Search Documents

By Eugie Kabwe

The velocity of detonation (VOD) is a significant property considered when rating an explosive. It may be quantified as a confined or unconfined velocity. The confined velocity is the rate at which the detonation wave propagates through an explosive within a blast hole or any restrained space. The unconfined velocity emanates when an explosive is detonated in the open. However, the confined velocity is more significant as explosives are usually employed under a definite degree of confinement. This paper evaluates the increment of air deck volume and its effect on the VOD. The air gap (air deck) volume is increased stepwise from 10 to 30% of the total blast hole volume by reducing the stemming height in the collar zone. Thereafter, the VOD estimation in the 172-mm-diameter explosive column is conducted using the Dáutriche technique. It is observed that the VOD reduced with the increasing air deck volume and detonation failure is high when 30% of the blast hole volume is replaced with air deck. It is deduced that the increment of the air deck volume has an effect on the attenuation of the steady-state VOD.

By D. J. Sweet, B. Seymour, T. M. Emery, M. Armatys, J. P. Bourgeois, W. Johnson

The Spokane Mining Research Division (SMRD) of the National Institute for Occupational Safety and Health (NIOSH) has partnered with a narrow vein, hard rock underground mine to research the effects of the binder content on the elasticity and post-peak ductility of cemented hydraulic backfill (CHB). This is part of a larger study to enhance the long-term integrity of ground support in underground mines. As mining advances deeper and stresses increase, CHB mix designs will benefit if they can be modified to handle higher levels of strain which are induced by an increased stope closure, typically affected by a reduction in stope width and increased mining depth, or through dynamic loading resulting from a local seismic event. This portion of the research examined the impact of reductions in binder and their impact on Young’s modulus, peak strength, and post-peak ductility.

Mar 2, 2022

By Siddhartha Roy, Hemant Agrawal, Ram Madhab Bhattacharjee, Devi Prasad Mishra

Heat stress in underground coal mines is a major threat to the health and safety of the miners. Hence, managing heat and prediction of heat stress in advance is essential for maintaining a safe, healthy, and productive underground mine environment. In this study, an extensive ventilation survey has been carried out in three different deep and mechanized underground coal mines. The ventilation survey data are used to develop 3D simulation models with the VentSim™ software to predict the conditions that could cause heat stress in underground mine workings. The developed 3D models predicted well the wet-bulb globe temperature (WBGT), a recognized indicator of potential heat stress, with a coefficient of determination (R2) of 0.986, 0.994, and 0.993 for Mine-A, Mine-B, and Mine-C, respectively. Moreover, through 3D modelling, the applications of auxiliary ventilation and spot coolers to reduce the wet-bulb globe temperature (WBGT) for improving the underground workplace environment have been explored. The study demonstrated that auxiliary ventilation and spot coolers can help in significant reduction of heat stress conditions in an underground mine environment. By application of auxiliary ventilation, to increase air volumes, and spot coolers, the WBGT index in mining faces is reduced by 1.2–1.4 °C and 3.9–5.4 °C, respectively. Therefore, it is concluded that the spot coolers are more effective in reducing the heat stress conditions in hot and humid underground mine environments in comparison with auxiliary fan that is used to increase the air volume and velocity. This study opens up a new horizon of 3D simulations for heat stress management in underground mines. The outcome of this study will be useful for the researchers, mine operators, and environmentalists understanding the heat stress contributors and their control in underground mine environment.

May 10, 2023

By E. Bakhtavar

In this paper, problem of short-term production planning for dimension stone quarries was mathematically modeled using a binary integer programming. The model includes an objective function, which was founded as the minimization of the costs due to the total cutting planes of the blocks. This objective may cause to maximization of the net present value (NPV) in dimension stone quarries. During the mathematical modeling the essential constraints are dimension stone quarry capacities and the market demand, block accessibility for the equipment and the reserve constraints. As a base, an optimal size and shape of extractable blocks should be first assigned according to the available extraction technique and the market demand, in order to create a geological block model. Then an economical block model is provided by assignment of a value of ?one? for ore blocks and ?zero? for waste. Maximum profitability and minimum amount of the ore wastage can be gained using this plan and modeling.

Jan 1, 2012

By James A. Pendleton

The Legislature of the State of Colorado adopted House Bill 1223, "The Colorado Surface Coal Mining Reclamation Act" (The State Act), in 1979. This Act provided for the creation of a state regulatory program as accommodated within Public Law 95-87, "The Surface Mining Control and Reclamation Act of 1977" (SMCRA). Section 34-33-121(2)(a) of the Colorado Revised Statutes (CRS) and Section 516(b) of Public Law 95-87, identically require the underground coal mine operator to "Adopt measures consistent with known technology in order to prevent subsidence causing material damage to the extent technologically and economically feasible, maximize mined stability, and maintain the value and reasonably foreseeable use of such surface lands, except in those instances where the mining technology used requires planned subsidence in a predictable and controlled manner..." On July 23, 1980, the Colorado Mined Land Reclamation Board adopted regulations to administer and enforce the State Act. Amendments to the Rules, including the subsidence regulations were adopted by the Board in August of 1981. These regulations require the prediction, monitoring and mitigation of "material damage" caused by subsidence.

Jan 1, 1985

By A. Vien

MOCCA is a Multivariable Optimal Constrained Control Algorithm developed specifically for non-square industrial control applications with practical difficulties such as interactions, time delays, constraints, modelling development, etc. MOCCA consists of an off-line simulation/translation module, for tuning the control parameters, and an on-line module that implements the designed control law. This paper describes an evaluation of MOCCA on the Hemlo grinding circuit which comprises one open circuit ball mill and two closed circuit ball mills in series. In this case a 4x4 unconstrained control problem was considered. The manipulated variables included the fresh ore feed rate and three pump box water additions. The controlled variables were the grinding circuit product particle size and three pump box levels. In this application soft constraints were implemented through control action and control error weighting. The feedforward capability of MOCCA was used to compensate for a measured water flow disturbance to one of the pump boxes. MOCCA performed very well during plant evaluations when compared to the original classical multi-loop control strategy and proved to be quite robust. Perhaps most importantly, the process engineers and plant operators have a high level of comfort both in understanding MOCCA's general operating principles, and with its demonstrated performance.

Jan 1, 1991

By H. Sis

The pressure filtration behavior of dispersed and flocculated alumina slurries at high percent loadings is discussed with an objective to determine the effect of surfactant type and concentration on slurry properties. A high purity alumina powder was used as a model solid. Dispersion of the alumina was controlled by surfactants that are considered to act by electric and steric stabilizers. The effect of both the ionic and nonionic surfactants was investigated. Surface charge measurements of the slurries were carried out by electrokinetic sonic amplitude (ESA) method to understand the mechanisms. The effect of surfactant type and concentration on the kinetics of pressure filtration and final cake properties are discussed.

Jan 1, 1998

By Y. Guan

The dissolution behavior of copper and gold from their pure state and from Au/Cu alloys in cyanide solutions has been investigated using a rotating disc. Oxygen was used as an oxidant. The effect of the composition of the alloys, stirring speed of the disc, concentration of lixiviants and temperature on the overall dissolution kinetics has been studied. Gold/copper alloys of three compositions were used in this study. The atomic percent of gold in these alloys was 75, 50 and 25, respectively. The dissolution behavior of these three alloys was compared with that of pure gold and of copper under the same chemical conditions. In general, the dissolution of copper and gold from alloys is partially controlled by surface chemical reaction and largely by mass transfer.

Jan 1, 1992

By Dan Plazak

The authors are to be congratulated for presenting a simple and practical tool for quick estimates of ground water flow rates. At the risk of detracting from the simplicity of the method, I would like to suggest a slight refinement to the equation as presented. As the authors noted, the Jacob-Lohman equation (1952) assumes confined-aquifer conditions. To use confined-aquifer equations in water-table aquifers, Jacob (1963) presented a correction to convert water-table aquifer drawdowns [ ] to equivalent confinedaquifer drawdowns [ ]:

Jan 1, 1994

"In this review, the sintering process is first described and analyzed to identify the key factors affecting the structure and quality of iron ore sinter. Under fixed sintering conditions, the granulation efficiency, nucleus stability and primary sinter melt volume and properties of the iron ore are considered to have significant influence on the sinter structure and quality. Discussion is then focused on the effects of the chemical, physical and mineralogical characteristics of the iron ore on these key factors, and the consequences for sinter quality.IntroductionSintering is the most economic and widely used agglomeration process to prepare iron ore fines for blastfurnace use. In modern blast furnaces, particularly in East Asia, iron ore sinter typically constitutes more than 70% of blast-furnace ferrous feed. High sinter quality and efficient sinter production are thus required both to withstand extreme operating conditions and maintain the productivity of modern blast furnaces. At the same time, due to the increasing depletion of high-grade iron ore resources from large deposits, iron ore producers are moving toward developing an increasing number of deposits of much smaller sizes to maintain current production levels. It is therefore imperative for iron ore producers to develop long-term strategies to maintain the quality and consistency of the iron ore fines they are producing while exploiting these smaller, complex deposits. The iron grade, gangue minerals present, overall mineralogy as well as physical characteristics of iron ore fines being mined from these different deposits vary considerably. Overall, ores now have highly complex mineralogy, are becoming more porous and friable, and contain increasing amounts of gangue minerals, which will have important implications for the sintering process and sinter quality.Blending is one of the most effective options being explored by iron ore producers to deal with multiple small complex deposits. This allows the iron ore producers to reduce the number of products and take full advantage of the unique characteristics of each individual deposit to achieve long-term product consistency while increasing production. Blending is also a common practice in sinter plants as it is almost impossible to produce from one single ore a high-performance sinter mixture with the required processing characteristics. A typical sinter mixture used in Japanese steel mills (Nakano and Okazaki, 2007; Matsumura et al., 2013) often contains five or more ores to achieve balanced sinter quality and productivity with relatively low cost of raw materials."

Jan 1, 2015

By George Hufford

An investigation is made into the applicability of queueing theory to simulating the operation of a large open pit copper mine in the southwestern United States. Actual data from a working mine was used to construct curves for truck loading time, haulage and return time, and dumping times. Known results of investigations of queueing models (Koenigsberg - 1958, Gordon and Newell - 1967, Cabera and Maher - 1973) were used to simulate the actual operation. These did not give acceptable results so commonly used probability distributions were fitted to the actual data. A large computer program known as Q-GERT was used with the various parameters obtained from fitting the curves. Kolmogorov- Smirnov tests were run that showed that this was not satisfactory either. Finally, Q-GERT was used with the actual data from the mine. An appropriate correction factor is then found to apply to the exponential probability distributions tested previously and satisfactory results are obtained.

Jan 1, 1981

By S. A. McGhee

Introduction ASARCO's Ray Operations include an open-pit copper mine in the Mineral Creek Mining District of Pinel County. The district is located in east central Arizona, 132 km (82 miles) southeast of Phoenix, AZ, and 126 km (78 miles) north of Tucson, AZ. The mine lies 8 km (5 miles) north of the Gila River in Mineral Creek Valley, between the Tortilla Mountains to the west and the Dripping Springs Range to the east. The rich copper deposits of the Mineral Creek mining district were first noted by a US Army Officer in 1847. The Ray Copper Company was the first major operation in the area. The company was named after the Ray mining claim, which was one of the earliest recorded claims. After decades of sporadic and unsuccessful mining ventures, the Ray Consolidated Mining Company was formed in 1910. The company introduced one of the first successful block caving operations in the world. In 1933, the Kennecott Copper Corporation acquired the Ray Consolidated Mining Company and continued operation of the mine under the same name until 1943, when the property was renamed the Ray Mines Division of Kennecott. Underground mining continued until 1955, when the mine was converted to an open pit operation. In November 1986, ASARCO Inc. purchased the Ray Mines Division and related facilities from Kennecott. The purchase also included the Hayden concentrator and the Ray Smelter, located approximately 32 km (20 miles) from the Ray Mine. This paper summarizes the 54,400 tpd (60,000 stpd) in-pit crusher and overland-conveying system and the 24,200 tpd (30.000 stpd) copper SAG concentrator and tailings disposal system constructed at ASARCO's Ray Complex - Ray Operations. General description of facilities The Ray concentrator includes a sulfide SAG concentrator, a "relocatable" in-pit primary-crushing plant and overland-conveyor system, a concentrator tailings-disposal system and plant ancillary facilities, The major elements of the project include: • A relocatable Fuller-Traylor in-pit 1524-mm (60-in) x 2261-mm (89-in) primary gyratory crusher at the 442 m (1450 ft) mine elevation. The crushing plant has a nominal capacity of 54,400 tpd (60,000 stpd) of sulfide ore. • A 1524-mm (60-in) wide x 1253-m (4110-ft) long overland belt conveyor, which runs from the in-pit crushing facility to a transfer station serving both the Ray Concentrator and the existing Hayden concentrator railroad load-out facility. • A 1524-mm (60-in) wide x 152-m (500-ft) long stackerbelt conveyor, which delivers a nominal 27,200 tpd (30,000 stpd) of ore from the transfer station to a 23,600 t (26,000 st) live-capacity coarse-ore stockpile serving the Ray Concentrator. • A nominal 27,200-tpd (30,000-stpd) concentrator, including semiautogenous grinding, flotation, copper concentrate filtration and associated plant ancillary facilities. • A tailings disposal system. Flotation tailings are pumped from the Ray Concentrator to a 122-m (400-ft) diam. thickener, located 4.8 km (3 miles) southeast of the Ray Concentrator site. The thickener overflow is pumped to two 76.2-m (250-ft.) diam. concrete process-water reservoirs. The thickener underflow, at 45% solids, is pumped to a new tailings disposal site located at Elder Gulch. • An HDPE-lined temporary-containment area to collect material from Ray Concentrator plant upsets and local storm-water run-off from a 100-year, 24-hour rain event. •A reclaim-water system from the Elder Gulch tailing pond area to the Ray Concentrator. • A 610-mm (24-in.) diam. x 31.9-km (19.2 mile) long fresh-water pipeline from the Hayden fresh-water-well field system to the Ray Concentrator. The overall process design criteria for the new Ray Concentrator is based on a nominal throughput of 27,200 tpd (30,000 stpd) of ore at 90% plant availability. However, based on the maximum performance capacity of the installed grinding equipment, it may be possible to achieve a sustained operating level in excess of 36,300 tpd (40,000 stpd) when processing soft ores. The balance of this paper will cover the major process systems including:

Jan 1, 1995

By Roscoe W. Stensrud

The Marcona Corporation was established in 1965 to consolidate the ownership and management of the Marcona group operations. This company, with headquarters in San Francisco, has the following principal operating subsidiaries: Marcona Mining Company, formed in 1953, conducts iron ore mining, beneficiation and pelletizing operations in Peru. Cia. San Juan S.A., Panama, which contracts for sale and delivery of iron ore from the Marcona operation in Peru and from Mount Goldsworthy in Western Australia. Sari Juan Carriers, Ltd., a subsidiary of Cia. San Juan which owns and charters vessels for the bulk ocean transportation of iron ore, petroleum products, coking coal, slurry, salt and other commodities.

Jan 1, 1968

By T. S. Lundström, B. D. Marjavaara, I. A. S. Larsson

"The flow field in a rotary kiln, used in an iron ore pelletizing process, was investigated using a three-dimensional computational fluid dynamics model. The model is isothermal, downscaled and simplified. The objective was to examine the possibility of capturing the unsteady motion of the flame seen in the real kiln. The results from the simulations were compared with recorded images of the real process. The results demonstrate the possibility of quickly getting an overview of the flow field in the kiln. The main, unsteady behavior of the flame was captured. The model may be used as a tool in the ongoing work of improving and optimizing the pelletizing process.IntroductionThe pelletizing process, in which the crude iron ore from a mine is upgraded into pellets, is a process involving large amounts of hot air flowing in complex geometries. Flow control is a crucial factor in this process to maintain high pellet quality. The rotary kiln is one of the last steps in the pelletizing process, and this is where the pellets are sintered to increase their strength and metallurgical properties. The kiln burner produces a flame that supplies the entire pelletizing process with the necessary heat.Kiln burner flames are large diffusion flames arising from a jet of fuel from the burner issuing into a concentric confining cylinder with a surrounding coflow of air, called secondary air. To enable combustion, the secondary air needs to be entrained into the fuel jet. This mixing of the fuel and air is the slowest step in the combustion process and therefore affects the efficiency of the combustion. The rate of entrainment depends on the momentum ratio between the burner jet and secondary air. The higher the momentum ratio, the faster the entrainment rate and, consequently, the faster is the fuel/air mixing.The kiln of interest in this study differs from kilns used in other industrial processes in both geometry and operating conditions. A distinguishing feature is the large amount of secondary air being induced through the kiln hood and then transported to earlier stages in the process as air or exhaust gas. The secondary air therefore has a substantial momentum, implying that the resulting flow field has a significant impact on the mixing and combustion process in general and the flame shape and stability as well as combustion efficiency in particular. A systematic study of the factors influencing the dynamics of the flow field in the kiln, neglecting the combustion, is therefore justified."

Jan 1, 2016

By John S. Harper

Can the mining industry in the United States accept the change and challenge of the "Now Generation" of entirely new high-performance automated transportation systems? Good Question! While there has been some revolutionary new thinking and product testing in mining, none has taken place in transportation of ore and waste. With one notable exception - DASHAVEYOR - not a single really new and 'unconventional' system has even been tried on a small scale in the hardrock mines in our country. Admittedly, U.S. equipment manufacturers share the responsibility for the slow progress in mine transportation systems in our country, since they have provided very litte leadership in design innovation or education. First, let me give you my definition of what is meant by the term "Advanced Transportation Systems". Then I will describe and compare such systems, emphasizing the strong and weak features of each as they apply to vertical and horizontal haulage. I will conclude by establishing the principal requirements for implementation of these types of systems in the mining industry in the United States.

Jan 1, 1969

By Randy Reed, Barbara J. Arnold

Respirable crystalline silica poses a significant health risk, with the American Lung Association estimating that 2.3 million workers are exposed to silica in the workplace. This includes mine workers as well as those in many other industries. Reducing dust formation is sometimes not possible so other methods to reduce exposure are critical. These methods include the use of surfactants to reduce airborne dust particles. However, it is the proper selection and application of surfactants that leads to reduced dust exposure. A discussion of how surfactants work, especially for silica dust, leads to guidance for surfactant selection followed by a review of technologies for their application.

Feb 1, 2024

By A. E. Koski

This paper describes the implementation of specialized software in mine planning at the Cleveland-Cliffs' managed Empire Mine on Michigan's Marquette Iron Range. The application puts together years of mining experience on the eastern end of the Marquette Range beginning in the early 1960's. The Empire Mine, in its thirty-fifth year of production, uses the software to model a complex and highly variable low grade magnetite ore body, capturing the economics of mining and processing to the final product. With special attention given to geostatistical methods, the software is used for all geologic modeling, ore reserve estimation, ore control, pit design and short and long range planning.

Jan 1, 1999

By R. J. Pruett

Selective flocculation enables the production of high-brightness kaolin products from kaolin ore once considered too poor in quality for beneficiation into paper-coating pigments. Anatase, Ti(1-X)FeXO2, with X = 0 to 0.05, is a common iron-bearing impurity in sedimentary kaolin that can be unresponsive to kaolin beneficiation processes, such as magnetic separation, due to its extremely fine particle size (<0.3 µm), or chemical bleaching, because of its chemical stability. Described here are selective flocculation technologies that separate anatase by flocculating anatase or flocculating kaolinite from dispersed slurries. Applying the advances in the chemical and mechanical dispersion of ultrafine particles and the selective aggregation of kaolinite or anatase particles have resulted in the selective flocculation processes practiced today that have increased process recoveries from those technologies practiced beginning in the 1960s.

Feb 1, 2012

By J. R. Koehler

Yield pillar-based gate road designs oftentimes fail to provide mine operators with adequate ground control because of the unknowing misemployment of "critically" sized pillars. A "critical" pillar is one that is too large to either yield nonviolently or yield before the roof and floor sustain permanent damage, but is too small to support full abutment loads. To demonstrate the critical pillar concept, a field study of a tapering gate road was conducted by the U.S. Bureau of Mines at the Sunnyside Coal Mines, Sunnyside, UT. Extreme pillar stresses and associated coal bumps characterize the response to first panel mining of a 16.8-m wide critical design. Significantly lower pillar stresses, early yielding of the pillar and adjacent panel rib, and an absence of coal bumps suggest that a narrower 12.2-m-wide design more closely approaches proper yield pillar dimensions. Probehole drilling of several 1 O.6-m-wide pillars revealed low stress levels and substantial pillar and panel rib yielding prior to abutment onset, indicating a properly functioning yield pillar design.

Jan 1, 1995

By R. Gray

"Experience from Australia has identified what is referred to as non-conventional surface subsidence behaviour. This occurs under irregular surface topography, resulting in valley closure, valley floor uplift or “upsidence”, and far-field horizontal movements – even occurring beyond conventional “angle of draw” limits. This paper discusses such behaviour recently observed in Pennsylvania and focuses on the 2005 case of Duke Lake Dam in Ryerson Station State Park. In July 2005, there was a significant increase in water leakage through a number of growing cracks in the dam leading to the dam being breached to avoid an uncontrolled failure. An underground longwall mine was located approximately 900ft to the north, mining at depths of 330 – 720ft. Investigations (including a subsequent ground movement monitoring program) found a range of evidence in the vicinity suggesting that valley closure and far-field horizontal movements may have occurred resulting from the adjacent mining. The paper discusses the phenomenon of non-conventional subsidence behaviour and the Ryerson State Park case study, including an assessment of mining, geology and subsidence impacts and suggested ground behavioural mechanisms. INTRODUCTION Non-Conventional Subsidence The conventional understanding of coal mine subsidence on which most current subsidence understanding and prediction techniques are based, includes the concept of angle of draw which effectively limits the lateral extent of subsidence effects and impacts. Within this zone – above and marginally beyond the boundary of mining – downward vertical subsidence is the dominant component, together with localised horizontal movements towards the mined region, with related tilts and strains. However, more recent experience from Australia over the last two or three decades has identified what is referred to as non-conventional surface subsidence behaviour. This is found to occur in areas of irregular surface topography or variable terrain, and is characterised by phenomena such as valley closure, valley floor uplift or upsidence, and far-field horizontal movements, all of which can occur beyond the conventional angle of draw limits. NSW Department of Planning (2008) defined the conditions for both conventional and non-conventional subsidence behaviour as follows: “The conventional or general model of surface subsidence, which finds worldwide acceptance, is based on assuming the following site conditions:"

Jan 1, 2015