Search Documents

By Malcolm Wills

Hedges Gold Pty. Ltd. mines and processes a lateritic gold orebody approximately 120 km south east of Perth in the Darling plateau. The operation is approximately 26 km from the town of Boddington and 31 km from the town of Dwellingup. Hedges operates under The Western Australian Environmental Protection Act, Licence Number 3183. Presently, nine Limitations and Conditions are applicable to the tailings dam. These conditions apply to maximum discharge/disposal quantity permitted. Hedges mine is located in state Forest within the eastern, low rainfall section of the Darling Range and within the waler catchment area of the Murray River. Ore is carted by 120 tonne haulpacks to the plant. The plant and tailings dam is on private farm land some six kms from the mine.

Jan 1, 1992

By HASSAN E. EL-SHALL, AYMAN A. EL-MIDANY, KERRI-ANN A. HUE

Modifying the hydrophobicity of clay is necessary to accommodate large mycotoxin molecules such as zearalenone (ZEN). In this study, tricaprylmethylammonium (TCMA) chloride and common corn oil were used to modify clay. The results indicate that more than 90 percent of ZEN could be removed using clays modified by TCMA and corn oil at acidic and neutral pH due to the expansion of intergallery spacing as a result of TCMA surfactant intercalation within the clay-forming layers. The removal percentage depends on the pH and amount of clay used. Complete removal can be achieved at acidic pH and small clay amount.

By R. A. Williams

Surface and electrochemical techniques have been used to describe the surface chemistry of ferrosilicon powders, as a function of pH and electrochemical potential, for conditions typical of operating DHS plants. The practical consequences on the likely corrosion behaviour and associated electro- kinetic particle-particle interactions (which affect stability to sedimentation) in the suspension, are discussed.

Jan 1, 1987

By J. C. Cawley

Improvements in today's maintenance practices are mandatory as more complex and productive machines evolve in the mining industry. By keeping machine reliability high, through improved maintenance procedures, overall mining costs can be reduced. The Bureau of Mines is investigating diagnostic maintenance systems for underground mining machinery. A hydraulic expert diagnostic system and an electric motor predictive diagnostic system have been designed and installed on a Joy 16CM continuous miner. An electrical diagnostic system has been designed and installed on a Joy 14CM continuous miner. Each system is functionally described and the relative merits of expert diagnostic systems versus algorithmic diagnostic systems are discussed.

Jan 1, 1991

By R. D. Begley, A. W. Khair

This paper presents an assessment of modeling techniques in predicting subsidence over longwall areas. Extensive instrumentation has been made, both at the surface and subsurface, at three longwall mines in northern West Virginia. Ground movements were monitored during a three- year period until subsidence ceased in these areas. A comparative analysis of empirical subsidence prediction techniques including graphical (NCB), profile function, influence functions (USBM, Bals', Knothe's, and zone area) will he presented. A brief geologic and topographic description of each site, along with the instrumentation and monitoring program, will also he presented.

Jan 1, 1990

By Andy Ingriselli, Andrew Famiglietti, John Westland, Greg Landry

Atlas Dewatering was contracted to install and maintain a groundwater control system for the new Bessarion Subway Station and the Tail Track Structure on the Toronto Transit Commission’s new Sheppard Subway Line. Atlas met the challenges presented by the project by closely reviewing the contract documentation provided by the Program Geotechnical Consultant, Golder Associates and by working with the general contractors, Bondfield Construction Company and PCL Constructors Eastern, inc., throughout the duration of both projects. In addition to concerns about soil loss, excessive settlement and seepage, the consultant was concerned about spreading hydrocarbon-contaminated groundwater between the two aquifers present at the Bessarion Station site. By installing a system of multi-level vacuum eductor wells around the perimeter of the excavation, Atlas was not only able to provide a dry excavation for construction, but, due to a unique well design was also able to prevent cross-contamination of the aquifers.

Jan 1, 2001

By L. B. Hales

The advent of the process control computer with its capabilities of monitoring, storage, and real-time control has revolutionized control technology in the mineral industry. Initial efforts to introduce the computer into process control began in the early 1960's. However, it wasn't until the last decade with the introduction of integrated circuits and minicomputers that truly successful applications became visible. Computer hardware and real-time operating software have improved to the point that they rarely provide major problems in the implementation of successful control systems. At this time the most prevalent problems and obstacles affecting the successful implementation of a control system are as follows: (1) reliable and representative sampling systems; (2) rugged and reliable process sensors; (3) the availability of well-defined control strategies; (4) the willingness of plant management to provide the continuous support necessary to acquire and/or train appropriate personnel in the operation and maintenance of advanced control systems. Discussion of these problems and of the instrumentation required for the successful application of computers in minerals processing plants follows. In order to enhance this discussion the remainder of this subsection is broken up into individual mineral processing categories.

Jan 1, 1979

By Byron C. Hardinge, E. R. Palowitch, Albert W. Deurbrouck, David J. Akers, Edward R. Torak

During 1983, 42.2% of the 686.0 (624.3 Mt) million tons of coal reported, 289.6 (263.5 Mt) million tons were mechanically cleaned, of which 107 (97.4 Mt) million tons were cleaned by dense media (magnetite and sand) processes.' The percentage of bituminous coal and lignite cleaned mechanically by dense medium processes increased from 7 to 38% between 1938 and 1983. The Electric Power Research Institute estimates that 150 million tons (137 Mt) of coal were cleaned by heavy-media processes in 1986, and that this number may increase to 265 million tons (241 Mt) by 1990.2 Dense medium separations include those coal preparation processes that clean raw coal by immersing it in a fluid having a density intermediate between clean coal and reject. As there is a general correlation between ash content and specific gravity, it is possible to achieve the required degree of removal of ash-forming impurities from a raw coal by regulating the specific gravity of the separating fluid. Dense medium processes generally offer the following advantages over other coal cleaning processes: • Ability to make sharp separations at any specific gravity within the range normally required even in the presence of high percentages of raw coal whose specific gravity is near the specific gravity of separation. • Ability to maintain a separating gravity that can be controlled within + 0.005 sp gr units. • Ability to handle a wide range of coal sizes. • Ability to change specific gravity of separation to meet varying market requirements. • Ability to handle fluctuations in feed, in terms of both quantity and quality. Unfortunately, dense medium processes can have the following disadvantages: • Relatively high capital costs caused primarily by the need for equipment to collect and recycle the medium. Relatively high operating costs caused primarily by operation of medium recycle equipment and loss of medium.

Jan 1, 1991

By Georgios Kafantaris, Carsten Bonde, Nataša Katic

Within the investigation works for the Copenhagen Cityring metro, Geo/CMT have carried out 90 geotechnical boreholes. Together with the previously available investigation, this resulted in more than 15 km of vertical drillings and several thousands of laboratory tests. The design is made for 17 stations, four shafts and two parallel 16 km long tunnels. The geotechnical investigation and design have been carried out in several stages comprising appropriate refinement of structural design and design of excavation operations, including TBM break-in and launching operations at each station shaft. Acceptance of the solution and / or refinement of the investigation and design schedule in the next stage were based on the geological conditions, area availability at surface level, planning and cost-control criteria. The applied recursive design refinement is presented herein with an example of the Østersøgade shaft location.

Jan 1, 2016

By Clayton J. Parr, Northcutt Ely

Mining law is essentially a branch of the law of real property. It concerns acquisition of property for extracting contained minerals, and the rights, privileges and duties that fall upon the holder thereof once the rights are acquired Accordingly, this section focuses on the procedures to be followed in acquiring state. federal and private lands, and defines briefly the nature of the rights obtained. The mining laws of Canada and Mexico are summarized, and the related subjects of minerals taxation and governmental regulation are discussed briefly. This section is not intended to be the basis for legal decisions. Rather, its purpose is to provide the engineer with an understanding of basic principles and procedures. For a detailed treatise of mining law, reference can be made to The American Law o] Mining, a five-volume set edited by the Rocky Mountain Mineral Law Foundation. The law changes constantly, especially that based on federal and state statutes, and the reader is cautioned to be alert for subsequent modifications of statutes, regulations and case law. 2.1-PRELIMINARY LAND-STATUS CHECK Often, after completion of area reconnaissance, or perhaps after receipt of a submittal, a specific more localized target area will become of interest. Usually, an intensive exploration program comprising detailed surface mapping, sampling, geophysical prospecting and drilling will be required before the mineral potential of the ground can be properly evaluated. Before an investment of this magnitude is made, however, it is advisable to obtain rights to mine ore from the property. Otherwise, knowledge of the exploration activity might greatly inflate land values, or speculators or competing mining concerns might step in. Hence, as a general rule, a land-acquisition program should be undertaken before an intensive exploration project is begun. The first step in such a program is to make a land-status check to determine whether the subject lands are available and, if so, from whom they can be obtained and by what means. 2.1.1-BUREAU OF LAND MANAGEMENT RECORDS In those states which contain large areas of federal land, basically (he western states, the primary informational source is the records of the Bureau of Land Management. These may t)e examined at the land office having jurisdiction over federal lands in the area of interest. The records for Montana and North and South Dakota are kept at the Billings (Mont ) land office; Wyoming, Nebraska and Kansas, Cliejenne, Wyo.; New Mexico, Oklahoma and Texas, Santa Fe, N M ; northern Alaska, Fairbanks, and southern, Anchorage; Utah, Salt Lake City; Nevada, Reno; Arizona, Phoenix; Colorado, Denver. There are two land offices in California, at Sacramento and Los Angeles Records for other states are kept in Washington, D C. at the office of the Director, Bureau of Land Management.

Jan 1, 1973

By F. G. Heivilin

There will be 3 billion people moving into cities by 2050. Permitting is both the biggest obstacle and the biggest opportunity for mining. The problem is not if we have the right minerals, but how we can permit and produce it in a ?Sustainable? manner. A ?Permit? and a ?Sustainable Development Plan? may soon be the same thing. How do we produce the minerals we need with: 1. The lowest possible carbon footprint. 2. Social license from community outreach by being a catalyst and not a problem in a ?Green World.? 3. Enhanced water supply during all stages of production. 4. Meeting requirements of our customers for service, quality, & cost. How important is it to have a complete ?Sustainable Development Program?? First, no plan is complete!!! It is a work in progress subject to continuous improvement. We need to work together to get the results we want. The goal of the world communities is to become carbon neutral by 2050. What is the mining community?s goal? Do we have one???? When a Clorox, Colgate Palmolive, Wal-Mart, Toyota, or Caterpillar buys a product, what are your chances of getting an order without a good program in place? The answer is it will be difficult or impossible shortly and you will be requiring the same thing with your suppliers. This is an opportunity if you are in the lead and it soon will be a necessity for most mining and processing companies requiring much extra effort to catch up. For some mines it was a necessity to get most of the SD plan to get permitted. The number of companies in the extractive industries with a full Sustainable Development Programs is expanding rapidly as shareholder demands for transparency continue to grow.

Feb 27, 2013

By B. T. Stanley

Traditional methods of creating a water tight shaft liner involve the use of segmented or welded steel. When shafts are located in ground that exhibits extremely difficult conditions of high water inflow and hydraulic pressure, composite liners are often combined with ground freezing during construction. The authors were searching for a cost effective and more flexible solution to hydrostatic liners design than the traditional concrete/steel composite design used so far. Searching through new technologies developed for tunneling applications, sprayed on membranes systems seemed very promising but were not developed for the specific circumstances encountered in shaft sinking applications where ground freezing is involved. Even though freezing is a very effective technique, it creates adverse temperature conditions for the application of spray on membranes. In addition, application and hydrating cure times for those membranes products ranged between six to twenty-four hours under ideal conditions (usually temperatures well above freezing point), which eliminated them from consideration in a shaft sinking cycle. While researching different spray on membrane materials, it was discovered that Stirling Lloyd Polychem Ltd. has developed and proven a different membrane material for waterproofing liners in different tunneling applications. The characteristics of the membrane exceeds the pressure parameters encountered in frozen shaft sinking operations, and the chemical cure times were reduced to one hour per layer which worked well into the shaft sinking cycle times. More over their system included a quality control procedure that allowed insuring integrity of the membrane at application time, a very desirable feature for shaft liner construction. However, the frozen rock surface still presented an unknown in the cure time and stability equation. As all membrane products a shotcrete substrate is usually required prior to application. The hypothesis used by the author was to use this shotcrete layer, not only as a substrate, but also as a thermal insulation against the frozen rock and the membrane during both application and curing time. The authors knew from experience that shotcrete could be applied successfully over frozen rock. But the shotcrete temperature curve over time was unknown and no information were found in the available literature. Testing was required to determine whether a suitable mix of shotcrete could be applied to the frozen shaft wall to provide enough heat of hydration for a suitable period of time to create conditions suitable for membrane application and curing.

Jan 1, 2012

By Hesam Dehghani, Farid Alimohammadnia, Nima Babanouri, Mokhtar Kalhori

In open-pit mining, blasting pattern design is performed to achieve a desired degree of fragmentation for loading, hauling, and crushing operations. Inappropriate fragmentation of rock will result in numerous problems such as incurring extra costs for secondary blasting, production interruption, etc. Wetness of the blast holes is one of the most important factors, which can cause the inappropriate rock fragmentation. Lowering ambient temperature in the vicinity of the explosion, the presence of water in the hole adversely affects the quality of the explosive while dissipating part of the explosion energy, ending up with inappropriate fragmentation problems. In the present research, in order to study blast-induced fragmentation conditions in Baba-Ali Iron Ore Mine, three scenarios were considered: explosion of ammonium nitrate with fuel oil (ANFO) in dry hole, explosion of ANFO in wet hole, and explosion of the emulsion in wet hole. For this purpose LS-DYNA, a numerical simulation code was used. Results of the present research showed that, compared to the explosion of ANFO in wet hole, the explosion of the emulsion produced more uniform distribution of fragment size, while the explosion of ANFO in dry hole resulted in fewer large fragments.

By K. L. Myers, R. Espell, C. Deringer

Construction of the AA Pad reclamation was completed in the fall of 2000. Seeding of the ET cover began in the late fall of 2000 and continued through May of 2001. On Saturday afternoon, June 1, 2002, a large, very localized thunderstorm struck the reclaimed AA Pad site. Eyewitnesses present at the time described a dark storm cloud parked above the site for less than half an hour. Average rainfall intensity was measured to be 122 mm (4.8 inches) per hour and peak rainfall intensity was estimated to be 213 mm (8.4 inches) to 259 mm(10.2 inches) per hour. At the time of the storm, the construction was less than two (2) years old and the vegetation had only a single season of growth. The entire period from the end of construction until the date of the storm was a drought period with below normal precipitation. Other than a few small snowmelt events, there was no precipitation event large enough to produce any significant flow in the channel network. Therefore, the very first significant runoff event was the extreme event of June 1, 2002. The storm essentially represents a large-scale field test of the design concepts used at the AA Pad site. Shortly after the storm, data was collected and analyzed with the intent of learning as much as possible about the performance of the cover system design with the expectation that the newly acquired knowledge might be utilized in future designs to further improve the performance of similar cover systems during extreme events.

Jan 1, 2003

By Wern-ping N. Chen

Pressure tunnel includes water-supply tunnels and tunnels for hydroelectrical power plants. Their design principles are different from those of water/wastewater/conveyance and transportation tunnels. Though theoretical pressure tunnel design guidelines exist, a comprehensive guide to summarize these guidelines to facilitate the planning and design of a pressure tunnel program is lacking. The purpose of this paper is to fulfill this need. It first provides key pressure tunnel design concepts in hard rock environment; then, it illustrates associated final lining design principles, including the design of un-reinforced concrete lining, steel lining, and reinforced concrete lining. Design diagrams and a flowchart for the reinforced concrete lining design are provided.

Dec 1, 2022

By J. C. Judd

The U.S. Department of the Interior, Bureau of Mines investigated solvent extraction methods for recovering gallium from filtrates produced from sulfuric acid leaching of hydrometallurgical zinc residues. These filtrates typically had pH values of 0 to 0.5, too high an acid content for effective gallium recovery by traditional extractants. Of the nine extractants studied in batch tests, 0.3M octyl phenyl acid phosphate (OPAP) in a kerosene diluent was the most effective extractant for gallium recovery, extracting up to 99.9 pct of the gallium. This high extraction was possible when the iron in solution was maintained in the reduced ferrous state. Batch tests also showed that a 1.5M-H2SO4 strip liquor recovered 98 pct of the gallium from the loaded OPAP. A continuous solvent extraction system was designed and operated based on McCabe-Thiele analyses of equilibrium loading and stripping isotherms. When 12 L of leach filtrate containing 0.32 giL Ga and 20 giL Fe were pumped through the system in 32 hr, results showed that 95 pct of the gallium was extracted in four stages at an A:O ratio of 1:1. Stripping the loaded solvent with a 1.5M-H2S04 liquor recovered 94 pct of the gallium in four stages at an A:O ratio of 1:4. A two-stage, 50-pct-phosphoric acid strip successfully removed ferric iron from the OPAP, allowing high gallium extractions to be maintained.

Jan 1, 1990

By Brain W. Lawrence

Sublevel stoping generally is a large-scale open stoping method. It sometimes is referred to as long-hole or blasthole stoping. This method usually is applied to strong ore bodies that require minimal support and are surrounded by strong country rock. The ore body should be fairly regular in shape and well-defined. The dip of the footwall normally should be sufficient to allow broken ore to gravitate freely, although the method has been adapted successfully to mine some of the flatter ore bodies. Sublevel stoping is not dependent on the width of the ore body. Widths of less than 6 m (20 ft), however, make the utilization of long-hole drilling techniques more difficult. The main criteria for sublevel open stoping are competent ore and stable host rock, regular ore boundaries, and a footwall dip that exceeds the angle of repose of broken ore. Basically, the method entails providing access to the ore body at various subintervals between the main haul- age levels in order to drill and blast the intervening ore. Stope drilling is carried out from drilling drifts on the sublevels, and the ore is blasted in slices towards an open face, which generally is vertical on the downholes and may be inclined towards the open face for the up holes. The blasted ore gravitates to the bottom of the stope and is collqcted through drawpoints. Fig. 1 illustrates a typical sublevel stoping mine. The method requires extensive ore body development with relatively high capital expenditures. How- ever, much of the development is in ore, and production costs are comparatively low. Productivity rates are in the 13.6 to 27.2 t (15 to 30 st)/manshift range. The drilling, blasting, and loading operations are performed independently, and equipment utilization is high. Large outputs can be obtained with few units and limited personnel. Dilution with waste rock may occur if ore boundaries are irregular or if caving occurs, but 100% of the ore within the stope usually is recovered. Pillar recovery sometimes is a problem. It is at this point that most of the waste dilution occurs. At the time data was gathered for this report (1973), the sublevel open stoping method was used by more than 21% of the metallic ore mines in the US (9 out of 42 mines producing 1088 + t/day (1200 + stpd) and provided more than 12% of the total metallic ore production from these mines. DEVELOPMENT Access to a sublevel open stope mine is gained by a slope or shaft that is normally sunk in the footwall of the ore zone, away from any possible effects from blasting or other production operations in the stoping process. Main level interval is selected and usually varies from 45.7 to 121.9 m (150 to 400 ft), depending on the vertical extent of the ore body, the number of drawpoints required to maintain output, and the eventual stope height. The main haulage drifts are located at the bottom of the stope horizon, either directly in ore or in the footwall, with access crosscuts at intervals. Raises are driven up through the ore to connect to the level above and provide access and ventilation to the sublevel drilling drifts, which are driven horizontally in the ore for the length of the stope. Depending on the drawpoint system to be used, the stope is either undercut by a raise-and-cone system, from a scram or slusher drift, or simply provided with a drilling drift from which access is made at intervals to the main haulage level. A raise driven either at the end or in the middle of the stope (if stope access is from both ends) provides a start for opening up a vertical slot across the stope to establish a free or open face for long-hole drilling and blasting. Sublevel stoping has proved to be a relatively safe and economical system.

Jan 1, 1982

By Eugene R. Palowitch, Albert W. Deurbrouck, Thomas H. Parrsons

INTRODUCTION Hydraulic concentrators utilize the physical characteristics-size, shape, and specific gravity-of particles suspended in a fluid medium to effect a concentration of desired quality. Fine-coal concentrators include generally those devices which are used to clean roughly 3/4, in. (9.5 mm) top-size coals. While this size designation is somewhat arbitrary, it is consistent with current practice although some fine- coal concentrators can treat coarser coals effectively. A variety of devices have been and are currently being used to wash fine coals and include: dense media cyclones, wet concentrating tables, hydrocyclones, jigs, spirals, launders, and upward-current classifiers. As launders and upward-current classifiers have been replaced by more efficient devices, they no longer warrant consideration as fine-coal washers. And as fine-coal jigs were addressed with the Baum jig under Part 1, Section 2, and heavy media cyclones and hydrocyclones were addressed under Part 2, Section 1, of this Chapter, only the wet concentrating table and the spiral concentrator will be discussed here. WET CONCENTRATING TABLES History The current wet concentrating table evolved from continuous belt concentrators which utilized a flowing film of water to recover heavy metals. In these devices the heavier concentrate moved up the inclined plane of the belt while the lighter impurities were washed away by water flowing down the belt. The natural outgrowth of the continuous belt concentrator was the vanner, a vibrating endless belt which was first developed about 1860 by Hartwig. Later models of the vanner, such as the Frue, incorporated oscillation in a plane transverse to the direction of the water current. Excellent descriptions of these washers are found in The Cleaning of Coal, by Chapman and Mott.80 Further development of tables included the circular stationary table (Linkenbach), the multiple round table (Anaconda-Evans), the bumping table (Campbell), and finally the differential-motion table which is now used extensively for cleaning fine coals.

Jan 1, 1991

By James R. Boulton

Fire detection using Carbon Monoxide sensors is based on the assumption that a rise in the level of Carbon Monoxide in the atmosphere over a fixed, predetermined ambient level is indicative of a fire. The method is simple, reliable, and effective in those mines where the only source of CO is from undesired combustion. Ambience for this purpose is defined as that level of the gas that is present on a day to day basis whose source is not a fire. In a diesel powered mine the level of CO can and does vary so widely from hour to hour and minute to minute that the selection of a predetermined, fixed level represents a compromise between sensitivity and reliability. The compromise is a best of both and worst of both situations and the computer system often resembles the little boy who cried wolf instead of a state of the art early fire monitoring and detection system. Cyprus Coal personnel have developed method of determining the ambient level of CO in the atmosphere on a real time basis and using that dynamic ambient level to determine whether or not a fire exists in the mine. The method has been given the name of Wave Trend Crossing.

Jan 1, 1991

By John A. Cordes, John J. Schanz

INTRODUCTION The economic structures of industrialized countries require a continuous supply of reasonably priced and appropriately processed nonfuel minerals. As a result, national policy makers are sensitive to real or perceived threats to the effective operation of these commodity markets. Their most persistent concerns can be subsumed into the related political economy issues of supply availability and marketplace stability. These concerns are not new. For over a century the "global struggle" for mineral resources has influenced national policies and international relations (Eckes, 1979). During the past two decades the complexity of these issues, if not their place on national political agendas, has increased. Dramatic changes in the structure of mineral industries and in the nature of international economic relations have redefined policy needs and response options. This paper focuses on how selected OECD countries have responded to nonfuel mineral industry issues over the past twenty-five years. Particular emphasis is placed on the impact these policy decisions have had on the size and location of productive capacity and its utilization rates. The results, perhaps, are not surprising for this group of market- oriented economics. While individual cases of significant impact are easy to identify at various times in most countries, the overall importance of policy decisions has not been great. This is especially true for the past decade when excess capacity reached unusual highs of magnitude and duration. Macroeconomic forces and market structure changes played much more important roles. PERSPECTIVES ON THE ISSUES OECD nations dominate the international nonfuel minerals marketplace as producers, consumers and traders. In 1986, these twenty-four countries accounted for 75 percent of the Western world's export trade value in minerals, ores and metals. They imported 88 percent of the total value. During 1966, the respective percentages were 70 and 94. Japan was the world's largest importer in 1986 followed by the US, FRG, UK and France. The same five countries led the 1966 list except that, then, Japan was ranked fourth. Table 1 ranks the fifteen largest Western exporting nations in the two specified years. It also indicates the growth in current export dollars earned in 1986 compared to 1966.

Jan 1, 1989