Search Documents

By T. Krumins, L. Zunti, R. Frischmuth

"Titanium and titanium alloys are commonly selected for pressure oxidation autoclave vent piping and pressure control valve components, as well as autoclave internals and other process piping. In the autoclave vent application, titanium ignition risk is controlled by limiting oxygen concentration, and preventing high gas velocity gas impingement on surfaces. Oxygen concentration is dependent on the autoclave pressure and temperature operating conditions and therefore oxygen concentration and the associated titanium ignition risk is dependent on standard operating procedures, process control interlocks and permissive conditions. It is not uncommon for these standard controls to be deficient during atypical operating conditions, or for operations to deviate from the operating procedures, increasing the potential for a titanium ignition incident. Titanium ignition risk caused by elevated oxygen concentration in autoclave vent systems can be reduced with the introduction of an online autoclave overpressure calculation and the configuration of associated interlocks and permissive conditions. INTRODUCTION High temperature pressure oxidation (>190°C) is a well recognized and versatile metallurgical oxidative pre-treatment process commonly used to liberate gold from refractory sulphide ores and concentrates before conventional leaching with cyanide. Titanium and titanium alloys are highly corrosion resistant in pressure oxidation process conditions and are therefore commonly selected as materials of construction for many components including: autoclave internals, agitators, process piping, and components in autoclave vent systems. Operations that anticipate or have experienced aggressive corrosion in the vent system often have little choice in material selection other than the use of titanium (Krag & Henson, 1992). Titanium is not suitable for use with elevated oxygen concentrations and is considered a restricted material because of its high pyrophoricity and combustion propagation properties (Beeson, Smith, Stewart, 2007). Several serious incidents have occurred in which titanium materials have ignited in autoclave applications (Zawierucha, McIllroy, Million, 1995). In autoclave vent applications, titanium ignition risk is reduced by preventing elevated oxygen concentrations, maintaining low gas velocities, and minimizing the potential for gas impingement on surfaces. Oxygen concentration in the autoclave vapour phase and vent system is dependent on the autoclave operating pressure and temperature conditions and therefore titanium ignition prevention controls typically include process interlocks and operating procedures based on the selected nominal design operating conditions. However, it is not uncommon for these controls to be deficient or for operations to deviate from the nominal operating conditions over time, increasing the risk of titanium ignition. The introduction of an online calculation of autoclave overpressure and a maximum target autoclave pressure as well as associated process control interlocks and permissive conditions can alert the autoclave control room operator and prevent an elevated oxygen concentration from developing, and therefore reduce titanium ignition risk in autoclave vent systems."

Jan 1, 2016

By B. Kyslinger

"In underground mining, machine design is predominantly dictated by mine conditions and individual customer desires. In partnership with Foresight Energy, J. H. Fletcher & Company was tasked to design and manufacture a new roof bolting machine with six independent drilling apparatus on board capable of drilling and bolting the roof and ribs with material handling. This is the first Fletcher® six head machine to be designed and built for the mines in the United States. The machine is intended to work in the Illinois Coal Basin. The objective was to produce a machine capable of drilling and installing six bolts simultaneously with a limited number of operators. The goal of the mine is to decrease the time to bolt a cut to improve the safety level of the current roof bolting method, improve efficiency and to improve the bottom line cost of entry development. The customer wanted four mast feed drills at the front of the machine dedicated to installing roof bolts and then another two mast feed drills behind them dedicated to rib bolts. This dictated the requirement of latched controls, which would allow the operator to start drilling one hole and then latch the controls to be able to move on to the next. To accomplish this, we developed a unique hydraulic latch circuit to maintain operator safety and compliance. Guarding was added to prevent an operator from coming into accidental contact with a latched drill. The result of the design is a machine with a single platform and six independent masts with drillheads: four masts strictly for drilling and installing roof bolts on the front of the platform and then two masts on the back of the platform for rib bolts. The feed and rotation controls at each operator’s station include a latch control for drilling. The latch control will allow the operator to lock in the feed and rotation once the hole has been collared, allowing the operator to move on to the next hole. The rear of the machine is equipped with material handling. There are two material pods with winch controls as well as a mesh rack that includes mesh lift, mesh tilt and mesh sump. The six-head roof bolter allows fewer operators to drill and install roof and rib bolts, which in turn lowers the miners’ roof exposure per cut. This design reduces the operator’s exposure from the inherent pinch points and rotary hazards once he has engaged the latch drilling. Therefore the machine will help to decrease the time to bolt a cut, improving productivity while enhancing the ability to operate the machine safely. INTRODUCTION When mining underground it is necessary to support the roof quickly to prevent it from collapsing after an area has been mined. Since the 1950s, the primary method for supporting the roof has been the installation of roof bolts. Roof bolting is one of the most basic functions yet one of the dangerous jobs in the underground mining operation (1). The Mine Safety and Health Administration’s (MSHA) Health and Safety Accident Classification injury database showed an average of 660 roof bolter operator accidents per year over a 5-year period (1999-2003) (2). The numbers show that roof bolting is the most hazardous machine-related job in underground mining. It represents 39 percent of all machine-related accidents in underground coal mines. In 1993, the U.S. Bureau of Mines conducted a study that has shown the activity of drilling as the most hazardous job task performed by a roof bolter operator, accounting for 31 percent of all roof bolting injuries (3). Almost half (46%) of these drilling injuries were due to falling rocks or coal from the roof. All of these injuries occurred under supported roof. The majority of these injuries (about 99%) are not caused by a major roof collapse but from falls of smaller rock from the immediate roof. This type of roof failure has also been termed “skin fall.”"

Jan 1, 2017

By W. E. Crandall

The Star-Morning mine is a. 1000-ton-per-day lead-zinc producer located in the easterly part of the Coeur d'Alene Mining District of North Idaho. The property includes both the Star and Morning mines which are located on the westerly and easterly portions of the same complex of veins. The mine is 70% owned by the Bunker Hill Company (Gulf Resources, Inc.) of Kellogg, Idaho, 30% owned by Hecla Mining Company, and operated by Hecla Mining Company with head-quarters in Wallace, Idaho. One of the characteristics of mines in the Coeur d'Alene District is that many of the ore bodies extend to very great depths. The Star is no exception, but rather a leading example. The complex of near vertical veins and ore shoots extend some 7000 feet below the surface at present, with a maximum strike length of about 4000 feet. Ore has been mined on 20 separate veins and ore structures. More than 50 miles of headings have been driven and nearly 23 million tons of ore mined since the Morning mine started in.189S. The problems of mining at such depths are formidable temperature on the bottom level is 1100 F and high humidity problem. Pressure from the sheer weight of rock is as high foot. This paper will deal with providing a new access to the deeper levels of the mine and the installation of a hoist and related items to service these levels. By the time development had reached the 7100 level (Figure 1), it became apparent that a different 'hoisting system was going to be necessary if we were going to continue to mine at a profit. The main shaft extended to the 4000 level at which point a ?:3100"'foot winze shaft provided access to the 7100 level. The two hoists were limited to handling 3-ton payloads at 1200 to 1500 feet per minute. Some ores are still produced from above the 4000 level but as these ore reserves become depleted the hoisting of the desired tonnage (1000+/day-) from the lower levels of the mine would exceed the capacity of the existing hoisting system. A decision was made to sink a new vertical shaft at a point well in the south wall of the ore bodies where strong rocks and a minimum of faulting was expected and to purchase and install a new hoist capable of hoisting over 7000 feet. This new' shaft, designated as the No. 4 Shaft, was planned to reach 2000 feet below the 7100 level which was the deepest level at that time. The hoist would be in-stalled on the ,main 2000 Adit level which is used as an access and haulage level to the concentrator and surface plant in Burke.

Jan 1, 1971

By T. A. E. Breen

A new high intensity grinding technology has been developed and is now being commercialized by Hicom International of Australia. This has led to the development and manufacture of Hicom 120 grinding mills which are now being sold internationally for a range of mining industry applications. The first commercial process application has been for the diamond sector, where the ability of the mill to remove host kimberlite rock by attritioning, with no damage to the thereby liberated diamonds, is seen to be a most beneficial attribute. There are, however, many other mineral industry applications for this mill.

Jan 1, 1999

By V. B. Achanti, A. W. Khair

Developing a laboratory procedure for the determination of coal-seam compressive strength has been a subject of discussion for many decades, and the reliability of laboratory determinations is often the subject of debate. A coal seam’s characteristics, the method of sample collection, the specimen preparation method and the testing procedure can often result in drastic variations in the test results. In this paper, the development of a laboratory testing procedure for the determination of coal-seam compressive strength is presented. Two samples that were collected from different coal seams were tested in this study. First, the inherent characteristics, i.e., coal structure. Hardgrove grindability index (HGI), Slake durability index, proximate analysis and mechanical properties (Young's modules and Poisson's ratio), of each coal were determined. The results were used to categorize the coal scams in terms of the characteristics liable to produce variable strength data in typical laboratory tests. Second, two commonly used laboratory specimen shapes, cylindrical and cubical, were tested to determine which shape produced the most reproducible strength values. Third, four loading rates within the static testing range, i.e., 0.007, 0.07, 0.34 and 0.7 MPa/s (1.0, 10, 50 and 100 psi/sec), were used to determine the ideal loading rate. Finally, the number of test samples required to produce strength data within the acceptable standard deviation, considering coal seam characteristics, were established. Background Laboratory testing of coal specimens for the determination of seam compressive strength has been a subject of discussion since the early 1900s. Many researchers have tested coal specimens to estimate coal-seam compressive strength for use in pillar design to insure the safe operation of [ ] mines (Unrug et al., 1986; and Hirt et al.. 1992). Yet, there is a lack of a universal procedure, and, no matter which approach is used, it becomes the subject of intensive debate. A great deal of work has been performed on the subject, and there is much information available in the literature. Some of this work concerns quantifying the influence of specimen shape and size on compressive strength (Bieniawski. 1968: Barron et al.. 1992: Khair and Xu 1994; and Khair 1994). As indicted in the literature, coal is a heterogeneous material, consisting of discontinuities such as cleats and bedding planes, which are likely to produce variable strength results (Holland, 1964; Unrug et al., 1986). Some of the prominent issues that influence the determination of coal-seam compressive strength in the laboratory are: •the collection of a representative sample from a coal seam; •the geometry, i.e., shape and size of the specimens to be prepared and tested: •the loading rate at which the specimens are to be tested:

Jan 1, 1997

By Daniel Connor, O&apos

The Cal-Sag Relief Sewer is a 2.6 m (8 ft 6 in.) diameter 9.1 km (5.7 mile) rock tunnel bored in dolomite for the Metropolitan Sanitary District of Greater Chicago. Included in the project are 18 shafts varying in depth free 70 m (230 ft) to 41 m (135 ft). This paper discusses how Healy/Vanessa reduced costs by eliminating conventional hand excavation by hoisting muck from a high production Robbins TBM (Tunnel Boring Machine) through small diameter drilled shafts and using a trailing rail-utility backup system.

Jan 1, 1985

By Ahmet Unal

Use of radio frequency identification (RFID) technology to solve informational needs in isolated and restricted underground mining environments will be reviewed, giving specifications of some past and currently available systems. The advantages and disadvantages of using various frequencies, system configurations, and specific components, including their construction standards and capability, will be discussed. The remaining challenges to more widespread use of RFID systems for personnel and vehicle tracking will be identified, and recommendations concerning operating environment capabilities will be detailed. Finally, the ultimate requirements for maintaining system integrity during and following a coal mine emergency will be discussed.

Jan 1, 1997

By Ronald R. Rose

Currently six economic heavy mineral deposits are known on the Penholoway Terrace. These are (from south to north) the Green Cove Springs Mine (GCS), Boulogne Mine, Folkston Mine, Mission, Lulaton, and Ludowici. The GCS deposit is located to the west of Highway 17 between the towns of Green Cove Springs and Palatka in the state of Florida and has been mined since 1972. To the north, the erosion created by Black Creek restricts the northern extension of the orebodies and to the south a karst depression and erosion by the St. Johns River restrict southern extensions. The deposit is 20 miles long and up to 4.5 miles wide. Deposit thickness is from 5 feet up to 45 feet. The deposit is a series of regressive barrier island sequences deposited during the Pleistocene along the ancient Penholoway and Wicomico shorelines. The initial transgression of the ocean up to the location of the western Henry orebody was an extensive sea-level still stand as evidenced by the unit thickness and stacked transgressive regressive sequences. This period was followed by sporadic regressing seas and still stands, progressing eastward and stranding the sand bodies which make up the East Extended, TE, and East TE Ridge orebodies. The orebodies are underlain by predominantly non-mineralized fluvial sands and occasional back barrier lagoonal deposited clays. There is a predominance of wetlands on the southern extents of the zone as the surface elevations decrease due to a large karst depression.

Jan 1, 2005

By Douglas R. Shaw

The results are discussed herein of laboratory and pilot scale research which has demonstrated some exciting prospects for the exploitation of refractory gold resources by heap leaching. The research examined practical and cost effective methods of chemical; i.e., non-biological, oxidation pretreatment of refrac­ tory old ores to enable successful conventional cyanide heap leachmg. The work has focused on regenerable chemicals, in order to minimize process consumable costs. A nitric acid method has emerged which offers rapid oxidation rates (eg, 0.5 to 6 hours) on ore samples crushed typically to% to ¾-inch. Gold recoveries in simulated heap leaching tests, after nitric acid oxidation of crushed ores, were as high as approximately 80 to over 90%, in contrast, typically, to negligible gold solu­bilities without oxidation. Nitric acid oxidation was effective when applied to several sulfide-bearing refractory gold ores which required either partial or essentially complete sulfide sul­fur conversion for high gold solubilities in cyanide. Ores rich in organic preg-robbing matter also were treated successfully, as were ores which contain significant quantities of acid-consum­ing constituents. Base metals also were recovered with nitric acid oxidation from some of the ores which contain these ele­ments. The work related oxidation and solution diffusion behav­iors and the important physical, textural, and mineralogical characteristics of the different ore types. Conceptual-level feasi­bility studies have defined the principal capital and operating cost components of the nitric acid method, sufficient to allow reliable comparisons with other oxidative technologies.

Jan 1, 1996

By Peter Zhang, Daniel Su, Mark Van Dyke, Heather Dougherty

The integrity of shale gas wells in longwall chain pillars under the influence of longwall mining is a safety concern for both coal and gas operators. Previous modeling studies of gas wells in longwall pillars have shown that a FLAC3D model can predict longwall-induced stresses and deformations in gas well casings with reasonable accuracy. The predicted casing deformations can be verified by multi-finger caliper survey. This study concerns the influence of longwall mining on eight shale gas wells in a shale gas well pad located in the chain pillars between two adjacent longwall panels under 1,030 feet of cover. FLAC3D modeling was performed to predict longwall-induced deformations in gas well casings based on site-specific mining and geological conditions. Small deformations less than 0.5 in were predicted in the intermediate casing above 600 ft depth, and very small casing deformations less than 0.15 in were predicted below 600 ft due to high abutment pressure and high frictional resistance along the weak bedding interfaces. After the first panel was mined, a 56-arm caliper survey was performed on one of the wells to measure the longwall-induced casing deformations in the intermediate casing. The predicted casing deformations were then compared with the measured deformations, which indicated that the prediction was generally in good agreement with the measurement in terms of deformation locations and magnitudes. Findings from this study provide valuable information not only for stability assessment of shale gas wells in longwall chain pillars but also for developing engineering guidelines to preserve casing integrity through adequate pillar and casing design.

By Ernest E. Thurlow

"Western Coal" in this paper is limited to those deposits of subbituminous coal and lignite in the States of Montana, Wyoming, and North Dakota. The characteristics of the coal are discussed as well as the history of mining and current mining operations for steam coal. The future of the region is tied closely to the ultimate conversion of coal to oil and gas products. Problems of industrial water supply and environmental considerations are covered together with a brief review of current legislation's actions affecting strip mining.

Jan 1, 1973

By MARK J. VANARELLI

Estimating groundwater inflows in rock deep tunnels is critical to the safety of personnel constructing the tunnel and the cost of construction. This paper presents two case studies for estimating steady-state groundwater inflows into deep rock tunnels. The case studies included the Chattahoochee and Nancy Creek tunnels. In this paper, statistical methods were applied to packer test data obtained from exploratory borings during geotechnical site investigations. A semi-empirical procedure was utilized for estimating groundwater inflows into these deep rock tunnels. The Chattahoochee and Nancy Creek tunnels are deep rock tunnels which exhibit radial flow conditions. For the radial flow condition, a statistical analysis presented in this paper indicates that the semi-empirical procedure works well; however, variations in the procedure and/or an insufficient amount of testing could lead to underestimations of the inflow quantities. Packer test data plotted in histograms were observed in all cases to be log-normally distributed for the radial flow condition. Modeling using Monte Carlo simulations was observed to be an effective tool for removing irregularities in the distribution of the data and incorporating high-end permeability data to derive reasonable groundwater inflow estimates.

Jun 13, 2021

By S. P. Winkelmann

The expansion in gold production in the Carlin 'Trend over the last few years has been one of staggering proportion. To increase gold production while minimizing capital requirements and providing for the safe and efficient mining and processing of ores has required a tremendous effort by the Mine Engineering group at Newmont Gold. This paper discusses the organizational changes implemented to effectively deal with a full range of engineering problems and how the Newmont Gold Mine Engineering group dealt with these problems. Specially developed computer software and their applications will be explained. Improvements in the techniques used in converting geologic resources into reserves, and in scheduling the mining of multiple pits to feed multiple processing facilities, as well as ore control procedures are presented. Current mine engineering practices are discussed.

Jan 1, 1990

By Ben L. Seegmiller

How to obtain optimum slope angles for future open pit mines using the rock mechanics approach is the subject of this paper. In the past ten years significant developments in open pit rock mechanics have come about. This has been due to the mining industry's need for the steepest, yet safe, pit slope angles attainable. Requirements for economically achieving slope stability and the actual payoff that may be achieved through stability studies have been previously discussed', by stability engineers. While the emphasis has generally been placed on the concept of "stable slopes" in the past, it is suggested that emphasis now be placed on "optimum slopes" or "optimum slope angles". A definition of an optimum slope angle is one which (1) is as steep as possible and practical from orebody and mining constraint standpoints and yet, (2) maintains the accepted standard of safety defined by a safety factor against failure and/or a probability of failure. In other words, the emphasis is placed on achieving practical stability results as defined by safety and economic considerations, as opposed to simply achieving stability. The essential purposes of this paper are to (1) outline the need for optimum slope angles, (2) discuss the procedures for using the rock mechanics approach in slope angle design for a future open pit and (3) specify the end results that may be achieved by using such an approach. While the basic concepts and recommendations outlined in this paper may be equally applicable to soil as well as rock slopes, the emphasis and procedures have been directed at rock slope angle design.

Jan 1, 1976

"From April 22 to 28, the eyes of the tunneling and underground construction world will be on San Francisco, CA, as the world’s most influential underground construction industry leaders gather at the Moscone Center for the 2016 World Tunnel Congress.Recognized as the most important international annual meeting for the industry, the 2016 version comes to the United States for the first time in 20 years and will be hosted by the Underground Construction Association of SME (UCA of SME). The conference will be held in lieu of the UCA’s biennial North American Tunneling Conference and will bring the strengths and resources of the UCA of SME and the International Tunnelling and Underground Space Association (ITA). The result will be a conference with unmatched technical programming and a showcase of more than 200 exhibiting companies.A program committee led by Randy Essex of Mott MacDonald, Lonnie Jacobs of Frontier Kemper Constructors, Michael Mooney, of the Colorado School of Mines, Priscilla Nelson, of the Colorado School of Mines and Amanda Elioff of Parsons Brinkerhoff formed the program committee and worked for more than two years to build the program. The result is four technical sessions with five tracks in each session and 185 oral presentations.“One challenge was the sheer size of the group that would be assembled, perhaps 2,500 attendees or more, and the large number of abstracts we were likely to receive,” said Essex. “ We investigated extending the conference a fourth day, but that was not workable with the Moscone Center. We settled on having five concurrent technical tracks – something that has not been attempted in past NAT or RETC conferences to my knowledge. The next step was to develop suggested session titles that would span the breadth of subjects that would interest conference attendees as well as serve the conference theme.”"

Apr 1, 2016

By Daniel K. Dysinger

Capital resource budgeting is the way managers of publicly held companies fulfill their fiduciary responsibility to maximize the wealth of stockholders. Managers maximize shareholder wealth by allocating investment capital to the most productive of competing alternative projects. Managers do this in a manner that maximizes the net present value of the firm's future cash flow. The techniques of cash flow analysis are the primary tools available for selecting a corporate portfolio of projects that meets or exceeds the rate of return expected by shareholders. The reliability of cash flow analysis hinges on the ability of managers to forecast the future values of individual components of cash flow. The accuracy and reliabil¬ity of forecasting determine the soundness of capital investment decisions and, ultimately, determine the value of the firm.

Jan 1, 1997

By Ihsan Berk Tulu, Mustafa Can Suner

The synthetic rock mass (SRM) approach and discrete fracture network (DFN) model, generated from the field surveys, are novel methodologies to study fracture rock mass behavior. In this paper, SRM and DFN methodologies were used to understand the influence of natural fractures on the mechanical response and failure mechanisms of stone mine pillars. First, a multi-stage up-scaling procedure with the homogenization process is established. Later, a stochastic sampling process on the SRM model to have further insight on the stone mine pillar mechanics is performed. Two-dimensional Universal Distinct Element Code (UDEC) is utilized to represent intact rock with the Voronoi-Trigon discretized blocks and to capture fractured rock mass behavior. The laboratory-size limestone mine rock specimens are systematically up-scaled to the average width of the field-size stone mine pillars. Then, the DFN model, generated from field data, is sampled to construct the SRM of the field-size pillars. By doing so, the effect of discrete discontinuities on pillar stability is studied by assessing the pillar strengths and failure mechanisms in various width-to-height ratios.

Jul 8, 2022

The Kinross DeLamar Mine has been operated for more than 17 years producing precious metals dore' from ores, principally silver bearing with associated gold co-products. In late 1995 a new orebody was commissioned, the Stone Cabin orebody, and the site began a phased shift from silver dominance to gold dominance in terms of precious metals revenue. The Knelson Concentrator was selected to remove gold from a portion of the cyclone underflow stream in the grinding circuit. This paper describes the development of the flow sheet, specific mineralogical impacts on Knelson product and downstream materials, and impacts on mine/mill grade reconciliation.

Jan 1, 1997

Editor's note: Biographical information about Ihor Kunasz, president, Newmont Uzbekistan, can be found in the February 1998 issue of ME, page 94 and in the May 1996 issue, page 92. Your personal assessment of the minerals business. Gosh! When I think about what has happened to the minerals industry over the past 27 years that I have been a member of SME! There have been fundamental structural changes in the industry. And I think that SME has been quite successful in coping with these changes as well. There has been a reorientation in how the minerals industry does business. It used to be called rationalization. Today we call it reengineering. In addition, the minerals industry has become more complex and more global. Shareholders have become more vocal and demanding in the management of the business, asking for protection of their shareholders' value. In the 1980s, a fundamental change was precipitated by a merger and acquisition fever in all industries, including the minerals industry. Raiders such as T. Boone Pickens put enormous demands on companies that, in turn, had to spend substantial management time to fend off the raiders. This resulted in a major restructuring of the mining houses. Today, for example, Anaconda, Kennecott and Amax are only historical names.

Jan 1, 1998

By B. M. Eiter, J. Hrica, D. R. Willmer

"Mineworkers are routinely tasked with making critically important decisions about whether or not a hazard presents an imminent danger. Researchers from the National Institute for Occupational Safety and Health (NIOSH) collected formative data to investigate mine safety professional perspectives on workplace examinations, which revealed a potential gap in how mineworkers are assessing risk. During interviews, participants indicated having processes in place for what should be done once an imminent danger situation is identified. Critically, however, they report having no systematic methodology for mineworkers to use to determine if a hazard is considered imminent danger. While this is important for all imminent danger situations (e.g., failure to lockout/tagout), it is especially important for those situations that are not immediately recognizable as imminent danger. In this paper, we identify and describe, three distinct categories of imminent danger complexity and discuss potential steps that could lead to improved identification of imminent danger situations. Finally, we identify potential practices to incorporate into risk management efforts, including feedback, communication, and specialized training to increase awareness of imminent danger situations. INTRODUCTION In recent years, the metal and nonmetal (M/NM) mining sector, as categorized by MSHA, experienced an increase in the number of fatalities occurring at mine sites. From 2013 to 2015, 69 mineworkers were fatally injured; that is twice the number of fatalities that occurred in each of the previous two years (MSHA, 2015a). As a way to address this increase, the Mine Safety and Health Administration (MSHA) issued a program policy letter (P15-IV-01) suggesting that “miners would benefit from rigorous workplace examinations conducted by experienced and trained examiners (MSHA 2015b).” The goal of workplace examinations is to find hazards in the field and mitigate them before they cause injury or death to mineworkers. While it is important to identify all hazards in the workplace, it is critically important to identify those hazards that are considered imminent danger because they require an immediate response to avoid a severe or even fatal injury."

Jan 1, 2018