 machines in operation worldwide, 100 of them in the United States. And the company currently holds 30% of market share worldwide and 10% in the United States. Forget about the fact that it has already sold more machines world-wide this year than it did during 1995. None of that is good enough. O&K Mining GmbH Dortmund is the mining division of Germany’s giant O&K Orenstein and Koppel. It is one of three divisions of O&K Orenstein and Koppel AG, a US$1.2-billion company. The other two divisions are construction equipment and escalators. The mining division, though, is one of the company’s most successful.

Jan 1, 1996