Search Documents

By Ven Mercade

The flotation of calcite has been studied by many investigators, especially in terms of type of collector; pH; and metal ions that activate and, more importantly, depress the flotation of calcite (1)(2). Research was extended to the investigation of the effect of polyvalent metal salts and sodium silicate using these materials added separately or in mixtures (3)(4)(5)(6). Flotation of calcite was also studied with respect to its function as a carrier in the beneficiation of kaolin clays by Ultraflotation (7) (8) (9). The carrier used in Engelhard Minerals & Chemicals Corporation's industrial Ultraflotation operation is calcite. This fact, coupled with the continuing interest in Ultraflotation phenomena, led to a study to determine the effect of polyvalent metal-silicate hydrosols on the flotation of calcite.

Jan 1, 1978

By G. T. Daware, M. J. Chaddha, S. P. Masurkar, P. G. Bhukte, A. Agnihotri

JNARDDC has evaluated bauxite deposits of India from the geo-technological point of view. During the evaluation studies, it was observed that bauxite deposits are associated with saprolite resources. During bauxite mining, various low-grade materials such as saprolite, laterite and low-grade bauxite are generated. These materials typically have low-alumina, high-iron oxide and high-silica content. Owing to their inferior quality, these materials cannot be used for alumina production and hence remain unutilized at the mine site. For the present study, the saprolite samples were collected from the Western Ghats bauxite deposits in India. The sintering studies were conducted on saprolite granules using a variety of parameters. The sintered granules were characterized, and their properties determined. The test results showed that bulk density, apparent density, porosity and refractoriness (PCE 1645–1659 °C) of the aggregates were within the range of refractory specifications. The feasibility tests carried out at the refractory industry indicated that the developed aggregates are suitable as refractory material and can substitute for calcined clay. Currently, high-purity clay resources used in the refractory industry are limited and fast exhausting; therefore, the industry is likely to face an acute shortage of raw materials, which will become more critical in the future. Therefore the sintered granules (aggregates) developed from saprolite, which is a mining waste, provide a low-cost, eco-friendly solution for the fast-exhausting resources of the high-purity clays. The developed process may change the Indian bauxite mining scenario because saprolite may substitute as a potential raw material for the refractory industry.

Apr 12, 2021

By W. R. Reed, Y. Zheng

A recent study conducted by the National Institute for Occupational Safety and Health (NIOSH) evaluated the roof bolter canopy air curtain (CAC) systemin a blowing face ventilation system, demonstrating its effectiveness and illustrating the CAC protection zones. This study evaluates the roof bolter machine CAC while operating in an exhausting face ventilation system. This study considers two similar locations to allow comparison with the previous blowing face ventilation (Zheng et al., Min Metal Explor 36(6):1115–1126, (2019)) study: (1) a roof bolter machine bolting the roof at 20 ft (6.1 m) from the face and (2) a roof bolting machine bolting at 4 ft (1.2 m) from the face. The environment introduces 6.0 mg/m3 of respirable dust to represent the roof boltingmachine operating downstreamof the continuous miner. However, the exhausting face ventilation uses an exhaust curtain with 9000 cfm (4.25 m3/s) of air. Two roof bolter machine working positions are simulated with the use of dual drill heads in the inward position for two inside bolts and in the outward position for two outside bolts. The influence of the CAC on airflows and dust dispersion is evaluated with the CAC operating at 250 cfm (0.12 m3/s) with dust reductions ranging from 39.5 to 82.8%. When the roof bolter machine operated close to the face, increasing CAC airflow was required for adequate protection since the dust reductions can be as low as 39.5%. Additional CAC airflows of 350 cfm(0.17 m3/s) and 450 cfm(0.21 m3/s) were evaluated and demonstrated that dust reductions increased to 59.7% (350 cfm) and 72.0% (450 cfm) for the worst location where the roof bolter operators located.

Aug 26, 2020

By Guoqing Li, Hao Wang, Nailian Hu, Victor Tenorio, Jie Hou

This paper presents an algorithm for optimizing the scheduling of trackless equipment in underground mines. With the shortest working interval and maximum productivity as goals, a genetic algorithm (GA) is used to solve the problem, and obtain the optimal working sequence with the most suitable equipment configuration possible. The input for the proposed method is the number of units and capacity of trackless equipment, the production process, ore amount in stopes, and the distance between stopes. The algorithmis verified using four setups of 5 stopes with 5 cycles, 5 stopes with 15 cycles, 10 stopes with 10 cycles, and 10 stopes with 30 cycles. The solution time of the algorithmis no more than 20 min, which is acceptable for practical applications. The results show that the setup of 10 stopes with 30 cycles is closer to the actual production of the mines, and the optimization model can effectively improve the operation efficiency. In this scenario, the robustness of the optimization is tested by simulating equipment failure events. Under the condition of 8% failure rate, the operation time is extended over 3.21–14.56% than expected, which represents strong robustness. The algorithm can quickly provide a feasible and effective solution for the production scheduling decision of trackless equipment in underground mines.

Aug 12, 2020

By D. L. Romero

The Line Creek Mine is operated by Crows Nest Resources Limited, a wholly owned subsidiary of Shell Canada Resources Limited. It is located approximately 25 km north of Sparwood in southeast British Columbia (refer to figure 1). The Line Creek coal deposit is part of the Upper Elk Coalfield in the East Kootenays. The coal is a medium volatile, low sulfur, bituminous coal and is used as a coking coal. Coal close to the outcrop is typically of low F.S.I. and is processed for thermal use. The present pits have a total coal reserve of 30 million clean tonnes and is a multi-bench, open-pit operation. The coal is recovered by front shovel and backhoe combination, and hauled to the plant with a fleet of 120-tonne and 40-tonne capacity trucks. Line Creek is unique in that it can simultaneously treat both metallurgical and thermal coal in separate processing facilities (refer to figure 2). Run-of-mine coal is delivered to the truck dump. The plus 50 mm material is scalped off and reduced to minus 50 mm in two rotary breakers. The raw coal is then conveyed to one of five, 5000-tonne capacity, silos. Typically one silo is used for thermal coal and four for metallurgical coal (refer to figure 3).

Jan 1, 1991

By Shanming He, Jinliang Wang, Xiaoming Wang, Chunfa Liao

Large amounts of manganese-rich slag were generated from smelting low-grade manganese ore containing high iron and high phosphorus in electric furnace or blast furnace, which contain 25–40 mass% Mn. This paper describes an efficient hydrometallurgical process for the utilization of high manganese slag instead of conventional usage of pyrometallurgical route for manganese recovery. Pressure acid leaching of manganese-rich slag using air as pressurized gas is studied systematically. The effects of mass ratio of manganese-rich slag to pyrite, concentration of sulfuric acid, leaching temperature, partial air pressure, leaching time, and liquid-solid (L/S) ratio on the separation of manganese with other main impurity components were investigated comprehensively. Under the following optimal process conditions, weight of manganese-rich slag powder,100 g; mass ratio of manganese-rich slag to pyrite, 20:1; sulfuric acid concentration of 140 g/L; air pressure of 0.6 MPa; leaching temperature of 140 °C; leaching time of 1 h; L/S of 7:1; ore size of 75–80 μm; and stirring rate of 600 rpm, the extraction rate of Mn reached 94%, and the dissolution percentage of Si, Al, and Fe are as low as 2%, 6%, and 10%, respectively. The leaching slurry presented a good solid-liquid separation characteristic. The silicic acid formed during sulfuric acid leaching manganese silicates was converted to filterable dehydrated SiO2 particles which precipitated in the residue under the condition of higher temperature with higher pressure. The effect of adding pyrite may be to reduced iron ions and decreased the output of iron hydroxide colloid and also reduced MnO2 to manganese sulfate in sulfuric acid leaching. Thus the formation possibility of colloid such as silica gel and iron hydroxide was decreased, and higher yield of manganese sulfate could be achieved.

By Marcos Vieira, Gil Vilela, Wanderson Silvério, Livia Faustino, Pierre Fernandes

New global industry standards and regulatory changes regarding mining tailings management are driving installation of tailings filtration plants to decommission existing tailings dams and implement dry stacking. Target of this project was to reduce ultrafine slime tailings deposition. Previous investigation at Samarco concentrator has showed a 35% decrease in tailings filtration throughput when feeding a mix of 95% flotation tailings with 5% slime tailings (compared with 100% flotation tailings), also worsening geotechnical aspects such as material workability during dry staking. Industrial trials using a proper filter aid at tailings filtration plant feeding a mix of 94% flotation tailing and 6% slime tailing (equivalent to 30% of total slime generation) have provided filtration performance maintenance (throughput and cake moisture), and dry stacking the dewatered material. Results achieved will enable life expansion of existing slime disposal structures, as well as potential life of mining extension. Furthermore, reagent chemistry influence is discussed by the light of geotechnical aspects, which has been showing improved KPIs, such as workability, compressibility and permeability.

Feb 1, 2025

By Gerald H. Luttrell, Seyed Hassan Amini, Aaron Noble

One of the most important processing engineering tools for designing mineral processing facilities is linear circuit analysis. This technique, originally conceived and developed by Meloy, Williams, and Fuerstenau nearly four decades ago, provides fundamental insights regarding how unit operations interact and respond when arranged in multi-stage processing circuits. Researchers have successfully utilized this tool to improve the operating performance of industrial processing circuits incorporating coal spirals, magnetic separators, mineral spirals, and eddy current separators. More recently, advanced versions of this tool have also been developed to provide a standardized framework for circuit mass balance calculations, to output exact analytical solutions to mass yield and value-based efficiency expressions, and to estimate uncertainty propagation in separation circuits. This article reviews the historical development of linear circuit analysis, describes how the technique has evolved to address more complex circuit design problems, and presents industrial case studies that highlight the importance of this process engineering tool.

By Lana Alagha, Fardis Nakhaei, Jose L. Corchado-Albelo

Tellurium (Te), a critical mineral for solar energy technologies, faces supply risk challenges that drive the development of diversified and robust production routes. This research focused on improving Te enrichment from copper tailings (CT) produced from copper porphyry (CP) ores processing, addressing the loss of ~90% of Te minerals to tailings in the flotation process of CP ores. Gravity separation and froth flotation processes were used as possible enrichment routes of Te-bearing minerals (i.e., pyrite) in CT. In the froth flotation process, synergistic combinations of reagents were tested to achieve an acceptable enrichment ratio of Te minerals. Comprehensive characterization analyses showed significant Te enrichment in the flotation concentrates. Tellurium was recovered at 90%, while the grade of Te in the concentrates was 1.4 ppm using a xanthate collector and glycol frother compared to <0.5 ppm in the flotation feed. Findings showed that Te-minerals’ enrichment was also feasible in CT using the proposed combined concentrations routes (i.e., gravity separation followed by froth flotation) by looking at Fe, Cu, and S enrichment. This study also highlighted the importance of understanding the deportment of Te minerals in different process streams to develop and optimize efficient enrichment practices.

Feb 1, 2024

By C. Webb, M. A. Tuck

This paper describes the application of a cable disc elevator to continuous lift ore vertically from underground mines. Application of this system requires the tensions developed within the cable must remain within the carrying capacity of the cable including applicable safety margins. A critical element occurs at starting the system when it is fully loaded which requires the force developed by the system to exceed the static friction forces. This paper describes the laboratory rig developed to investigate the static friction forces. Details of the results of tests on three different ores for both dry and wet conditions are given. These results are discussed.

Nov 19, 2020

"A fire design innovation of the concrete lining of the Ohio River Bridges East End Crossing Tunnel has been developed. As a result from a fire suppression and tunnel ventilation system, the project design Heat Release Rate (HRR) was able to be constrained from 300 MW to about 50 MW. With this reduced HRR, concrete lining without passive fire protection may be acceptable, if the tunnel concrete lining will not result in explosive spalling during the designed fire event. Concrete explosive spalling test was proposed to verify this assumption. Since no standard concrete fire explosive spalling testing procedure exists, a project specific testing procedure was developed and fire tests conducted. From fire test results, it is concluded that the proposed tunnel concrete lining, in conjunction with the proposed fire suppressing and ventilation system, will not experience explosive spalling and does not require a passive fire protection system. INTRODUCTION The Ohio River Bridge East End Crossing Tunnel is part of a Public Private Partnership project, which connects transportation network between Louisville, Kentucky and southern Indiana. Located in Louisville, Kentucky, the twin-tube highway tunnel provides northbound and southbound lanes of the Kentucky approach to a new bridge across the Ohio River. Tunnel lengths are approximately 1,675-ft and 1,685 for the northbound tube and the southbound tube, respectively. Connected by two cross-passages, both tubes have a roadway width of 40-ft, for 3-lane traffic, and a vertical clearance of 26.5-ft.The Tunnel was constructed by drill and blast method with shotcrete and rock dowels as initial ground supports. The final tunnel lining consists of 16 inches cast-in-place concrete lining and 20 inches invert slab, with a waterproofing system around the tunnel perimeter. Two (2) tunnel side drains and one (1) invert drain were provided for each tube. This paper describes the rational in assessing fire design requirements of the tunnel final concrete lining, to answer the question whether a passive fire protection system is needed or not."

Jan 1, 2016

By Elena Chiriotti, Federico Valdemarin, Jan Cenek

"SUMMARY The “28 May Station” is the only transfer station between the existing Green and Red metro lines in Baku. As part of the huge development strategy of the metro network, the complete separation of the existing underground lines has been planned at this location, in order to simplify the operation of the future metro system. The extreme challenge of the project is represented by the need of achieve the separation of such lines over a breakdown of the operation of just five weeks. The lack of direct access from the surface, a complex geology with artesian water layers, a congested underground space and sensible buildings represent additional constraints. The chosen design solution consists in creating a complex steel pipe jacking frame around the operating tunnels and then excavating under such frame two large caverns where the separation of the existing lines and the construction of the new metro tunnels will be achieved. Soil treatments have been conceived to mitigate the geotechnical risks and to reduce possible impacts on the existing structures. The paper illustrate the challenges of this extraordinary project, one of the most complex underground structures under study, the design solutions and the risk management approach used to manage the complexity and to design the mitigations measures. INTRODUCTION The metro network in the capital of Azerbaijan is rapidly growing together with its metropolitan area. The beginnings of the existing metro system started in Baku in 1967 in Soviet times. To date, only two lines (Green and Red) are in operation with a total length of 34 km, including 23 stations. The future network will be much wider: besides the construction of three completely new lines and the extension of two existing lines, the whole metro project includes the development and modernization of the existing metro sections. A consortium formed by Systra (leader), Mott MacDonald (Praha) and Saman (Korea) awarded the contract for the preliminary and detailed design of infrastructures for the extension of Baku Metro Network. This extension consists in 83 km of new lines and extension of existing lines. As part of this modernization project, the connection of the Green Line at the 28 May / Cefer Cabbarli Stations, focus of this paper, represent also it’s ""Achilles' heel"" given that the already very congested system have only one transfer station."

Jan 1, 2016

By Z. Sample

"INTRODUCTION This past year commodity prices continued their dip with increased volatility causing market values to slide another 16% putting increased pressure on even the largest companies to improve their free cash flow.[1] Without a recovery in commodity prices in sight, companies must find a sustainable method to improve returns in the current economic climate. In an effort to improve plant sustainability, the mineral processing industry is investing in advanced automation technologies and innovative processing methods that are both more reliable and more efficient than ever before. One such breakthrough technology is Heap Leaching (HL). This method of extraction has certain advantages over traditional metallurgical methods making previously unsustainable operations economically feasible. While HL is already seeing use in the gold and copper industries among others, recent developments may allow for the use of HL to process primary sulfide ores which make up about 80% of today’s ores.[2] For this reason, this emerging technology is poised for exciting growth. Unfortunately, as with any process change, the implementation of HL projects requires significant training on both the control system as well as the underlying process, and further, due to the complex nature of the HL process, this can be a particularly difficult task. DEMOGRAPHIC TIME BOMB Even before the implementation of these new technologies, the availability of the skilled workforce has already become a significant problem for the mining and mineral processing industries. From a survey of 912 mining professionals, Stratum International found that a mere 0.4% of senior level candidates were between the ages of 25 and 34 and a similar proportion aged over 75 years.[3] This indicates that there is both a deficiency of young skilled workers and a skilled workforce that is retiring earlier than the previous generation. Combined with data published by the US Department of Labor stating that the median age of the mining workforce is approaching 50 years old, research suggests that up to 50% of skilled mining and mineral process professionals are expected to retire in the next 5 years, leaving with their irreplaceable knowledge and experience.[4] While it is projected that the labor pool will be sufficient to fill open positions, the real question is if this young workforce will have necessary skill sets and experiences. In addition to a rapidly aging workforce and an inexperienced labor pool, a study done by the Oil and Gas Journal showed that it takes about 7 years, on average, for new workers to achieve a level of competency that permits them to assess risks and appropriately make decisions.[5] Not only is this figure is in direct conflict with the typical tenure of 5 years in one position meaning that the thinly spread skilled labor will be required to become senior staff before they are able to achieve competency in their current role, this also means that these millennials are not given the opportunity to become competent in their role before the retirement of the more experienced workforce."

Jan 1, 2016

By I. Ward, E. Milosavljevic, M. Botz

"The silver nitrate titration method is a rapid and acceptably accurate means of analyzing for cyanide in leach solutions that contain primarily free cyanide. However, in leach solutions containing elevated levels of copper, the titrimetric method overestimates the concentration of free cyanide and underestimates the concentration of weak and dissociable (WAD) cyanide. The authors have developed a modified potentiometric (MP) titration method for determining WAD cyanide that overcomes issues associated with high copper levels in solution. The new MP-WAD method involves addition of a chemical ligand to the sample prior to silver nitrate titration to release cyanide bound to copper. Once released from copper, cyanide in solution is no longer affected by the presence of copper, and titration results are quantitative rather than empirical. In multiple laboratory trials with synthetic solutions and complex actual leach solutions, analytical results obtained with the new MP-WAD method were found to be within about ±5% of analyses obtained with the USEPA OIA-1677 WAD cyanide analytical method.IntroductionThe silver nitrate titration method is widely used to estimate the concentration of cyanide in leach solution for purposes of cyanidation process control. Cyanide determined by silver nitrate titration is commonly referred to as “free” cyanide, but frequently should be referred to as “titratable” cyanide. By definition, free cyanide is the sum of the concentrations of aqueous hydrogen cyanide HCN(aq) and the cyanide anion CN- (ASTM, 2010). Titration will only yield a reasonably accurate measurement of free cyanide when metal-cyanide complex concentrations (e.g., cadmium, copper, mercury, nickel, silver and zinc) in solution are low. In other words, titration will only yield a reasonably accurate measurement of free cyanide if the solution primarily contains free cyanide."

Jan 1, 2015

By David L. Kuck

Siderophyle platinum-group metals and sane gold are a thousand times more abundant in metal and chondritic meteorites than in terrestrial or lunar rocks. Type I and II carbonaceous chondrites contain granules of the high boiling point metals W, Re, Mo, Ir and Os. Metal meteorites and the metal fractions of other chondrites contain siderophyle Pt, Pd, Ru, Rh, Os, Ir and Au. Spectra of sunlight reflected from asteroids, when compared with those of meteorites and specific minerals, provide a rough classification and guide to sources of precious platin-group metals.

Jan 1, 1982

By E. Yigit

Hydrometallurgical production of zinc from concentrates is generally carried out by H2SO4 leaching. For the smooth operation of this process, some harmful components must be removed from the leach solution before the electrolysis stage; MgO is one of these compounds. Zinc concentrate samples from the Mount Isa mines were used in leaching tests. Leaching tests with an aqueous solution of H2SO4 and SO2 gas were carried out at various temperatures, pH levels and leaching durations. While duration and the pH value of the solution were effective parameters in H2SO4 leaching, temperature and pH were more effective in SO2 leaching for the removal of MgCO3 and CaCO3. Removal of MgCO3 and CaCO3 was generally achieved at low pH values. The results show that SO2 gas can be a good alternative to sulfuric acid in the leaching of MgCO3 and CaCO3

Jan 1, 2010

By Felicia F. Peng

The manganese removal from aqueous solution containing high Mn2+ concentration by adsorption and oxidation was studied using manganese oxide particles as the adsorbent. The operating parameters including pH, flow rate, initial manganese concentrations, and oxidant dosage affect the performance of Mn2+ removal were evaluated in a laboratory packed column. In the multi-column adsorption tests, each additional column doubled the time for complete manganese removal. No further decrease of pH was also observed once it was lowered to pH 4.5 to 5. This finding implied the possibility of complete high manganese removal without further pH adjustment during adsorption. Oxidation of Mn2+ by dissolved oxygen was found to be insignificant for manganese removal for high Mn2+ concentration. Adsorption was the predominated mechanism involved with manganese removal. Extremely low H+/Mn2+ stoichiometry compared to the reported values was measured. These low values suggested that different adsorption mechanisms such as chemisorption other than H+/Mn2+ ion exchange might play an important role at low pH. This paper presents the quantity and explanation of the results obtained for the mechanism of adsorption and oxidation of high concentration manganese on the manganese ore particles.

Jan 1, 1997

By John R. Riede

Most modern crushing and grinding facilities are automated to some degree. Some, of course, have a very minimum of automatic control whereas others utilize very complex control equipment. However, with very few exceptions, the re has not been a new basic control philosophy applied in this field in the past seven years. The philosophy has been broadened in scope and applied to larger plants, some of them with data logging and so- called computer control, but almost always the same tried and proven basic control philosophy is the basis for the control system. New types of control devices to better implement the automatic control have been developed and are continuing to be developed. These devices and their application will be explained and the advantages and disadvantages of each will be discussed. Automatic lubrication of plant equipment is most essential, but this paper will not cover these systems. The use of data logging and computer analysis of the data obtained is fairly recent and it is hoped that by careful analysis of this information that new and better basic control philosophy will be forthcoming. This paper will describe the basic philosophy applied in its simplest form to several types of crushing and grinding equipment, and it will describe how it is being expanded to more complex systems. Some of the economics with regard to first cost, return on investment and maintenance will be covered.

Jan 1, 1965

By D. C. Fuller

CoaLiquid, Inc. (CLI) has been in the coal- oil-mixture (COM) business for over five (5) years. The initial pilot processing facility was replaced by a 2000 barrel per day commercial production facility in August of 1979. For over two (2) years CLI has been expanding its efforts and conducting large scale production and combustion demonstrations successfully in many locations across the United States. To facilitate the marketing effort, CLI has recently constructed a special trailer containing all equipment needed for a temporary COM retrofit. CoaLiquid has conducted commercial scale combustion demonstrations in the following types of combustion units: kilns, calciners, industrial boilers, blast furnaces and driers.

Jan 1, 1982

By P. M. Krishna

An example illustrates the use of ASTM Standard E901-82, Classification System for Uranium Resources. The example demonstrates the dynamic nature of the process of classification and attests to the necessity of addressing both the aggregate needs of broad-scale resource planning and the specific needs of individual property evaluation. Problems that ,remain in fixing the classification of a given uranium resource include the uncertainty in estimating the quantity of undiscovered resources and resolving the differences that may exist in deciding when the drill-hole spacing is adequate to determine the tonnage and grade of discovered resources.

Jan 1, 1983